Search

High entropy alloys (HEAs) are promising materials for various applications including nuclear reactor environments. Thus, understanding their behavior under irradiation and exposure to different environments is important. Here, two sets of near-equiatomic CoCrCuFeNi thin films grown on either SiO2/Si or Si substrates were irradiated at room temperature with 11.5 MeV Au ions, providing similar behavior to exposure to inert versus corrosion environments. The film grown on SiO2 had relatively minimal change up to peak damage levels above 500 dpa, while the film grown on Si began intermixing at the substrate–film interface at peak doses of 0.1 dpa before transforming into a multi-silicide film at higher doses, all at room temperature with minimal thermal diffusion. The primary mechanism is radiation-enhanced diffusion via the inverse Kirkendall and solute drag effects. The results highlight how composition and environmental exposure affect the stability of HEAs under radiation and give insights into controlling these behaviors.

The influence of radiation-induced (1 MeV energy H+ to ∼0.1 displacements per atom (dpa) at 450 °C), nonequilibrium point defect populations on mass transport is studied with an integrated campaign...

Characterizing oxide nuclear fuels is difficult due to complex fission products, which result from time-evolving system chemistry and extreme operating environments. Here, we report a machine learning-enhanced approach that accelerates the characterization of spent nuclear fuels and improves the accuracy of identifying nanophase fission products and bubbles. We apply this approach to commercial, high-burnup, irradiated light-water reactor fuels, demonstrating relationships between fission product precipitates and gases. We also gain understanding of the fission versus decay pathways of precipitates across the radius of a fuel pellet. An algorithm is provided for quantifying the chemical segregation of the fission products with respect to the high-burnup structure, which enhances our ability to process large amounts of microscopy data, including approaching the atomistic-scale. This may provide a faster route for achieving physics-based fuel performance modeling.

Competing microstructural evolution mechanisms can exist simultaneously when duplex stainless steels are operating for several decades in a high temperature service environment. Such competition between different microstructural evolution pathways can be difficult to ascertain using simple model alloy systems necessitating detailed microstructural analysis of phase transformation mechanisms in complex alloys. Thus, duplex stainless steels with complex but well understood chemistries were used to investigate the relative importance of different heterogeneous nucleation sites – specifically, spinodal decomposition and Cu clustering – on Ni-Si-Mn precipitation during thermal aging. Precipitation of Ni-Si-Mn particles in ferrite-bearing steels during thermal aging and irradiation can greatly change mechanical properties. Using duplex stainless steels with custom-modified compositions along with advanced microstructural characterization and first-passage kinetic Monte Carlo simulations, it is revealed that while the interface between Cr and Fe formed during spinodal decomposition can be a pathway for solute diffusion, it is not a preferred site for Ni-Si-Mn precipitation. Instead, the presence of a higher concentration of Cu leads to the formation of small Cu-rich clusters with high energy interfaces that act as nucleation sites for Ni-Si-Mn particles. These results will inform predictive models for the use of precipitation-hardened alloys for extended operation at high temperatures.

First-Passage Kinetic Monte Carlo (FPKMC) simulations of species migration in duplex stainless steels were performed in order to establish relationships between alloy content, segregation behavior, and the formation of Ni–Si–Mn rich particles in cast duplex stainless steels during thermal aging. The Ni–Si–Mn-rich second phase forms after extended aging at reactor operating temperatures and degrades alloy properties. Simulations of Ni–Si–Mn cluster formation were validated through comparison with experimental results obtained through Atom Probe Tomography (APT) on similar alloy compositions, identifying several trends. First, Cu promotes the formation of Ni–Si–Mn clusters, but only when Ni or Mn prefer segregation to the surface of Cu particles; without the segregation of these species, the critical composition for the clusters to form was not achieved. Second, the width of precipitate-denuded zones near γ/δ interfaces increases with decreasing Cu content. This finding was in strong agreement with APT and Scanning Transmission Electron Microscopy results, further validating our model. Finally, our model predicts that Ni–Si–Mn cluster formation will be the most extensive when the Si:Mn ratio is approximately 1:1 and the least extensive when one of these key elements is less concentrated (Mn ≤ 0.5 at.% or Si ≤ 0.5 at.%). The implications of these results on how to improve alloy properties are discussed.

