Search

Over 50 years ago, a marine estuary was converted to a wastewater stabilization basin for treatment of primarily pulp and paper effluent. As a result, the basin was immediately converted to a "freshwater" environment and subsequently accumulated a thin layer of black, organic-rich sediment containing varying amounts of dioxins and furans, metals, polycyclic aromatic hydrocarbons, and petroleum hydrocarbons. Previous studies on the site have shown that the majority of this contamination in the basin appears to have been contained within this black sediment layer and not migrated to any significant extent into the original underlying marine sediments. The purpose of this study is to examine sediment porewater chemistry changes that have occurred over 51 years of operation of the stabilization basin with the intent of better understanding why contamination has been minimal into the underlying natural marine sediments. Field and laboratory testing is presented to characterize the physical, chemical, and mineralogical sediments in the basin. Porewater chemistry profiles obtained from this work are then used in combination with a one-dimensional contaminant transport model to examine the role of diffusion, sorption, and upward groundwater flux in the porewater profiles found for the sediments. [ABSTRACT FROM AUTHOR]

RNA interference (RNAi) is a useful tool to assess gene function by knocking down expression of a target gene and has been used successfully in domestic and laboratory organisms. However, the use of RNAi for functional genomics has not fully extended into ecological model organisms in natural environments. Assessment of gene function in the wild is important because gene function can be environmentally and context dependent. Here, we present a case study using RNAi to assess gene function in wild paper wasps Polistes metricus, to test roles for two candidate genes ( NADH dehydrogenase ( NADHdh) and retinoid and fatty acid binding protein ( RfaBp)) in the development of reproductive castes. Previous studies have shown that these genes are upregulated in larvae that become queens compared to workers, but this pattern was reversed in the laboratory, making field-based studies necessary. We orally administered dsRNA to larvae in field colonies and found evidence of a short-term knockdown followed by a compensatory rebound in expression for RfaBp. We also observed the predicted worker-like decrease in lipid stores in NADHdh dsRNA treated wasps, suggesting a possible role for NADHdh in caste development. We discuss our results in the context of challenges for using RNAi for functional genomics in ecological model organisms in the field. [ABSTRACT FROM AUTHOR]

A novel, simple, and low-cost spray painting technique has been developed for the fabrication of microfluidic paper-based devices. The devices that we developed utilize aerosol spray paint to build hydrophobic barriers and employ a hole puncher to obtain paper-based patterned layers and paper dots without using any specialized instruments (e.g., without a laser cutter). The entire manufacturing process is extremely simple, inexpensive, and rapid, which means that it can be applied broadly. Furthermore, the application of the device to iron detection was demonstrated. A linear relationship between the colour value and the iron concentration was observed from 0 to 0.02 g/L. The developed microfluidic paper-based device for iron detection exhibited a low detection limit (0.00090 g/L), good selectivity, and acceptable recovery. [ABSTRACT FROM AUTHOR]

The Global Navigation Satellite System (GNSS) has emerged as a practical and effective technique for studying slow and steady geodynamic movements, enabling continuous monitoring and precise quantification of deformation over different timescales. In Morocco, a network of GNSS stations has been established, offering valuable insights into tectonic processes. This paper focuses on investigating the geodynamic motion of the northwest Moroccan Atlantic Margin. By utilizing GNSS data, subsidence rates and horizontal velocity fields were determined for the first time, providing valuable information for oil and gas exploration activities. The study reveals an active uplift rate of 1 mm/year and a westward horizontal motion of 2.04 mm/year in the Essaouira segment. The paper presents a case study of the Essaouira–Agadir basin (EAB) onshore segment and investigates the anomalous displacement observed in this region compared to other coastal GNSS stations. Possible explanations for the observed movements include local processes such as salt tectonics and regional northwest–southeast compression related to Africa–Eurasia convergence. We suggest that the anomalous movement detected in this work is due to the regional northwest–southeast compression related to Africa–Eurasia convergence imparting an extrusion of the EAB to the west. This research contributes to a better understanding of the geodynamics in the northwest Moroccan Atlantic margin, thereby providing valuable insights for ongoing efforts in oil and gas exploration. Furthermore, it indicates the continued activity of the Agadir fault, which would exhibit a sinistral wrench movement, thus posing a threat to the city of Agadir and its inhabitants. [ABSTRACT FROM AUTHOR]

The paper develops an analytical model based on the force equilibrium for the design of steep slope geosynthetic liner systems to overcome downdrag loads from waste settlement. This analytical model calculates the required tensile stiffness for a high strength/stiffness geotextile (HS-GTX) reinforcement over the GMB to limit the maximum HS-GTX tensile strain to 5% and the maximum GMB strain to 4% on the side slope. The numerical model illustrates the need for reducing the GMB tensile strains for a single GMB liner on a steep landfill slope and confirms that the use of a HS-GTX over the GMB is able to limit the maximum HS-GTX and GMB tensile strains to the acceptable strain levels. The analytical model developed in this paper is a practical tool for preliminary design to limit tensile strains of the HS-GTX and GMB in a steep slope geosynthetic liner system. [ABSTRACT FROM AUTHOR]

Effective winter road maintenance relies on precise road friction estimation. Machine learning (ML) models have shown significant promise in this; however, their inherent complexity makes understanding their inner workings challenging. This paper addresses this issue by conducting a comparative analysis of road friction estimation models using four ML methods, including regression tree, random forest, eXtreme Gradient Boosting (XGBoost), and support vector regression (SVR). We then employ the SHapley Additive exPlanations (SHAP) explainable artificial intelligence (AI) to enhance model interpretability. Our analysis on an Alberta dataset reveals that the XGBoost model performs best with an accuracy of 91.39%. The SHAP analysis illustrates the logical relationships between predictor features and friction within all three tree-based models, but it also uncovers inconsistencies within the SVR model, potentially attributed to insufficient feature interactions. Thus, this paper not only showcase the role of explainable AI in improving the ML interpretability of models for road friction estimation, but also provides practical insights that could improve winter road maintenance decisions. [ABSTRACT FROM AUTHOR]

