Search

The paper provides a comparative analysis of the influence of ring concentrator shape in ultrasonic systems on their amplitude-frequency characteristics. Devices are known in which elastic elements are used either as resonators or as working tools of ultrasonic technological systems. However, the use of elastic elements as concentrators of ultrasonic vibrations is insufficiently studied and requires comprehensive research and development of recommendations for their practical application. For this purpose, a theoretical analysis has been carried out in the paper while using the ANSYS computer program, which made it possible to perform modal and harmonic analysis of ring models with various shapes. The round ring has a nominal outer diameter of 50 mm and a variable cross-section. Three ring models have been analyzed: one round model and two models of oval shape. To conduct a comparative analysis and identify frequencies at which resonance occurs, the vibration characteristics of the rings have been considered in the frequency range from 1 to 26 kHz. Results of the analysis show that, depending on the frequency of forced vibrations, bending vibrations are formed in the rings, which act in different coordinate planes. In this case, a change in the shape of the rings is accompanied by a change in the amplitude of the bending vibrations. The most intense ring vibrations along the vertical axis have been achieved in circular rings. It has been found that with an increase in the frequency of forced oscillations, an increase in the number of oscillation periods is observed. If in the region of low vibration frequencies only a one-period vibration mode is formed in the ring, then in the region of ultrasonic vibrations the number of vibration periods increases to two and three. All the considered ring models have several natural vibration frequencies with a certain periodicity in different coordinate planes depending on the shape of the rings. The intensity of the vibrations is different in different directions and depends on the shape and frequency of the forced vibrations. Examples of vibration mode variations for various ring shapes are demonstrated in the paper.

The purpose of this paper is a spectrum analysis of signals of various nature, construction of the signal scalogram using Morlet wavelet, modification of the scalogram to obtain a more informative graphic representation of the signal. Spectral analysis of the signal is constructed by means of the Fourier transform. A modification of the graphical representation of the result of the wavelet transform has been developed with the help of the Mathematica system. For this, a wavelet scalogram has been used as a two-dimensional representation of the original signal. A scale has been introduced on it for the value of the signal amplitude depending on the time and period of its constituent components. This graphical representation allows us to obtain additional information about the dynamic properties of the original signal. A modification of the representation of the original signal scalogram has been developed for a more complete spectrum analysis (determination of the period of the constituent components). The paper contains an example using a modified scalogram for the analysis of a signal containing two pulses, an audio signal and white noise. The basic wavelet in this case is the Morlet wavelet. A comparison of the scalogram, obtained using the built-in function, and the modified scalogram has been made in the paper. The disadvantage of the first scalogram is the impossibility of assessing the frequency of the signal; its advantage is the ability to assess the localization of the pulse. For a modified scalogram, the advantage is the estimation of the signal periodicity, and the disadvantage is the inaccuracy in determining the range of pulse localization. For spectrum analysis in Mathematica, it is recommended to use a combination of two approaches (using a standard built-in function to determine the localization of the pulse) and a modified scalogram (to determine the periods of the constituent components).

The bilinear programming problem is considered, where a column, which corresponds to one of the variables, is not fixed but can be chosen from a convex set. This problem is known as the Dantzig – Wolfe problem. Earlier, a modified support method was proposed to solve the problem, using the decomposition of the problem constraints of the Dantzig – Wolfe method. The author of the paper has developed a direct exact method for solving the formulated problem. The method is based on the idea of the solving a linear programming problem with generalized direct constraints and a general concept of an adaptive solution method. The notions of support, support plan, optimal and suboptimal (e-optimal) plan are introduced which is a given approximation of the objective function to the optimal plan of the problem. Criteria for optimality and suboptimality of the support plan have been formulated and have been proved in the paper. The search for the optimal solution is based on the idea of maximizing the increment of the objective function. This approach allows more fully to take into account the main target and structure of the problem. Improving a support plan consists of two parts: replacing the plan and replacing the support. To find a suitable direction, a special derived problem is solved while taking into account the main constraints of the problem. The replacement of the support is based on the search for the optimal plan of the dual problem. The method leads to an optimal solution to the problem in a finite number of iterations (in the case of a non-degenerate value).

Objective. The purpose of the research is to develop and implement a Telegram bot for effective task management using the functionality of the Telegram API. Method. The study is based on database design techniques. Result.The paper describes the process of developing and optimizing a Telegram bot for effective task management. As part of the research, an application was developed, implemented in Python using the Telegram API and using the PostgreSQL DBMS to store data as part of the workflow. The system is designed to optimize the workflow, manage tasks in the system and delegate them to users. A database has been designed, where the structure and relationships between data are defined, ensuring efficient storage and access to information, taking into account the needs of the application. Conclusion.The phased implementation of functionality, from task management, user notification systems, to data processing and analysis, allows us to obtain a fully functional system with a wide range of capabilities. To clarify the functions and capabilities of the bot, a demonstration of the application was carried out, reflecting the functionality of the system.