A novel relationship between noble metal phase particles and fission gas bubble production in used nuclear fuel is described. The majority of Te atoms within noble metal phase undergo radioactive decay to form stable Xe within a few hours after particle formation. This results in the production of clusters of Xe atoms contained within the solid metal matrix exhibiting an equivalent gas bubble pressure approaching 1 GPa. These high pressure bubbles are stabilized by the UO2 within the bulk of the fuel. However, when these bubbles form near the fuel/cladding interface, in combination with local and temporal damage caused by fission recoil, they are capable of overcoming the fracture strength of the UO2 and rupturing catastrophically. The force of the resulting bubble rupture is sufficient to eject noble metal phase particles several microns into the cladding. This proposed mechanism explains the observance of noble metal phase in cladding and is consistent with a host of morphological features found near the fuel/cladding interface.

Pacific Northwest National Laboratory (PNNL) has leveraged focused ion beam capability at their Category II Nuclear Facility to facilitate nuclear materials analysis and experimentation at the micron scale. For this particular study, micron-size specimens of un-irradiated UO2 fuel pellets of various enrichments were prepared and irradiated to a burnup equivalent of 8–3700 MWd/MTU. This represents first of its kind study of used fuel investigations outside of a hot cell facility, dramatically minimizing resource requirements through reduction in scale. Results of this study provide insight into the initial production of noble metal phase particles in used nuclear fuel at extremely low burnup levels.

Herein, the successful use of a focused ion beam/scanning electron microscope to prepare microsamples of radioactive single crystals for X-ray diffraction analysis is reported. This technique was used to extract and analyze crystalline Pu-containing particles as small as 28 µm3from Hanford soil taken from the 216-Z-9 waste crib, which were then crystallographically characterized using single-crystal X-ray diffraction to confirm the cubic structure of PuO2. As a systematic proof of concept, the technique was first tested using UO2crystals milled into cubic shapes with approximate volumes of 4620, 1331, 125, 8 and 1 µm3, in order to empirically determine the crystal size limits for characterization by a laboratory-based diffractometer with a sealed tube Mo or Ag anode X-ray source and a charge-coupled device detector.

Understanding the structural evolution and reduction-oxidation behavior of nuclear fuel and cladding during operation is essential for predicting performance during and after service in light water reactors. Using TEM/STEM imaging of cross-sections of the fuel-cladding oxide interface region of high burnup BWR fuel, fission recoil radiation was demonstrated to not only stabilize the tetragonal phase of ZrO2 at temperatures well below the equilibrium temperature, but also to cause grain growth proportional to the fission recoil radiation damage. The tetragonal phase ZrO2 was exclusively present (no monoclinic phase) only in the region where fission product metal particles were found (∼6 μm depth).

Cast stainless steels are widely used in the primary coolant systems of nuclear power plants because of their high strength, toughness, and corrosion resistance. Mechanical property degradation due to thermal embrittlement of the ferrite phase is of major concern in long-term operations. To investigate the aging-induced loss of fracture resistance in cast stainless steels, static fracture resistance (J-R) testing was performed for three different CF8 stainless steels with significantly different δ-ferrite contents. The materials were thermally aged at 290–400 °C for up to 10,000 h and tested in static fracture at 25–400 °C. It was found that the fracture toughness in high-ferrite materials generally decreased with thermal aging, while the relationship between aging and fracture toughness in low-ferrite materials was complicated, showing non-monotonic variation with the degree of aging. While significant degradation was observed for long-term aged high-ferrite materials, no material tested showed a K0.2mm value less than 100 MPa√m.