Moisture-induced damage has been known as a major premature distresses in asphalt pavement. Numerous review papers have been made to provide the progression in study on moisture damage of asphalt pavement. However, mechanical properties of asphalt mixtures used as a parameter for moisture susceptibility evaluation were not reviewed in detail. To make the review of moisture-induced damage in asphalt pavement more comprehensive, this paper reviews research studies on moisture damage of asphalt pavement in view of mechanical properties as a parameter during the past 50 years. These parameters include tensile strength ratio (TSR), cohesion ratio (CR), dynamic modulus ratio (DMR), resilient modulus ratio (RMR), and shear strength ratio (SSR). TSR and CR are only relevant at bottom of asphalt concrete (AC), while SSR can be used to describe moisture damage at different AC depths. DMR and RMR are concentrated on the impact of moisture damage via performance characteristics of asphalt mixtures. [ABSTRACT FROM AUTHOR]

Facility management maintains building service quality through cycles of condition assessments and rehabilitation. Building components, however, differ in their nature, service lives, deterioration patterns, and textual/visual inspection data. This complicates the condition assessment process and subsequent rehabilitation decisions. This paper proposes a smart condition assessment framework that uses different artificial intelligence (AI) techniques that suit the condition data analysis of different building components. The framework has been applied to a dataset of over 2000 maintenance requests for roof and heating, ventilation, and air conditioning (HVAC) systems across a 600-villa portfolio. To address their varying needs, convolutional neural networks were used on images of roof defects, while enhanced data mining was used on textual data of HVAC systems. Accordingly, work packages of deteriorated components were identified, and a 60-day schedule was developed to repair 203 HVAC units. This research shows how AI can assist facility management with respect to condition assessment, rehabilitation planning, and resource allocation. [ABSTRACT FROM AUTHOR]

A flexible, lightweight, and high conductivity current collector is the key element that enables fabrication of a high-performance, flexible lithium-ion battery. Here, we report a thin, lightweight, and flexible lithium-ion battery that uses graphite papers deposited with nano-sized metallic layers as the current collector, LiFePO4 and Li4Ti5O12 as the cathode and anode materials, respectively, and a PE membrane soaked in LiPF6 as the separator. Using thin, flexible graphite paper as a substrate for the current collector instead of a rigid, heavy metal foil enables us to demonstrate an ultra-thin lithium-ion battery (total thickness including encapsulation layers of less than 250 μm) that also features a light weight and high flexibility. [ABSTRACT FROM AUTHOR]

Presents a study that examined the role of papermill sludge in the organic forest carbon cycle of paper products. Prediction on the global production of papermill sludge; Impact of paper production and wastepaper recycling trends on the woody carbon components of sludge; Implications of the organic content and carbon content of sludge for dealing with disposal policy and problems.

Aerated stabilization basins (ASBs) currently account for about one third of the pulp and paper industry's secondary treatment capacity. We surveyed mills with ASBs to analyze design and operating practices. Of the 19 mills that responded, 15 were kraft, reflecting the industry's overall use of ASBs. Biochemical oxygen demand (BOD) and total suspended solids (TSS) loading to the ASBs varied considerably and were factors in biotreatment performance. Problems identified with some ASBs included excessive solids accumulation resulting in the need for frequent dredging, high TSS discharge, and difficulty with nutrient management. Most ASBs have either two or three cells. An important parameter identified for these cells is the benthal settling area. Too small an area results in a higher dredging frequency, with limited nutrient feedback. In general, ASB systems that used the most intensive mixing and aeration in the upstream cells tended to have a smaller benthal settling area, resulting in the need to dredge more frequently. Ideally, some benthal settling should be designed into the upstream cells to allow nutrient feedback where it is needed most. [ABSTRACT FROM AUTHOR]

The road agencies collect and submit weigh-in-motion (WIM) data to the Federal Highway Administration as part of their traffic monitoring program. Therefore, the WIM data should be precise and accurate. One way to evaluate WIM measurement errors is by using the test truck data collected immediately before and after equipment calibration. The limitation of this approach is that the data represent a snapshot in time and may not represent a long-term WIM site performance. This paper presents an approach for estimating WIM system accuracy based on axle load spectra attributes (normalized axle load spectra (NALS) shape factors). This alternative approach allows for characterizing temporal changes in WIM data consistency. The WIM error data collected before and after calibration were related to Class 9 NALS shape factors in the proposed methodology. This paper aims to determine WIM system errors based on axle loading without physically performing WIM equipment performance validation using test trucks. The presented methodology can be used to estimate systematic errors (drift) in the WIM system at any point in time after the equipment calibration. This approach can help highway agencies select optimum timings for routine maintenance and calibration of WIM equipment without compromising its accuracy. The results show that the WIM accuracy for the single axle (SA) and tandem axle (TA) can be estimated with SA and TA NALS shape factors with an acceptable degree of error for bending plate to quartz piezo sensors. Examples are included to demonstrate the application and significance of the developed models. [ABSTRACT FROM AUTHOR]

Bridge infrastructure assets should be planned, designed, constructed, and operated to account for the physical processes that may occur over their service lives. In ice-affected rivers, this includes the interaction of bridge infrastructure with river ice. Advancements in river-ice science and modelling of ice processes in ice-covered rivers have enhanced the abilities of civil/hydrotechnical engineers to plan, design, and construct bridges in and along rivers with seasonal ice covers. In this paper, an overview is presented of ice-related considerations with respect to bridges. The bottom-chord elevation of the bridge superstructure with respect to water and ice levels, pier design to withstand ice forces, the waterway opening for ice passage, ice-induced scour, and research needs are discussed. However, as outlined in the paper, research on ice loads and passage at bridge sites and on hydroclimatic and ice conditions that led to bridge damage and failure remains needed. [ABSTRACT FROM AUTHOR]

