Search

Infection with hepatitis E virus genotype 3 (HEV-3) is an emerging cause of illness in developed countries. In North America and Europe, HEV-3 has been increasingly detected in swine, and exposure to pigs and pork products is considered the primary source of infection. We have previously demonstrated the prevalence of the HEV-3 genome in commercial pork products in Canada. In this study, we investigated the application of citric acid and acetic acid to inactivate HEV-3 on food and on food contact surfaces. For this purpose, plastic, stainless steel, and pork pâté surfaces were inoculated with HEV-3 and were treated with acetic acid or citric acid at 1, 3, or 5%. The infectivity of posttreatment viral particles was determined by cell culture. A greater than 2-log reduction in viral infectivity was observed on plastic and stainless steel treated with the organic acids, but the treatment was less effective on HEV infectivity on pork pâté (average reductions of 0.47 log citric acid and 0.63 log acetic acid). Therefore, we conclude that citric acid and acetic acid have potential application to control HEV-3 on food contact surfaces but are not suitable for food.

The complex and specific surgical instruments (SI) acquired from loaner companies are provided non-sterile and must be reprocessed before each use. We evaluated the management practices of SI in loaner companies in a high (Australia) and a middle-income (Brazil) country.Seven company managers in Australia and eight in Brazil replied to the self-administrated survey.Failures to meet recommended practices were detected, including standard operating procedure (SOP) provision, minimum delivery time, transport container and decontamination in loaner companies in both countries. Six of seven loaner companies in each country provided SOP for instrument reprocessing (one company in Brazil did not reply). Solicitation of the SI may occur 12 h before need in Brazil, and delivery of the set could be accepted 4 h before surgery in both countries. Transport of SI on stainless steel/aluminium trays was reported by 42.85% and 28.6% of companies in Brazil and Australia, respectively. In Australia, 57.1% of the loaner companies affirmed they performed cleaning only if the SI were visibly dirty. In Brazil, 62.5% of the companies reported they use alcohol to wipe SI.There is a need for standardisation of requirements and process verification improvement in loaner SI reprocessing and management.

We previously reported a novel polymeric surface coating, namely, HaloFilm™ that can immobilize and extend the antimicrobial activity of chlorine on surfaces. In this study, we demonstrated the continuous antiviral efficacy of HaloFilm when applied on stainless steel and cotton gauze as two representative models for non-porous and porous surfaces against severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). Forty-eight hours post HaloFilm application and chlorination and 2 h post the viral challenge, the inoculum titre was reduced by 2.25 ± 0.33 and ≥4.36 ± 0.23 log10 TCID50 on non-porous and porous surfaces, respectively. The half-life of the virus was shorter (13.86 min) on a HaloFilm-coated surface than what has been reported on copper (46.44 min).

The aim of this study was to investigate the interaction of carbide nuclear fuels with steel that is being used as cladding material for nuclear reactors. The specimens prepared from steel EN 1.4988 were consecutively annealed in three uranium carbide (UC) powders, having different carbon contents, at 600 °C for 1000 h. Both Ar and Na were used as bonding elements. The increase in the carbon content of the carburized specimens was determined and evaluated according to the bound and free carbon contents in the UC powders. The migration of free and bound carbon atoms into steel via self-diffusion and over Fe3C formation is interpreted as carburizing. Microhardness measurements and stress-strain tests were used to determine the mechanical properties of crude and carburized steel specimens. Maximum hardness at the contact surface and depth of the carburized zone were determined from the microhardness profiles and discussed depending on the bonding elements and carbon content in the specimens. These variables have a significant impact on the elongation percent, 0.2% yield stress, and tensile stress.

The specific objective of this study was to evaluate the effects of atmospheric pressure plasma (APP) in the treatment of experimental periodontitis in Beagle dogs.The APP jet was diagnosed using optical emission spectroscopy and laser-induced fluorescence spectroscopy. Six Beagles received stainless steel ligatures to establish experimental periodontitis model. The teeth in the control group were subjected to conventional root surface debridement (RSD) and chlorhexidine irrigation. The APP group also started with RSD and was then subjected to plasma irradiation. Clinical analyses including plaque index, modified sulcus bleeding index, pocket depth and attachment loss (AL), as well as cone-beam computed tomography (CBCT) analysis, were performed at baseline, 4th week, 8th week and 12th week after treatment.The results showed that typical reactive oxygen and nitrogen species were found in the full spectrum and the gas temperature of APP was close to room temperature. The highest concentrations of hydroxide and oxygen were obtained at 5 mm away from the nozzle. In both groups, all values in clinical examinations were significantly lower (P0.05) at 12th week after treatment than those at baseline. At the 12th week, the AL in clinical examinations and the bone loss in CBCT images in the APP group were significantly lower than those in the control group (P0.05). The hematoxylin-eosin staining showed more renascent alveolar bone in the APP group than in the control group.These findings suggested that APP has profound potential for use as an adjunct approach for periodontitis treatment.

Staphylococcus aureus is one of the main aetiological agents causing food-borne diseases. Some strains produce enterotoxins responsible for food poisoning. In addition, they can form biofilms on several surfaces such as plastics, glass and stainless steel making it difficult to eliminate them. The present study evaluated, for the first time, the antibacterial and antibiofilm activities of the synthetic compound LMM6 against S. aureus. The minimum inhibitory concentration was 0·97, 1·95 and 1·95 μg ml−1 against S. aureus ATCC 25923, S. aureus 629/94 and S. aureus FRI S-6, respectively. The time-kill curves showed that 96 h treatment with LMM6 reduced approximately 4 log CFU per ml at all tested concentrations. Furthermore, LMM6 reduced S. aureus preformed biofilm by approximately 1 log CFU per cm2. During biofilm formation, a reduction of approximately 4 log CFU per cm2 was observed. LMM6 also reduced biofilm biomass during (~60%) and after biofilm formation (~25 to 45%), as shown by the crystal violet assay. Based on these results, we conclude that LMM6 exhibits antibacterial and antibiofilm activity and may be an innovative synthetic molecule for controlling S. aureus.

In orthodontics, the torque generated forces from the rectangular archwires refine the teeth position. Literature shows only linear deformation in brackets during torqueing. The objective of this study was to evaluate a new phenomenon of tie wings rotation, an angular deformation in Stainless Steel (SS) brackets with SS and Beta-Titanium (β-Ti) archwires at various angles of twist. Maxillary central incisor SS 0.457 mm × 0.635 mm and 0.558 mm × 0.711 mm brackets, SS and β-Ti archwires of 0.431 mm × 0.635 mm and 0.533 mm × 0.635 mm sizes were used. Finite element analysis was performed in various bracket-archwire assemblies for simulated torque. Palatal root torque was applied and the gingival tie wings rotation was measured at selected points, from 5° to 30° angles of twist. The tie wings rotation for 30° twist with SS 0.533 mm × 0.635 mm archwire in 0.558 mm bracket ranged from 1.32° to 2.55° and with SS 0.431 mm × 0.635 mm archwire in 0.457 mm bracket from 0.71° to 1.73°. Similarly, with β-Ti 0.533 mm × 0.635 mm archwire in 0.558 mm bracket and β-Ti 0.431 mm × 0.635 mm archwire in 0.457 mm bracket, the tie wings rotation ranged from 0.73° to 1.38° and 0.39° to 0.93° respectively. The tie wings rotation were present in all the FE models. Higher archwire size, stiffness, and angles of twist showed increased rotation. Thus, clinicians should be aware of this tie wings rotation during torqueing as an additional factor for torque loss.

