Search

WOS:000967659000009 The utilization of plant extraction products from Oeneanthe pimpinelloides (Apiaceae family) seeds were investigated in terms of their use as an insecticide control of packaging materials. The aim was to investigate their insecticidal effects against the flour beetle Tribolium castaneum. The Oeneanthe pimpinelloides seeds were extracted with methanol. By using the liquid-liquid extraction method, the hexane extract (II) was separated from the methanol extract (I) and hexane and methanol were evaporated. Then, the chemical composition of each sample was determined via gas chromatography–mass spectrometry. The methanol extract predominantly contained tetrahydrofuran, 1-methoxy-2-propanol, 1-methoxy, 2-butoxyethanol, 1-phenylethanone, cyclohexene carboxylate derivative, (3-phenyl-2-propynylidene) cyclopropane, diphenyldiazene, and dihydroxypropyl ester components, while the hexane fraction contained nonane, 1-octanol, decane, undecane, tridecane, alkyl benzene, benzene sulfonic acid, benzoxazine, and hexadecanoic acid components, as well as some derivatives of them. Each fraction was dissolved in DMSO for impregnation on filter paper. The insecticide effects of the paper samples were determined against Tribolium castneum. According to the results, the mortality started after 3 d for each fraction. After 4 d, the hexane fraction indicated total mortality in comparison with the methanol fraction, which showed partial mortality (3/5).

From the end of the nineteenth century and one hundred years onward, home sewing was an important part of many women’s duties, but it was also a pleasure, something that existed parallel with the emerging mass-produced ready-to-wear industry. The paper patterns used for home dressmaking were often sold and distributed through women’s magazines. These pattern sections were both a kind of reader service and a conscious strategy to capture the female target group. This article, based on an analysis of three Swedish magazines, is the first in-depth survey of patterns for home sewing of women’s clothes in Sweden. The study shows how the magazines adapted to changes in society with increasingly easier patterns and ready-cut fabric for their readers. By highlighting women making their clothes in the home, this article contributes to an often-neglected area of women’s memory and fashion history.

Currently, tissue product producers try to meet consumers’ requirements to retain their loyalty. In perforated products, such as toilet paper, these requirements involve the paper being portioned along the perforation line and not outside of it. Thus, it becomes necessary to enhance the behavior of the perforation line in perforated tissue papers. The current study aimed to verify if the perforation line for 0° (the solution found in commercial perforated products) is the best solution to maximize the perforation efficiency. A finite element (FE) simulation was used to validate the experimental data, where the deviations from the experiments were 5.2% for the case with a 4 mm perforation length and 8.8% for a perforation of 2 mm, and optimize the perforation efficiency using the genetic algorithm while considering two different cases. In the first case, the blank distance and the perforation line angle were varied, with the best configuration being achieved with a blank distance of 0.1 mm and an inclination angle of 0.56°. For the second case, the blank distance was fixed to 1.0 mm and the only variable to be optimized was the inclination angle of the perforation line. It was found that the best angle inclination was 0.67°. In both cases, it was verified that a slight inclination in the perforation line will favor partitioning and therefore the perforation efficiency.

Lead (Pb) pollution from local mines and industrial use increases risks for human, animal, and plant health. Pectin is an effective chelator of Pb, and it has been shown that a unicellular green alga, Penium margaritaceum, synthesizes pectin in the cell wall. In this study, the ability of P. margaritaceum to remove Pb from an aqueous solution was investigated. Energy dispersive X-ray spectroscopy revealed that two strains of P. margaritaceum accumulated Pb on the cell surface. Hence, P. margaritaceum cells were immobilized on cellulose filter paper. The immobilized algal cells were soaked in 1.0 mg/L Pb solution with gentle shaking for 8 h, and Pb in the solution and on the filter paper was measured by flame atomic absorption spectrometry. The immobilized algal cells continuously decreased the Pb concentration to less than 0.5 mg/L and recovered 31.8–32.7% of added Pb. The specific decrease in Pb and increase in Ca were observed in the presence of 1.0 mg/L each of Ca, Mg, Na, and K. Fourier transform infrared spectra suggested that the carboxylic acid group would be responsible for the adsorption of Pb. This study is the first to demonstrate the effectiveness of the immobilized P. margaritaceum cell in removing Pb from aqueous solutions with simple solid–liquid separation.

