Search

The H-bridge MLI has cascaded to addicted cascaded the diode with switches of lower rated power, consumption of power reactive and active. A new system is being developed to increase effectiveness of MLI (multilevel inverter). within the electricity system, to inverter is critical for DC-AC voltage conversion. MLI focuses more on Industry Needs. MLI is typically used to provide high power at high voltage applications. In comparison to inverters flying capacitors and the diode-clamped, it has the fewest components and the voltage level it same number to achieve the voltage balancing capacitors or diodes any voltage clamping. This design incorporates a multilayer inverter with a cascaded H Bridge based on a Boost circuit (BCCHB). The job of the voltage to increase the boost circuit of the multilevel inverter. Boost circuits are essential in an application of wide range, including photovoltaic and the use of fuel cells. ML Inverter with Cascaded H Bridge is a Voltage Controlled Source Inverter with the advantages of being small in size and having an output waveform that is independent of load type. A cascaded H Bridge prototype model based on a boost circuit is validated, and the results simulation has been compared with the result. [ABSTRACT FROM AUTHOR]

Flexible direct current (DC) grids face a serious challenge in terms of rapidly isolating DC faults. A DC circuit breaker is an effective solution for DC fault isolation. To improve the fault-isolation and reclosing capability of flexible DC systems, a new high voltage direct current (HVDC) circuit breaker topology with adaptive reclosing capability is proposed in this paper. The topology of the circuit breaker is a T-shaped structure, which has the ability to break the current in both directions and effectively reduce the cost of components. Meanwhile, after the fault is cleared, the circuit breaker is controlled to inject a voltage signal into the line. Based on this, to prevent the circuit breaker reclosing in the event of a permanent fault from having an impact on the system, a method for fault identification based on Euclidean distance that uses the voltage signal to identify the fault properties is proposed. Finally, the performance of the circuit breaker is simulated and verified by PSCAD/EMTDC simulation software, and compared with the typical existing circuit breakers to verify the effectiveness of the circuit breaker and reclosing scheme. [ABSTRACT FROM AUTHOR]

This paper proposes a ± 535 kV hybrid high voltage direct current (HVDC) circuit breaker. In this paper, the interruption processes of the main branch, transferring branch, and MOV (metal oxide varistors) branch are studied by PSCAD/EMTDC computer simulation. Simulation results indicate that an insulated gate bipolar transistor (IGBT) in the main branch will withstand the highest electrical stress (3305 V/2200 A) and the IGBT in the transferring branch will withstand the highest voltage stress (3327 V). Finally, the ± 535 kV hybrid HVDC circuit breaker prototype is manufactured; the test is carried out. Test results suggest that the ± 535 kV hybrid HVDC circuit breaker prototype developed for the Zhangbei four‐terminal voltage source converter (VSC)‐HVDC project can interrupt a ± 25 kA (high current) within 2.84 ms. The simulation results agreed very well with the actual test results of our novel ± 535 kV hybrid HVDC circuit breaker. The novel ± 535 kV hybrid HVDC circuit breaker functioned exceptionally well in achieving fast short‐circuit current isolation. [ABSTRACT FROM AUTHOR]

DC circuit breaker is the key equipment to deal with the interruption of short-circuit current. Compared with the mechanical switch, the solid circuit breaker and the hybrid circuit breaker using the semiconductor device to interrupt the short-circuit current exhibit superiorities in response duration and arc-less characteristics. Massive power devices controlled by corresponding gate drivers which make the semiconductors-based dc circuit breaker bulky and costly are required to withstand the high dc-bus voltage. In this article, the master−slave concept based modular circuit breaker is proposed to simplify the gate driver topology. Only one single gate driver is required to control highly compact modular submodules consisting of power devices, passive components, and diodes. Moreover, the proposed topology can be easily implemented with high flexibility and low cost. Specifically, the gate control function and voltage equalization for series-connected devices can be realized reliably. The master−slave concept and operation principle of the proposed topology are elaborated and the effectiveness has been demonstrated by both simulation and experimental test. [ABSTRACT FROM AUTHOR]