Eucalyptus globulus subsp. globulus Labill. (Tasmanian Blue Gum), native to southeast Australia, is a benchmark species for the pulp and paper industry. We genotyped 397 trees from 16 populations of E. globulus representing the native diversity in Australia using 24 microsatellite loci. Eight genetically distinct groups were detected, consistent with genetic groupings detected in previous quantitative and molecular studies. A sample of 29 Portuguese individuals was added to help clarify the origin of the Portuguese landrace. The results suggest a southern and eastern Tasmania origin for the Portuguese landrace. This genetic framework will enable researchers to investigate the provenance of individuals of unknown pedigree and assess the levels of representation of E. globulus natural variation in the Portuguese landrace. [ABSTRACT FROM AUTHOR]

Understanding triggering mechanisms of slope failure is of great importance to the stability analysis and safety warning of waste landfill. This paper presents a centrifuge model test on slope failure induced by elevated gas pressure in wet landfill. The formation process of liquid level and gas pressure in the landfill is simulated by means of liquid and gas injections under a centrifugal acceleration of 66.7 g. The injected liquid contains surfactants, which allow it to generate foam in the waste pores when mixed with the injected gas. The pore gas and liquid pressures under two-phase flow condition are monitored separately to clarify the instability process. It is found that the continuous gas injection makes the pore gas pressure increase to peak values of 83.0 kPa–100.8 kPa, which are higher than the peak liquid pressures of 61.3 kPa–75.6 kPa. The formation of high gas pressure zone is attributed to the low gas permeability, which is affected by high liquid saturation as well as foam generation. The slope failure occurs when the pore gas pressure increases to the peak value and the corresponding shear strength decreases to the critical value. Although the gas injection raises the liquid level, the factor of safety of landfill slope will be overestimated if only considering the effect of liquid pressure. According to the response curves of displacement to gas pressure rise, the critical ratios of gas pressure to earth pressure are determined to be 0.74–0.84, which fall within the range of the prototype landfill. The difference between foam and air on pore pressure distribution is also calculated and discussed. [ABSTRACT FROM AUTHOR]

The Cambrian pre-salt dolomite sequence in the Tarim Basin is a target zone of great strategic significance for hydrocarbon exploration in the basin. Using the results of the interpretation of 3D seismic data from Lunnan and 2D seismic data covering the whole basin, and based on a synthesis of outcrop data, drilling data, well logs, core data, and thin-section data, and the findings from previous studies, this paper studies the characteristics of the facies of the Middle–Lower Cambrian in the platform area in the Tarim Basin, the formation and evolution of platform margins, and the sedimentary characteristics, lithofacies, and paleogeographic characteristics of the Middle–Lower Cambrian series. Based on the types of lithofacies and the seismic facies analysis, the sedimentary facies of the Middle–Lower Cambrian strata can be classified into the five types. From bottom to top, the Middle–Lower Cambrian have experienced several development stages, including the deposition of continental shelf sediments of the Yuertusi Formation, gently sloping non-rimmed platform margin sediments of the Xiaoerbulake Formation, weakly rimmed platform margin sediments of the Wusongger and Shayilike formations, and strongly rimmed platform margin sediments of the Awatage Formation. In each stage, the platform margin shifted further east relative to its location in the previous stage. Based on these results and previous studies, the lithofacies and paleogeography maps of the Middle–Lower Cambrian in the Tarim Basin are modified, and the implications for hydrocarbon exploration in this area are discussed. [ABSTRACT FROM AUTHOR]

In this paper, we study the dynamic properties of spin–orbit coupling (SOC) hyperfine f =1 spinor antiferromagnetic Bose–Einstein condensates with the external magnetic field. The condensate is confined in a toroidal trap and the numerical results are obtained based on the multicomponent Gross–Pitaevskii equation. Our results show that, in the presence of SOC, the spin dynamics for zero magnetic field slows with an increase of radius of the torus. However, this process accelerates when the magnetic field is considered. In addition, in this case, the oscillation behavior is almost consistent with the considered maximum radius. In the absence of SOC, the periodicity of spin dynamics vanishes. We also compare the thermalization time for different magnetic fields and radii, which decreases considerably for nonzero magnetic fields with the increase of radius. Furthermore, our analysis suggests that for stronger magnetic field strength the density structure can be regulated. As a consequence, the condensate recovers from the necklace to an annular-shaped state. [ABSTRACT FROM AUTHOR]

Applications of Bayesian updating commonly treat soil parameters as random variables. A significant issue with this is that soil parameters are highly subjective. Therefore, using traditional parameter-based models, Bayesian analysis starts from a subjective prior and it is unclear how this may influence the overall results of a study. In this paper, Bayesian updating is combined with a data-driven method, known as CRACA (i.e., CReep And Consolidation Analysis), for predicting the settlement of embankments on soft soil. Importantly, the method directly ingests measured oedometer data and, therefore, avoids the subjectivity involved in parameter selection. Because parameters are not used, scaling factors are introduced that account uncertainty associated with the laboratory measurements and the automated interpretation process. These factors have an initial value of unity (returning the prior) and are updated in a Bayesian framework as settlement monitoring data are revealed over time to improve future forecasts. The model was applied to an embankment case history and was shown to result in a rapid improvement in the accuracy and a narrowing of the 95% confidence interval as settlement monitoring data are revealed to the model. [ABSTRACT FROM AUTHOR]

Tolerably mobile subsea foundations are designed to slide on the seabed to accommodate flowline thermal expansion and contraction, and are a potential alternative to conventional (fixed) foundations. During the periodic sliding events that occur during operation, soil berms form at the extremities of the foundation footprint. The size of the berm increases throughout the life-cycle of the foundation, leading to increasing peak sliding resistance. This may hinder mobility of the foundation and overstress the pipeline connections that the foundation is designed to support. Equally, the berms may be relied on to reduce sliding and thus minimize settlement of the foundation, which can also overstress pipeline connections. This paper analyses the mechanism leading to berm accumulation and its mobilisation, also addressing periodic remoulding and reconsolidation of the sediment in the berm. A framework is proposed to predict the accumulation of soil berms and the resulting peak sliding resistance, and is validated by eight centrifuge model tests performed on a kaolin clay and a calcareous silt. [ABSTRACT FROM AUTHOR]