Microfluidic paper-based analytical devices (μPADs) are emerging as powerful analytical platforms in clinical diagnostics, food safety, and environmental protection because of their low cost and favorable substrate properties for biosensing. However, the existing top-down fabrication methods of paper-based chips suffer from low resolution (200 μm). Additionally, papers have limitations in their physical properties (e.g., thickness, transmittance, and mechanical flexibility). Here, we demonstrate a bottom-up approach for the rapid fabrication of heterogeneously controlled paper-based chip arrays. We simply print a wax-patterned microchip with wettability contrasts, enabling automatic and selective assembly of cellulose microfibers to construct predefined paper-based microchip arrays with controllable thickness. This paper-based microchip printing technology is feasible for various substrate materials ranging from inorganic glass to organic polymers, providing a versatile platform for the full range of applications including transparent devices and flexible health monitoring. Our bottom-up printing technology using cellulose microfibers as the starting material provides a lateral resolution down to 42 ± 3 μm and achieves the narrowest channel barrier down to 33 ± 2 μm. As a proof-of-concept demonstration, a flexible paper-based glucose monitor is built for human health care, requiring only 0.3 μL of sample for testing.

This work was developed within the scope of project i3N (LA/P/0037/2020. I.P. N. F. Santos thanks i3N for the BPD Grant BPD/UI96/5177/2020. S. O. Pereira thanks i3N for the BPD Grant BPD/UI96/5808/2017. The authors also thank Jonas Deuermeier for the XPS measurements. Publisher Copyright: © 2022 Elsevier Ltd Laser-induced graphene from paper (paper-LIG) was applied in non-enzymatic electrochemical sensing of uric acid (UA) in human urine. Paper-LIG was formed by CO2 laser modification of paper into a 3D graphene arrangement. Kinetic analysis of paper-LIG electrodes returned effective heterogeneous electron transfer standard rate constants of 1.4 × 10−3 cm s−1 and 7.8 × 10−4 cm s−1 for [Ru(NH3)6]2+/3+ and [Fe(CN)6]4−/3− redox probes, respectively. These electrodes were able to detect and quantify uric acid in PBS within the 10–300 μM range at pH between 5.6 and 7.4. At pH 7.4, a linear response (R2 = 0.999) from 10 to 250 μM was achieved, with a limit of detection of 3.97 μM and a sensitivity of 0.363 μA cm−2 μM−1. Paper-LIG electrodes denoted adequate selectivity in synthetic urine as well as in ascorbic acid (AA) and dopamine (DA)-containing electrolytes. Determination of urinary UA content in human samples returned a concentration of c.a. 1.8–1.9 mM, within the range for healthy individuals. Recoveries of samples spiked with 50 and 100 μM UA were 100.6% and 95.4%, respectively, with satisfactory reproducibility and stability. These cheap, lightweight, flexible, and eco-friendly paper-LIG biosensors for non-enzymatic quantification of UA in human urine pave the way to widespread application in the detection of other important biomarkers. publishersversion published

Pseudoestrogene bisphenol A (BPA) can be important ingredient of thermochromic inks, increasingly used materials in thermal printing paper, security printing, advertising, design and as temperature indicators in medicine and food industry. BPA mass fraction in thermochromic inks can be up to several percent. Hence, disposal of items with thermochromic prints pose a risk of environmental pollution. In this work BPA mass fraction was monitored during anaerobic degradation of papers with thermochromic prints in soil in both matrices: papers and soil. The degradation conditions simulated deeper layers of waste at a landfill site. Six types of papers with prints of thermochromic ink containing 2% of BPA were subjected to anaerobic degradation over up to 150 days.

