Search

Compared with traditional metal materials, carbon-based materials have the advantages of low density, high conductivity, good chemical stability, etc., and can be used as reliable alternative materials in various fields. Among them, the carbon fiber conductive network constructed by electrospinning technology has the advantages of high porosity, high specific surface area and rich heterogeneous interface. In order to further improve the conductivity and mechanical properties of pure carbon fiber films, tantalum carbide (TaC) nanoparticles were selected as conductive fillers. The crystallization degree, electrical and mechanical properties of electrospun TaC/C nanofibers at different temperatures were investigated. As the carbonization temperature increases, the crystallization degree and electrical conductivity of the sample also increases, while the growth trend of electrical conductivity is markedly slowed. The best mechanical properties of 12.39 MPa was achieved when the carbonization temperature was 1200 °C. Finally, through comprehensive analysis and comparison, it can be concluded that a carbonization temperature of 1200 °C is the optimum. [ABSTRACT FROM AUTHOR]

Oil particle removal, different from the removal of general salt particular matter, has an unusual filtration process in which oil particles will be captured by forming a continuous film on the surface of the filter. Therefore, it is important to investigate the effect of surface property of the filter on the oil particle dynamic filtration process. In this study, three fibrous mats with different surface energies were fabricated from polyacrylonitrile (PAN), polyacrylonitrile/cellulose acetate (PAN/CA), and polyacrylonitrile/polyvinylidene fluoride (PAN/PVDF) solutions by needleless electrospinning. PAN/PVDF fibrous mat presented the lowest surface energy (19. 99 mj/m²), followed by PAN/CA fibrous mat( 29.49 mj/m²) and PAN fibrous mat (40.91 mj/m²). As the oil particle filtration went on, the PAN/PVDF fibrous mat presented both the fastest filtration efficiency decline (4.72% in 10 min) and the fastest filtration resistance increase (543.41 Pa in 10 min). [ABSTRACT FROM AUTHOR]

An alternative magnetic field (AMF)-induced electrospun fibrous thermoresponsive composite actuator showing penetrable remote-control ability with fast response is shown here for the first time. The built-in heater of magnetothermal Fe3O4 nanoparticles in the actuator and the porous structure of the fibrous layer contribute to a fast actuation with a curvature of 0.4 mm−1 in 2 s. The higher loading amount of the Fe3O4 nanoparticles and higher magnetic field strength result in a faster actuation. Interestingly, the composite actuator showed a similar actuation even when it was covered by a piece of Polytetrafluoroethylene (PTFE) film, which shows a penetrable remote-control ability. [ABSTRACT FROM AUTHOR]

Electrospinning is a common method for preparing nanomaterials. Among many electrospinning materials, electrospun carbon nanofibers (CNFs) have become one of the hot research directions for advanced functional materials owing to their good mechanical properties, high surface area, excellent flexibility, physical and chemical stability. Particularly, significant progress has been made in the engineering advancement of electrospinning, electrospun CNFs and their derived reinforced composites to fulfill various applications. This review aims to afford a comprehensive overview of electrospun CNF reinforced composites. Firstly, the different precursors, the correlative properties, and surface modification strategies (e.g. , physical modification and chemical modification) of electrospun CNFs are introduced. Secondly, the preparation methods of reinforced composites based on electrospun CNFs are described in detail. Then, the functional applications of electrospun CNF reinforced composites are discussed. Finally, the challenges and future solutions of electrospun CNF reinforced composites are also prospected. This review is expected to offer a basic but deep understanding of modification strategies to heighten the surface performances of CNFs for the future development of high-performance electrospun CNF reinforced composites in the composite industry, defense, and aerospace applications. [Display omitted] • Electrospun CNF reinforced composites are widly used in engineering materials. • The precursors and modification strategies of electrospun CNFs are detailly reviewed. • Diverse preparation and application of CNF reinforced composites are summarized. • The current challenges of electrospun CNF reinforced composites are discussed. • The future prospects of CNF-based composites in advanced engineering are proposed. [ABSTRACT FROM AUTHOR]

[Display omitted] • The actuator can achieve synergistic movement of deformation and transportation. • Added Fe 3 O 4 NPs provide both magnetism and high-efficient photothermal conversion. • The hydrogel actuator owns high tensile-strength of 4.59 MPa via electrospinning. • The actuator can provide ultrafast deformational speed of 178°/s. • We have explored new bio-inspired systems with two/multi-step synergic actuation. As a soft/wet intelligent material, hydrogel actuators with multiple stimuli-responsiveness have been widely developed. However, it is still greatly difficult for them to integrate bi/multiple responsiveness together for bio-mimetic synergistic actuation. Here, we have explored a high-strength anisotropic bi-layer hydrogel actuator with P(NIPAM-ABP) layer and Fe 3 O 4 /PAN layer via electrospinning technique, which can provide programmable bi-functional synergistic movement. The Fe 3 O 4 /PAN layer can provide magnetic responsive navigation for long-range transportation on account of the magnetism of the Fe 3 O 4 nanoparticles. Furthermore, the ultrahigh photothermal conversion efficiency of the Fe 3 O 4 nanoparticles in the Fe 3 O 4 /PAN layer, can endow the P(NIPAM-ABP) layer with fast remotely-controlled photothermal-responsive deformation. Most importantly, this hydrogel actuator can achieve complex higher-level programmable movements than before based on the synergy of remotely-controlled deformation and the long-range transportation, which can be utilized to design various novel bio-mimetic soft-robots. Last but not least, the introduction of the electrospinning, not only can achieve high strength (4.59 MPa of tensile strength) of this bi-layer hydrogel, but also can provide both ultrafast (178°/s) and programmable complex photothermal-responsiveness, owing to the ultrahigh specific surface area (ultra-thin and porous structure) and excellent orientation of the thermal-responsive P(NIPAM-ABP) nanofibers respectively. This work will provide a general method via electrospinning for anisotropic hydrogel actuator with bi/multiple-functional synergy and will provide a new strategy for smart actuators and other bio-mimetic intelligent materials/systems. [ABSTRACT FROM AUTHOR]