This study aims to compare the static friction of untreated and fine particle shot peening (FPSP) treated stainless steel and ceramic bracket slots. A total of 60 pieces of stainless steel and 60 pieces of ceramic brackets (Roth prescription, 0.022×0.028 in

Additive manufacturing (AM) has emerged as a disruptive technique within healthcare because of its ability to provide personalized devices; however, printed metal parts still present surface and microstructural defects, which may compromise mechanical and biological interactions. This has made physical and/or chemical postprocessing techniques essential for metal AM devices, although limited fundamental knowledge is available on how alterations in physicochemical properties influence AM biological outcomes. For this purpose, herein, powder bed fusion Ti-6Al-4V samples were postprocessed with three industrially relevant techniques: polishing, passivation, and vibratory finishing. These surfaces were thoroughly characterized in terms of roughness, chemistry, wettability, surface free energy, and surface ζ-potential. A significant increase iniStaphylococcus epidermidis/icolonization was observed on both polished and passivated samples, which was linked to high surface free energy donor γsup-/supvalues in the acid-base, γsupAB/supcomponent. Early osteoblast attachment and proliferation (24 h) were not influenced by these properties, although increased mineralization was observed for both these samples. In contrast, osteoblast differentiation on stainless steel was driven by a combination of roughness and chemistry. Collectively, this study highlights that surface free energy is a key driver between AM surfaces and cell interactions. In particular, while low acid-base components resulted in a desired reduction iniS. epidermidis/icolonization, this was followed by reduced mineralization. Thus, while surface free energy can be used as a guide to AM device development, optimization of bacterial and mammalian cell interactions should be attained through a combination of different postprocessing techniques.

Aqueous hexavalent chromium (Cr(VI)) treatment and chromium resource recovery toward Cr-containing wastes are of significant importance and necessity to both wastewater remediation and resource recovery. Herein, via mild photoreaction conditions with isopropanol (IPA) as an electron donor, a catalyst-free strategy for aqueous Cr(VI) extraction to form an insoluble polyhydroxy Cr(V) complex is developed for the first time. Aqueous Cr(VI) with concentration from 5 to 150 ppm can be efficiently extracted with high selectivity even in the presence of coexisting ions, and the total Cr concentration in residue solution can be as low as 0.5 ppm. The Cr resource could be efficiently recovered as pure Cr

Purpose The aim of this study is to evaluate the levels of chromium (Cr), cobalt (Co), and titanium (Ti) after instrumented fusion for scoliosis. Methods Serum samples were collected at median 2.24 (range 0.1–38.8) years after fusion surgery for scoliosis in 91 individuals, of which 71 had been treated with steel implants and 20 with titanium implants. 91 sex and age-matched non-surgically treated individuals with scoliosis were used as controls. Levels of Cr, Co, and Ti were measured. Results In the 91 surgically treated individuals median levels of Cr were 0.54 µg/l vs 0 µg/l in the 91 controls, p p = 0.19, and for Ti were 0 µg/l vs. 0 µg/l, p In the individuals with steel implants and their corresponding controls median Cr levels were 0.63 µg/l vs. 0.00 µg/l, p p = 0.36. No Ti was detected. In the individuals with titanium implants, median Cr levels were 0 µg/l vs. 0 µg/l in their corresponding controls, p = 0.38. Corresponding results for Co was 0.39 µg/l vs. 0.31 µg/l, p = 0.27 and for Ti 4.31 µg/l vs. 0 µg/l, p In the individuals with steel implants a negative correlation between implant time in situ and levels of Cr was found ($$\rho$$ ρ = − 0.52, p $$\rho$$ ρ = − 0.14, p = 0.23). Ti was not detected. In the individuals with titanium implants, there was no correlation between implant time in situ and levels of Cr ($$\rho$$ ρ = 0.36, p = 0.12), Co ($$\rho$$ ρ = − 0.12, p = 0.60) or Ti ($$\rho$$ ρ = 0.22, p = 0.35). Conclusion The use of stainless steel and titanium implants in spinal fusion surgery is associated with elevated metal ion concentrations several years after surgery.

This study was to investigate the synergistic antibacterial effect and inhibition of biofilm formation of nisin in combination with terpenes (carvacrol, cinnamaldehyde, citral and thymol) against Listeria monocytogenes. The bactericidal ranking of terpenes combined with nisin was carvacrol > cinnamaldehyde, citral > thymol. The minimum inhibitory concentration (MIC) of nisin and carvacrol when used together was determined to be 0·1563 mg ml−1 + 0·0195 mg ml−1 (nisin at MIC/2 + carvacrol at MIC/16). The addition of nisin at MIC/2 + carvacrol at MIC/2 caused more decrease in membrane potential than carvacrol or nisin at MIC individually. The decrease rates of hlyA and plcA gene expressions caused by nisin at MIC/2 + carvacrol at MIC/2 were significantly higher than those caused by carvacrol or nisin at MIC individually (P < 0·05). Nisin combined with carvacrol showed the highest inhibition activity to the formation of L. monocytogenes biofilm on stainless steel and lettuce. The inhibition effect of nisin at MIC/2 + carvacrol at MIC/16 was significantly higher than that of nisin at MIC/2 and carvacrol at MIC/16 (P < 0·05).

Bacterial biofilms contribute to contamination, spoilage, persistence, and hygiene failure in the food industry, but relatively little is known about the behavior of foodborne viruses evolving in the complex communities that make up biofilm. The aim of this study was to evaluate the association between enteric viruses and biofilms on food contact surfaces. Formed biofilms of mono- and multispecies cultures were prepared on glass, stainless steel, and polystyrene coupons and 105 pfu/ml of murine norovirus, rotavirus, and hepatitis A virus were added and incubated for 15 min, 90 min, and 24 h. The data obtained clearly demonstrate that the presence of biofilms generally influences the adhesion of enteric viruses to different surfaces. Many significant increases in attachment rates were observed, particularly with rotavirus whose rate of viral infectious particles increased 7000 times in the presence of Pseudomonas fluorescens on polystyrene after 24 h of incubation and with hepatitis A virus, which seems to have an affinity for the biofilms formed by lactic acid bacteria. Murine norovirus seems to be the least influenced by the presence of biofilms with few significant increases. However, the different factors surrounding this association are unknown and seem to vary according to the viruses, the environmental conditions, and the composition of the biofilm.

Ni-Co-W composite coatings modified by different contents of Co-based alloy powder in the Ni-based alloy with 35 wt.% WC (Ni35WC) were deposited on stainless steel by laser cladding. The influence of compositional and microstructural modification on the wear properties has been comparatively investigated by XRD, SEM, and EDS techniques. It was found that the austenite dendrites in the modified coating adding 50 wt.% Co-based alloy were refined and a lot of Cr23C6 or M23(C, B)6 compounds with fine lamellar feature were formed around austenitic grain boundaries or in the intergranular regions. The contribution of element Co to the modification of Ni35WC coating is that it cannot only promote the formation of more hard compounds to refine austenite grains, but also refine the size of precipitates, and change the phase type of eutectic structure as a result of disappeared Cr boride brittle phases. A noticeable improvement in wear resistance is obtained in the Ni35WC coating with 50 wt.% Co-based alloy, which makes the wear rate decreased by about 53 % and 30% by comparison to that of the substrate and the Ni35WC coating, respectively. It is suggested that the improvement is closely related to the composite coating being strengthened owing to the increase of coating hardness, formation of a fine-grained microstructure caused by Co, and fine hard precipitate phases in the eutectic structure.

