Search

Background Low-dose X-ray images have become increasingly popular in the last decades, due to the need to guarantee the lowest reasonable patient’s exposure. Dose reduction causes a substantial increase of quantum noise, which needs to be suitably suppressed. In particular, real-time denoising is required to support common interventional fluoroscopy procedures. The knowledge of noise statistics provides precious information that helps to improve denoising performances, thus making noise estimation a crucial task for effective denoising strategies. Noise statistics depend on different factors, but are mainly influenced by the X-ray tube settings, which may vary even within the same procedure. This complicates real-time denoising, because noise estimation should be repeated after any changes in tube settings, which would be hardly feasible in practice. This work investigates the feasibility of an a priori characterization of noise for a single fluoroscopic device, which would obviate the need for inferring noise statics prior to each new images acquisition. The noise estimation algorithm used in this study was tested in silico to assess its accuracy and reliability. Then, real sequences were acquired by imaging two different X-ray phantoms via a commercial fluoroscopic device at various X-ray tube settings. Finally, noise estimation was performed to assess the matching of noise statistics inferred from two different sequences, acquired independently in the same operating conditions. Results The noise estimation algorithm proved capable of retrieving noise statistics, regardless of the particular imaged scene, also achieving good results even by using only 10 frames (mean percentage error lower than 2%). The tests performed on the real fluoroscopic sequences confirmed that the estimated noise statistics are independent of the particular informational content of the scene from which they have been inferred, as they turned out to be consistent in sequences of the two different phantoms acquired independently with the same X-ray tube settings. Conclusions The encouraging results suggest that an a priori characterization of noise for a single fluoroscopic device is feasible and could improve the actual implementation of real-time denoising strategies that take advantage of noise statistics to improve the trade-off between noise reduction and details preservation.

Additional file 1:Table S1. Noise parameters estimates extracted from the synthetic sequences with variable number of grey levels. Table S2. Errors on noise parameters estimates extracted from the synthetic sequences with variable number of grey levels. All values are expressed as relative errors, except for those reported in blue, which are expressed as absolute errors, since they refer to a null parameter (b = 0). Table S3. Noise parameters estimates extracted from the synthetic sequences designed via the X-ray simulator. Table S4. Errors on noise parameters estimates extracted from the synthetic sequences designed via the X-ray simulator. All values are expressed as relative errors, except for those reported in blue, which are expressed as absolute errors, since they refer to a null parameter (b = 0).

Many studies have accounted for whole body vibration effects in the fields of exercise physiology, sport and rehabilitation medicine. Generally, surface EMG is utilized to assess muscular activity during the treatment; however, large motion artifacts appear superimposed to the raw signal, making sEMG recording not suitable before any artifact filtering. Sharp notch filters, centered at vibration frequency and at its superior harmonics, have been used in previous studies, to remove the artifacts. [6, 10] However, to get rid of those artifacts some true EMG signal is lost. The purpose of this study was to reproduce the effect of motor-unit synchronization on a simulated surface EMG during vibratory stimulation. In addition, authors mean to evaluate the EMG power percentage in those bands in which are also typically located motion artifact components. Model characteristics were defined to take into account two main aspect: the muscle MUs discharge behavior and the triggering effects that appear during local vibratory stimulation. [7] Inter-pulse-interval, was characterized by a polimodal distribution related to the MU discharge frequency (IPI 55-80ms, σ=12ms) and to the correlation with the vibration period within the range of ±2 ms due to vibration stimulus. [1, 7] The signals were simulated using different stimulation frequencies from 30 to 70 Hz. The percentage of the total simulated EMG power within narrow bands centered at the stimulation frequency and its superior harmonics (± 1 Hz) resulted on average about 8% (± 2.85) of the total EMG power. However, the artifact in those bands may contain more than 40% of the total power of the total signal. [6] Our preliminary results suggest that the analysis of the muscular activity of muscle based on raw sEMG recordings and RMS evaluation, if not processed during vibratory stimulation may lead to a serious overestimation of muscular response

