Search

The analysis was performed on six commonly used 5.56 x 45 mm projectile types (M193, M855, M855A1, L31A1, M995, and AP45). The projectile's impact velocity (chosen as 900 m/s) was the same in the examination process. This made it possible to assess how the projectile's design has affected its performance against a hard steel target. These evaluations included numerical simulations (Ansys Autodyn) of projectile impacts. Using the available experimental data, the materials in the computational model were first validated. A short description and CAD model of projectiles is also given. Relevant conclusions were reported. [ABSTRACT FROM AUTHOR]

As one of the most widely used personal protective equipment (PPE), body armors play an important role in protecting the human body from the high-velocity impact of bullets or projectiles. The body torso and critical organs of the wear may suffer severe behind-armor blunt trauma (BABT) even though the impactor is stopped by the body armor. A type of novel composite material through incorporating shear stiffening gel (STG) into ethylene-vinyl acetate (EVA) foam is developed and used as buffer layers to reduce BABT. In this paper, the protective performance of body armors composed of fabric bulletproof layers and a buffer layer made of foam material is investigated both experimentally and numerically. The effectiveness of STG-modified EVA in damage relief is verified by ballistic tests. In parallel with the experimental study, numerical simulations are conducted by LS-DYNA® to investigate the dynamic response of each component and capture the key mechanical parameters, which are hardly obtained from field tests. To fully describe the material behavior under the transient impact, the selected constitutive models take the failure and strain rate effect into consideration. A good agreement between the experimental observations and numerical results is achieved to prove the validity of the modelling method. The tests and simulations show that the impact-induced deformation on the human body is significantly reduced by using STG-modified EVA as the buffering material. The improvement of protective performance is attributed to better dynamic properties and more outstanding energy absorption capability of the composite foam. [ABSTRACT FROM AUTHOR]

A series of ballistic experiments were performed to investigate the damage behavior of high velocity reactive material projectiles (RMPs) impacting liquid-filled tanks, and the corresponding hydrodynamic ram (HRAM) was studied in detail. PTFE/Al/W RMPs with steel-like and aluminum-like densities were prepared by a pressing/sintering process. The projectiles impacted a liquid-filled steel tank with front aluminum panel at approximately 1250 m/s. The corresponding cavity evolution characteristics and HRAM pressure were recorded by high-speed camera and pressure acquisition system, and further compared to those of steel and aluminum projectiles. Significantly different from the conical cavity formed by the inert metal projectile, the cavity formed by the RMP appeared as an ellipsoid with a conical front. The RMPs were demonstrated to enhance the radial growth velocity of cavity, the global HRAM pressure amplitude and the front panel damage, indicating the enhanced HRAM and structural damage behavior. Furthermore, combining the impact-induced fragmentation and deflagration characteristics, the cavity evolution of RMPs under the combined effect of kinetic energy impact and chemical energy release was analyzed. The mechanism of enhanced HRAM pressure induced by the RMPs was further revealed based on the theoretical model of the initial impact wave and the impulse analysis. Finally, the linear correlation between the deformation-thickness ratio and the non-dimensional impulse for the front panel was obtained and analyzed. It was determined that the enhanced near-field impulse induced by the RMPs was the dominant reason for the enhanced structural damage behavior. [ABSTRACT FROM AUTHOR]

A terminal ballistic analysis of the effects of 7.62 mm X 51 AP P80 rounds on inclined high-strength armor steel plates is the focus of the presented study. The findings of an instrumented ballistic testing combined with 3D advanced numerical simulations performed using the IMPETUS Afea® software yielded the conclusions. The experimental verification proved that slight differences in the pitch-andyaw angles of a projectile upon an impact caused different damage types to the projectile's core. The residual velocities predicted numerically were close to the experimental values and the calculated core deviations were in satisfactory agreement with the experimental results. An extended matrix of the core deviation angles with combinations of pitch-and-yaw upon impact angles was subsequently built on the basis of the numerical study. The presented experimental and numerical investigation examined thoroughly the influence of the initial pitch and yaw angles on the after-perforation projectile's performance. [ABSTRACT FROM AUTHOR]

The wounding potential of a projectile depends on its kinetic energy. The aim of the study was to investigate the deceleration of non-deforming full metal jacket handgun bullets (FMJ) in gelatine blocks of increasing length. The temporary cavity (TC) was visualized using a SA-X2 Photron camera. 126 test shots in 9 mm nominal calibre were fired under strict temperature control conditions (4°C) at small gelatine blocks ranging from 2 to 12 cm in length. The deposited energy was calculated based on the loss of bullet velocity through high-speed video analysis. The length of the TC was measured, when the TC reached its maximum height. The volume of the TC was approximated by a cylinder. Regression analysis showed a linear correlation between the length of the bullet path and the energy transfer. The constant deceleration of the FMJ bullets in gelatine up to 12 cm bullet path was confirmed across various brands and velocity ranges (270–450 m/s). Higher impact velocities correlated with increased loss of energy in the target medium. The shape of the bullet tip influenced the characteristic of deceleration. The volume of the tubular temporary cavity, derived from high-speed video records, was found to be proportional to the energy transferred. The proposed approach might be a valuable tool in advancing wound ballistics research. • Deceleration of FMJ bullets proportional to bullet path in compact target models. • Higher impact velocities resulted in greater loss of energy in the target medium. • The shape of the bullet tip influenced the characteristic of deceleration. • Proportionality of the temporary cavity to the transferred energy. [ABSTRACT FROM AUTHOR]