Poorly designed business process models are a source of errors and the subsequent costs associated with these errors, such as monetary costs, lost time, or even some harmful impact on people or the environment if the erroneous business process models are associated with critical industries. The BPM (Business Process Management) lifecycle usually consists of designing, implementing, monitoring, and controlling the business process execution, but it lacks continuous quality control of the created BPMN (Business Process Model and Notation) models. Thus, this paper considers the problem of business process models classification based on their correctness, which solution will ensure quality control of the designed business process models. Thus, this study aims to improve the quality of business process models by developing a software solution for business process models classification based on their correctness. The subject of the study is the process of business process models classification based on their correctness, which uses quality measures and thresholds, usually, complexity measures. The subject of the study is a software solution for business process models classification based on their correctness. Therefore, in this study, the algorithm to solve the problem of BPMN models classification using logistic regression, interface complexity, and modularity measures is proposed, the software requirements are determined, the software development tools are selected, the software for business process models classification based on their correctness is designed, the corresponding software components are developed, the use of a software solution for solving the problem of business process models classification based on their correctness is demonstrated, the obtained results are analyzed and discussed. The developed software indicates high performance of BPMN models classification based on their correctness, achieving high accuracy (99.14 %), precision (99.88 %), recall (99.23 %), and F-score (99.56 %), highlighting the high performance of modeling errors detection.

The only right strategy for businesses and government organizations in Ukraine and other countries that may face aggression is to recognize themselves as a potential target for cyberattacks by the aggressor (both by its government agencies and related cybercriminal groups) and take appropriate measures in accordance with the European Union’s General Data Protection Regulation (GDPR). The main purpose of the GDPR is to regulate the rights to personal data protection and to protect EU citizens from data leaks and breaches of confidentiality, which is especially important in today’s digital world, where the processing and exchange of personal data are integral parts of almost every business process. Therefore, the GDPR encourages organizations to transform their day-to-day business processes that are involved in managing, storing, and sharing customers’ personal data during execution. Thus, business process models created in accordance with the GDPR regulations must be of high quality, just like any other business process models, and the probability of errors in them must be minimal. This is especially important with regard to the observance of human rights to personal data protection, since low-quality models can become sources of errors, which, in turn, can lead to a breach of confidentiality and data leakage of business process participants. This paper analyzes recent research and publications, proposes a method for analyzing business process models that ensure compliance with the GDPR regulations, and tests its performance based on the analysis of BPMN models of business processes for obtaining consent to data processing and withdrawal of consent to user data processing. As a result, the probability of errors in the considered business process models was obtained, which suggests the possibility of confidentiality violations and data leaks of the participants of the considered business processes associated with these errors, and appropriate recommendations were made.

Copyright of Cybernetics & Systems Analysis / Kibernetiki i Sistemnyj Analiz is the property of V.M. Glushkov Institute of Cybernetics of NAS of Ukraine and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Electronic Processing of Materials / Elektronnaya Obrabotka Materialov is the property of Institute of Applied Physics and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Stratum Plus Journal is the property of P.P. Stratum plus and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Radio Electronics, Computer Science, Control is the property of Zaporizhzhia National Technical University and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Galician economic journal is the property of Ternopil Ivan Puluj National Technical University and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

The paper presents main trends in growth and generation of waste, depending on increase of world GDP and the population of the planet. The main directions in extending the concept of national strategies for sustainable development have been considered with due account of energy and resource conservation problems, as well as the need for the rational use of natural and secondary resources in all countries of the world community. The energy potential use of combustible waste that has not found technological application is considered by many countries as one of the priority areas in the field of unconventional energy. The paper describes the main directions in application of the technology for briquetting multicomponent compositions into solid fuel. The developed production technology makes it possible to process waste products by briquetting them with the addition of various binders, and on the example of a binder component in the form of viscous hydrocarbon-containing waste, the main technological features of obtaining solid multicomponent fuel are presented in the paper. The paper describes the equipment for electrohydraulic treatment, which operates as a part of the preparation line for briquetting of the applied oily waste and that allows to reduce the sulphur content in the waste used, and such approach in general permits to regulate the environmental characteristics of harmful substance emissions at the maximum acceptable level. Taking into account the application aspects of the technology for wet briquetting of materials, the paper reflects the main results of the obtained dependences of humidity on productivity according to the content of the binder component. The proposed algorithm for solving the problem makes it possible to rationally use of substandard combustible industrial waste to obtain a multicomponent solid fuel, while at the production stage, the energy and environmental aspects of the resulting fuel are taken into account with due consideration of the component composition of the fuel.

