Search

This paper presents the limitations and potential of ATR-FTIR spectroscopy applied to the study of cellulosic textile collections The technique helps to differentiate natural fibres according to the content of lignin, pectin, hemicellulose, and wax, although some problematic issues should be considered. The spectral differences derived from the environmental humidity uptake and the plant composition are reviewed and discussed in the light of new experimental data. Diagnostic bands are proposed that can discriminate between different fibres from different plants. The contribution of ageing is also considered, demonstrating that sometimes aged fibres cannot be reliably recognised. In contrast, the potential of ATR-FTIR spectroscopy to discriminate between natural and modified fibres is discussed and proven. The best results were obtained when microinvasive ATR-FTIR spectroscopy was coupled with SEM observations. The proposed protocol was tested on microsamples of various cellulosic materials from traditional Japanese samurai armours dating from the 16th to the 20th centuries (Morigi Collection, Museo delle Culture, Lugano, Switzerland). The results facilitated a complete characterisation of the materials and demonstrated that the protocol can be used to study a wide variety of cellulosic materials, including both natural and man-modified fibres, and paper. [ABSTRACT FROM AUTHOR]

Most power transformers are oil-immersed transformers for which its insulation system consists of oil and cellulosic solid. The insulation liquid impregnates the solid-covering air spaces, which improves the efficiency of the insulation system. Not only does the oil ensure electrical insulation but it also works as coolants transferring the heat generated during transformer operation to the exterior of the transformer. Throughout normal operation conditions, transformers experience multiple stresses that degrade their insulation. Since the lifetime of oil-immersed transformers is defined mainly by the state of the insulation paper, it is critical to understand the behavior and degradation mechanisms of new insulation systems that try to overcome the drawbacks of mineral oil as well as to improve power transformer performances. The current increased prevalence of the nonlinear loads additionally stresses power transformers, which generates their premature ageing or even failure. Consequently, new materials and assessment methods are required to guarantee the suitable management of power transformer populations. In this Special Issue "Experimental and Numerical Analysis of Thermal Ageing in Power Transformers", four papers have been published. The guest editor also describes briefly some challenges involved beyond the coverage of this Special Issue. [ABSTRACT FROM AUTHOR]

Smart, environmentally friendly alternatives, i.e., frankincense and rice starch, are recommended for usage in modern paper conservation processes during the re-sizing process treatments. Different concentrations of frankincense and rice starch were applied to paper samples before and after ageing. Multiple analysis methods were performed to ensure the effectiveness of these materials. Promising results were found, but at varying degrees according to the type and concentration of the materials. Scanning electron microscopy illustrated that the frankincense particles were completely absorbed into the cell walls after ageing. Results indicated that there was no considerable change in pH before and after treatment or ageing; the best results for decreasing the acidity utilized a treatment with a mixture of frankincense and rice starch in a 2 to 1 ratio (F2S1). Fourier transform infrared spectroscopy illustrated an increased CH2 region and decreased OH stretching as a result of the bonds formed from the starch and crystals formed by frankincense, which agreed with the increased coating and strength of the paper fibers. The total color change values of all the treated samples after ageing were less than 4.5. Frankincense was found to provide strength in supporting wood fibers. [ABSTRACT FROM AUTHOR]

The condition assessment of oil–paper insulation is a vital issue in transformer management. To investigate the effect of moisture content on the accuracy of the prediction model, accelerated ageing experiments were performed with different initial moisture content (IMC) in laboratory condition. Two types of multi-parameter lifetime prediction models, e.g. with and without consideration of IMC, were presented for comparison purpose. The authors found that a better accuracy for its prediction results could be achieved by establishing the prediction models with the consideration of IMC. Besides, models considering IMC have better economic feasibility than that without considering IMC(non-IMC) as its total cost is cheaper according to life cycle cost (LCC) calculations. In addition, failure probability based on the proposed prediction models was also calculated as a direct indicator for evaluating the oil–paper insulation status. [ABSTRACT FROM AUTHOR]

