Search

As one of the most widely used personal protective equipment (PPE), body armors play an important role in protecting the human body from the high-velocity impact of bullets or projectiles. The body torso and critical organs of the wear may suffer severe behind-armor blunt trauma (BABT) even though the impactor is stopped by the body armor. A type of novel composite material through incorporating shear stiffening gel (STG) into ethylene-vinyl acetate (EVA) foam is developed and used as buffer layers to reduce BABT. In this paper, the protective performance of body armors composed of fabric bulletproof layers and a buffer layer made of foam material is investigated both experimentally and numerically. The effectiveness of STG-modified EVA in damage relief is verified by ballistic tests. In parallel with the experimental study, numerical simulations are conducted by LS-DYNA® to investigate the dynamic response of each component and capture the key mechanical parameters, which are hardly obtained from field tests. To fully describe the material behavior under the transient impact, the selected constitutive models take the failure and strain rate effect into consideration. A good agreement between the experimental observations and numerical results is achieved to prove the validity of the modelling method. The tests and simulations show that the impact-induced deformation on the human body is significantly reduced by using STG-modified EVA as the buffering material. The improvement of protective performance is attributed to better dynamic properties and more outstanding energy absorption capability of the composite foam. [ABSTRACT FROM AUTHOR]

A methodology is developed based on the coupling of a finite element code with an optimisation module for the design of land vehicle armouring composed of lightweight aluminium alloy and high strength steel plate. Following an experiment/simulation correlation, a numerical model has been built and calibrated considering monolithic plates and then verified considering a bi-metal protection against tungsten carbide projectile mimicking the core of a 7.62x51 AP8 ammunition. In addition, a method is proposed to obtain the vres - vi curve for the full 7.62x51 AP8 bullet from the vres - vi curve obtained from the core only. [ABSTRACT FROM AUTHOR]

As a parameter important ballistic, the research about polygonal and grooved barrels' behavior has not been widely carried out. The pressures, velocities, stresses, deformations, and strains generated by the firing of 9 mm × 19 mm ammunition in weapons with polygonal barrels are analyzed numerically and experimentally, compared with those generated in pistols with grooved barrels. The Finite Element Method with equal boundary and loading conditions was used in both types of guns, specifying the actual materials of the projectile and the barrels. Subsequently, experimental tests were carried out on various weapons with 9 mm ammunitions of 115, 122, and 124 gr. The results show that the 9 mm bullet fired in a polygonal barrel undergoes a maximum deformation towards its exterior of 0.178 mm and interior of 0.158 mm, with stress up to 295.85 MPa. Compared with 0.025 mm maximum external deformation and 0.112 mm internal deformation of 9 mm projectiles fired in a grooved barrel, with stress up to 269.79 MPa. The deformation in the polygonal barrel is in a greater area, but the rifling impression left is less deep, making its identification more difficult. Although there are differences in the stresses and strains obtained, similar velocity and pressure parameters are achieved in the two types of barrels. This has application in the development and standardization of new kinds of barrels and weapons. [ABSTRACT FROM AUTHOR]

Copyright of Journal of Polytechnic is the property of Journal of Polytechnic and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

This research deals with the experimental and numerical investigation of ballistic protection provided by a combination of perforated and base armour plates. A 7.62 mm armour piercing projectile was used during the experimentation to determine the ballistic response of an aluminum base armour plate and a combination of steel perforated and aluminum base armour plate. The armour piercing projectiles were able to penetrate the base armour plate while the combination of perforated and base armour plates was able to stop the penetration of the armour piercing projectile. A finite element method based numerical model was developed to investigate the defeating phenomenon of perforated and base armour plate combination. The brittle fracture caused by the bending of the projectile core due to the asymmetric impact was predicted and the resulting fragments of the projectile were unable to penetrate the base armour plate. Craters were formed on the surface of the base armour plate from the impact of the projectile fragments. The numerical model was able to predict the hole growth and penetration of projectile when only the base armour plate was impacted by the projectile. [ABSTRACT FROM AUTHOR]