The paper considers an issue of transition to digital management technologies in the field of construction and housing and communal services in Russia, as well as in other countries. An optimization methodology for the application of the digital economy has been developed using the example of the existing real estate management system in the Stolichny Microdistrict of Izhevsk city (Udmurt Republic, Russian Federation). The existing and developed new projects of digital technologies are described, the introduction of which will increase the efficiency of the construction and operation of residential buildings. A methodology has been formed for creating an optimization mathematical model for managing construction and operation projects of energy-efficient residential buildings. Prerequisites and a scheme for the joint implementation of this model and digital technologies are given to improve the quality of construction and operation of residential buildings. The paper proposes a phased methodology for the introduction of digital technologies in urban planning, as well as in the field of housing and communal services within the framework of the national program “Digital Economy of the Russian Federation”. The advantages of using block-chain technology in the management of projects for the construction and operation of energy-efficient residential buildings have been studied in the paper. The application of the developed methods that meet the needs of participants in construction activities, as well as the housing and utilities sector, will improve the efficiency of not only the management system for the construction and operation of energy-efficient residential buildings, but also the overall effectiveness of the introduction of digital management in real estate. The proposed ABRIS software can be used in housing and communal services to optimize and track the expenditure of resources vital for a comfortable living of the population.

The reform of the energy sector in the Republic of Belarus, which in the last few years has moved to the stage of active implementation, will bring significant changes in the management of energy enterprises. The introduction of risk management for energy enterprises will become a necessary stage, which is justified by the transition of the energy sector to market relations. In this regard, it is necessary to consider the main issues of risk assessment for energy enterprises. The paper proposes a method for qualitative and quantitative analysis of all the risks that an energy enterprise may face in the process of energy generation. The approaches of various authors to the algorithm of qualitative risk analysis have been considered in the paper. This has made it possible to clarify the main tasks that need to be solved when conducting a qualitative risk analysis. The paper also presents an analysis of methods for quantitative risk analysis. The most commonly used methods include scenario analysis and mathematical statistics, analogy and analytical methods, methods for assessing losses, expert assessments and the theory of statistical games. Each of these methods has its own advantages and disadvantages. The performed analysis of quantitative risks has permitted to substantiate the choice of methods applicable to the energy sector, taking into account the specificity of activity type. The paper has studied various scales for estimating the probability and possible losses from risks. A comparative analysis of these scales is presented and the choice of a scale for energy enterprises is justified in the paper. Attention has been paid to the problem of probability classification pertaining to occurrence of risk events. The methodology for determining the value of possible losses when performing a risk event has been considered in detail. Potential losses are classified into the following groups: interruptions in the technological process, consequences for people, environmental consequences. Possible financial losses, as well as losses from the position of the law and reputation, have been considered separately. A critical review of risk management methods has been performed in the paper. The paper has identified the most promising methods of risk management for energy enterprises

The object of the study is durability of expansion joints in bridge structures; the subject of the research is the vibration response of a structure obtained under conditions of natural operation. Diagnostics of the road bridge expansion joints has been carried out in order to identify characteristic dependences between the value of structure vibration response and types of expansion joint designs during the period of their operation while taking into account the features of the bridge structure. For this purpose, we have tested the methodology for collecting and processing data on the vibration response of the structure under natural conditions of its operation. The paper presents results of data collection on the coverage topology which have been obtained while using three-dimensional scanning method. Data collection on the vibration response of the structure has been carried out by measuring the vibration velocity and deformation of the structure. The data obtained are analyzed. As a result of testing and analysis of the obtained data, the main characteristics have been revealed: the value of base unevenness, the amplitude of vibration velocity and vibration displacement of the structure elements. Two main parameters of the dynamic impact have been assigned, adjusted for the mass of a moving vehicle, which can be used as main parameter for assessing the magnitude of the dynamic impact. A comprehensive method for assessing the dynamic impact on bridge structures has been developed and proposed in the paper, and its use will make it possible to differentiate various designs of expansion joints according to the magnitude of the dynamic impact of vehicles. This, in its turn, will contribute to formulate new recommendations on the use of specific types of expansion joints for various categories of highway, which will increase operational durability of expansion joints and the structure as a whole.

The article considers the problems of reducing the quality of aviation products, leading to the loss of competitiveness of finished products and an increase in cost price. In the course of the study, the authors analysed the reasons for the appearance of defective products at an aviation manufacturing enterprise. Based on the information received using modern data processing methods, the paper determines the main weaknesses of the considered technological stage of aviation products. Having studied modern international quality standards in the field of aviation construction, the authors proposed measures that would reduce the number of defective products and increase the reliability and competitiveness of finished products. The article presents separately the model for evaluating the effectiveness of measures to reduce the defectiveness of aviation products. The paper carries out assessment of the proposed tactical measures to reduce the level of defective products, which will increase the economic performance of production activities in certain areas of production.