Objectives To compare between 3 archwires (AWs) for leveling curve of Spee (COS) in terms of efficacy of reduction, external apical root resorption (EARR), pain experienced, and the lower arch dimensional changes during COS leveling. Trial design Randomized clinical trial. Setting Jordan University of Science and Technology Postgraduate dental clinics. Material and methods Fifty-three subjects with COS > 5 mm were included in this study. The subjects were randomly divided into three groups based on the AW used: group 1, 0.017 × 0.025-inch stainless-steel (SS) AW; group 2, 0.019 × 0.025-inch SS AW; and group 3, 0.021 × 0.025-inch β-titanium (TMA) AW. The intervention was randomly allocated using the permuted random block size of 3 with a 1:1:1 allocation ratio. In the three groups, a 5-mm depth reverse COS was placed in the AWs. The following time points were defined for COS assessment: T1, before interventional leveling AW placement; and T2–T7, 1–6 months after interventional leveling AW placement. Records consisted of dental study models and periapical (PA) radiographs. Pain scores were recorded using visual analogue scale. Patients were followed up on a monthly basis until COS Main outcome measures COS depth reduction, lower incisors’ EARR, pain scores, and arch dimensional changes. Results An overall reduction of 3.82 mm, 4.47 mm, and 3.85 mm of the depth of COS was achieved in groups 1, 2, and 3, respectively. The mean differences of 0.65 mm between groups 1 and 2 and 0.62 mm between groups 2 and 3 were significant at P P > 0.05). Higher pain scores were reported by group 2 subjects during the first 24 h. Arch length and width increased significantly in groups 2 and 3 (P Conclusions All investigated AWs were effective in leveling COS with minimal lower incisors’ EARR ( Clinical relevance The 3 investigated leveling AWs were effective for the leveling COS and at the same time safe on the roots of the lower anterior teeth.

Thermal spray coating is an industrial process in which molten metal is sprayed at high velocity onto a surface as a protective coating. An automated electric arc wire thermal spray coating aerosol generator and inhalation exposure system was developed to simulate an occupational exposure and, using this system, male Sprague-Dawley rats were exposed to stainless steel PMET720 aerosols at 25 mg/msup3/sup × 4 h/day × 9 day. Lung injury, inflammation, and cytokine alteration were determined. Resolution was assessed by evaluating these parameters at 1, 7, 14 and 28 d after exposure. The aerosols generated were also collected and characterized. Macrophages were exposed in vitro over a wide dose range (0-200 µg/ml) to determine cytotoxicity and to screen for known mechanisms of toxicity. Welding fumes were used as comparative particulate controls. In vivo lung damage, inflammation and alteration in cytokines were observed 1 day post exposure and this response resolved by day 7. Alveolar macrophages retained the particulates even after 28 day post-exposure. In line with the pulmonary toxicity findings, in vitro cytotoxicity and membrane damage in macrophages were observed only at the higher doses. Electron paramagnetic resonance showed in an acellular environment the particulate generated free radicals and a dose-dependent increase in intracellular oxidative stress and NF-kB/AP-1 activity was observed. PMET720 particles were internalized via clathrin and caveolar mediated endocytosis as well as actin-dependent pinocytosis/phagocytosis. The results suggest that compared to stainless steel welding fumes, the PMET 720 aerosols were not as overtly toxic, and the animals recovered from the acute pulmonary injury by 7 days.

Cerclage wiring may be used for fracture fixation or osteotomy stabilization in revision arthroplasty. There is a lack of evidence regarding the potential risk of bacterial colonization for the different types of cerclages. The objective of our research is to study the adhesion and biofilm formation of S. epidermidis, S. aureus, and P. aeruginosa on two different cerclage cable models, comparing a polymer cable and a stainless steel metal cable. A two-cm cerclage piece of each material was submerged in 2 mL of tryptic soy broth (TSB) inoculated with 10 μL of a 0.5 McFarland bacterial culture, and incubated at 37°C during 2 h for adhesion and 48 h for biofilm formation. The cerclages were washed with 1xPBS and sonicated in a new culture medium. Aliquots of several dilutions of each sonicated culture were spread in TSB agar and incubated at 37°C for 24 h. The number of colonies was counted. The colony-forming units per ml (CFU/mL) and the percentage of reduction were calculated. Experiments were triplicated. For P. aeruginosa, a statistically significant reduction in biofilm formation was found on the polymer cerclage cable, compared to the metal cerclage cable. Reductions of 59% and 88%, after 2 h and 48 h, respectively, were observed. For S. epidermis and S. aureus, there was a trend towards lower bacterial adhesion and biofilm formation for the polymer cerclage cable. In summary, these results demonstrate that the braided polymer cerclage cable may be less prone to bacterial adherence and biofilm formation compared to the braided metal cerclage cable.

Biofilm is a microbiome complex comprising different bacterial colonies that typically adhere to device surfaces in water, which causes serious medical issues such as indwelling infections and outbreaks. Here, we developed a non-nanoparticle, flexible anti-biofilm hygiene coating consisting of lithocholic acid (LCA), zinc pyrithione (Zn), and cinnamaldehyde (Cn) (named as LCA-Zn-Cn) that largely prevents the bacteria adhesion to various water device surfaces such as stainless steel and glass through a synergistic mechanism. The existing chelated groups on LCA and Cn attract plenty of bacteria via hydrophobic interaction. Both the bactericidal reaction by grafting biocidal groups from both LCA and Cn and the bacteriostatic reaction by inhibiting cell division via zinc ions (Zn) lead to a largely improved bacteria/biofilm prevention. The antibacterial performance was assessed by using the JIS Z 2801/ISO 22196 method. The designed LCA-Zn-Cn coating displayed log

Purpose To assess clinical and safety outcomes associated with different rod materials and diameters in adult spinal deformity (ASD) surgery. Methods A systematic literature review and meta-analysis evaluated ASD surgery using pedicle screw fixation systems with rods of different materials and sizes. Postoperative outcomes (i.e., Cobb, sagittal vertical axis, and pelvic tilt angle) and complications (i.e., pseudarthrosis and rod breakage) were assessed. Random effects models (REMs) pooled data for outcomes reported in ≥ 2 studies. Results Among 50 studies evaluating ASD surgery using pedicle screw fixation systems, 17 described rod material/diameter. Postoperative outcomes did not statistically differ between cobalt–chromium (CoCr) vs. titanium (Ti) rods (n = 2 studies; mean [95% confidence interval (CI)] sagittal vertical axis angle: CoCr 37.00° [18.58°–55.42°] and Ti 32.58° [24.62°–40.54°]; mean [95% CI] pelvic tilt angle: CoCr 26.20° [22.87°–29.53°] and Ti 20.15° [18.0°–22.31°]). The pooled proportion (95% CI) of pseudarthrosis was 15% (7–22%) for CoCr and 12% (− 8–32%) for stainless steel (SS) (n = 2 studies each; Chi2 = 0.07, p = 0.79). The pooled proportion (95% CI) of broken rods was 12% (1–22%) for Ti (n = 3 studies) and 10% (2–19) for CoCr (n = 1 study). Among 6.0–6.35 mm rods, the pooled (95% CI) postoperative Cobb angle (n = 2) was 12.01° (9.75°–14.28°), sagittal vertical axis angle (n = 4) was 35.32° (30.02°–40.62°), and pelvic tilt angle was 21.11° (18.35°–23.86°). Conclusions For ASD patients undergoing posterior fixation and fusion, there are no statistically significant differences in postoperative outcomes or complications among rods of varying materials and diameters. Benchmark postsurgical outcomes and complication rates by rod material and diameter are provided. Level of Evidence III