Oil media on paper, such as oil paintings, sketches, prints, and books, occasionally present problems associated with the effect of oil medium on the paper support, raising a composite matter of condition assessment as it depends on several factors. The present work examines the effect of linseed oil on paper and, in particular, the changes caused by three types of linseed oil on the optical, morphological, mechanical, and chemical properties of pure cellulosic paper, employing mock-ups submitted to artificial ageing in controlled conditions of relative humidity and temperature in airtight vessels. The study involved colorimetry, opacity, tensile strength, pH measurements, SEM, FTIR, and VOC analysis with GC-MS. Processing of the results has so far indicated that thermal-humid ageing caused the gradual darkening of the oil-impregnated mock-ups, as well as alterations in opacity, intense fall of pH values, and severe reductions in tensile strength, while linseed oil processing during manufacture has a significant impact. FTIR spectra have indicated that chemical changes upon ageing are in accordance with those of optical and mechanical changes, while VOC emissions are mostly associated with the drying and degradation of the different types of linseed oil.

The current data on climate change and environmental degradation are dramatic. The consequences of these changes are already having a significant impact on people's health. Physicians - as advocates of the patients, but also as citizens - have an ethical obligation to be involved in efforts to stop these changes. The European Federation of Internal Medicine (EFIM) strongly encourages the Internal Medicine societies and internists across Europe to play an active role in matters related to climate change and environmental degradation. At a national level, this includes advocating the adoption of measures that reduce greenhouse gas (GHG) emissions and environmental degradation and contributing to policy decisions related to these issues. At a hospital level and in clinical practice, supporting actions by the health sector to reduce its ecological footprint is vital. At the level of EFIM and its associated internal societies, promoting educational activities and developing a toolkit to prepare internists to better care for citizens who suffer from the consequences of climate change. In addition to advocating and implementing effective actions to reduce the ecological footprint of the health industry, recommending the introduction of these themes in scientific programs of Internal Medicine meetings and congresses and the pre- and postgraduate medical training. At a personal level, internists must be active agents in advocating sustainable practices for the environment, increasing the awareness of the community about the health risks of climate change and environmental degradation, and being role models in the adoption of environmentally friendly behaviour.

Flexible inkjet-printed antenna is presented. The proposed antenna is designed on a synthetic paper substrate with an area of 35 × 40 mm2 to provide frequency bands for many popular wireless applications. Simulation and measurement are used to study the performances, including the frequency bands, radiation patterns, peak gains and efficiency, of the antenna in two severely bending conditions with a curvature radius of 20 mm in the forward and backward directions. The antenna printed in photo papers material could not be fully flexible due to cracks introduced to the coating material on the surface of the photo paper. Hence, the resin coated material was only suitable for curved devices. The synthetic paper material used in this paper does not have a resin coating, therefore, the antenna does not lose its flexibility and can be bent in both the forward and backward directions without any cracks. Results show that bending in these two conditions has insignificant effects on the performances of the antenna. With a curvature radius of 20 mm in the forward direction, the measured peak gain and efficiency of the antenna are in the ranges from −3 to +2 dBi and 40% to 60%, respectively. The results together with the low cost make the antenna most suitable for many flexible 5G communications devices.

Publisher Copyright: © 2022, The Author(s). Direct fire, indirect heat, and extinguishing water cause great damage to cultural assets upon a fire disaster in a library or archive. Conservation and restoration of heat-damaged papers are particularly challenging due to the complexity and severity of the damage. Since valuable originals obviously cannot be used for the development of treatment methods and only to a limited extent for the analysis of the damage, it is necessary to produce model paper materials that have a high degree of similarity to fire-damaged papers, which was addressed in the present study. Three different heating methods were tested to produce model papers of different heating levels. Their altered optical, structural, and chemical properties were analyzed and compared with the results of original fire-damaged samples. The study points out pathways to enable the production of comparable sample materials. Heating between hot plates or in an oven produces papers that have properties quite similar to the originals in terms of surface area, paper structure, cellulose integrity, and interactions with water. Stack heating in the oven has proven to be a particularly effective manufacturing method for larger quantities of model papers.