High-voltage direct current (HVDC) circuit breaker development and deployment strongly depend on the testing process, which ensures that the HVDC circuit breakers will satisfy design requirements. This article presents an HVDC circuit breaker test bench circuit configuration that can provide controllable large output currents to simulate different fault conditions for the current breaking test and high output voltage for the dielectric withstand test. The current breaking test circuit is based on multiple cascaded power converters connected in parallel to provide the necessary output current capability. Each cascaded power converter is composed of multiple cells that are operated by a phase-shifted pulsewidth-modulated signal for greater controllability and higher quality of the output waveform. The dielectric withstand test circuit is a simple high-voltage source with a low power rating that can also be used to charge the test bench and the internal circuitry of the circuit breaker that is to be tested. The proposed test bench ensures that fault conditions can be replicated accurately and offers greater flexibility by being able to test mechanical, semiconductor-based, or hybrid HVDC circuit breakers with different current and voltage ratings on the same hardware without any changes. The idea and the operating principle of the proposed test bench are verified experimentally on a downscaled system that consists of three cascaded power converters connected in parallel with three cells per cascaded power converter and with a total equivalent switching frequency of 92.5 kHz. [ABSTRACT FROM AUTHOR]

To improve the reliability of power supply, reclosing schemes are required after transient faults, which commonly occur in overhead line based high voltage DC (HVDC) systems. However, in the event of permanent faults, the auto-reclosing scheme may cause a severe strike. To avoid the severe impacts caused by permanent faults, the fault type should be discriminated before activating the reclosing scheme. Therefore, an adaptive reclosing scheme based on phase characteristics is proposed in this paper. Firstly, the modulation of a periodic voltage by actively controlling the hybrid DC circuit breaker (DCCB) is introduced. Then, a cascaded π equivalent model and its decoupling algorithm are presented to analyze the frequency-domain characteristics of the measured impedance of the coupled overhead lines. From the frequency-domain characteristics, the frequency of the periodic detecting voltage is determined to analyze the phase features of the measured impedance at primary frequency. The permanent or transient faults can thus be accurately identified by using these different phase characteristics, with negligible influence on the healthy lines. In addition, the proposed scheme is robust to various fault resistances, leading to improved reliability. The effectiveness of the proposed scheme is verified in PSCAD/EMTDC. [ABSTRACT FROM AUTHOR]

Series multi‐break mechanical switch is one of the critical components of high‐voltage hybrid DC circuit breakers. However, due to the existence of distributed capacitance, the voltage distribution between the breaks is not balanced. This paper proposed a voltage sharing configuration method of the mechanical switch of hybrid DC circuit breaker, and carried out the static DC voltage and the transient voltage distribution characteristics tests to verify its effectiveness. Considering the influence of whole structure of the circuit breaker, this paper established the electrostatic field model and circuit simulation model of a typical ±535‐kV hybrid DC circuit breaker. And it analyzed the influence of single break's opening fault, breaking open distance, and the shielding fitting on the voltage distribution characteristics of series six break mechanical switch. According to the simulation results based on the Zhangbei voltage source converter‐based high‐voltage direct current project type test parameters, the parameters design of the voltage sharing components of the mechanical switch are obtained, which can meet the voltage sharing coefficient requirement of 95%. [ABSTRACT FROM AUTHOR]

Long pulse gas lasers utilizing double-discharge circuits are different from the single-short pulse gas lasers in that they do not require all of the desired energy to be deposited into the peaking capacitors prior to ignition of the main gap. Instead, the majority of the energy is held in another capacitor that is then discharged in the form of a longer duration discharge pulse output compared with that of single-short pulse lasers. Extended stability of the discharge is typically achieved by igniting the main gap discharge at higher ignition voltages. Several double-discharge circuit topologies exist in the literature. However, each topology has its own disadvantages primarily centered around the components needed and the resulting complexity. In this article we introduce the application of the new hybrid circuit pulsed power topology as a double-discharge circuit with high ignition voltages. The hybrid circuit pulsed power topology was originally published by the authors of this article in their previous publication titled “A New Hybrid Pulsed Power Circuit Topology for Gas Laser Applications.” The advantage of the hybrid circuit as a double-discharge circuit is that it does not require any special device [e.g., semiconductor opening switch (SOS) diode] and can use commonly available components. [ABSTRACT FROM AUTHOR]