We report elemental and isotopic analysis for the noble metal fission product phase found in irradiated nuclear fuel. The noble metal phase was isolated from three commercial irradiated UO2 fuels by chemically dissolving the UO2 fuel matrix, leaving the noble metal phase as the undissolved residue. Macro amounts of this residue were dissolved using a KOH + KNO3 fusion and then chemically separated into individual elements for analysis by mass spectrometry. Though the composition of this phase has been previously reported, this work is the most comprehensive chemical analysis of the isolated noble metal phase to date. We report both elemental and isotopic abundances of the five major components of the noble metal phase (Mo, Tc, Ru, Rh, Pd). In addition, we report a sixth element present in high quantities in this phase, tellurium. Tellurium appears to be an integral component of noble metal particles.

Accurate measurements of 235U enrichment within metallic nuclear fuels are essential for understanding material performance in a neutron irradiation environment, and the origin of secondary phases (e.g. uranium carbides). In this work, we analyse 235U enrichment in matrix and carbide phases in low enriched uranium alloyed with 10 wt% Mo via two chemical imaging modalities-nanoscale secondary ion mass spectrometry (NanoSIMS) and atom probe tomography (APT). Results from NanoSIMS and APT are compared to understand accuracy and utility of both approaches across length scales. NanoSIMS and APT provide consistent results, with no statistically significant difference between nominal enrichment (19.95 ± 0.14 at% 235U) and that measured for metal matrix and carbide inclusions.

Cast austenitic stainless steels (CASS) are excellent alloys because they combine high corrosion resistance with high strength and toughness. However, they are susceptible to embrittlement upon long-term thermal aging at elevated temperatures. Thus, the microstructural evolution pathways during thermal aging need to be understood to predict and potentially prevent embrittlement. Atom probe tomography was used to identify and quantify the microstructural evolution pathways of the δ-ferrite in different CASS alloys aged for up to 10,000 h at temperatures between 290 °C and 400 °C. The four steels – CF8, CF8M, CF3, and CF3M − which vary by Mo and C concentration, each experienced spinodal decomposition of the δ-ferrite, and precipitation of G-phase clusters and Cu clusters attached to the G-phase. There were large differences in the extent of these features due to their Mo and C concentration. Using radial distribution function analysis, the interactions of constituent elements was found to determine the evolution of these features, with Mo and C specifically influencing the movement of Cr, Ni, Si, Mn, and Cu atoms due to their relative miscibility with these elements. The results will help inform predictive models for the use of duplex stainless steels for extended operation at high temperatures.

Thermal aging of ferrite in duplex stainless steels leads to a complex microstructural evolution that can give way to large deleterious changes in mechanical properties. The microstructural evolution mechanisms that happen concurrently are strongly linked to minor changes in composition. By characterizing duplex stainless steels with various compositions over a range of aging conditions, it was revealed that adding a modest amount of Mo to cast austenitic stainless steel (such as changing from grade CF3 to grade CF3M) not only increases the kinetics of spinodal decomposition and Ni-Si-Mn-rich G-phase precipitation, but it also forms a separate Mo-rich phase. At shorter equivalent aging times, Mo segregates from Fe and towards Cr accelerating spinodal decomposition. At longer aging times, Mo enriches in the Ni-Si-Mn clusters before phase separating into an adjoined Mo-rich cluster. These phase changes and precipitation events result in a rather steep drop in fracture and impact toughness. These results will inform the design of similar alloys for use at high temperatures.

Neutron irradiation tests were carried out on 3D-printed SiC derived from binderjet additive manufacturing and chemical vapor infiltration. Irradiation was carried to 2.3 dpa over a temperature range of 400–850 °C. Anisotropy that had been observed in the thermal conductivity of 3D-printed SiC prior to irradiation vanished after irradiation as the irradiation defect thermal resistivity accumulated in the material. No degradation in strength was observed in the material before or after irradiation, at various temperatures, or in different orientations. Electron microscopy of the microstructure after neutron irradiation showed distinct defect morphologies in the heterogenous material, but no evidence for irradiation-induced cracking or degradation in the microstructure was observed.