This paper presents the results of an investigation of the ballistic limits and failure modes of AA2024-T351 sheets impacted by cubical projectiles. The effect of cube orientation on the ballistic limit and failure modes was considered in detail. Three impact configurations were investigated. Configuration one, two and three considered face, edge or corner impacts correspondingly. The experimental results were complemented with finite element analysis results in order to explain the observations. The lowest ballistic limit (202 m/s) was observed when the cube edge impacted on the target. In the cube face impacts, the ballistic limit was higher (223 m/s), and the highest ballistic limit (254 m/s) was observed for the corner impact. Although the face impact did not have the lowest ballistic limit, this impact configuration resulted in the least amount of projectile energy loss for impacts above the ballistic limit. With the aid of finite element modelling, it was possible to develop a better understanding of the test results and explain that the observed differences in impact response were not just due to a difference in projectile frontal area, but also due to the combination of the localised deformation near the projectile impact point and the resulting global (dishing) deformation. [ABSTRACT FROM AUTHOR]

In this paper, a modified laminated finite-element model based on subcell of unit cell and CDM material model was developed in nonlinear explicit finite-element code to investigate the dynamic response of 2D triaxial braided composite under ballistic impact of projectile. Six subcells, which were considered as laminate with different stacking sequences using solid elements, were employed to represent one unit cell of triaxial braided composites, therefore, the fiber-laying direction of braiding architecture is reproduced. In the prediction of the subcell model, an approximate round conical deformation area forms in the target and the failure modes are mainly longitudinal and transverse cracking due to tension. Compared with the continuum model, the subcell model is capable of analyzing the energy absorption of fiber in each direction. Although the failure modes are similar for both methods, the subcell model is more effective in prediction of impact wave propagation than the continuum model because it describes the fiber arrangement of triaxial braided composites. The developed subcell model will be an effective tool for the design process of carbon/epoxy composite fan casings. [ABSTRACT FROM AUTHOR]

This paper presents the computational-based ballistic limit of laminated metal panels comprised of high strength steel and aluminium alloy Al7075-T6 plate at different thickness combinations to necessitate the weight reduction of existing armour steel plate. The numerical models of monolithic configuration, double-layered configuration and triple-layered configuration were developed using a commercial explicit finite element code and were impacted by 7.62 mm armour piercing projectile at velocity range of 900 to 950 m/s. The ballistic performance of each configuration plate in terms of ballistic limit velocity, penetration process and permanent deformation was quantified and considered. It was found that the monolithic panel of high-strength steel has the best ballistic performance among all panels, yet it has not caused any weight reduction in existing armour plate. As the weight reduction was increased from 20-30%, the double-layered configuration panels became less resistance to ballistic impact where only at 20% and 23.2% of weight reduction panel could stop the 950m/s projectile. The triple-layered configuration panels with similar areal density performed much better where all panels subjected to 20-30% weight reductions successfully stopped the 950 m/s projectile. Thus, triple-layered configurations are interesting option in designing a protective structure without sacrificing the performance in achieving weight reduction. [ABSTRACT FROM AUTHOR]

The ballistic performance of thin aluminium targets and influence thereon of different circumferential fixity conditions were studied both experimentally and by finite element simulations. A pressure gun was employed to carry out the experiments while the numerical simulations were performed on ABAQUS/Explicit finite element code using Johnson–Cook elasto-viscoplastic material model. 1 mm thick 1100-H12 aluminium plates of free span diameter 255 mm were normally impacted by 19 mm diameter ogive and blunt nosed projectiles. The boundary conditions of the plate were varied by varying the region of fixity along its circumference as 100%, 75%, 50% and 25% in experiments and the numerical simulations. Further, simulations were carried out to compare the response of the plates with 50% and 75% continuous fixity with those with two and three symmetrical intermittent regions of 25% fixity respectively. The variation in the boundary condition has been found to have insignificant influence on the failure mode of the target however; it significantly affected the mechanics of target deformation and its energy absorption capacity. The ballistic limit increased with decrease in the region of fixity. It decreased for intermittent fixity in comparison with equivalent continuous fixity. And, it has been found to be higher for the impact with projectile having blunt nose in comparison with the one having ogive nose. [ABSTRACT FROM AUTHOR]

This study aims to investigate the penetration of a projectile into a surrogate human tissue numerically, using Finite Element (FE) simulation. 20% Balistic Gelatin material (BG) is simulated with an elasto-plastic hydrodynamic constitutive law, and then impacted by steel spheres at different velocities. The results from the FE simulations are compared with existing experimental data and other analytical equations from the literature. To our knowledge, this is the first study to investigate a projectile penetration by numerical simulation, and then compare the results with analytical and experimental data from previous studies. This developed model gives encouraging results for further investigations of penetrating impact of projectile in the human body. [ABSTRACT FROM AUTHOR]