Extraction of the current commutation loop (CCL) inductance is necessary for the overvoltage analysis of power devices. In general, each transient process of a converter corresponds to a specific CCL. However, there is no such single CCL in the full-bridge module in hybrid dc circuit breakers during the turn-off transient. First, this article proposes a coupled inductance model of full-bridge modules. The model has less number of inductance compared to the traditional partial inductance model. Second, this article proposes the extraction method of inductances that can be easily obtained by both simulation and measurement. Moreover, the measured overvoltage waveforms of insulated gate bipolar translators (IGBTs) in the full-bridge module agree with the simulation results. Third, we propose an equivalent circuit of the series full-bridge modules in a 500 kV hybrid circuit breaker based on the proposed coupled inductance model. The mutual inductances among different modules are considered due to the compact structure of the series modules. The measured results show that the overvoltage of the IGBT in the series module could be well-predicted by the proposed equivalent circuit. [ABSTRACT FROM AUTHOR]

Highlights • The proposed method can significantly improve the system operation reliability. • The proposed method is insensitive to fault locations, fault types, etc.. • The proposed method can determine the permanent fault location precisely. • There is no impact on the MTDC grid when the method is performed. Abstract In order to ensure that the healthy lines continue to operate after the line fault, the multi-terminal high voltage direct current (MTDC) grid based on half-bridge modular multilevel converter (HB-MMC) prefers to isolate the fault line using DC circuit breakers (DCCBs). Since most of overhead (OH) line faults are instantaneous faults, after the fault line is isolated, usually the DCCB will reclose with a certain delay to improve system stability. For fear of reclosing to permanent fault, this paper proposes a fault property identification (FPI) method suitable for MTDC grids with hybrid DCCBs (HDCCBs), which can distinguish between instantaneous and permanent faults. The method is based on the characteristic signal injected by the HDCCB with the auxiliary circuit. Besides, once a permanent fault has been determined, the method can also locate the fault position accurately. The effectiveness of the proposed FPI method is verified by extensive simulations in PSCAD/EMTDC platform. [ABSTRACT FROM AUTHOR]

• A CAOC-MPHDCB is proposed by combining with the principle of controllable active oscillation and the MPHDCB based on negative voltage source, which can not only greatly cut down the total cost and operation loss, but also reduce the insulation requirement of commutation circuit. The CAOC only needs an energy storage capacitor to store several kV pre-charge voltage, and can generate a high voltage on a pulse capacitor after several oscillations. Like a NVS, the CAOC can generate a negative voltage on the transfer branch to accelerate the current commutating from the main branch into the transfer branch. In addition, the IGBT full-bridge in the CAOC only needs to withstand the pre-charge voltage with low amplitude at any time. The simulation results verify the effectiveness of CAOC-MPHDCB, and shows its great application prospect in the field of HVDC interruption. The hybrid high voltage DC circuit breaker (HDCB) is widely regarded as the most promising solution to the fault current interruption of VSC-based DC grids. However, because of a large number of power electronic modules connected in series in transfer branch, the cost of existing HDCBs are pretty high, which limiting their large-scale commercial application. In this paper, a novel multi-port hybrid high voltage DC circuit breaker commutated by controllable active oscillation circuit (CAOC-MPHDCB) is proposed. Based on the principle of controllable active oscillation, the proposed CAOC-MPHDCB can realize the reliable commutation and fast interruption of fault current while significantly reducing the total cost and operation loss. In addition, the CAOC-MPHDCB can not only isolate line faults that occur continuously in a short time, but also maintain system ring-network structure after isolating the faulty DC bus. The influencing mechanism of parameters on the performance of CAOC-MPHDCB are analysed in detail, and the selection methods of corresponding parameters are obtained. The simulation results show that the principle of CAOC-MPHDCB is effective and feasible. [ABSTRACT FROM AUTHOR]