Mechanical testing and microstructural characterization were performed on short-term thermally aged cast austenitic stainless steels (CASS) to understand the severity and mechanisms of thermal-aging degradation experienced during extended operation of light water reactor (LWR) coolant systems. Four CASS materials–CF3, CF3M, CF8, and CF8M–were thermally aged for 1500 h at 290 °C, 330 °C, 360 °C, and 400 °C. All four alloys experienced insignificant change in strength and ductility properties but a significant reduction in absorbed impact energy. The primary microstructural and compositional changes during thermal aging were spinodal decomposition of the δ-ferrite into α/α′, precipitation of G-phase in the δ-ferrite, segregation of solute to the austenite/ferrite interphase boundary, and growth of M23C6 carbides on the austenite/ferrite interphase boundary. These changes were shown to be highly dependent on chemical composition, particularly the concentration of C and Mo, and aging temperature. The low C, high Mo CF3M alloys experienced the most spinodal decomposition and G-phase precipitation coinciding the largest reduction in impact properties.

We report elemental and isotopic analysis for the noble metal fission product phase found in irradiated nuclear fuel. The noble metal phase was isolated from three commercial irradiated UO

Radiation induced segregation and precipitation phenomena in an in-service boiling water reactor 304 stainless steel component were investigated using directly correlated 3D-atom probe tomography and scanning transmission electron microscopy. Significant quantitative differences in measured segregation at grain boundaries were found between the atom probe and energy dispersive spectroscopy measurements of the exact same locations. In particular, a much stronger Si segregation (~10 atomic% via atom probe versus ~4 atomic% via electron microscopy) and different Cr profile shapes were detected that are critical to models of radiation induced segregation and stress corrosion cracking behavior. These quantitative differences highlight the need for comparative microscopy and critical evaluation of limitations in each analytical method. Elemental segregation to dislocations and conjoined-clusters were also highlighted by atom probe; confirming and expanding upon what has been observed in test reactor neutron and accelerator-based ion irradiations.

Deployment of additively manufactured materials into nuclear energy systems requires investigation of the full range of the unique environmental effects on these materials. Hydrogen isotopes are common gaseous species in nuclear reactors and exhibit ample high mobility in most materials. While hydrogen isotopes mobility in wrought stainless steel is well understood, this property is not thoroughly studied for its additively manufactured variants. In this study, we investigated the deuterium permeation and retention in 316L stainless steel manufactured by laser powder bed fusion. The results showed that the deuterium permeability in the as-built additively manufactured 316L stainless steel (AM SS316L) is greater than that of the reference wrought 316L stainless steel by a factor of 2.8. However, the stress-relieved and solution-annealed AM SS316L samples exhibit lower deuterium permeability in comparison with the as-built condition. Following the solution annealing, the deuterium permeability of AM SS316L is comparable with that of the reference wrought SS316L. Deuterium retention in the as-built AM SS316L is 45% higher than that of the wrought 316L stainless steel and slightly higher than that of the two thermally annealed AM SS316L materials. Transmission electron microscopy and positron annihilation lifetime spectroscopy were used to obtain microstructural information used to determine deuterium permeation and retention behavior in the studied materials.

Fabrication of nuclear reactor components using additive manufacturing (AM) methods is now a practical option since the AM technologies have advanced to allow for building of complex parts with high quality materials. To assess the mechanical performance of printed components in reactor-relevant conditions and to build a property database for the AM 316L stainless steel (SS), mechanical testing and characterization were performed before and after neutron irradiation. Miniature tensile specimens were irradiated at the High Flux Isotope Reactor (HFIR) to 0.2 and 2 displacements per atom (dpa) at 300 and 600°C. The AM 316L SS was tested in the as-built, stress-relieved, and solution-annealed conditions, and the wrought (WT) 316L SS in solution-annealed condition as a reference alloy. The baseline test result showed that the AM 316L SS, regardless of the post-build heat treatment, had higher strength than the WT 316L SS, but similar ductility. Post-irradiation tensile testing was conducted at RT, 300°C, and 500°C for selected irradiation conditions. Neutron irradiation induced significant changes in the mechanical behavior of the AM stainless steels, including both hardening and softening. Although the as-built 316L steel after 300°C irradiation showed necking just after yielding, the overall property changes of the as-printed alloy became less significant after 600°C irradiation. Irradiation-induced ductilization was also observed after the higher temperature irradiation. In general, the strength change was smaller in the relatively stronger as-built and stress-relieved AM SSs than in the solution-annealed AM and WT SSs. These relatively lower strength 316L SSs overall retained higher ductility in the irradiation conditions tested, but the stronger 316L SSs demonstrated a similar level of ductility after the higher temperature (600°C) irradiation. It is a positive assessment for the AM 316L materials that no embrittlement was observed within the test and irradiation conditions of the experiment.