Objectives To investigate canine retraction (CR) and anchorage loss (AL) among average facial height (AFH) and high facial height subjects (HFH) with or without piezocision surgery (PS). Materials and Methods This was a split-mouth, randomized clinical trial. Twenty-three females (aged 19.05 ± 2.95 years) who presented with Class II division I malocclusion requiring bilateral maxillary extraction and who fulfilled eligibility criteria were included and categorized into two groups: AFH (12 participants) and HFH (11 participants). Atraumatic extractions were performed 10 weeks following bonding. Before space closure, impressions were taken to fabricate models, which were scanned to generate digital models. Each participant had PS on the randomly assigned side. Space closure was undertaken using 100-g nickel-titanium coil closing springs on 0.019 × 0.025-inch stainless steel archwire. Digital models were collected 6 and 12 weeks post-PS. They were superimposed using reliable reference points and a region of interest on the palate, and crown movements were analyzed in three dimensions. Results Three months post-PS, intergroup comparisons showed that rates of CR for control sides (mean = 1.88 ± 0.83 mm for AFH, mean = 1.76 ± 0.62 mm for HFH) and intervention sides (mean = 1.48 ± 0.74 mm for AFH, mean = 1.40 ± 0.85 mm for HFH) were not significantly different. AL was not significantly different (P > .05) between groups. Conclusion Regardless of whether the patient underwent PS, CR and AL rates for AFH and HFH patients were not significantly different.

Objective The aim of this study was to evaluate the effect of screw insertion angle and insertion torque on the mechanical properties of a 3.5 fixed-angle locking plate locking compression plate (LCP) and 3.5 variable-angle locking plate polyaxial locking system (PLS). Methods In the LCP group, screws were placed abaxially at 0, 5 and 10 degrees. In the PLS group, screws were placed at 0, 5, 10, 15 and 20 degrees abaxially. The insertion torque was set to 1.5 and 2.5 Nm in the LCP and PLS groups respectively. A load was applied parallel to the screw axis, and the screw push-out force was measured until the locking mechanism was loosened. Results The 3.5 LCP showed higher push-out strength than the 3.5 PLS when the screws were placed at 0 degree regardless of the insertion torque. The off-axis insertion of 3.5 LCP locking screws resulted in a significant decrease in push-out strength (p Conclusion The 3.5 PLS is more sensitive to the screw insertion angle than to the insertion torque, whereas the 3.5 LCP is affected by both factors. Placing 3.5 LCP locking screws off-axis significantly reduces the screw holding strength; therefore, this approach has to be avoided. The findings of our research indicate that a 1.5 Nm torque can be used for a 3.5 PLS.

This overview analyzed the quality of the systematic reviews (SRs) available on treatments for molar-incisor hypomineralization (MIH).Six electronic databases were searched (PubMed/MEDLINE, Scopus, Web of Science, LILACS, Brazilian Bibliography of Dentistry and Cochrane Library) until March 2022. Two reviewers independently performed the selection, the quality assessment (Assessment of Multiple Systematic Reviews 2 - AMSTAR-2), and the risk of bias assessment of the SR (Risk of Bias in Systematic Reviews - ROBIS).Two hundred nine records were retrieved; after removing duplicates and applying the inclusion/exclusion criteria, 5 SRs remained. Three SRs were rated as showing critically low methodological quality and high risk of bias, and two were rated as moderate methodological quality and low risk of bias. The identified treatments that may be suitable for MIH were classified as (1) non-invasive - casein incorporated into toothpaste and sugar-free chewing gum, toothpaste containing arginine, 0.4% stannous fluoride gel; fluoride varnish; (2) micro-invasive - resin sealants for pits and fissures, microabrasion, dental whitening, resin infiltration; (3) invasive - ART restorations, indirect restorations (metal, composite, or ceramic); and (4) mixed intervention - stainless steel crowns.Despite the considerable number of published papers included in this set of systematic reviews, the evidence supporting the effectiveness of treatments for treating MIH is limited due to the methodological quality and risk of bias of the systematic reviews, as well as the quality of the primary studies (PROSPERO: CRD42020144831).Different treatments have been purposed for MIH treatment, but there is still not enough scientific evidence of good quality for the establishment of a definitive clinical protocol for the treatment of MIH.

The aim was to compare the glide path and final preparation times of WaveOne Gold and TruNatomy in conjunction with two different endodontic access cavity designs in extracted human molar teeth.60 extracted human mandibular molars with mesiobuccal canals were selected and randomly divided into two different access cavity design preparation groups (n = 30). Traditional access cavities (TAC) and conservative access cavities (CAC). Within each cavity design group, the 30 teeth were divided in to two instrumentation groups (WaveOne Gold Primary (n = 15) and TruNatomy Prime (n = 15)). Group 1: TAC, #10 stainless steel manual K-file followed by WaveOne Gold Glider and WaveOne Gold Primary. Group 2: CAC, #10 stainless steel manual K-file followed by WaveOne Gold Glider and WaveOne Gold Primary. Group 3: TAC, #10 stainless steel manual K-file followed by TruNatomy Orifice Modifier and Glider and TruNatomy Prime. Group 4: CAC, #10 stainless steel manual K-file followed by TruNatomy Glider and TruNatomy Prime. Glide path and final preparation times were recorded.Shaping time with TruNatomy Glider in combination with TruNatomy Prime instruments were faster compared to the WaveOne Gold Glider/ WaveOne Gold Primary instruments regardless of the type of access cavity preparation. TAC design yielded faster preparation time (38.2 ± 4.57 seconds) compared to the CAC (55.6 ± 6.91 seconds) in the WaveOne Gold Glider/ WaveOne Gold Primary instrumentation group. No difference was found between the different access cavity design groups in combination with TruNatomy Glider/TruNatomy Prime preparation.Preparation time with TruNatomy Glider and Prime instruments was significantly faster than WaveOne Gold Glider/WaveOne Gold Primary, regardless of the access cavity design. TAC design in combination with WaveOne Gold Glider/ WaveOne Gold Primary instrumentation resulted in faster preparation time compared to WaveOne Gold Glider/WaveOne Gold in combination with the CAC design.