• The equivalent discharging circuit of the hybrid cascaded LCC/MMC inverter is simplified into a first-order RL circuit by assuming the firing-advance angle is constant after the fault. • The mathematical fault current expressions of the hybrid cascaded LCC/MMC high voltage direct current system are analyzed. • By changing the inserted sequence of submodules, an active fault current limiting strategy based on the submodule sorting algorithm is proposed. • The proposed active current limiting strategy can cooperate with other current limiting strategies to further suppress the fault current. The hybrid cascaded LCC/MMC high voltage direct current (HC-HVDC) system is a prospective topology that can avoid the commutation failure problem of LCC-HVDC while ensuring bulk power transmission capability. However, the complex topology results in different DC fault characteristics at the receiving end, which brings challenges to fault detection and current limiting technology. As a result, it is of great theoretical importance to investigate the fault characteristics of the HC-HVDC system and propose the corresponding fault current limiting strategy. Firstly, this paper simplifies the equivalent discharging circuit of the hybrid cascaded LCC/MMC inverter into a first-order RL circuit by assuming the firing-advance angle is constant after fault, and proposes the fault current expressions by Laplace transform. Secondly, by changing the insertion sequence of submodules, an active fault current limiting strategy based on the submodule sorting algorithm (SMS-FCL) is proposed, which can accomplish fault current suppression, reactive power and DC voltage support, and energy loss reduction simultaneously. Moreover, the proposed SMS-FCL can cooperate with other FCLs to further suppress the fault current, and the cooperation prerequisites are analyzed. Finally, an LCC-LCC/MMC HVDC system is built in PSCAD/EMTDC to validate the accuracy of the proposed fault current expressions and the effectiveness of the current limiting strategy. [ABSTRACT FROM AUTHOR]

In this paper, ultrahigh-voltage (UHV) SiC devices with hybrid unipolar/bipolar operation are introduced and demonstrated. As the first step of such a device, a merged p-i-n Schottky (MPS) diode with an epitaxial p+-anode layer is proposed to reduce the conduction loss of a bipolar device in the low current region. A “snapback” phenomenon is intensively investigated by analytical modeling, device simulation, and experiment and a design guideline of snapback-free hybrid operating MPS diodes is presented. Using the design guideline, snapback-free MPS diodes are fabricated and forward characteristics are investigated. By using a proper edge termination structure, a UHV SiC MPS diode with breakdown voltage of 11.3 kV is demonstrated. [ABSTRACT FROM AUTHOR]

One of the technical challenges that needs to be addressed for the future of the multi-terminal high voltage direct current (M-HVDC) grid is DC fault isolation. In this regard, HVDC circuit breakers (DCCBs), particularly hybrid circuit breakers (H-DCCBs), are paramount. The H-DCCB, proposed by the ABB, has the potential to ensure a reliable and safer grid operation, mainly due to its millisecond-level current interruption capability and lower on-state losses as compared to electromechanical and solid-state based DCCBs. This paper aims to study and evaluate the operational parameters, e.g., electrical, and thermal stresses on the IGBT valves and energy absorbed by the surge arrestors within H-DCCB during different DC fault scenarios. A comprehensive set of modeling requirements matching with operational conditions are developed. A meshed four-terminal HVDC test bench consisting of twelve H-DCCBs is designed in PSCAD/EMTDC to study the impacts of the M-HVDC grid on the operational parameters of H-DCCB. Thus, the system under study is tested for different current interruption scenarios under a (i) low impedance fault current and (ii) high impedance fault current. Both grid-level and self-level protection strategies are implemented for each type of DC fault. [ABSTRACT FROM AUTHOR]