Nuclear reactor environments provide a unique scientific and engineering challenge wherein materials must tolerate prolonged exposure to concurrent irradiation, elevated temperatures, and corrosive media. However, uncontrolled variability in material composition and structure often prohibits truly single-variable experiments that can reveal basic aspects of environmental damage. Magnetron sputtering is used here to provide a more controlled model system for these fundamental studies, yielding reproducible single-crystal Fe and FeCr thin films containing 8 and 18 at.% Cr. Electron microscopy is used to determine the systematic correlations between growth conditions and the resulting film microstructure and surface morphology. It is found that the substrate temperature and applied radio frequency (RF) bias can be tuned to obtain consistent homogeneous and single crystal films with a minimal amount of Ar impurities from the RF bias process. Epitaxial, single-crystal Fe films are obtained on MgO substrates at 500 °C with 10 Watt (W) RF bias deposition. However, when Cr is alloyed with Fe, higher substrate temperatures (600 °C) and applied RF biases (15 W) are required to achieve a similar epitaxial single-crystal FeCr film. Accelerated molecular dynamics simulations reveal that Cr impedes surface transport, explaining the need for higher temperature and bias during the growth of the Cr-bearing films.

Cast austenitic stainless steels (CASSs) have been extensively used for the large components of nuclear reactor primary coolant systems. Since the cast steels inevitably contain degradable metastable phases and replacement of the large coolant system components is impractical, the thermal embrittlement of CASS components has been a serious concern in the extended-term operation of nuclear power plants. This study aimed to systematically measure and analyze the effect of long-term thermal aging on the Charpy impact toughness to provide a comprehensive understanding of thermal degradation behavior and a practical aging model to predict the degree of thermal degradation in the cast stainless steels. The materials tested in the research include eight CASS alloys (two CF3s, one CF3M, three CF8s, and two CF8Ms) and two reference wrought materials (304L and 316L), in which the nominal δ-ferrite content ranges from ~2% to 33%. These stainless steels have been thermally aged at two light water reactor (LWR) temperatures (290 and 330 °C) and at two accelerated-aging temperatures (360 and 400 °C) for up to 30,000 h; these include both under-aged and over-aged conditions relative to the extended service lifetime (80 years). Charpy impact testing was performed for aged and non-aged specimens, and the impact (absorbed) energy parameters were correlated with a new aging parameter (A). Both the reduction of impact fracture toughness and the shift of ductile-brittle transition temperature were strongly dependent on the δ-ferrite content and degree of thermal aging. A linear relationship was found between the increasing rate of the index transition temperature T41J and aging parameter A; base on which an empirical model was proposed for prediction of the transition temperature as a simple function of the aging parameter (A) and δ-ferrite content (F). Finally, the critical aging parameter for embrittlement (AC) was evaluated and compared with the existing δ-ferrite content criteria.

The ability to acquire high-quality spatially-resolved mass spectrometry data is sought in many fields of study, but it often comes with high cost of instrumentation and a high level of expertise required. In addition, techniques highly regarded for isotopic analysis applications such as thermal ionization mass spectrometry (TIMS) do not have the ability to acquire spatially-resolved data. Another drawback is that for radioactive materials, which are often of interest for isotopic analysis in geochemistry and nuclear forensics applications, high-end instruments often have restrictions on radioactivity and non-dispersibility requirements. We have applied the use of a traditional microanalysis tool, the focused ion beam/scanning electron microscope (FIB/SEM), for preparation of radioactive materials either for direct analysis by spatially-resolved instruments such as secondary ion mass spectrometry (SIMS) and laser ablation inductively-coupled mass spectrometry (LA-ICP-MS), or similarly to provide some level of spatial resolution to techniques that do not inherently have that ability such as TIMS or quadrupole inductively coupled plasma mass spectrometry (Q-ICP-MS). We applied this preparation technique to various uranium compounds, which was especially useful for reducing sample sizes and ensuring non-dispersibility to allow for entry into non-radiological or ultra-trace facilities. Our results show how this site-specific preparation can provide spatial context for nominally bulk techniques such as TIMS and Q-ICP-MS. In addition, the analysis of samples extracted from a uranium dioxide fuel pellet via all methods, but especially NanoSIMS and LA-ICP-MS, showed enrichment heterogeneities that are important for nuclear forensics and are of interest for fuel performance.