This work presents a unique approach to the design, fabrication, and characterization of paper-based origami robotic systems consisting of stackable pneumatic actuators. These paper-based actuators (PBAs) use materials with high elastic modulus-to-mass ratios, accordion-like structures, and direct coupling with pneumatic pressure for extension and bending. The study contributes to the scientific and engineering understanding of foldable components under applied pneumatic pressure by constructing stretchable and flexible structures with intrinsically nonstretchable materials. Experiments showed that a PBA possesses a power-to-mass ratio greater than 80 W/kg, which is more than four times that of human muscle. This work also illustrates the stackability and functionality of PBAs by two prototypes: a parallel manipulator and a legged locomotor. The manipulator consisting of an array of PBAs can bend in a specific direction with the corresponding actuator inflated. In addition, the stacked actuators in the manipulator can rotate in opposite directions to compensate for relative rotation at the ends of each actuator to work in parallel and manipulate the platform. The locomotor rotates the PBAs to apply and release contact between the feet and the ground. Furthermore, a numerical model developed in this work predicts the mechanical performance of these inflatable actuators as a function of dimensional specifications and folding patterns. Overall, we use stacked origami actuators to implement functionalities of manipulation, gripping, and locomotion as conventional robotic systems. Future origami robots made of paper-like materials may be suitable for single use in contaminated or unstructured environments or low-cost educational materials.

Food safety is an issue that cannot be ignored at any time because of the great impact of food contaminants on people's daily life, social production, and the economy. Because of the extensive demand for high-quality food, it is necessary to develop rapid, reliable, and efficient devices for food contaminant detection. Microfluidic paper-based analytical devices (μPADs) have been applied in a variety of detection fields owing to the advantages of low-cost, ease of handling, and portability. This review systematically discusses the latest progress of μPADs, including the fundamentals of fabrication as well as applications in the detection of chemical and biological hazards in foods, hoping to provide suitable screening strategies for contaminants in foods and accelerating the technology transformation of μPADs from the lab into the field.

The International Conference on Cognitive Modeling brings together researchers from around the world whose main goal is to build computational systems that reflect the internal processes of the mind. In this issue, we present the five best representative papers on this work from our 19th meeting, ICCM 2021, which was held virtually from July 3 to July 9, 2021. Three of these papers provide new techniques for refining computational models, giving better methods for taking empirical data and producing accurate computational models of the cognitive systems that produce them. The other two papers focus on explanation: using models to elucidate the underlying processes affecting cognition in such diverse domains as logical reasoning and the effects of caffeine.

Microfibrillated cellulose (MFC) was prepared from post-consumer old corrugated container (OCC) material, which was first disintegrated in water, cleaned to remove impurities, and then fibrillated by grinding. Those processed MFCs were treated with in-situ formation of calcium carbonate by adding calcium oxide and injecting carbon dioxide into the mixture up to the ratio of 1:40 (MFC : calcium carbonate) by weight. The MFCs had a dark brown color initially but turned into high brightness materials similar to commercial ground calcium carbonate (GCC) after the in-situ formation process. The MFCs that had calcium carbonate attached on their surfaces, which were lengthy and flexible, were called flexible calcium carbonate from OCC (FCCO). Paper containing FCCO gave higher bulk, higher stiffness, and higher tensile index without lowering smoothness when compared to the paper containing commercial GCC. However, brightness was slightly lowered because of initial low brightness of the OCC. This study also demonstrated the feasibility to substitute wood fibers up to 5% with FCCO without lowering essential properties for printing paper. Benefits of the waste paper are savings of both wood resources and production cost.

Selective detection and quantification of biomarkers related to human diseases are essential for preventive healthcare. Surface-enhanced Raman scattering (SERS) spectroscopy is a powerful analytical tool offering high sensitivity. However, the success of this promising analytical tool relies on the ability to effectively fabricate SERS substrate. Herein we have demonstrated a plasmonic paper-based flexible substrate (PPFS) for SERS sensing. In situ growth of silver nanostructures (AgNS) on the paper-based substrate was achieved by using a simple one-step silver mirror reaction (SMR). FESEM and TEM results depicts that the increasing silver ion content influences the morphology (growth of multifacets), as well as size of AgNS. Further, the PPFS substrate was tested with Rhodamine-6G (Rh-6G) dye and an attomole sensitivity with a LOD of 4.54 x 10-18 M was achieved. Further, two biomarkers, lactic acid (LA) and uric acid (UA) were detected on the PPFS substrate, with μM and pM sensitivity, having LOD values of 0.6 x 10-6 and 0.3 x 10-12 M respectively. Above detection levels for UA on PPFS is two orders better than reported values, whereas for LA it is comparable with reported substrates. Finally, UA, LA and their mixtures were tested on PPFS and results compared with commercial substrate. The performance of PPFS were found better in all cases, thus, multifaceted AgNS paper based PPFS offers the potential to be used as a biosensor for detection of various biomarkers from body fluids, responsible for the detection of the critical disease for preventive health care.