The ultra-fast switching of power MOSFETs, in about 1 ns, is very challenging. This is largely due to the parasitic inductance that is intrinsic to commercial packages used for both MOSFETs and drivers. Parasitic gate and source inductance not only limit the voltage rise time on the MOSFET internal gate structure but can also cause the gate voltage to oscillate. This paper describes a hybrid approach that substantially reduces the parasitic inductance between the driver and MOSFET gate, as well as between the MOSFET source and its external connection. A flip-chip assembly is used to directly attach a die-form power MOSFET and driver on a PCB. The parasitic inductances are significantly reduced by eliminating bond wires and minimizing lead length. The experimental results demonstrate ultra-fast switching of the power MOSFET with excellent control of the gate-source voltage. [ABSTRACT FROM AUTHOR]

We have developed an integration technology for the single electron transistor (SET)/CMOS hybrid systems. SET and CMOS transistors can be optimized without any possible degradation due to mixing dissimilar devices by adopting just one extra mask step for the separate gate oxidation (SGOX). We have confirmed that discrete devices show ideal characteristics required for the SET/CMOS hybrid systems. An SET shows obvious Coulomb oscillations with a 200-mV period and CMOS transistors show high voltage gain. Based on the hybrid process, new hybrid circuits, called periodic multiband filters, are proposed and successfully implemented. The new filter is designed to perform a filtering operation according to the periodic multiple blocking bands of which a period is originated from the SET. Such a novel function was implemented efficiently with a few transistors by making full use of the periodic nature of SET characteristics. [ABSTRACT FROM AUTHOR]

Given the current evolution of Voltage Source Converters (VSC), Multi-Terminal High Voltage Direct Current (MTDC) grids are now becoming a real possibility. Still, some technical issues have to be addressed. The protection of High Voltage Direct Current (HVDC) grids is the main technical challenge that is slowing down the development of MTDC grids. Hence, this paper focuses on protection systems. Thus, protection devices, fault-clearing strategies and protection system requirements are considered. The main topic of this paper is the review of different types of protection methods for MTDC systems that are shown in the literature. They can be classified depending on the use of local measurements or a communication channel in their operation. The protection systems reviewed in this paper include protection systems based on current measurements, voltage measurement, traveling wave analysis and artificial intelligence. A protection system can employ only one of these methods or a combination of them. Finally, the main characteristics of the reviewed protection algorithms are compared, highlighting the system configuration, the converter technology, the adopted fault-clearing strategy, the implemented circuit breakers and the size of the limiting inductors. From the work presented in this paper, it is concluded that the actual tendency in MTDC protection systems is predominantly full-selective fault-clearing strategies combined with hybrid HVDC circuit breakers in series with limiting inductors. In addition, most protection methods are based on current measurement algorithms and a considerably high number of the reviewed protection systems employ a combination of several methods benefiting from their combined characteristics. • Review of protection systems for multi-terminal HVDC grids. • Classification into local-measurement-based and communication-based methods. • Current-based methods are more usually employed than voltage-based methods. • Combination of half-bridge MMCs and hybrid circuit breakers is predominant. • The preferred system configuration varies between symmetric-monopole and bipole. [ABSTRACT FROM AUTHOR]

• A fault detection scheme is proposed for MTDC by using local transient information. • Classify internal and external fault by tracking pulse count in a specific window. • The concept of protection unit is employed for rapid isolation of faulty part. • Results provide evidence for protection scheme's key role in handling MTDC faults. DC faults render hindrance in the flourishment of multi-terminal flexible high voltage DC (MTDC). The fault current rises rapidly, making a sharp peak, however, under a specific fault instance, isolation of the whole network is an impractical solution. For effective reliability of the whole network, rapid and accurate fault detection and selection of faulty pole is mandatory. A fault detection scheme is proposed in this paper to draw transient current harmonics from initial fault current by utilizing Discrete Fourier transform (DFT). Current harmonics employed the fault detection promptly at the converter stations without communication among the MTDC networks. Additionally, the proposed scheme can discriminate internal from external fault by tracking the number of pulse count in a specific interval of the harmonics of the voltage. In this way, the reliability of the protection scheme enhances and escape from the mal-operation of the circuit breaker. For four terminal MTDC transmission network, the simulations are carried out in PSCAD to authenticate the implementation of the proposed scheme and protection units (PU) are utilized for the isolation of faulty part with the combination of hybrid circuit breaker (HCB). A keen analysis of test results authenticated the ability of the proposed scheme to rapidly detect the faults with high precision, along with efficient classification of the nature of faults. Furthermore, consequential results provide a strong evidence for its key role in handling a multitude of MTDC faults. [ABSTRACT FROM AUTHOR]