Comparison of derivative operators via quantitative performance analysis is rarely addressed in medical imaging. Indeed, the main application of such operators is the extraction of edges and, since there is no unequivocal definition of edges, the common trend is to identify the best performing operator based on a qualitative match between the extracted edges and the fickle human perception of object boundaries. This study presents an objective comparison of four first-order derivative operators through quantitative analysis of results yielded in a specific task, i.e. a spine kinematics application. Such application is based on a template matching method, which estimates common kinematic parameters of intervertebral segments from an X-ray fluoroscopy sequence of spine motion, by operating on the image derivatives of each frame. Therefore, differences in image derivatives, computed via different derivative operators, may lead to differences in estimated parameters of intervertebral kinematics. The comparison presented in this study focused on the trajectory of the instantaneous center of rotation (ICR) of an intervertebral segment, as it is particularly sensitive even to very small differences in displacements and velocities. Therefore, a quantitative analysis of the discrepancies between the ICR trajectories, obtained with each of the four considered derivative operators, was carried out by defining quantitative measures. The results showed detectable differences in the obtained ICR trajectories, thus highlighting the need for quantitative analysis of derivative operator performances in applications aimed at providing quantitative results. However, the significance level of such differences for clinical applications should be further assessed, but, currently, it is not possible, as there is no consensus and sufficient data on kinematic parameters features associated with specific spinal pathologies.

This paper presents an analysis on the suitability of a low cost motion capture system to support the development of generic applications within medical scenarios. In this study we used the Microsoft Kinect (first generation) sensor as basic technology for its wide availability and the relatively low cost, which generated great interest of the scientific community in several application fields. Most of the studies found in literature however, do not address the quality and reliability of the raw data (objects position and depth) considering only the results of the integrated 3D recognition algorithms for the final skeleton/gesture analysis. This can be critical in rehabilitation, in which the knowledge of accuracy, reliability and performance in tracking patient body movements is required and assessed. To this aim, this article proposes an experimental protocol to analyze the Kinect measurement capabilities, via the definition of peculiar parameters. Here we also introduced an analysis of performance versus usage time. Results showed some weak- nesses of the sensor. Specifically, resolution was found in the range of tens of millimeters while degrading over time. The adoption of the Microsoft Kinect (first generation) in medical scenarios should therefore be considered with respect to the application it serves having clear in mind its performances and limitations.

Technological advances have driven some attempt of vital parameters monitoring in adverse environments; these improvements will make possible to monitor cardiac activity also in automotive environments. In this scenario, heart rate changes associated with alcohol consumption, become of great importance to assess the drivers state during time. This paper presents the results of a first set of experiments aimed to discover heart rate variability modification induced by moderate assumption of alcoholic drink (i.e. single draft beer) as that typically occurs in weekend among some people. In the study, twenty subjects were enrolled and for each of them two electrocardiographic recordings were carried out: the first before alcohol ingestion and the second after 25-30 minutes. Each participant remained fasting until the second ECG acquisition was completed. ECG signal were analyzed by typical time-domain, frequency and non linear analysis. Results showed a small increase in LF/HF ratio which reflects a dominance of the sympathetic system over the parasympathetic system, and an increase in signal complexity as proven by non linear analysis. However, the study highlighted the need to monitor HRV starting from alcohol ingestion until its complete metabolization to allow a more precise description of its variation

Infantile Nystagmus Syndrome, or Congenital Nystagmus, is an ocular-motor disorder characterized by involuntary, conjugated and bilateral to and fro ocular oscillations. Good visual acuity in congenital nystagmus can be achieved during the foveation periods in which eye velocity slows down while the target image crosses the fovea. Visual acuity was found to be mainly dependent on the duration of the foveation periods. In this work a new approach is proposed for estimation of foveation parameters: a cubic spline interpolation of the nystagmus recording before localizing the start point of foveation window and to estimate its duration. The performances of the proposed algorithm were assessed in comparison with a previously developed algorithm, used here as gold standard. The obtained results suggest that the spline interpolation could be a useful tool to filter the eye movement recordings before applying an algorithm to estimate the foveation window parameters.

The impact of whole body vibrations (vibration stimulus mechanically transferred to the body) on muscular activity and neuromuscular response has been widely studied but without standard protocol and by using different kinds of exercises and parameters. In this study, we investigated how whole body vibration treatments affect electromyographic signal of rectus femoris during static and dynamic squat exercises. The aim was the identification of squat exercise characteristics useful to maximize neuromuscular activation and hence progress in training efficacy. Fourteen healthy volunteers performed both static and dynamic squat exercises without and with vibration treatments. Surface electromyographic signals of rectus femoris were recorded during the whole exercise and processed to reduce artifacts and to extract root mean square values. Paired t-test results demonstrated an increase of the root mean square values (p