The condition assessment of oil–paper insulation is a vital issue in transformer management. To investigate the effect of moisture content on the accuracy of the prediction model, accelerated ageing experiments were performed with different initial moisture content (IMC) in laboratory condition. Two types of multi‐parameter lifetime prediction models, e.g. with and without consideration of IMC, were presented for comparison purpose. The authors found that a better accuracy for its prediction results could be achieved by establishing the prediction models with the consideration of IMC. Besides, models considering IMC have better economic feasibility than that without considering IMC(non‐IMC) as its total cost is cheaper according to life cycle cost (LCC) calculations. In addition, failure probability based on the proposed prediction models was also calculated as a direct indicator for evaluating the oil–paper insulation status. [ABSTRACT FROM AUTHOR]

Nomex insulation paper has been widely used in mining dry type transformer insulation because of its excellent performance. However, the injection of space charge can affect the electrical properties of the Nomex paper and accelerate the ageing process of the insulation system, which causes the insulation system failure or even breakdown. Therefore, it is of great practical value to study the space charge characteristics of Nomex insulation paper in different hygrothermal ageing conditions. The accelerated hygrothermal ageing tests of Nomex insulation specimens with different initial moisture contents were conducted. The space charge distribution of specimens impregnated by varnish were measured by the pulsed electro‐acoustic method at different ageing stages. Simultaneously, the space charge characteristics during polarising and depolarising phases were deeply analysed. Experimental results show that negative charges accumulate between the varnish‐paper interface in specimens near the anode. The number of negative charges gradually decreases with the increase of ageing degree. Under the influence of humidity, Nomex paper can be hydrolysed, which increases the trap density and trap level. Finally, a large amount of positive and negative charges in aged specimens would result in the distortion of the local electric field, which could decrease the breakdown strength of Nomex insulation specimens and be a threat to transformer insulation. [ABSTRACT FROM AUTHOR]

The AC breakdown properties of Kraft paper, pressboard and the enamel insulation layer in riceoil, peanut oil and corn oil were investigated under both new and agedconditions. The ageing of paper insulators and the enamel insulation layer inoils with the open cup method was carried out at 130 oC for 500 h in an aircirculation oven. The puncture breakdown strength was determined by varying thenumber of layers and thickness of Kraft paper, while various electrode gapdistances were used to measure the surface breakdown strength. Experimentalresults show that the breakdown strength and the tensile strength of paperinsulators impregnated with these vegetable oils are comparable to that inmineral oil, and the surface breakdown strength of paper insulators is slightlyaffected by types of impregnating oils. The ageing significantly reduces boththe breakdown strength and the tensile strength of paper insulators ininvestigated oils. In addition, it was also found that the enamel layer invegetable oils withstood higher puncture breakdown strength than in mineral oil,and the ageing process significantly reduced the puncture breakdown strength ofthe enamel layer. This enamel layer was observed to markedly enhance the surfacebreakdown strength of pressboard. [ABSTRACT FROM AUTHOR]

To investigate the effect of aging on surface discharge of the pressboard on the shielding electrode at the end of bushing, a thermal aging preparation methods of different aging degrees of pressboard samples, surface defect model, and the associated hemisphere are designed and the step‐up method is used for subsequent experimental work. Finally, the partial discharges (PDs) under different degrees of aging are compared and combined with Fourier Transform Infrared spectra and electric field simulation. Results show that the pre‐discharge occurs mainly in the oil gap between the hemispherical electrode edge and the pressboard. The aging of the pressboard exerts no obvious effect on the discharge characteristics in the initial stage of PD; with the development of the discharge, the development of aging of pressboard leads to a higher electric field intensity acting over a greater area, the more intense the discharge, the faster the relative discharge increases and the larger its amplitude. This discharge will cause decomposition of the oil in the pores of the aging pressboard thus generating gas bubbles which will move as discharge develops. When the bubbles reach the surface of the pressboard, the local electric field intensity will increase and the discharge will become more intense. [ABSTRACT FROM AUTHOR]