In this paper, we consider higher dimensional charged black holes to study nonperturbative corrected thermodynamics. This correction is dominant when the black hole size decreases due to the Hawking radiation. The nonperturbative correction on the black hole entropy is proportional to the exponential of the original entropy with a negative sign. We calculate some thermodynamics quantities such as the internal Helmholtz free energies, and obtain the effect of the exponential correction. We study the first law of thermodynamics and investigate how it satisfies. We also study the stability of the black hole through specific heat analysis and investigate the possible phase transition. We find a second-order phase transition that is interpreted as the unstable/stable phase transition. Then, we find a first-order phase transition that makes it unstable. Hence, the final stage of the Reissner–Nordström black holes may be an unstable phase, which means that black hole evaporation at the quantum scale. It may be a cause that we never find a black hole in accelerators. [ABSTRACT FROM AUTHOR]

In this paper, we have considered the flat Friedmann-Lemaître-Robertson-Walker (FRW) model in the framework of f(R, ∇R) gravity. We have analyzed the significance of bulk viscosity in the f(R, ∇R) gravity model to study the expansion of the universe. We have considered two bulk viscosity parameterizations and the use of power-law cosmology to constrain the model parameters H0 and q. Using the Bayesian analysis and likelihood function in conjunction with the Markov Chain Monte Carlo method, we obtained the model parameters H 0 = 70. 76732 − 0.00088 + 0.00010 and q = − 0. 6478 − 0.000075 + 0.000091 . The behaviors of energy density, bulk viscous pressure, and the effective equation of the state parameter with redshift are investigated in detail. These features demonstrate that the bulk viscosity is a valid candidate for acquiring the negative pressure needed to effectively drive the expansion of the universe. To check the validity of the f(R, ∇R) model, we also analyze the behavior of energy conditions. The adiabatic squared speed of the sound is used to test the model's stability. The Om(z) diagnostic is used in the model to identify the quintessence and phantom regions. [ABSTRACT FROM AUTHOR]

This paper aims to analyze and describe the geotechnical behavior of a piled raft foundation of a tall building (53 floors, 172.4 m high) through the monitoring of strains in the building's columns and piles, the stresses at the raft–soil interface, and the foundation settlements. Field and laboratory tests were performed, and associated with axisymmetric and three-dimensional finite element analysis to the assessment of the measured data. The monitoring of the pile strains suggests the occurrence of soil expansion, caused by the raft excavation process, up to approximately 6 months after the excavation was completed. The presence of different soil profiles under the raft, with different mechanical properties, affected the distribution of the foundation settlements and the pile loads. Initially, the average pile loads were concentrated in the perimeter elements, but, as the construction of the building evolved, they tended to become more uniform. The effect of the superstructure stiffness caused successive load redistributions in the columns, which contributed to the maintenance of the maximum angular distortion of the building within the allowable values and reduced the load difference between the piles positioned in opposite soil profiles. [ABSTRACT FROM AUTHOR]

This paper develops a hierarchical Bayesian model (HBM) that integrates the physical knowledge and the test data to predict the small-strain shear modulus Gmax for a target sand type. The limited target-specific data are combined with the abundant generic data through a hierarchical structure so that the variability of Gmax within one sand type and across different sand types can be captured. The hyperparameters that characterize the same underlying distribution of physical model parameters across all the sand types are first estimated from the abundant generic data. The model parameters for the new sand type are then updated as the limited site-specific data become available. The approach is illustrated using a generic database and two real examples not covered by the generic database. Multiple possible hierarchical models are compared in terms of model complexity and goodness-of-fit. The results show that the hierarchical modeling of small-strain shear modulus data is reasonable and necessary. The hierarchical model can provide less biased and more accurate predictions of Gmax compared to the commonly used complete pooling model, especially in cases where the site-specific data are quite different from the overall average of the generic database. [ABSTRACT FROM AUTHOR]

Assessing foundation response to cyclic loading is vital when designing transport infrastructure, such as road pavements and rail tracks, as well as offshore, port, and tall tower structures. While detailed guidance is available on characterizing many soil types' cyclic behavior, relatively few studies have been reported on stiff, geologically aged, plastic clays. This paper addresses this gap in knowledge by reporting cyclic loading experiments on three natural stiff UK clays that were deposited and buried between the Jurassic Age and Eocene Epoch before geological unloading to their currently heavily over-consolidated states. High-quality samples taken at relatively shallow depths were reconsolidated to nominally in situ K0 stresses in triaxial and hollow cylinder apparatus before imposing cyclic loading. The completely stable, metastable, or unstable outcomes invoked by different levels of undrained cyclic loading are interpreted within a kinematic yielding framework that is compatible with monotonic control experiments' outcomes. The cyclic limits marking the onset of significant changes in permanent strain accumulation, pore pressure development, and stress–strain hysteresis demonstrate that the weathered Gault clay offers the lowest cyclic resistance. The experiments show that energy considerations provide a promising way of evaluating undrained pore pressure generation and stiffness degradation. They also provide a basis for developing cyclic constitutive models and analysis procedures for cyclic foundation design in stiff, high-OCR, plastic clay strata. [ABSTRACT FROM AUTHOR]