Spatially resolved analysis of uranium isotopes in small volumes of actinide-bearing materials is critical for a variety of technical disciplines, including earth and planetary sciences, environmental monitoring, bioremediation, and the nuclear fuel cycle. However, achieving sub-nanometer scale spatial resolution for such isotopic analysis is currently a challenge. By using atom probe tomography, a three dimensional nanoscale characterization technique, we demonstrate unprecidented nanoscale mapping of uranium isotopic enrichment with high sensitivity across various microstructural interfaces within small volumes (100 nm3) of depleted and low enriched uranium alloyed with 10 wt % molybdenum with different nominal enrichments of 0.20 and 19.75% 235U respectively. The approach presented here can be applied to study nanoscale variations of isotopic abundances in the broad class of actinide-bearing materials, providing unique insights into their origin and thermo-mechanical processing routes.

The role of interface structure on the trapping of He in Cu–Nb nanocomposites was investigated by comparing He bubble formation in nano-multilayers grown by PVD, nanolaminates fabricated by accumulative roll bonding (ARB), and 3D nanocomposites obtained by high pressure torsion (HPT). All samples were implanted with 1 MeV He ions at room temperature and characterized by cross section transmission electron microscopy (TEM). The critical He concentration leading to bubble formation was determined by correlating the He bubble depth distribution detected by TEM with the implanted He depth profile obtained by SRIM. The critical He dose per unit interfacial area for bubble formation was largest for the PVD multilayers, lower by a factor of ∼1.4 in the HPT nanocomposites annealed at 500 °C, and lower by a factor of ∼4.6 in the ARB nanolaminates relative to the PVD multilayers. The results indicate that the (111)FCC||(110)BCC Kurdjumov-Sachs (KS) interfaces predominant in PVD and annealed HPT samples provide more effective traps than the (112)KS interfaces predominant in ARB nanolaminates; however, the good trapping efficiency and high interface area of 3D HPT structures make them most attractive for applications.

Cu90Ag10 alloys were subjected to severe plastic deformation at temperatures ranging from 25 to 400 °C and strain rates ranging from 0.1 to 6.25 s−1 using high-pressure torsion. The deformed samples were characterized by x-ray diffraction, transmission electron microscopy, and atom-probe tomography. A dynamic competition between shear-induced mixing and thermally activated decomposition led to the self-organization of the Cu–Ag system at length scales varying from a few atomic distances at room temperature to ≈50 nm at 400 °C. Steady-state microstructural length scales were minimally affected by varying the strain rate, although at 400 °C, the grain morphology did depend on strain-rate. Our results show that diffusion below 300 °C is dominated by nonequilibrium vacancies, and by comparison with previous Kinetic Monte Carlo simulations [D. Schwen et al., J. Mater. Res. 28, 2687–2693 (2013)], their concentration could be obtained.

Thermal degradation of cast stainless steels was studied to provide an extensive knowledgebase for the assessment of structural integrity during extended operations of reactor coolant systems. The CF3 and CF8 series cast stainless steels with relatively low (5–12%) δ-ferrite contents were thermally aged at 290–400 °C for up to 10,000 h and tested to measure changes in tensile and impact properties. The aging treatments caused significant reduction of tensile ductility, but only slight softening or negligible strength change. The thermal aging also caused significant reduction of upper shelf energy and large shift of ductile-brittle transition temperature (ΔDBTT). The most influential factor in thermal degradation was ferrite content because of the major degradation mechanism occurring in the phase, while the nitrogen and carbon contents caused only weak effects. An integrated model is being developed to correlate the mechanical property changes with microstructural and compositional parameters.

