Search

Coiled tubing (CT) has been widely used for oil and gas exploitation, however corrosion of CT under high pressure and high temperature (HPHT) environment was often reported, also corrosion induced failures of CT welds were often observed to occur during service. Corrosion related behaviors of CT welds are not clear. Therefore, a study of the corrosion resistance of CT welds under HPHT environment is carried out. In order to efficiently evaluate the corrosion resistance of welds, some test samples were obtained by linear cutting out of a CT110 in service on the site. The water samples from gas field were used as the test reagent to simulate the actual corrosive medium. Based on the results of weight loss test under HPHT corrosive environment and tensile test under room conditions, the corrosion sensitivities of the welding seam and base material under various temperatures and partial pressures of CO2 as well as the mechanical properties of the corroded CT were compared and evaluated quantitatively, the corrosion morphologies and material products of the test samples were analyzed by scanning electron microscope (SEM). The test results showed that the corrosion rates of the welding seam in a HPHT caldron were 1.7, 2.0 and 1.2 times of the base metal’s when the total pressure is 4MPa, and the temperature is 30°C, 60°C and 90°C, respectively. The corrosion rates of the welding seam is 2.0, 2.1 and 2.0 times of the base metal’s when the partial pressure of CO2 is 0.1MPa, 0.2MPa and 0.3MPa, respectively. The yield strength of the weld seam after corrosion test was found to be reduced by 4.8% (the yield strength of the base metal was reduced by 4.0%) and its tensile strength was reduced by 8.2% (the base metal was reduced by 7.1%). This indicates that CT weld seam is more susceptible to corrosion than CT base material under service condition.

We describe low-cost fabrication, size control and characterization of borosilicate glass nanopores for sensing of single biomolecules. Nanopores with pore diameters down to ∼100nm were fabricated in borosilicate glass capillaries using table-top carbon-di-oxide laser assisted glass capillary puller. We further achieve controlled reduction in pore diameter by sculpting of glass capillaries under constant electron beam exposure of a scanning electron microscope. We confirm successful fabrication of sub-10nm pores by SEM imaging. We further show electrical characterization and low-noise behavior of these borosilicate nanopores and compare various geometries of pulled conical glass nanopores. We show, for the first time, a comprehensive characterization of glass nanopore conductance across a wide range (1M-1μM) of salt conditions. We show the conditions for the conical pore conductance model to fit to this extended salt range. We also experimentally show, for the first time, the role of buffer conditions in this wide salt range measurement. Finally, we demonstrate single molecule sensing capabilities of these devices with real-time translocation experiments of individual λ-DNA molecules. We observe distinct current blockage signatures of single and multiply folded DNA molecules as they undergo voltage-driven translocation through the glass nanopores. We find increased signal to noise for single molecule detection for higher trans-nanopore driving voltages.

cited By (since 1996) 5; International audience; The active cooling of the Supersonic Combustion Ramjet engine, for hypersonic flight purpose, is ensured thanks to fuel, n-dodecane for the present study. The endothermic fuel pyrolysis, starting above 800 K, could generate an unwanted coke formation. Experimental tests up to 1125 K and between 1 MPa and 6 MPa have been performed on the hydrocarbon fuel pyrolysis to evaluate the coking activity. 316L stainless steel, low carbon steel and titanium reactors have been considered. A witness of the coke formation, based on its thermal insulation and pressure loss effects, has been found. A correlation between methane production and coke deposit was found. The coke has been studied with Scanning Electron Microscope (SEM), Energy Dispersion Spectroscopy (EDS), X-ray diffractometer and Fourier Transform Infrared (FTIR) spectroscopy. The porosity, the density and the permeability of the coke have been estimated. © 2008 Elsevier B.V. All rights reserved.

Scanning Electron Microscope (SEM) as one of the major research and industrial equipment for imaging of micro-scale samples and surfaces has gained extensive attention from its emerge. However, the acquired micrographs still remain two-dimensional (2D). In the current work a novel and highly accurate approach is proposed to recover the hidden third-dimension by use of multi-view image acquisition of the microscopic samples combined with pre/post-processing steps including sparse feature-based stereo rectification, nonlocal-based optical flow estimation for dense matching and finally depth estimation. Employing the proposed approach, three-dimensional (3D) reconstructions of highly complex microscopic samples were achieved to facilitate the interpretation of topology and geometry of surface/shape attributes of the samples. As a byproduct of the proposed approach, high-definition 3D printed models of the samples can be generated as a tangible means of physical understanding. Extensive comparisons with the state-of-the-art reveal the strength and superiority of the proposed method in uncovering the details of the highly complex microscopic samples.

The objective of this study was to improve the stability and water-solubility of patchouli alcohol by complexing with β-cyclodextrin (β-CD). The interactions between patchouli alcohol and β-CD were characterized by differential scanning calorimetry (DSC), Fourier transformation-infrared (FT-IR) spectroscopy, powder X-ray diffraction (PXRD), and Scanning electron microscope (SEM), respectively. According to molecular modeling method, the enthalpy formation of host-guest illustrated the predominant configuration and the lowest value ΔbGo was -10.8174±1.9235 kcal/mol, suggesting the complex could reduce the energy of the system. The characterization analysis confirmed the formation of PA-CD inclusion complex, and the results indicated the advantage of the inclusion complex in stability and dissolution rates. These results identified PA-CD inclusion complex an effective way for the storage of PA, and better inclusion method still needed to be studied.

International audience; Nanometric spheres of an azopolymer are obtained by micellization from a solution. We observe photoinduced deformation of the individual nanospheres under white light illumination. The diameter expands up to 35% parallel to the substrate surface. The magnitude of the force that is necessary to produce the same effect is estimated.