This paper presents the results of field tests performed to investigate the installation effects of pre-bored grouted planted (PGP) pile in deep clayey soil. The variation of horizontal soil displacements, excess pore water pressures and lateral soil pressures was measured in the PGP pile installation process. The test results show that the drilling and grouting process induced large horizontal soil displacements in the soil within a radial distance of 2 d (d is pile diameter), and the maximum horizontal soil displacements induced by the drilling and grouting process were smaller than 15.9 mm when the radial distance reached 4–5 d. Moreover, the horizontal soil displacements decreased along the soil layer depth, as the superficial soil layers were of small deformation modulus and lateral soil pressure. The drilling process brought large excess pore water pressures in the soil when the radial distance was less than 3 d, and the excess pore water pressures induced by the drilling stage were all less than 55 kPa when the radial distance reached 4–6 d. The drilling process also induced some lateral soil pressure increases in the soil within a radial distance of 3 d, while the measured maximum lateral soil pressure increases were smaller than 10.9 kPa when the radial distance increased to 4 d. On the whole, the excess pore water pressures and lateral soil pressure increases induced by the installation of PGP pile were much smaller than that induced by the installation of driven PHC pile. Moreover, the horizontal soil displacements, excess pore water pressures and lateral soil pressure increases induced by the installation of PGP pile all recovered rapidly after the installation of pile, as the cemented soil in the pile hole was in liquid state after the drilling and grouting stage. [ABSTRACT FROM AUTHOR]

The strength and stiffness of a composite rockmass (intact material, defects, joints, bedding, etc.) are primary inputs for the engineering analysis of rock slopes and underground excavations. The Geological Strength Index (GSI) has served rock engineering for three decades as a rockmass assessment system based on the blockiness of the rockmass and discontinuity condition. GSI is used to factor the Hoek–Brown strength envelope for intact rock to represent jointed rockmasses in conventional equivalent-continuum numerical modelling. Modern numerical tools can represent networks of discrete (explicit) structure with assigned discontinuity properties. This provides an opportunity to compare explicit structural modelling with the conventional implicit equivalent-continuum approach. In this paper, explicit structural models are developed using elasto-plastic (constant-strength) constitutive models for intact rock and realistic parametric ranges for explicit structure properties. Explicit model results are compared to equivalent-continuum results, validating the classical implicit approach while also identifying key limitations. Explicit models with post-yield weakening of the intact and structural elements are then developed and compared to post-yield weakening implicit models that use post-yield dilation and empirical relationships between peak and residual GSI. The results provide guidance for practical modelling in strain-weakening rockmasses, including recommendations for post-yield dilation in the traditional implicit approach. [ABSTRACT FROM AUTHOR]

Tack coat is a thin asphalt applied between the existing surface and asphalt overlay during road rehabilitation. Its coverage uniformity is vital in providing adhesive bonding between the two layers in the structure. This paper proposes a novel method for automatic uniformity inspection of tack coat coverage using images collected by drones. In this method, color thresholding is first performed to extract coarse region of the tack coat. Then, the boundaries of the tack coat are detected to refine the tack coat region by masking outliers. Next, the region of interest is processed to extract texture features using gray-level co-occurrence. Finally, the texture features are leveraged to grade the tack coat uniformity level using LightGBM. Experiments were conducted to examine the performance of the method. The resulting accuracy signifies the potential of this method in developing high-efficiency and cost-effective solutions to enhance the current tack coat inspection practice. [ABSTRACT FROM AUTHOR]

In construction, the accurate measurements are important in ensuring the quality of work delivered. Different measuring tools have been developed to help workers conduct accurate measuring. However, they may be subject to manipulation difficulties, such as the need for tap/gesture interaction. This paper proposes a novel eye gaze-aided virtual tape measure framework that provides a hands-free manner for conducting the measurements in construction. This framework consists of three components: data collection for point of interest, sensor calibration, and distance calculation. Its effectiveness is tested by measuring the dimensions of 15 common objects in laboratory and on-site environments and achieves the average absolute and relative errors of 2.4 cm and 4.8%. The absolute errors range from 0.3 to 7.3 cm. A comparison study is conducted to demonstrate its superior performance over iPhone's Measure application. The results illustrate the feasibility and potential of using the framework to enable measures for smart construction. [ABSTRACT FROM AUTHOR]

Maskwio'mi (Mi'kmaw language for "oil made from birch bark") is a traditional topical skin medicine of the Mi'kmaq people of Atlantic Canada and is produced in a torrefaction process by heating birch bark (Betula papyrifera, paper birch) inside a metal container in a fire. The resulting viscous, oily mixture is traditionally mixed with goose fat or bear grease to create a topical salve that is subsequently applied to affected skin areas. When birch bark is exposed to high temperatures, pyrolytic chemical processes produce a complex mixture of pharmacologically active compounds, including potentially harmful side products such as ortho-, meta-, and para-cresol. This study discusses the qualitative and quantitative GC-MS analysis of cresols found in maskwio'mi and the challenges of the complex organic matrix. Using caffeine as an internal standard, ortho-, meta-, and para-cresol in birch bark extract were determined to be in the approximate order of 50–1500 ppm range with 3.24 ± 0.09 × 102 ng mg−1 (324 ppm), 8.7 ± 1.0 × 102 ng mg−1 (87 ppm), and 12.4 ± 1.6 × 102 ng mg−1 (1240 ppm), respectively, and thus suitable by Health Canada and FDA cosmetics regulation standards when the extract is co-formulated in creams to concentrations of 0.1–5 wt.% for topical use. [ABSTRACT FROM AUTHOR]

Presents a study that aimed to determine the levels at which phytosterols are present in Canadian pulp and paper mill effluents (PPME). Description of PPME; Chemicals that form the major fraction of plant sterols in PPME; Processes responsible for the observed removal of plant sterols across the biological wastewater treatment systems.

