Search

Dyes from industrial wastewaters represent one of the most hazardous pollutants as they are not effectively biodegradable. The present work is focused to study the novel properties of keratin-polyamide blend nanofibrous filtration membranes for treating wastewaters containing dye. Keratin protein was extracted from goat hair, a tannery waste through sulphitolysis process. The extracted keratin was blended with polyamide to prepare a nanofibrous membrane through the electrospinning process. The fabricated pristine polyamide and keratin-altered polyamide membranes were characterized and compared for their properties. Effects of solution pH, dye concentration, membrane flux, and membrane capacity have been examined. Very fine nanofibers and enhanced porosity drive the membrane to enhanced flux and higher filtration efficiencies. At pH 2, the dye removal efficiency of the blend membranes was 100, 99, 98, 90, and 83% for 100, 200, 250, 300, and 400 ppm concentrations of dye, respectively. The keratin-polyamide blend membrane exhibited better properties in all aspects. The results of this present investigation indicate that the presence of keratin in filtration membranes is promising for dye removal from the effluents.

We report a new V activated ZnO host co-doped with Yb3+ and Eu3+ downconversion (DC) phosphor to convert the UV photons to near Infra-red (NIR) photons. The absorption efficiency of the ZnO host with activator Yb3+ is found to get significantly enhanced with V doping. The NIR emission at 980 nm of Yb3+ is enhanced at an optimal concentration of 3 mol% V in ZnO host (ZV). Further, with an additional sensitizer Eu3+, enhanced NIR emission is observed at 980 nm for the corresponding excitation of Eu3+. The mechanisms for the energy transfer from the host (ZV) and sensitizer (Eu3+) to the activator (Yb3+) are discussed in detail. This enables ZV:Eu3+,Yb3+ as an efficient DC phosphor which could enhance the spectral response of Si-solar cells in the UV range.

Due to the high toxicity of effluents radiating from tannery industries, there is a need for effluent treatment so as to limit its dangerous impacts on the environment. Fabricating responsive membranes is gaining significant interest in wastewater treatment applications. This study investigates the preparation, characterization, permeation, and antifouling properties of the keratin-polysulfone blend membranes. Keratin, a bioinspired material, is used as the responsive element along with the polysulfone matrix, which together acts as the responsive membranes for efficient filtration. Keratin was extracted from the goat hair, a tannery waste, through ball milling—an ecological, cost-effective, and time-consuming method. Keratin-polysulfone was blended in the ratio 95:5 (v/v) in their respective solvents to prepare nanofiltration membranes. The morphology of the membranes shows the random arrangement of fibers with the interstitial spaces. Contact angle measurements reveal that the keratin-polysulfone blend membranes are partially hydrophilic, which in turn resulted in good antifouling properties. Improved porosity of the fabricated membranes enabled good absorption capacity, and enhanced mechanical properties are an added advantage for the fabricated membranes. Since the membrane showed enhanced filtration property, the post-tanning effluents from the leather industry have been treated by the keratin-polysulfone fabricated membranes. The treated effluent showed a maximum percentage reduction in chemical oxygen demand (COD) and biological oxygen demand (BOD) concentrations of about 53% and 66%, respectively. The dye removal efficiency of the fabricated membrane is reported to be 76%. Thus, filtration efficiency has been established paving a way for treating effluents in an efficient way.

Dyes from industrial wastewaters represent one of the most hazardous pollutants as they are not effectively biodegradable. The present work is focused to study the novel properties of keratin-polyamide blend nanofibrous filtration membranes for treating wastewaters containing dye. Keratin protein was extracted from goat hair, a tannery waste through sulphitolysis process. The extracted keratin was blended with polyamide to prepare a nanofibrous membrane through the electrospinning process. The fabricated pristine polyamide and keratin-altered polyamide membranes were characterized and compared for their properties. Effects of solution pH, dye concentration, membrane flux, and membrane capacity have been examined. Very fine nanofibers and enhanced porosity drive the membrane to enhanced flux and higher filtration efficiencies. At pH 2, the dye removal efficiency of the blend membranes was 100, 99, 98, 90, and 83% for 100, 200, 250, 300, and 400 ppm concentrations of dye, respectively. The keratin-polyamide blend membrane exhibited better properties in all aspects. The results of this present investigation indicate that the presence of keratin in filtration membranes is promising for dye removal from the effluents.

The spectral modification is noticed through near Infrared (IR) downconversion (DC) in Yb3+, Bi3+ co-doped ZnxNb(1-x)O composite host. A high-intensity blue emission centered at 450 nm is observed upon UV excitation at 270 nm for the host ZnxNb(1-x)O at x = 0.5 (ZN). Doping with the optimized concentration at 4 mol% of Yb3+ with ZN (YZN) initiates an energy transfer from the niobate group to two neighboring Yb3+ ions in a co-operative energy transfer (CET) process. The resulting Yb3+ emission spectrum is around 1000 nm, which matches well with the spectral response of Si solar cells. Introducing 1 mol% of trivalent Bi3+ ions as an additional sensitizer to YZN (BZN), the excitation wavelength is further extended from UV at 270 nm to visible at 450 nm region. As an effect of this, UV excitations at 270 nm, 330 nm, and visible excitation at 450 nm in BZN enhance the luminescence in the near IR region. The DC process observed in BZN is due to the CET process from both the niobate group and Bi3+ ions to Yb3+ ions. Solar panel coated with BZN shows an increase in conversion efficiency which in turn indicates that the synthesized phosphor is a promising material for increasing Si solar cell efficiency.