The oil‐impregnated transformer is an important part of the power system. The ageing degree of the internal oil‐paper insulation determines the service life of the transformer. The low frequency of the frequency domain dielectric spectroscopy can effectively characterise the ageing degree of transformer oil‐paper insulation. For accurately and quantitatively evaluate the aging state of oil‐paper insulation of transformer, the physical process of low‐frequency electrode polarisation is theoretically analysed in this work. Considering the polarisation of the low‐frequency electrode, the theoretical expression of the dielectric response of the equivalent XY model of the transformer is obtained. Meanwhile, to verify the rationality of the theoretical expression, the accelerated thermal ageing test of the oil‐paper insulation samples were carried out under laboratory conditions. The DC conductivity, ion mobility and FDS tests of oil‐paper insulation samples were tested on ageing 5, 10 and 15 days, respectively. The test results were combined with the theoretical expression of the low‐frequency dielectric response. It is found that the difference between the calculated result and the measured result is small. Therefore, the theoretical expression of the transformer equivalent XY model can be applied to calculate the dielectric parameters of the oil‐paper insulation at low‐frequency. [ABSTRACT FROM AUTHOR]

Induction period evaluated from time domain dielectric response of oil‐paper insulation (OPI) contains information related to heat dissipating property of oil. In the present paper, effect of aging sensitive oil properties on the value of induction period is investigated. Three types of dielectric liquids (pure mineral oil, synthetic ester, mixture of synthetic ester, and mineral oil) are considered for the present work. A neural network (NN) is used for modelling the non‐linear relationship between induction period and various oil properties. The trained network is subsequently used to study the influence of various oil properties on induction period. [ABSTRACT FROM AUTHOR]

The service life of a transformer depends on the ageing degree of the internal oil–paper insulation. In order to reliably predict the remaining service life of oil–paper insulation for a single transformer, this study proposes a method based on monitoring the performance degradation data of oil–paper insulation. In this study, the remaining life prediction model of oil–paper insulation is established according to the Wiener stochastic process. The parameters of the model are iteratively updated by using the Bayesian rule and maximum expectation algorithm. The objective of remaining service life prediction of transformer oil–paper insulation is achieved. In the laboratory, multiple groups of oil–paper insulation samples undergo an ageing test at 130°C. Certain amount of performance degradation data is obtained by continuously monitoring the oil–paper insulation. Along with the prediction method of remaining life, the accuracy of the remaining life prediction of transformer oil–impregnated paper is verified when the model parameters are updated. This is a significant guiding factor for predicting the remaining life through the performance degradation data of the continuously operating transformer. [ABSTRACT FROM AUTHOR]

Study of alternate fluids for transformer and their combination with traditional ones is an interesting area of research. The intent of this work is to investigate the thermal ageing performance of ester oils (synthetic and natural), and mixed oil vis‐à‐vis mineral oil. All the samples were thermally stressed at 110, 140, 160, and 185°C for 2 weeks each. Dissolved decay contents in oil and linear thermal expansion coefficients of solid insulation have been studied using ultraviolet visible infrared spectroscopy and dilatometry analysis, respectively, as per ASTM standards. Change in functional groups of the insulation oils with ageing have been understood by Fourier transform infrared spectroscopy analysis. Additionally, diffusion of oil–moisture mixture into paper with ageing and the corresponding effect on dielectric strength of paper has been also examined using ASTM standards. It is observed that the use of synthetic ester (SE) and addition of SE to mineral insulating oil lead to improved performance of oil–paper insulation system with retarding the rate of degradation of the insulation system. [ABSTRACT FROM AUTHOR]

The existing research on furfural analysis mainly focuses on the relationship between the furfural content in oil and the degree of polymerization (DP) of the paper, which are always obtained by accelerated thermal aging at high temperatures. However, the operating temperature of a winding is relatively low, approximately 60°C to 90°C. Thus, the relationship established at high temperature may be not suitable for the operating temperatures. In this research, aging tests of oil‐paper systems at different temperatures (from 100°C to 130°C) were carried out, with the DP, furfural content in oil and furfural content in paper being measured regularly to analyze the effect of temperature variation on the production and diffusion behavior of furfural in oil–paper insulation. The results show that temperature influences the production of furfural, i.e., there is no obvious difference in the amount of furfural produced by paper in the initial aging periods; however, a higher temperature results in more furfural being produced when the DP decreases to values below 600. An obvious diffusion process occurs after furfural is produced in paper in accelerated aging experiments, resulting in most of the furfural content remaining in the cellulose paper in the initial aging period. [ABSTRACT FROM AUTHOR]