Cyanobacteria blooms represent a global problem with human health and economic and ecosystem nuisance effects. Until now, we have used arbitrary and sometimes confusing criteria to decide whether we are in the presence of a Cyanobacteria bloom. Through scientometric analysis of studies published between 1953 and 2022, I aimed to identify a threshold value that can be used to quantify Cyanobacteria blooms numerically. I considered several methodological approaches (field, field-experimental, and satellite data) and kinds of environments (coastal, marine, and continental ecosystems). The analysis revealed that 48% of the papers used "cyanobacteria bloom" or similar terms qualitatively without providing or employing a quantitative definition. These papers were focused on other topics related to the ecology of Cyanobacteria (78%), while some others (21%) defined blooms by using visual criteria (scum visualization or water discoloration). Of the other half (52%), a few were mathematical models or review papers (5%), while the rest (65%) defined blooms quantitatively. Of these, most reports (approximately 80%) were from eutrophic inland waters and reported mean values for blooms between 80 000 and 249 000 cells mL−1 or 41 and 69 µg L−1 of chlorophyll-a. Calculations were also carried out for oligotrophic to mesotrophic inland waters and marine-coastal waters, which had fewer reports available in the literature. This is a first attempt to identify a consensual definition based on values reported as blooms in nature, a threshold that can undoubtedly be useful in the future to make possible comparisons among several environments and temporal scales. [ABSTRACT FROM AUTHOR]

Landslides are common across Canada and they pose hazards to human safety, economic activities, and the environment. Robust risk management strategies are necessary for sustainable development. A slope risk management framework has been adopted by the geotechnical community for approximately four decades allowing a systematic, consistent and transparent framework for managing risks. Implementing this framework is associated with uncertainties embedded in our estimates of risk. This paper presents a brief summary of the sources and categories of uncertainty in geotechnical slope engineering and focuses on two topics: (1) estimates of uncertainty in risk calculations and (2) temporal changes in landslide likelihood as a function of weather and steps towards estimating landslide risk changes with climate change. The paper argues that a quantitative risk assessment should not focus on the final risk calculation, but the overall knowledge gained. This allows comprehensive documentation of sources of uncertainty and how they impact geotechnical and risk assessments. Furthermore, the paper outlines approaches to define quantitative correlations between rock fall occurrences and weather, which can be leveraged to estimate changes in rock fall risk with climate change. The paper corresponds to, and expands on, the 2021 Canadian Geotechnical Colloquium. [ABSTRACT FROM AUTHOR]

This paper presents a novel approach for measuring the cost requirements and related values for building information modeling (BIM) adoption using the adaptive analytic hierarchy process approach. The proposed approach considers the importance of each BIM use item in relation to its cost, allowing for prioritization of BIM uses based on their relative value while considering prerequisite relationships and budgetary constraints. The effectiveness of the approach was demonstrated through empirical validation involving a survey of 50 construction industry professionals, and two BIM use prioritization methods (project objective-oriented and value-oriented) were recommended for decision-making under budget constraints. The lessons learned from the empirical case study include the importance of Government's role and the industrial standards in evaluating cost-benefit and promoting for BIM adoption, the different contributions of BIM uses across project phases, and the diverse perceptions of BIM cost requirements among different participants. These lessons are invaluable for countries planning BIM implementation. This paper also demonstrates the development and empirical validation of a novel approach for BIM use adoption under limited budgets, which can assist decision-makers in selecting appropriate BIM use items and estimating their associated costs. [ABSTRACT FROM AUTHOR]

In qualifications-based selection (QBS), consultants are selected according to their competencies rather than price. However, clients are often apprehensive about the subjectivity associated with implementing QBS because non-price criteria are hard to measure. In addition, there is no complete set of all relevant consultant evaluation criteria established. There is also a lack of an automated decision support system for objectively assisting owners in selecting qualified consultants with improved consistency and transparency. In this paper, a comprehensive set of consultant evaluation criteria is identified. Evaluation rules are also established for measuring qualitative criteria, where those rules determine the linguistic performance ratings for the fuzzy TOPSIS model instead of decision-makers, which minimizes subjectivity and increases transparency. The decision support system presented in this paper is flexible, allowing the decision-maker to adjust criteria weights based on the project characteristics and to exclude any non-applicable evaluation rules that may not fit in some projects. [ABSTRACT FROM AUTHOR]

Determining absolute electron impact ionization cross-sections for atoms and molecules, whether through experimental or theoretical means, poses a formidable challenge and is typically limited to a narrow selection of species. In this paper, by using measured cross-sections and polarizability data, it was obtained empirical scaling laws for total single ionization and non-dissociative single ionization cross-section maximum of neutral molecules by collisions with electrons. It is found that the total single ionization cross-sections scale linearly with the target electric static polarizability, while the non-dissociate cross-sections exhibit a saturation effect for large target polarizabilities. This saturation effect is interpreted as the increasing role of fragmentation with polarizability. [ABSTRACT FROM AUTHOR]

In this paper, we consider the formation of vortices in multilayer stacks of Bose–Einstein condensates with tilted dipoles by numerical simulations of the Gross–Pitaevskii equation. Different dependencies of critical rotation frequency (CRF) and optical lattice height, vortex number, and rotation frequency are studied, depending on the direction of the dipole axis and dipole strength. Our results show that the CRF in z = 0 is minimum. When the optical lattice height is gradually increased, the CRF decreases gradually. Reducing of dipole strength in anisotropic dipole–dipole interaction (DDI) favours the formation of vortices, and such decline in isotropic DDI hinders the creation of vortices. The reason for this difference is that the repulsive interaction is favorable and the attractive interaction is disadvantageous for the vortex formation. In addition, we study the first-order correlation function and focus on variation of coherence. For small rotation frequency, the break of coherence occurs earlier in the case of purely repulsive interaction. With an increase in rotation frequency, the coherence concurrently disappears in layer z = 2. Moreover, we also investigate the quenched dynamics, showing that the increase of angular momentum is induced by changing the direction of dipoles and in this process the vortex number remains unchanged. [ABSTRACT FROM AUTHOR]