— Long term recording of biomedical signals such as ECG, EMG, respiration and other information (e.g. body motion) can improve diagnosis and potentially monitor the evolution of many widespread diseases. However, long term monitoring requires specific solutions, portable and wearable equipment that should be particularly comfortable for patients. The key-issues of portable biomedical instrumentation are: power consumption, long-term sensor stability, comfortable wearing and wireless connectivity. In this scenario, it would be valuable to realize prototypes using available technologies to assess long-term personal monitoring and foster new ways to provide healthcare services. The aim of this work is to discuss the advantages and the drawbacks in long term monitoring of biopotentials and body movements using textile electrodes embedded in clothes. The textile electrodes were embedded into garments; tiny shirt and short were used to acquire electrocardiographic and electromyographic signals. The garment was equipped with low power electronics for signal acquisition and data wireless transmission via Bluetooth. A small, battery powered, biopotential amplifier and three-axes acceleration body monitor was realized. Patient monitor incorporates a microcontroller, analog-to-digital signal conversion at programmable sampling frequencies. The system was able to acquire and to transmit realtime signals, within 10 m range, to any Bluetooth device (including PDA or cellular phone). The electronics were embedded in the shirt resulting comfortable to wear for patients. Small size MEMS 3-axes accelerometers were also integrated.

The aim of this study is to highlight the relation between muscle motion and electromyographyc activity during whole body vibration. This treatment is accounted for eliciting a reflex muscle activity in response to vibratory stimulation. Simultaneous recordings from quadriceps Rectus Femoris EMG and 3D muscle accelerations on fifteen subjects undergoing vibration treatments were collected. In our study vibrations were delivered via a sinusoidal oscillating platform at different frequencies (10-45 Hz), with a constant amplitude. Muscle motion was estimated by processing accelerometer data. Displacements revealed a mechanical resonant-like behaviour of the muscle; resonance frequencies and dumping factors depended on subject. Large EMG motion artifacts were removed using sharp notch filters centred at the vibration frequency and its superior harmonics. RMS values of artifact-free EMG were found correlated to the actual muscle displacement. The results were in accordance to the hypothesis of a proprioceptive response during vibration treatment. Nevertheless, motion artifacts produced an overestimation of muscle activity, therefore its removal was essential. © 2009 Springer Berlin Heidelberg.

A valuable alternative to US cardiotocography, for fetal surveillance, can be offered by phonocardiography, a passive and low cost acoustic recording of fetal heart sounds. A crucial point is the exact recognizing of the fetal heart sounds, associated to each fetal heart beat, and then the estimation of FHR signal. In this work, software for FHR assessment from phonocardiographic signals was developed. To check the reliability of the software, obtained results were compared with those of simultaneously recorded cardiotocographic signals. Results seemed to be satisfying, as provided FHR series were almost all confined within FHR-CTG +/- 3 bpm, where FHR-CTG were FHR series provided by commercial US cardiotocographic devices, currently employed in clinical routine.

Congenital nystagmus (CN) is an ocular-motor disorder characterised by involuntary, conjugated ocular oscillations, that can arise since the first months of life. Pathogenesis of congenital nystagmus is still under investigation. In general, CN patients show a considerable decrease of their visual acuity: image fixation on the retina is disturbed by nystagmus continuous oscillations, mainly horizontal. However, image stabilisation is still achieved during the short periods in which eye velocity slows down while the target image is placed onto the fovea (called foveation intervals). To quantify the extent of nystagmus, eye movement recording are routinely employed, allowing physicians to extract and analyse nystagmus main features such as shape, amplitude and frequency. Using eye movement recording, it is also possible to compute estimated visual acuity predictors: analytical functions which estimates expected visual acuity using signal features such as foveation time and foveation position variability. Use of those functions add information to typical visual acuity measurement (e.g. Landolt C test) and could be a support for therapy planning or monitoring. This study focus on robust detection of CN patients' foveations. Specifically, it proposes a method to recognize the exact signal tracts in which a subject foveates, This paper also analyses foveation sequences. About 50 eyemovement recordings, either infrared-oculographic or electrooculographic, from different CN subjects were acquired. Results suggest that an exponential interpolation for the slow phases of nystagmus could improve foveation time computing and reduce influence of breaking saccades and data noise. Moreover a concise description of foveation sequence variability can be achieved using non-fitting splines. © 2009 Springer Berlin Heidelberg.