The frequency domain dielectric response method has been one of the most effective approaches for condition assessment of an electrical insulation system. The low‐frequency part is more effective for diagnosing the moisture content and aging status of oil‐paper insulation. To facilitate the study of the low‐frequency dielectric spectrum of oil‐paper insulation, a model applicable to the low‐frequency dielectric response of insulation oil is proposed in this study, which is based on the ionic motion of insulation oil. The creation of charge carriers under field test conditions mainly derives from the dissociation of ionic pairs. During testing, ionic motion of insulation oil is jointly affected by thermal diffusion and the electric field; moreover, dissociation and recombination of negative and positive ions also occur. Therefore, the above factors were all considered in the modelling process. The applicability of the model is verified against measured results. For further interpreting the proposed model, the characteristics of the ionic concentration distribution, the relation between ionic distribution and dielectric properties, and the application of the proposed model are analysed. [ABSTRACT FROM AUTHOR]

This study investigated the inhibitory effects of adsorption treatment on the degradation of oil–paper insulation and corrosive sulphur in oil. A thermal ageing experiment at 130°C was conducted using five different adsorbents to adsorb some impurities in oil on the 15th day of a 30 day ageing test, the related characteristics of oil–paper insulation before and after the adsorption treatment were measured and analysed. Meanwhile, a thermal ageing experiment at 150°C was also conducted before using five different adsorbents to adsorb dibenzyl disulphide (DBDS) in oil, energy dispersive X‐ray was used to evaluate the degree of the corrosion of windings. The result indicates that adsorption treatment is an effective method to inhibit the degradation of oil–paper insulation. A molecular sieve, silica gel and activated alumina can effectively improve the performance of oil–paper insulation. By contrast, the antioxidant (2, 6‐di‐tert‐butyl‐p‐cresol) can be also adsorbed by adsorbents, which accelerate the ageing degradation of the insulating oil. On the other hand, the adsorbents can adsorb DBDS in oil, but cannot remove all DBDS. The effect achieved from silica gel is especially significant, which not only effectively improves the performance of oil–paper insulation but also adsorbs DBDS in oil. [ABSTRACT FROM AUTHOR]

Frequency domain spectroscopy (FDS) is being used to assess the insulation condition of oil–paper power transformers. However, it has to date only been implemented on de‐energised transformers, which requires the transformers to be shut down for an extended period and may cause significant costs. To solve this issue, a newly improved monitoring method based on the FDS principle is proposed to implement the dielectric measurement on energised transformers. Moreover, a chirp waveform excitation and its novel processing method are introduced. Compared with the conventional FDS results, dielectric results from the energised insulation system have higher tanδ values because of the increased losses. To further understand the insulation ageing process, the effects of the geometric capacitance are removed from the measured imaginary admittance of the insulation system to enhance the ageing signature. The resulting imaginary admittance is then shown to correlate well with the central time constant in return voltage measurements results. The proposed methods address the issues on techniques used on energised transformers and provide a clue for on‐line FDS diagnostic application. [ABSTRACT FROM AUTHOR]

A post mortem analysis of scrapped transformers provides an opportunity to directly measure the properties of in-service aged paper insulation. Investigations on 10 scrapped 275 kV and 400 kV power transformers were carried out, where Tensile Index (TI) and Low Molecular Weight Acid (LMA) of the paper insulation sampled from various locations were measured. Multiple-layer TI profile demonstrated the effect of oxidized oil on paper ageing which was confirmed by laboratory ageing experiments. It is LMA rather than High Molecular Weight Acid (HMA) that accelerates the paper degradation. LMA acts as the paper ageing accelerator and also as the paper degradation by-product, supporting the view that self-accelerated hydrolysis process is the main paper ageing mechanism. Finally, a generic relationship between LMA in paper and TI of paper was revealed based on both in-service and laboratory ageing data, i.e. the lower the TI of paper, the higher value of LMA in paper is measured. It implies that LMA in oil can be a potential paper ageing indicator pro viding a link between LMA in oil and paper is found. [ABSTRACT FROM AUTHOR]