The Essure® permanent contraceptive implant, comprised of four alloys (nickel-titanium, 316L stainless steel, platinum-iridium, and tin-silver solder) and Dacron (PET) fibers, has been approved for use in the US for about two decades. However, little has been published on this implant's biomaterials performance, and as this implant gains interest in terms of in vivo performance, methods of implant post-retrieval storage also need to be assessed. This study investigated the electrochemical properties and ion release profile of Essure® during storage in phosphate buffered saline (PBS), 10 mM H

Research Grants Council Hong Kong under its Theme-based Research Scheme ( SureFire project (T22-505/19-N);RGC Hong Kong GRF Scheme and HK PolyU.

Objectives. Ideal root canal shaping might be more challenging particularly in cases with severely curved canals or complex anatomical variations. Glide path preparation is suggested as a critical step to achieve ideal canal preparation. The present study is aimed at evaluating transportation at different levels of the canal following glide path preparation by five different path finders. Materials and Methods. The study was conducted on 100 S-shaped canal simulator blocks. Glide path was prepared in five groups including (1) Scout RaCe (#10 and #15, 0.02), (2) One G (#14, 0.03), (3) PathFile (#13 and #16, 0.02), (4) GPS (#15, 0.03), and (5) K file (#15, 0.02) (Control group). The first four groups were NiTi rotary instruments, while the last group was a stainless steel hand file. The aforementioned files were used after canal negotiation by a #10 stainless steel hand file. Before- and after-preparation photos were taken and were superimposed in Adobe PhotoShop CC 2019. Transportation measurements were conducted in Digimizer. Absolute canal transportation was calculated at 10 cross-sections. Intergroup and intragroup data analysis were conducted using one-way and repeated measures ANOVA tests, respectively, in SPSS 26.0. The significance level was set to 0.05. Results. Although K file led to significantly more transportation in the apical and middle thirds ( p < 0.001 ), rotary groups were not statistically different. In the coronal third, K files led to significantly more transportation compared to Scout RaCe and PathFile ( p < 0.05 ). Conclusion. Within the limitations of the present study, regardless of the recruited rotary system, glide path preparation using NiTi rotary instruments leads to less canal transportation compared to stainless steel hand files.

In order to treat antibiotic wastewater with high efficiency and low energy consumption, this study proposed the coupling of electrocatalytic degradation and biodegradation, and explored a new modified electrocatalytic material in the coupling system. The stainless-steel mesh based molybdenum carbide (SS-Mo

With the awakening of environmental awareness, the importance of air quality to human health and the proper functioning of social mechanisms is becoming increasingly prominent. The low cost and high efficiency of catalytic technique makes it a natural choice for achieving deep air purification. Stainless steel alloys have demonstrated their full potential for application in a variety of catalytic fields. The diversity of 3D networks or fibrous structures increases the turbulence within the heterogeneous catalysis, balance the temperature distribution in the reaction bed and, in combination with a highly thermally conductive skeleton, avoid agglomeration and deactivation of the active components; corrosion resistance and thermal stability are adapted to highly endothermic/exothermic or corrosive reaction environments; oxide layers formed by bulk transition metals activated by thermal treatment or etching can significantly alter the physico-chemical properties between the substrate and active species, further improving the stability of stainless steel catalysts; suitable electronic conductivity can be applied to the electrothermal catalysis, which is expected to provide guidance for the reduction of intermittent emission exhausts and the storage of renewable energy. The current applications of stainless steel as catalyst or support in the air purification have covered soot particle capture and combustion, catalytic oxidation of VOCs, SCR, and air sterilization. This paper summarizes several preparation methods and presents the relationships between the preparation process and the activity, and reviews its application and the current status of research in atmospheric environmental management, proposing the advantages and challenges of the stainless steel-based catalysts.

Objectives. To evaluate the efficacy of computer-aided design/computer-aided manufacturing (CAD/CAM) technology in interventions implemented in orthodontics. Methods. A scoping review of scientific evidence was accomplished, involving different databases. MesH terms and keywords were provided to examine clinical trials (CTs) in all languages. Exclusively CTs that fulfilled the eligibility criteria were admitted. Results. Eight CTs were chosen. These experiments evaluated 542 patients. Four CTs compared the computer-aided indirect bonding method versus the traditional direct bonding of orthodontic brackets. Three CTs compared CAD/CAM retainers with other types of retainers, and one CT compared the CAD/CAM group with multistranded stainless steel wires versus stainless steel wires. Regarding the efficacy of the interventions with CAD/CAM technology used in orthodontics, variable results were found. The indirect bonded customized CAD/CAM brackets presented just a slight effect on the treatment efficacy and therapy results. Two CTs showed that an indirect bonding self-ligating standard system had a similar quality of therapy in comparison with the CAD/CAM customized bracket system. Concerning the clinical failure rate, no differences were presented between the CAD/CAM retainer and other retainers. A CAD/CAM system had more loose brackets than a noncustomized system and was observed also a greater amount of immediate debonding with CAD/CAM indirect bonding than with direct bonding. CAD/CAM fixed retainers revealed inferior relapse and fewer failures than lab-based and conventional chairside retainers. No changes between treatment groups were observed regarding the total therapy time, amount of appointments, and quantity of archwire bends. Conclusions. In general terms, no greater efficacy of CAD/CAM technology was observed over traditional therapies used in orthodontics. However, it was found that gingival inflammation and the accumulation of bacterial plaque and dental calculus were lower when CAD/CAM retainers were used. When comparing interventions that include CAD/CAM systems with conventional therapies, no significant reduction in care times was found.

The main objective of the EU-funded project mitigating environmentally-assisted cracking through optimisation of surface condition (MEACTOS) was to gain knowledge on the ability of different surface machining procedures to mitigate environmentally-assisted cracking (EAC) in typical light water reactor structural materials and environments. Surfaces of cold-worked (CW) type 316L austenitic stainless steel and nickel-based weld metal Alloy 182 flat tapered tensile specimens were machined using different processes. EAC initiation susceptibility of these specimens was evaluated using constant extension rate tensile (CERT) tests under simulated boiling water reactor (BWR) and pressurized water reactor (PWR) conditions and assessed using constant load experiments. More than a hundred tests were performed covering about 10 years of autoclave testing time. Only minor or no measurable improvements in EAC initiation susceptibility as a function of surface treatments (grinding or advanced machining) compared to the standard industrial face milling were demonstrated. In most cases, the stress thresholds for EAC initiation determined in constant load tests confirmed the trend obtained from CERT tests. This paper summarises the most important results and conclusions concerning the EAC initiation behaviour for the CW 316L and Alloy 182 under reducing PWR and oxidizing BWR conditions.