This paper presents a piezoelectric (PE) energy harvesting circuit, which integrates a Synchronized Switch Harvesting on Inductor (SSHI) circuit and a diode bridge rectifier. A typical SSHI circuit cannot transfer the power from a PE cantilever into the load when the rectified voltage is higher than a certain voltage. The proposed circuit addresses this problem. It uses the two resonant loops for flipping the capacitor voltage and energy transfer in each half cycle. One resonant loop is typically used for the parallel SSHI scheme, and the other for the series SSHI scheme. The hybrid SSHI circuit using the two resonant loops enables the proposed circuit's output voltage to no longer be limited. The circuit is self-powered and has the capability of starting without the help of an external battery. Eleven simple discrete components prototyped the circuit. The experimental results show that, compared with the full-bridge (FB) circuit, the amount of power harvested from a PE cantilever and the Voltage Range of Interest (VRI) of the proposed circuit is increased by 2.9 times and by 4.4 times, respectively. A power conversion efficiency of 83.2% is achieved. [ABSTRACT FROM AUTHOR]

In the current era, the desire for high boost DC-to-DC converter development has increased. Notably, there has been voltage gain improvement without adding extra power switches, and a large number of passive components have advanced. Magnetically coupled isolated converters are suggested for the higher voltage gain. These converters use large size inductors, and thus the non-isolated traditional boost, Cuk and Sepic converters are modified to increase their gain by adding an extra switch, inductors and capacitors. These converters increase circuit complexity and become bulky. In this paper, we present a hybrid high voltage gain non-isolated single switch converter for photovoltaic applications. The proposed converter connects the standard conventional Cuk and boost converter in parallel for providing continuous current mode operation with the help of a single power switch, which gives less voltage stress on controlled switch and diodes. The proposed hybrid topology uses a single switch with a lower component-count and provides a higher voltage gain than non-isolated traditional converters. The converter circuit mode of operation, operating performance, mathematical derivations and steady-state exploration and circuit parameters design procedures are deliberated in detail. The proposed hybrid converter circuit components, voltage gain and performance, were compared with other topologies in the literature. The MATLAB/Simulink simulation study and microcontroller-based experimental laboratory prototype of 150 W were implemented. The simulation study and experimentation results were confirmed to be a satisfactory agreement with the theoretical analysis. This topology produced non-inverting output in continuous input current mode using a single switch with high voltage gain (≈5.116 gain) with a maximum efficiency of 92.2% under full load. [ABSTRACT FROM AUTHOR]

This paper presents a protection scheme to protect multi-terminal high voltage dc (MTDC) networks for interconnection of renewable energy sources. The proposed scheme detects faults by using the Consecutive Data Window Method (CDWM) and harmonics of the system voltage to avoid maloperation of breakers without communication. Fault location is classified and faulty parts is isolated from the rest of the healthier network by using hybrid circuit breakers (HCBs). Moreover; it also categorises the fault with the help of the voltage drop. The rapid response to isolate the faulty portion in a few milliseconds is primarily considered to enhance the reliability and security of the network. The results of simulations verify the efficient fault detection and isolation for different DC faults and the investigation for the impact of significant parameters of the proposed scheme has been considered. The simulations are performed in PSCAD for four terminal MTDC networks to validate the proposed scheme. The performance is also verified under different fault conditions by using Matlab after computing the data from simulations. [ABSTRACT FROM AUTHOR]