Statement of problem Quick response (QR) codes are a fast and efficient technology for linking and accessing identifying information, and their use has been proposed in forensics. The heat resistance and esthetics of denture marking methods (DMMs) have been recommended by the American Dental Association (ADA), but studies on these aspects of printed QR codes are lacking. Purpose The purpose of this study was to determine the optimal printed material with QR codes for implementation as a DMM adjusted to the recommendations of the ADA. Material and methods The behavior of 4 types of paper, bond paper, fiberglass filter paper, ultralong hydroxyapatite nanowire paper, and polyolefin and silica paper with printed QR codes was analyzed. They were exposed to temperatures between 100 °C and 1000 °C in a heat muffle for 1 hour. Each specimen was subjected to both a morphological and a thermogravimetric analysis (TGA) and scanned by using 3 different smartphones. Results The scans were positive for bond paper (33.3%), fiberglass fiber paper (50%), ultralong hydroxyapatite nanowire paper (100%), and polyolefin and silica paper (70.4%). The TGA revealed continuous decomposition curves (average 16.5 minutes at 624 °C). Conclusions Printed QR codes on ultralong hydroxyapatite nanowire paper appear to be suitable as information reservoirs, even surviving incineration, and may be implemented as a DMM conforming to the ADA recommendations.

Microfluidic paper-based analytical devices (μPADs) are emerging as prominent platform for disease detection, specifically in developing countries. This paper device offers simplicity and affordability not typically seen in centralized laboratory settings. However, detection limits in μPADs are inadequate and often require tests results to be read within a specific time interval to ensure accuracy. To overcome these challenges, we are developing an on-chip mass spectrometry (MS) detection strategy for immunoassays performed on paper substrates. Herein, we present our initial results from a proof-of-concept study toward the development of μPADs capable of storing immunoassay reagents within the confinements of the 3D device, automatic splitting of biofluid into four individual test zones, immuno-capture of disease biomarker, and on-chip MS detection of captured species. The reported study encourages the development of point-of-care and direct-to-customer testing using the disposable μPAD to collect samples, followed by sensitive analysis using portable mass spectrometers. We demonstrate this capability using malaria Plasmodium falciparum histidine-rich protein 2 (PfHRP2) antigen detection.

In recent decades, there has been a growing interest in the recycling of organic materials such as paper mill biosolids (PB) and biochar for use as soil amendments. However, the benefits of co-application of PB and biochar and its effects on soil phosphorus (P) availability remain unknown. An incubation study was conducted on two acidic soils to assess the effect of two PB types (2.5% w/w) co-applied with three rates (0%, 2.5%, and 5% w/w) of pine (Pinus strobus L.) biochar on soil P fractions. An unfertilized control and a mineral NP fertilizer were used as a reference. Soil P fractions were determined by Hedley procedure after 2 and 16 wk of incubation. Material fractionation indicated that the PB containing the highest total P and the lowest Al content had the highest proportion of labile P, whereas most P in the biochar was in a stable form. The incubation study revealed that the P-rich PB increased P availability in both soils to a level comparable to mineral fertilizer at the end of the incubation. The addition of biochar to PB, however, did not affect soil P availability, but the highest rate induced a conversion of P fixed to Al and Fe oxides towards recalcitrant forms, particularly in the sandy loam soil. We conclude that co-applying biochar and PB could be more beneficial than application biochar alone and soils amended with such a mixture would be expected to release part of their P slowly over a longer period of time.