In this research, mono- and dual-species biofilms of Escherichia coli (O45:H2 and O121:H19) and Salmonella enterica serovar Typhimurium formed on stainless-steel coupons were treated with 100 mg/L NaClO for 1 min. Confocal laser scanning microscopy (CLSM) was applied to investigate the spatial structural dynamics of mono- and dual-species biofilms, and nuclear magnetic resonance (NMR) spectroscopy was employed to further investigate their metabolic responses toward chlorine. CLSM results indicated that mixed-species biofilms (total biovolume, 148,000 to 167,000 μm(3)) stimulated the growth of biomass 2 to 6 times that of single-species biofilms. Upon chlorine treatment, E. coli O45 and S. Typhimurium achieved less reduction (P < 0.05) when coexisting in mixed biofilms (0.70 and 1.17 log CFU/coupon reductions, respectively) compared with their corresponding single-species biofilms (1.97 and 2.01 log CFU/coupon reductions, respectively), while for E. coli O121, more reduction (P < 0.05) was achieved in a mixed biofilm (1.37 log CFU/coupon reductions) compared with its single-species biofilm (0.59 log CFU/coupon reductions). Moreover, NMR results suggested that the increase of putrescine (antioxidation regulator) and the decrease of glucose (enhanced glycolysis for energy replenishment) might contribute to the improved chlorine tolerance in mixed biofilms. Overall, dual-species biofilms promoted biofilm growth and their chlorine tolerance. This study improved our knowledge of the metabolic difference of single- and mixed-species biofilms of E. coli and Salmonella to chlorine sanitization and raised an urgency to investigate the effectiveness of common disinfectants against multispecies consortia. IMPORTANCE Outbreaks of Escherichia coli and Salmonella in food might be associated with the cross-contamination of biofilms on food-contact surfaces. The knowledge of the sanitization of mono-species biofilm on the food-contact surface is well established, while mixed-species biofilm occurs more naturally, which could profoundly affect the efficacy of sanitizer. Therefore, this research aims to evaluate the efficacy of using chlorine against single- and dual-species biofilms of E. coli and Salmonella along with the underlying bacterial metabolic responses. The responses of a mixed biofilm of E. coli and Salmonella to chlorine sanitization were clarified, providing insights to develop a targeted and green sanitization strategy against specific pathogens by perturbing their most susceptible metabolism pathway without sanitizer residue.

Even with the exponential popularity of the contemporary clear aligners, the main stream of orthodontic practice still remains to be metal braces especially in adolescent age-group.

Although stainless steel crowns (SSCs) on permanent molars are a common interim full-coverage restoration, there are few clinical studies on longevity.To evaluate the longevity of SSCs as restorations on young permanent first molars (PFMs) that have undergone vital pulp therapy (VPT) treatment and to identify factors associated with SSC treatment failure.This study conducted a retrospective chart review of children who had PFMs that have undergone VPT treatment and been restored with SSCs. Data from treatment and follow-up visits were collected. The Kaplan-Meier survival analysis was used to analyse the longevity of SSCs. A multivariate Cox proportional hazards regression model was used to identify factors associated with SSC treatment failure.Data from 140 SSCs were included, with an average follow-up period of 33.5 ± 21.6 (range, 6-104) months. Although none of the teeth had pulpal failure, 35.7% had SSC treatment failure. The survival probabilities of SSCs declined over time, reaching 39.6% (95% CI 27.0-51.9) after 60 months. The immediate post-operative condition of SSCs and the loss of proximal wall on the abutment tooth were significant factors associated with SSC treatment failure.Stainless steel crowns are suitable for use as interim restorations in PFMs that have undergone VPT treatment in children, but their longevity is limited, necessitating replacement over time.

Research into Piscirickettsia salmonis biofilms on materials commonly used in salmon farming is crucial for understanding its persistence and virulence. We used the CDC Biofilm Reactor to investigate P. salmonis (LF-89 and EM-90) biofilm formation on Nylon, Stainless steel (316L), Polycarbonate and High-Density Polyethylene (HDPE) surfaces. After 144 h of biofilm visualization by scanning confocal laser microscopy under batch growth conditions, Nylon coupons generated the greatest biofilm formation and coverage compared to Stainless steel (316L), Polycarbonate and HDPE. Additionally, P. salmonis biofilm formation on Nylon was significantly greater (p ≤ .01) than Stainless steel (316L), Polycarbonate and HDPE at 288 h. We used Nylon coupons to determine the kinetic parameters of the planktonic and biofilm phases of P. salmonis. The two strains had similar latencies in the planktonic phase; however, LF-89 maximum growth was 2.5 orders of magnitude higher (Log cell ml

Mortar-based composites are an emerging technology for the repair and strengthening of reinforced concrete and masonry structures. In most cases, the effectiveness of the retrofitting work relies on the substrate-to-composite bond capacity but in some applications, connectors are also used to prevent debonding and improve the performance of the retrofitted structure. Indeed, the use of connectors is recommended by design guidelines and suppliers are required to test them for acceptance. The paper presents a laboratory investigation on steel reinforced grout connectors, made by rolling ultra-high tensile strength steel textiles, comprising either galvanized or stainless-steel micro cords. Tensile tests were first carried out for mechanical characterization. Pull-out tests were then performed on connectors installed in holes drilled in wall panels and injected with either cement or lime mortars. Concrete, tuff masonry, brickwork and limestone masonry were used as substrate materials. Test results are commented to analyze the effect of textile rolling on tensile response, of textile and matrix properties on pull-out strength and failure mode, as well as to highlight their significance for design purposes.

Salmonella can be isolated from animal food, ingredients, and animal food manufacturing surfaces. There are limited data regarding the sanitation of animal food manufacturing surfaces. This experiment evaluated the effects of nine chemical treatments on reduction of Salmonella Typhimurium contamination on various manufacturing surfaces. This experiment was a 9 × 5 factorial with nine chemical treatments and five surfaces. The nine chemical treatments included one with no inoculation or sanitation treatment (negative control). In the other eight treatments, inoculation with Salmonella Typhimurium was followed by either no sanitation treatment (positive control) or treatment with ground corn; liquid commercial formaldehyde; liquid food-grade sanitizer; liquid medium chain fatty acid blend of caprylic, caproic, and capric acids (MCFA); dry commercial calcium propionate; dry commercial acidulant; and dry commercial benzoic acid. The five surfaces included stainless steel, plastic, polypropylene tote bag, rubber belt, and rubber tire. Plastic had higher levels of Salmonella in the positive control than did the polypropylene tote bag; other surfaces had intermediate levels (P0.05). Surfaces treated with formaldehyde had no detectable Salmonella after treatment, and surfaces treated with MCFA had at least a 4-log reduction compared to the control (P0.05). The dry acidulant was the most effective dry sanitizer tested, but it had no impact on Salmonella concentration on rubber tires (P0.05). Whereas liquid sanitizers were the most effective in this experiment, they have limitations for use in dry bulk systems. In summary, formaldehyde, food-grade sanitizer, and MCFA were the most effective chemical treatments to reduce Salmonella surface contamination. Surface type can also influence Salmonella mitigation strategies; specifically, stainless steel and plastic can be more challenging to sanitize within animal food facilities.

Background Afghan refugee children resettled in Washington State have the highest prevalence of elevated blood lead levels (BLLs) of any other refugee or immigrant population. Resettled families brought several lead-containing items with them from Afghanistan, including aluminum cookpots. Objectives To evaluate the potential contribution of lead-containing cookpots to elevated BLLs in Afghan children and determine whether safer alternative cookware is available. Methods We screened 40 aluminum cookpots for lead content using an X-ray fluorescence (XRF) analyzer and used a leachate method to estimate the amount of lead that migrates into food. We also tested five stainless steel cookpots to determine whether they would be safer alternatives. Results Many aluminum cookpots contained lead in excess of 100 parts per million (ppm), with a highest detected concentration of 66,374 ppm. Many also leached sufficient lead under simulated cooking and storage conditions to exceed recommended dietary limits. One pressure cooker leached sufficient lead to exceed the childhood limit by 650-fold. In contrast, stainless steel cookpots leached much lower levels of lead. Significance Aluminum cookpots used by refugee families are likely associated with elevated BLLs in local Afghan children. However, this investigation revealed that other U.S. residents, including adults and children, are also at risk of poisoning by lead and other toxic metals from some imported aluminum cookpots. Impact Statement Some aluminum cookware brought from Afghanistan by resettled families as well as cookpots available for purchase in the United States represent a previously unrecognized source of lead exposure.