Utility asset managers and engineers are concerned about the life and reliability of their power transformers which depends on the continued life of the paper insulation. The ageing rate of the paper is affected by water, oxygen and acids. Traditionally, the ageing rate of paper has been studied in sealed vessels however this approach does not allow the possibility to assess the affect of oxygen on paper with different water content. The ageing rate of paper has been studied for dry paper in air (excess oxygen). In these experiments we studied the ageing rate of Kraft and thermally upgraded Kraft paper in medium and high oxygen with varying water content. Furthermore, the oxygen content of the oil in sealed vessels is low which represents only sealed transformers. The ageing rate of the paper has not been determined for free breathing transformers with medium or high oxygen content and for different wetness of paper. In these ageing experiments the water and oxygen content was controlled using a special test rig to compare the ageing rate to previous work and to determine the ageing effect of paper by combining temperature, water content of paper and oxygen content of the oil. We found that the ageing rate of paper with the same water content increased with oxygen content in the oil. Hence, new life curves were developed based on the water content of the paper and the oxygen content of the oil. [ABSTRACT FROM PUBLISHER]

Oxidation ageing experiments on paper insulation and transformer oil have been performed using two different techniques. One is a traditional ageing study wherein degree of polymerization (DP) is measured after conditioning in sealed bottles containing paper submerged in oil, where the partial pressure of oxygen over the oil is varied. Paper is sampled at certain intervals during 8 months and DP-values are measured. The other study was carried out by means of a microcalorimeter; continuously measuring the heat flow from the paper-oil sample. We find that the degradation reaction rate is not linear with oxygen concentration and that the activation energy of oxidation is lower than what has earlier been found for hydrolysis. The microcalorimeter appears to mimic ageing characteristics for oxidation and can potentially be a useful tool for quick ageing investigations. [ABSTRACT FROM AUTHOR]

Acid catalyzed ageing of oil impregnated kraft paper has been studied experimentally. Five different carboxylic acids (formic, acetic, laevulinic, stearic and naphtenic acid) have been added to mineral oil to arrive at a neutralization value of 0,4 mg KOH/g. Thereafter, kraft paper of two different humidities has been allowed to equilibrate with the oil. The results show that the lower the molecular weight of the carboxylic acids is the more is absorbed by the paper. Furthermore, a clear synergy for the paper ageing rates between moisture and the lower molecular weight acids is found, while for the higher molecular weight acids almost no effects were found. It is concluded that present techniques for measuring acidity of oils do not reflect these detailed conditions. It is suggested to introduce a new measuring technique for neutralization value where water rinsing is used to identify the content of low molecular weight, water soluble acids. [ABSTRACT FROM AUTHOR]

Managing a large fleet of ageing assets has become a technical challenge faced by many electricity utilities in developed countries. Asset managers are increasingly interested in techniques that can help extend the useful lifetime of a transformer. Oil regeneration is one of such techniques. In this paper, oil regeneration experiments were performed on a 6.4/0.4 kV retired distribution transformer to investigate the effect of oil regeneration on improving paper conditions. Oil regeneration was conducted in two stages, with the first stage aimed at 'cleaning the oil' and the second stage targeted at 'cleaning the paper'. Oil samples were collected at regular intervals throughout the process and paper samples were obtained from the transformer before and after each oil regeneration stage. It was found that oil regeneration restores oil parameters, including moisture and acidity, similar to those of new oils at the end of stage 1. Analysis of paper samples indicated a reduction in paper moisture at the end of stage 2 by nearly 40%, while low molecular weight acids (LMA) in paper exhibited a reduction by around 30% on average. It is found that the extended oil regeneration period, i.e., stage 2, is necessary to improve the paper condition and hence to reduce the paper ageing rate. [ABSTRACT FROM AUTHOR]