Climate change (CC) causes extreme meteorological events such as floods, droughts, water scarcity, heat waves, wildfires, and extreme cold. CC may also damage public infrastructures such as drinking water systems (DWSs) and reduce water quality from source to tap. The objective of this review paper is to provide a critical analysis of (1) the impact of CC on the three components of the DWSs: source, treatment, and distribution; (2) the perspectives of DWS employees on CC impacts and adaptation solutions for maintaining water quality; and (3) decision support systems (DSSs) that could be used by DWS employees for CC adaptation. A bibliographic research was conducted using international databases and search engines. The search for scientific articles resulted in the selection of 5234 articles, 78 of which were analyzed in more detail for the elaboration of this scoping review. This review shows that the impacts of CC on water quality are significant, but DWS employees are not enthusiastic about developing adaption measures. This review also shows that DSSs can help DWS employees facilitate the CC adaptation process for the protection of source water, improve water treatment plant operations, and enhance routine management of water quality in the distribution system. Further research is needed to identify strategies that might increase the awareness of and interest in climate change impacts, adaptation, and the use of DSSs among DWS employees. [ABSTRACT FROM AUTHOR]

This note presents the application of the mobilisable strength design (MSD) method to the monitoring results of the multi-propped excavation in the south area of the British Library Euston, constructed in a highly overconsolidated stiff clay deposit. The MSD method is an energy-based approach (a nonlinear finite-element method for a single-degree-of-freedom soil-wall system) introduced to develop a simplified design methodology that satisfies both ultimate and serviceability limit states. Wall displacement predictions based on the MSD method are compared with considerable field monitoring data. The sensitivity of the method to reasonable variations in input parameters is considered. A spreadsheet and python code demonstrating the MSD analysis from this paper are provided in the online supplement alongside details of the mathematical formulation. [ABSTRACT FROM AUTHOR]

In this paper, eight shear tests were carried out utilising a double shear with infilled shear interfaces after determining an appropriate experimental design and modified testing scheme. For this, two rock bolts, 20 and 30 tonnes, were tested with modified double shear testing apparatus at different pretension loads. The infilled test scheme was conducted with 5 mm thick sandy clay infilled shear interfaces. A 40 MPa small aggregate concrete was used for all samples to simulate the host rock. Based on the shear profiles, it was found that all samples followed a three-part failure profile consisting of elastic, strain softening, and failure regions. The results of double shear tests revealed that the 20 tonne rock bolt saw a significant overall decrease of approximately 30% in its failure displacement response as opposed to the 30 tonne samples, which saw a 6% increase. Also, it was concluded that the 30 tonne samples outperformed the 20 tonne rock bolts by up to 30%, irrespective of initial pretension settings. Comparing the physical failure characteristics of the samples found that both the 20 and 30 tonne samples exhibited the same response to increased pretension. As the pretension increased, the angle experienced at the hinge point also increased incrementally. [ABSTRACT FROM AUTHOR]

Resilience is a multidisciplinary concept that deals with rapid response and recovery of a system experiencing a disruption. Despite extensive research on this topic, there is a need to clarify resilience concepts in the context of road freight transportation systems (FTSs) from a three-dimensional perspective (i.e., physical infrastructure, users, and managing organizations) and to identify persistent knowledge gaps concerning the characterization and measurement of FTS resilience vis-à-vis disruptive events. This paper addresses these shortcomings through a systematic review of 149 research studies. The synthesis of findings clarifies inconsistencies associated with the characteristics of FTS resilience and in so doing, establishes a unified framework for measuring FTS resilience through the life cycle of disruptive events. Critical data gaps, methodological shortcomings, and a lack of empirical evidence concerning FTS resilience to disruptive events remain. More robust analytical approaches are required to incorporate interdependencies among FTS dimensions into resilience assessments. [ABSTRACT FROM AUTHOR]

This paper presents an effort to address urgent issues associated with semitruck platooning. The weigh-in-motion data were first examined to determine the characteristics of naturally formed semitruck platoons. A safety-based two-vehicle platoon model was then utilized to determine the critical headways for assessing the safety of semitruck platooning in various driving scenarios. The possibilities for passenger vehicles to cut into semitruck platoons were assessed using actual vehicle headway data. Finally, the potential impacts of semitruck platooning on typical interstate highway pavements were assessed using finite element analysis. Most semitruck platoons consist of two to three vehicles. An optimal platoon gap of 0.94 s was identified for connected and automated semitruck platooning. The potential impacts of truck platooning on concrete pavement were negligible for a platoon gap greater than 0.2 s. The maximum possible impact was less than 4% in terms of the service life reduction for interstate asphalt pavement. [ABSTRACT FROM AUTHOR]

It is crucial to evaluate the consistency in weigh-in-motion (WIM) loading over time and quantify the relative accuracy of axle loads based on axle load spectra (ALS) data for different sensor types. This paper presents the temporal evaluation of the ALS from 51 WIM sites and 128 records available in the long-term pavement performance data. Analysis of ALS data over time shows that for single ALS, there is a significant difference in peak loads between the bending plate, and quartz piezo sensor measurements. Also, 100% of the bending plate 86% of the quartz piezo, and 66% of the piezo cables sites exhibited consistent single axle peak loads after 1 year of calibration event. For tandem ALS, significant differences were observed between loaded peaks of bending plate sensor from both quartz piezo and piezo cable sensors. Also, 83% of the bending plate, 78% of the quartz piezo, and 50% of the piezo cable sites exhibited loaded peaks consistently 1 year after calibration. The results show that calibration frequencies longer than 1 year may be acceptable for the bending plate sensors. However, calibration frequencies of at least 1 year for quartz piezo and less than a year for piezo cable sensors are recommended. Pavement designers and analysts should be aware of the changes in WIM data and calibration frequency over time. [ABSTRACT FROM AUTHOR]