Laser welding is distinguished by low heat input, low distortion, high travel speeds and accuracy. Traditional high-power pulsed wave (PW) lasers are being replaced by high-frequency low-pulse energy fibre lasers. However, as these lasers operate at very high frequencies, near continuous wave (CW) operation, it is not clear the benefit of such frequencies in comparison to CW lasers for micro-welding. In this project, two lasers, one in high-frequency PW and another in CW are operated at the same conditions, including average power, average peak power, spot size and travel speed, and the differences in material response are investigated. It has been shown that frequency is one of the important parameters that affect the heat loss between individual pulses, referred to as inter-pulse losses. At low frequency, the PW laser provided lower melting efficiency and higher penetration efficiency than CW. On the other hand, at high frequency, the PW resulted in lower melting and penetration efficiency than CW. In addition, a new definition of interaction time has been proposed to capture conduction losses by travel speed and heat inter-pulse losses due to periodic lack of laser power. This allows a like-for-like comparison of CW and PW lasers and can be used to predict penetration depth with processing parameters.

Meat contamination by Salmonella enterica is a serious public health concern. Available data have suggested that biofilm formation at processing plants and contaminated contact surfaces might contribute to meat contamination. Because transfer from contact surfaces to food products via direct contact has been deemed the most common bacteria transmission route that can lead to contamination, we evaluated the effect of Salmonella biofilm forming ability, contact surface material, and beef surface tissue type on Salmonella biofilm transfer from hard surfaces to beef products. Salmonella biofilms developed on the common contact surfaces stainless steel (SS) and polyvinylchloride (PVC) were transferred consecutively via 30 s of direct contact to either lean muscle or adipose tissue surfaces of 15 pieces of beef trim. The Salmonella biofilm cells could be effectively transferred multiple times from the contact surfaces to the beef trim as indicated by quantifiable Salmonella cells on most meat samples. Biofilm forming ability had the most significant impact (P0.05) on transfer efficiency. More cells of Salmonella strains that formed strong biofilms were transferred after each contact and contaminated more meat samples with quantifiable cells compared with strains that formed weak biofilms. Contact surface materials also affected transferability. Salmonella biofilms on SS transferred more efficiently than did those on PVC. In contrast, the two types of meat surface tissues were not significantly different (P0.05) in biofilm transfer efficiency. Beef trim samples that were in contact with biofilms but did not have quantifiable Salmonella cells were positive for Salmonella after enrichment culture. Our results indicate the high potential of Salmonella biofilms on common contact surfaces in meat processing plants to cause product cross-contamination.

Background The PathogenDx EnviroX-F uses microarray technology to simultaneously detect Listeria species, Listeria monocytogenes, and Salmonella species from environmental samples without the need for enrichment. Objective The validation study included a matrix study of four matrices (stainless steel, plastic, rubber, and sealed concrete) comparing the PathogenDx EnviroX-F assay to the US Food and Drug Administration (FDA) Bacteriological Analytical Manual (BAM) Chapter 10, “Detection of L. monocytogenes in Foods and Environmental Samples, and Enumeration of L. monocytogenes in Foods” (revised March 2017), and FDA BAM Chapter 5,“Salmonella” (revised February 2020). Other required Performance Tested MethodSM parameters evaluated included: inclusivity and exclusivity, robustness, instrument variation, and product consistency and stability. Methods The PathogenDx EnviroX-F assay was evaluated with 30 unpaired replicate surface areas for each environmental surface. The candidate method was evaluated without an enrichment step. Results In the inclusivity and exclusivity study 50 out of 50 Listeria isolates were detected, 50 out of 50 L. monocytogenes strains were detected, 108 out of 108 Salmonella strains were detected, and 95 out of 95 exclusivity strains were correctly excluded. In the matrix study, the PathogenDx EnviroX-F assay showed no significant differences between confirmed results or between candidate and reference method results for 4” × 4” environmental surface areas for each matrix. Conclusion The PathogenDx EnviroX-F assay is an effective method for the qualitative detection of Listeria spp., L. monocytogenes, and Salmonella spp. from environmental surface swabs. Highlights The PathogenDx EnviroX-F assay will be the first PTM-approved multiplex assay for Listeria spp., L. monocytogenes, and Salmonella without the need for an environment step.

To move towards a more sustainable concrete, the enhancement of its durability is strongly encouraged and, dealing in particular with reinforced concrete (RC), this mainly means to prevent the damage due to environmental actions, e.g. due to chloride-induced corrosion. Therefore, there is the need of models aimed at designing durable structures. Usually the service life design models consider concrete in uncracked condition. In real structures, however, several phenomena can generate cracks on concrete surface, leading to an acceleration of the corrosion of steel rebar. A number of studies have been recently carried out in order to evaluate the influence of cracks on reinforced concrete durability in chloride-contaminated environment, however the knowledge of the effect of cracks on the initiation and propagation periods is still lacking. Furthermore, few studies have considered additional protection strategies, such as the use of stainless steel rebar. In this work, experimental results are presented concerning the influence of cracks on the service life of reinforced concrete structures in order to evaluate if cracks lead to an earlier corrosion initiation induced by chlorides. Prismatic specimens, reinforced with carbon steel and 304L stainless steel bars, were longitudinally cracked and exposed to ponding with 3.5% NaCl solution. The monitoring of corrosion behaviour showed that when cracks reached the steel surface corrosion initiated immediately.

Fretting corrosion is associated with increased risk of premature implant failure. In this complex in vivo corrosion system, the contribution of static crevice corrosion of the joined metal alloys is still unknown. The aim of this study was to develop a methodology for testing crevice corrosion behavior that simulates the physiological conditions of modular taper junctions and to identify critical factors on corrosion susceptibility. Samples of medical grade CoCr28Mo6 cast and wrought alloy, TiAl6V4 wrought alloy and REX 734 stainless steel were prepared metallographically and the microstructure was investigated using scanning electron microscopy (SEM). Crevice formers that mimic typical geometries of taper junctions were developed. Crevice corrosion immersion tests were performed in different physiological fluids (bovine serum or phosphate buffered saline with additives of 30 mM H

Finite element models that simulate the effects of class II elastics on the mandibular arch in six different scenarios, using various immobilization methods of the posterior dentition, were studied. Per-element distribution of linear elastic stress-strain and total displacement was computed. Maximum strain on the PDL and maximum stress on alveolar bone increased with posterior tip-back and with the use of archwires vs. aligners. The configuration of the dentition affects the performance of aligners. They perform best on an unlevelled mandibular arch. Applying class II elastics results in vertical side effects that can be modulated by various mandibular stabilization methods. This is likely to be clinically relevant for high-angle patients and may explain the differing effects on the facial profile observed using various treatment modalities. 1-Increasing mandibular molar tip-back generally resulted in less eruption tendencies, with mandibular anchorage preparation resulting in the least amount of calculated vertical displacement. 2-Unexpectedly, with class II forces the use of aligner technology on an unlevelled curve of Spee resulted in improved vertical control when compared to aligner use on a levelled dentition. 3-Generally, using an archwire results in better transmission of stresses to adjacent teeth than the use of aligners. 4-Simulating interarch elastics requires implementing a medial component/orientation of the forces to better emulate clinical situations. 5-A hypothetical configuration: 15