Bulk nanolayered Cu/Nb composites fabricated by accumulative roll bonding (ARB), leading to a nominal layer thickness of 18 nm, were subjected to large shear deformation by high-pressure torsion at room temperature. The evolution of the microstructure was characterized using X-ray diffraction, transmission electron microscopy and atom probe tomography. At shear strains of the crystallographic texture started to change from the one stabilized by ARB, with a Kurdjumov-Sachs orientation relationship and a dominant {1 1 2}(Cu)parallel to{1 1 2}(Nb) interface plane, toward textures unlike the shear texture of monolithic Cu and Nb. At larger strains, exceeding 10, the initial layered structure was progressively replaced by a three-dimensional Cu-Nb nanocomposite. This structure remained stable with respect to grain size, morphology and global texture from strains of similar to 290 to the largest ones used in this study, 5900. The three-dimensional self-organized nanocomposites comprised biconnected Cu-rich and Nb-rich regions, with a remarkably small coexistence length scale, similar to 10 nm. The results are discussed in the context of the effect of severe plastic deformation and strain path on microstructure and texture stability in highly immiscible alloy systems. (C) 2014 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Metallic uranium is an important material for many applications, especially nuclear energy for low enriched metallic fuel forms and new reactor concepts. Due to the its high electropositivity, production pathways to the metallic form are limited. One of the historically most common synthesis routes involves the heating of a uranium (IV) halide, in this study UF4, with a highly electropositive metal like calcium. This synthesis is referred to as “bomb reduction” due to the temperatures and pressures released by the resulting exothermic reaction. This synthesis route is important for production, but it has also been shown to separate a decay product, thorium, from the parent uranium. This fractionation could be important for purification, but also presents the opportunity for radiochronometric dating of the reduction date. Unfortunately, little characterization has been performed on the products of this reaction. The present study performed bomb reduction on ∼10 g of thorium-doped (2000 ppm) UF4 followed by scanning electron microscopy and energy dispersive spectroscopy. This characterization revealed morphological features of the metal product and slag, the latter of which displayed a wide range of features that indicates a complex reaction in which many variables are involved. Initial characterizations also identified thorium-rich particles, which were extracted and analyzed via transmission electron microscopy and atom probe tomography. These characterizations identified a new thorium-bearing phase, Al9-xFe7+xTh2Si

The critical strain for mixing was determined as a function of precipitate size in two-phase Cu 90 Ag 10 alloys using high-pressure torsion experiments. X-ray diffraction, Z-contrast transmission electron microscopy and atom probe tomography were employed to characterize the mixing behavior. For precipitates ranging from 16 to 131 nm in radius, the critical strain increased linearly with the initial precipitate size, with the proportionality constant at ≈5.2 nm −1 . These results are in agreement with model predictions based on random dislocation glide.

This work was supported as part of the Center for Materials at Irradiation and Mechanical Extremes, an Energy Frontier Research Center funded by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences under Award Number 2008LANL1026. The work was carried out in part in the Frederick Seitz Materials Research Laboratory (FS-MRL) Central Research Facilities, University of Illinois. Atom-probe tomography was performed at the Northwestern University Center for Atom-Probe Tomography (NUCAPT) whose local-electrode atom-probe (LEAP) homograph was purchased and upgraded with funding from NSF-MRI (DMR-0420532) and ONR-DURIP (N00014-0400798, N00014-0610539, N00014-0910781) Grants. Instrumentation at NUCAPT was supported by the Initiative for Sustainability and Energy at Northwestern (ISEN). NUCAPT is a Shared Facility at the Materials Research Center of Northwestern University, supported by the National Science Foundation’s MRSEC program (DMR-1121262). Stimulating discussions with Drs. A. Misra, and J. Carpenter (LANL), and Prof. A. Rollett (CMU) are gratefully acknowledged. We also thank Dr. M. Sardela (FS-MRL, UIUC) for his assistance with XRD characterization and texture measurements.