Search

A novel porous tablet material (PTM) was developed from zirconium pillared montmorillonite (Zr-MMT) by dry pressing technique combined with sacrificial template (polymethylmethacrylate). The developed PTM can be effectively separated from water. The layered structure of montmorillonite was still intact and the three-dimensional interconnected porosity of PTM was evenly distributed, which means that PTM has good permeability. The specific surface area and total pore volume of PTM were 80.04 m 2 /g and 0.28 m 3 /g, respectively, indicating that the PTM can provide a large number of vacant surface active sites. The saturated adsorption capacity to Pb(II) was 215.52 mg/g, which was much higher than that of montmorillonite type clay adsorbents. These findings demonstrate that PTM could be used as separable adsorbent for Pb(II) removal from aqueous solution.

A novel zirconium-pillared montmorillonite (Zr-Mt) porous ceramic (P-ZMt) for Cr 3+ removal was developed by gelcasting. P-ZMt was characterized by XRD, SEM, XPS, TEM, BET. The influence of pH value, contact time, temperature and initial concentration on the adsorption efficiency was investigated. The results revealed that the P-ZMt has a high removal efficiency of Cr 3+ over a broad range of pH value. The pseudo-second-order kinetic model fitted our acquired Cr 3+ adsorption data best, in comparison with the pseudo-first-order kinetic model. The Langmuir model was applied to fit the adsorption process better than that of the Freundlich model. The thermodynamic parameters (∆H, ∆G and ∆S) were also determined, which revealed that the Cr 3+ adsorption process was spontaneous in nature. The present developed P-ZMt could be recovered and reused for more than 6 times. The novel developed P-ZMt is an inexpensive, effective and long-life-cycle adsorbent for Cr 3+ removal from water solution.

A new sorting control system in field programmable gate array (FPGA) — the core of control — was proposed because the previous one couldn’t meet the requirements of the multi-channel and high yield. It focused on designs of both hardware circuit and FPGA programming module. In the system, the accurate lossless delay of multiple signals was applied by using of RAM and its control module in FPGA. The sorting signals were generated based on the parallel execution characteristics of FPGA program. Real-time communication was realized between CAN controller of SPI and human-computer interface. A large number of experiments were done to test the proposed system. Results showed that the sorting control system could process multi-channel and higher-yield signals significantly. And the materials sorter was improved both in detectable level and yield.

A simulated experiment exposing Corbicula fluminea in the Cd contaminated sediment of Lake Taihu was conducted in laboratory to study the bioaccumulation of Cd in Corbicula fluminea and the distribution regularity of Cd in water.The speciation of Cd extracted by DGT and BCR and the releasing regularities were determined in sediments of Lake Taihu to obtain the applicability of predicting sediment quality guidelines.When the contaminated concentration increased,the concentration of Cd extracted by DGT and BCR in overlying water and accumulated in Corbicula fluminea increased.The results showed that the content of Cd in Corbicula fluminea was significantly correlated with the results measured by two methods after 14 days and 28 days exposure.It offered theoretical statistics for the prediction of sediment quality guidelines of Cd.

The leaching characteristics of harmful elements, mainly heavy metals, from fly ash in aqueous solution were analyzed, and fly ash was used as adsorbent to remove Cr(III) in aqueous solution, affecting factors were studied to optimize operation conditions. Desorption effect was checked as well. The results showed that the lixivium of fly ash was alkaline, 7 kinds of metals with different concentrations were detected in solution, and concentration of leaching elements were lower than those of state standard GB5085-85 and GB8978-88 except for pH value. It was safe in aqueous solution without excessive harmful pollution. Fly ash was effective to remove Cr(III), and the operation conditions could affect adsorption capacity to some extent. The optimal environmental condition was of pH 4.5, dosage of fly ash 0.2 g, concentration of Cr(III) 20 mg/L. The temperature affect little on adsorption process, normal temperature is acceptable. Adsorption process was fast and the adsorption capacity was 14.95 mg/g at 10 min, and the maximum desorption rate was 93.0%. The result is of great significance for adsorption mechanism investigation and practical application in future.

In the last years, an increasing attention has been devoted to the utilization of anodic oxidation (AO) technologies for the treatment of wastewater polluted by recalcitrant organics. Recently, Ti4O7 was proposed as a promising anode for AO for the treatment of various organics. Here the potential utilization of commercial Ti4O7 anodes has been evaluated considering the electrochemical treatment of synthetic wastewater contaminated by three very different organic molecules (namely, oxalic acid, phenol and Acid Orange 7), all characterized by a very high resistance to AO. The performances of Ti4O7 were compared with that of two largely investigated anodes: Boron-doped diamond (BDD), which is probably the most effective electrode for AO, and an Ir-based anode which presents a relatively low cost. Moreover, the effect of various operative conditions (current density, mixing rate and initial concentration of the organic) was evaluated by both experimental studies and the adoption of a theoretical model previously developed for BDD anodes. It was shown that the performances of the process can be improved by a proper selection of operative conditions. Moreover, it was found that the proposed model can be effectively used to predict the effect of operative parameters at Ti4O7 anodes, thus helping the process optimization.