Aim of this paper is to investigate an anisotropic locally rotationally symmetric (LRS) Bianchi type-I space–time in the context of the recently proposed f(Q, T) gravity, where Q is the non-metricity scalar and T is energy–momentum tensor. We have considered f(Q, T) = αQ + βT a linear form, where α and β are model parameters. We have analyzed the exact solution of LRS Bianchi type-I space–time by assuming relation between metric potential A = Bn, where n is arbitrary non-zero real number. To study the anisotropic nature of the dynamical dark energy, we assume that the skewness parameters are time dependent and n ≠ 1. We have constrained to our model by using observational Hubble dataset. Onwards, discussed the physical behavior of cosmological parameters such as energy density, pressure, EoS parameter, deceleration parameter and, Energy conditions. [ABSTRACT FROM AUTHOR]

Integral bridges are built without expansion joints to avoid many of the persistent issues with joint degradation and maintenance problems regularly experienced by traditional bridges. In the absence of expansion joints, the cyclic thermal displacements of the integral bridge would be transferred unmitigated by the joints to the abutment resulting in accentuated soil–structure interactions. Previous studies have mainly focussed on the rotational mode of integral abutment movement while the translational mode of movement and backfill deformations have received much less attention. This paper presents the results of laboratory tests conducted on a semiscale (1:2) physical model, which was designed using dimensional analysis to achieve field stress and strain similarity with a full-scale 1.92 m high-prototype integral abutment. The comparative effects from five tests covering low to high cyclic translation amplitude on backfill surface settlement and heave, and lateral earth pressures behind the abutment were investigated over assumed 120 seasonal cycles. Asymptotic settlement depth of the backfill was obtained in each test. Full passive failure surface was observed when the cyclic translation amplitude of the test exceeded the threshold amplitude. The findings also suggest that the settlement depth seemed to be linked to the development of passive failure surface in the following sense—the asymptotic settlement depth in those tests which developed full passive failure surface would attain the same (ultimate) asymptotic depth; conversely, when the passive failure surface had not or only partially developed in that test, the asymptotic settlement depth was dependent on the cyclic translation amplitude, but it was less than the ultimate observed for full passive failure surface. Lateral earth pressure only stabilized to an asymptotic state for the test with the lowest cyclic translation amplitude during the 120 cycles. Shakedown limit state was observed for this case. At larger cyclic translation amplitudes, the lateral earth pressure did not stabilize but continued to evolve with the elapsed cycles, and shakedown limit state was not observed for these cases. [ABSTRACT FROM AUTHOR]

The shear stress–shear displacement relationship and shear strength parameters of the interface between the pipe and the surrounding soil are important for designing the jacking force. One most commonly used method to measure the shear strength of the pipe–soil interface is the direct shear test. This paper presents the results of a series of direct shear tests conducted in the laboratory on the pipe–soil interfaces for different moisture contents. Simultaneously, digital image correlation is used to supplement the research of the horizontal displacement field of the interface. The results show that the increase of normal stress will makes the interface more prone to strain hardening during the shearing process, and the influence of the change of specimen moisture content on the interface strain characteristics gradually weakens. The shearing process of the specimen mainly involved shearing contraction, and slight shear dilation occurs only when the moisture content is small. We proposed a unified model for describing the shear volumetric change caused by the combined action of moisture content and normal stress. The shear displacement field presents a layered distribution, which is related to the shear displacement corresponding to the shear stress. [ABSTRACT FROM AUTHOR]

The process of icing and the resulting layered ice masses, called aufeis, are caused by the freezing of overflow originating from groundwater or surface water. Aufeis can directly impact infrastructure and property, most commonly through winter ice formation and spring flooding within, against, and on the surface of hydraulic structures and transportation infrastructure. They also represent a safety concern for drivers. This geohazard often needs to be managed proactively and efficiently to mitigate associated risks. This paper provides an overview of the consequences of aufeis in northwestern Canada. A total of 50 existing and novel icing and aufeis mitigation approaches are described and classified. The context of applicability for each approach is identified, considering the source of water, the type of infrastructure, and its role in the formation of aufeis. Finally, future research avenues to support the development or improvement of aufeis risk reduction techniques are presented. [ABSTRACT FROM AUTHOR]

Ice platforms are engineered sheets of floating ice that are designed to support long-term stationary loads, usually related to construction. These loads can include cranes, drill rigs, excavators, girder trucks, and tandem trucks. This paper will discuss general design procedures for ice platforms as well as cases with special considerations such as multiple long-term loads, repetitive long-term loads, objects dropped down onto the ice, loads near large holes in the ice, loads near bridge piers, loads near banks, and loads on access ramps. [ABSTRACT FROM AUTHOR]

The process of icing involves the freezing of overflow layers, on ground or within streams, and results in ice bodies called "aufeis" that are common in most northern landscapes. Knowledge about aufeis is still limited despite the cold region engineering challenge they represent. Understanding the causes of overflow events leading to aufeis development represents a key for the prediction, mitigation, and management of this geohazard and can also support the planning and design of infrastructure in the North. This paper introduces a practical classification for the diverse range of overflow processes that generate aufeis, including under-represented processes, such as the instability of winter streamflow. Importantly, it distinguishes flow conveyance from water supply overflow processes and describes the temporal aspect of icing intensity. Finally, research topics are proposed to improve our understanding of aufeis, including their predictability, the impact of climate change on their occurrence and extent, and stream morphology–aufeis interaction. [ABSTRACT FROM AUTHOR]

This paper presents a method to quantitatively assess the impact of ice-affected hydraulics on hydropower operations using the widely used Hydrologic Engineering Center River Analysis System (HEC-RAS) hydraulic model. The model was used to identify historical periods where downstream river ice growth reduced the net head on a US Army Corps of Engineers dam on the Pend Oreille River in Idaho, USA. The model was used to create curves of projected stage impacts based on border-ice and continuous bank-to-bank ice formation scenarios. The temperature modelling capabilities in HEC-RAS were used to hindcast ice formation periods on the river that were validated with shore-based webcam data. These results provide a framework that can be applied to other rivers with hydropower generation, particularly sites where an open-water HEC-RAS model exists. [ABSTRACT FROM AUTHOR]