Objectives To evaluate the effect of nitrogen (N)-doped titanium dioxide (TiO2) coated stainless steel brackets activated with natural visible light and dental operating lights on Streptococcus mutans concentration in the plaque of orthodontic patients at 30 and 60 days. Materials and Methods A total of 30 patients were recruited for this split-mouth study; 60 upper lateral incisor brackets constituted the study sample. A total of 30 brackets (15 right and 15 left) were coated with N-doped TiO2 using the (radio frequency) magnetron sputtering method. Plaque samples were collected at 30 days and 60 days after appliance placement. S mutans concentration was evaluated using real-time polymerase chain reaction. Results At both time intervals, the concentration of S mutans in the control group was greater than that in the study group (P = .005). In both the study and the control groups, the S mutans concentrations significantly increased from 30 to 60 days (P = .005). Conclusions N-doped TiO2, on exposure to natural visible light and dental operating light, was effective in reducing the plaque concentration of S mutans in orthodontic patients. The efficacy was better at 30 days than at 60 days after placing the orthodontic appliances.

Sustainable product design has a role in reducing environmental impacts and can provide economic and social benefits for stakeholders. Design is one way to make improvements and provide an overview of alternative solutions to problems. One of the problems of motorcycle users is experiencing the incidence of punctured tires. This research aims to design a tool to help users of automatic and manual motorcycles when a flat tire occurs. The tool design with dimensions of 160 mm x 190 mm x 100 mm uses a 2 mm iron plate as the mainframe, rubber-type wheels on the front and live caster on the back, and stainless steel for bolts and nuts. Testing the tire leak tool uses three motorcycles with automatic and manual types that have an engine capacity of up to 110 cc, and has a wheel size of 62.09 mm for automatic motorbikes and 65.79 mm for manual motorbikes. The test results showed it function well. The tool is stable and safe when used at a speed of 20 km/hour. The tire leak tool can be used on various types of road surfaces and can withstand passenger loads of up to 65 kg. The trial process was carried out 7 times in the environment around the Purwokerto Telkom Institute of Technology campus with up and down road surfaces and various variations of bends. The tool design is easy to install on leaking wheels and is convenient to carry on the go. A tire leak tool can be used as an alternative for motorcyclists when a flat tire occurs, especially automatic and manual motorbikes.

Bacillus toyonensis (a Gram-positive bacterium) and Pseudomonas aeruginosa (a Gram-negative bacterium) isolated from the different surfaces of a dairy plant in our previous study were selected as the test bacteria for the present study. These two test bacteria were investigated in terms of their attachment on the stainless steel test surfaces in a model dairy batch system. After incubation at 5 °C and 20 °C for 6 h, 12 h, and 24 h, stainless steel plates were examined using cultural counts, profilometer, scanning electron microscopy (SEM), and fluorescent microscopy. Also, the test plates were subjected to a cleaning/disinfection procedure used in the dairy plant. Tests were employed before and after the cleaning/disinfection procedures. Cell wall characteristics and holding temperature were found to be significant for the attachment of the test bacteria to stainless steel test surfaces. In the study, the effect of the holding temperature varied depending on the type and characteristics of the bacteria. The adhesion ability of P. aeruginosa was higher than that of B. toyonensis. Increases in the holding temperature may increase the adhesion ability of the bacteria. Milk growth medium was found to be more successful in preventing the attachment ability of P. aeruginosa compared to B. toyonensis. This indicates that the chemical characteristic of the contact material may affect adhesion. The adhered bacterial cells were entirely removed by means of the cleaning/disinfection treatment. Therefore, the adhesion of bacterial cells could be explained as "initial phase of biofilm formation." It can be concluded that the microorganism cell adhesion on the surface is followed by biofilm formation, and this situation lasts for many years. These results reveal the importance of controlling biofilm formation in dairy plants from the beginning.

Water-miscible cooling lubricants are used in approx. 90% of metalworking processes mainly for lubrication and cooling of the contact zone between tool and workpiece. The base oils of the widely used water-miscible emulsions are often of mineral origin and represent a significant share of the CO2-fingerprint in production systems in terms of their extraction, processing and the possibility of recycling. Cooling lubricants are furthermore negatively discussed regarding to their health compatibility. Those disadvantages of conventional cooling lubricants drive the research for replacing mineral base oils with vegetable base oils, which contribute to a safer work environment and greener production. In this work, both conventional cooling lubricants and several water-miscible emulsions with various edible and non-edible vegetable-based oils were prepared and characterized regarding their suitability as cooling lubricants for the milling of aircraft stainless steels. Comprehensive experimental investigations were carried out to determine the process forces and the resulting tool wear as technical performance indicators for the test evaluation.

A laser-induced periodic surface structure (LIPSS) was shown to have antibacterial adhesion properties in previous research. In this study, the antibacterial performance of LIPSS on traditional biometals (stainless steel and titanium alloy) and a potential biometal (zirconium-based bulk metallic glass, Zr-BMG) was investigated. A femtosecond laser was used to fabricate LIPSS on the specimens. Gram-negative

The main objective was to develop a wipe sampling test to measure surface contamination of the most frequently used antineoplastic drugs (ADs) in Swedish healthcare and furthermore to develop an analysis method sensitive enough to assess low levels of contamination. Two wipe sampling tests with separate sample processing methods assessing i) cyclophosphamide (CP), ifosfamide (IF), 5-fluorouracil (5-FU), etoposide (ETO), gemcitabine (GEM) and cytarabine (CYT) (Wipe Test 1), and ii) GEM, CYT and methotrexate (MTX) (Wipe Test 2), respectively were developed by optimization of absorption and extraction efficiencies using different wipe tissue materials, tissue wetting solution and extraction solvents. A fast LC-MS/MS method was developed for simultaneous detection of the studied ADs. The limit of quantification for the method was between 0.04 to 2.4 ng/wipe sample (0.10 to 6.1 pg/cm2 for an area of 400 cm2) and at 50 ng/sample the within-day precision was between 1.3-15%, and the accuracy between 102-127%. Wipe Test 1 was applied in an assessment of cleaning efficiency of five different cleaning solutions (formic acid, water, sodium hydroxide, ethanol and sodium dodecyl sulfate (SDS) for removal of ADs from surfaces made of stainless steel or plastic. For CP, IF, 5-FU, GEM and CYT 92% of the AD were removed regardless of surface and cleaning solution. In conclusion, a user-friendly assessment method to measure low levels of seven ADs in the work environment was developed and validated. Assessment of the decontamination efficiency of cleaning solutions concerning removal of ADs from stainless steel showed that efficiencies differed depending on the AD with water being the least effective cleaning agent. The results suggests that a combination of different cleaning agents including detergent and a solution with an organic component would be optimal to efficiently remove the measured ADs from surfaces in the workplace.