Congenital nystagmus (CN) is an ocular-motor disorder that appears at birth or during the first few months of life; it is characterised by involuntary, conjugated, bilateral to and fro ocular oscillations. Pathogenesis of congenital nystagmus is still unknown. Eye movement recording allow to extract and analyse nystagmus main features such as shape, amplitude and frequency; depending on the morphology of the oscillations nystagmus can be classified in different categories (pendular, jerk, horizontal unidirectional, bidirectional). In general, CN patient show a considerable decrease of the visual acuity: image fixation on the retina is disturbed by nystagmus continuous oscillations; however, image stabilisation is still achieved during the short foveation periods in which eye velocity slows down while the target image is placed onto the fovea. Visual acuity was found to be mainly dependent on foveation periods duration, but cycle-to-cycle foveation repeatability and reduction of retinal image velocities also contribute in increasing visual acuity. This study concentrate on cycle-to-cycle image position variation onto fovea, trying to characterise the sequences of foveation positions. Eye-movement (infrared oculographic or electro oculographic) recordings, relative to different gaze positions and belonging to more than 30 CN patients, were analysed. Preliminary results suggest that sequences of foveations show a cyclic pattern with a dominant frequency (around 0.3 Hz on average) much lower than that of the nystagmus (about 3.3 Hz on average). Sequences of foveations reveals an horizontal ocular swing of more than 2 degree on average, which can explain the low visual acuity of the CN patient. Current CN therapies, pharmacological treatment or surgery of the ocular muscles, mainly aim to increase the patient's visual acuity. Hence, it is fundamental to have an objective parameter (expected visual acuity) for therapy planning. The information about sequences of foveations can improve estimation of patient visual acuity.

Whole Body Vibration training is more and more utilized in sport medicine to enhance athletic performance and training; recently, vibration treatment is being also used for therapy and rehabilitation for patients affected by different pathologies. It is also worth mention that excessive vibrations can be hazardous. The treatment is based on the hypothesis that under some circumstances vibration loads induce specific responses from the neuromuscular system; some clinical evidences suggest mechanical and metabolic reaction. Usually, vibrations are transmitted by means of a platform oscillating at different frequencies (10-80Hz) to patient body; mainly, limb muscles are involved. Many studies about the subject employ surface EMG recordings to evaluate muscle activity during vibration training. On electrodes, this condition generates large motion artifact at the vibration frequency. To get rid of such artifact an adaptive filter was designed: accelerometers placed onto platform or directly on muscles provide an error signal shape to be cancelled from the raw EMG. In particular, surface EMG have been recorded from leg quadriceps muscles of volunteers during whole body vibration therapy sessions at different oscillating frequency. A standard RLS adaptive filter have been used to cancel the motion artifact from EMG in real-time. Results show the effective cancellations of the vibration frequency from the raw EMG; the RMS value of the cleaned EMG results lower than that unprocessed in some cases up to 50%.

Beside other Clinical Engineering activities to reduce risks in hospitals, functional assessment of medical devices is becoming more and more extended. Once evaluated the common risk such those electric and mechanical, specific risk are connected to the device performance: functional assessment aims to verify the specific proper operations of a medical apparatus. In particular, neonatal incubators have the primary aim to maintain an adequate microclimate for the newborn, especially those premature and smaller, who may not be able to regulates body temperature. To prevent newborn heat loss, incubator mainly stabilizes the temperature of the baby compartment to a selected value, reducing the risk of hypothermia. As suggested by the Particular Standards for safety of baby incubators, temperature have to be measured in 5 specific points inside infant chamber: the difference between measured temperatures and that selected on incubator must be limited to fractions of °C. Also the time needed to reach a given temperature must be limited. Other tests should be performed to verify humidity, air velocity, noise level, CO2 concentration, etc.. A prototype device was developed to automatically perform functional assessment of neonatal incubators. A microcontroller continuously performs a 12-bit analog to digital conversion of voltage signals generated by 5 thermal probes and a humidity sensor and sends those data to a PC, where a software process received signal and provide tests. The HW device is of little dimensions, battery powered and capable to continuously transmit data wirelessly, the SW allows real-time signal display, average values, optic and acoustic alarms for limits exceeding, data storage, etc. The device can be easily used to perform periodical functional tests on neonatal incubators. Further analysis of recorded data can be used to evaluate more specific features such as modalities of temperature control, etc.

Whole Body Vibrations consist of a vibration stimulus mechanically transferred to the body. The impact of vibration treatment on specific muscular activity, neuromuscular, and postural control has been widely studied. We investigated whole body vibration (WBV) effect on oxygen uptake and electromyographic signal of the rectus femoris muscle during static and dynamic squat. Fourteen healthy subjects performed a static and dynamic squat with and without vibration. During the vibration exercises, a significant increase was found in oxygen uptake (P=0.05), which increased by 44% during the static squat and 29.4% during the dynamic squat. Vibration increased heart rate by 11.1 ± 9.1 beats.min-1 during the static squat and 7.9 ± 8.3 beats.min-1 during the dynamic squat. No significant changes were observed in rate of perceived exertion between the exercises with and without vibration. The results indicate that the static squat with WBV produced higher neuromuscular and cardiorespiratory system activation for exercise duration ?60 sec. Otherwise, if the single bout duration was higher than 60 sec, the greater cardiorespiratory system activation was achieved during the dynamic squat with WBV while higher neuromuscular activation was still obtained with the static exercise