New two-layer wear-resistant coatings of the composite type “thermal diffusion layer – vacuum ion-plasma coating TiAlN” have been obtained, their durometric and tribological properties have been investigated in the paper. The study has made it possible to establish influence of preliminary thermochemical treatment of a steel substrate on the formation of surface thermal diffusion layers is significantly higher than on unhardened steel substrates. Thus, the nano-hardness of TiAlN 1 μm-thickness coatings on substrates with a carbonitride layer when indented to a depth of 0.1–0.9 μm, is 1.9 times higher, the elastic modulus is 1.7 times higher, the ductility index H/E* is higher by 13.0 %, the rate of elastic recovery H2/E* and the rate of plastic deformation resistance H3/E*2 – have been increased by more than 2.1 and 2.4 times, respectively. The fracture toughness has been increased by 4.5 times. Preliminary boriding of the steel substrate leads to an increase in the actually measured nanohardness of the coated surface up to 1.8 times, elastic modulus up to 1.8 times, H3/E*2 – up to 1.8 times, H3/E*2 – up to 1.8 times, surface hardness – up to 10.0 %, while maintaining or increasing the plasticity index H/E up to 8.0 % in comparison with the characteristics obtained by nano-indentation of the TiAlN coating on an unhardened steel substrate. The discovered phenomenon is associated with an increase in the contribution of the hardened substrate to the elastic restoration of the coating and the indentation response of the surface. The paper presents the results of practical application of the developed wear-resistant compositions.

The paper presents research on the effect of technological parameters of high-energy processing on the performance properties of powder coatings made of cermet. The use of pulse-plasma treatment is considered as an example of high-energy modification of coatings. As used powder coating materials, various versions of carbide-containing ceramics with the addition of a solid lubricant in an iron-based metal matrix have been selected in the paper. Coatings of carbide-containing ceramics with the addition of a solid lubricant in an iron-based metal matrix on are being developed to replace those of a nickel-based matrix. Such factors as crack resistance, wear resistance, workability, brittleness, as well as economic components often limit the use of powder materials based on carbide ceramics with the addition of solid lubricant in the matrix based on nickel. When only the wear process determines the service life of a part, such powder materials should be replaced with cheaper powder materials based on carbide ceramics with the addition of solid lubricant in an iron-based matrix. The proposed developments increase the wear resistance of the plasma coating due to the introduction of high-chromium steel and molybdenum into the material. Optimum porosity is formed in the initial powder mixture during the synthesis of FeCrMo–MoS2–TiC composite materials, there is an improvement in the technological parameters of powder materials, their utilization rate in plasma spraying increases, and the technology of applying wear-resistant plasma coatings becomes cheaper. The addition of the Mo element to the FeCr binder increases the wetting of titanium carbides by the binder melt during self-propagating high-temperature synthesis of the developed composite powder. Subsequent layer-by-layer processing of plasma-sprayed coatings from powders of the developed ceramics using repetitive pulses of plasma flows using different energy levels makes it possible to create strictly defined structures with necessary and controlled porosity, which decreases in a certain sequence from the outer treated layers to the base. Such treatment contributes to a significant increase in the wear resistance of the treated friction surfaces, increases the oil holding capacity, in addition, an increased adhesive and cohesive strength of the formed layers bordering the substrate is formed. Processing distances, the total number of impacts have been varied in accordance with the methodological developments, when changing the applied technological characteristics of pulse-plasma effects. The total number of plasma pulses influences on the created thickness of the plasma coating layers after treatment and contributes to the melting with compaction of the coatings obtained by the plasma treatment and the creation of a structure with hardened characteristics.

In the operation schemes of optical electronic devices (OED), such as digital autocollimators, direction finders, Shack-Hartmann sensors, as well as astro-orientation systems, projection measuring systems, geometric calibration schemes for OED, the photo-detector acts not only as a receiving device, but also as a measuring device. The tasks facing the OED photo-detectors. The solution to the problem is the use of several photo-detectors installed on one electronic board. Since OED photo-detectors act, inter alia, as measuring devices, it is necessary to perform their geometric calibration. Geometric calibration involves the measurement of interior orientation parameters used in the processing of OED images. Geometric calibration makes it possible to eliminate errors in mutual exposure of photo-detectors on one electronic board installed in the focal plane, as well as distortions introduced by the OED lens, primarily by distortion. The correctness of the interior orientation parameter determination is influenced by the relative position of the collimator, with the help of which the geometric calibration is performed, and the calibrated OED itself, i. e. the external orientation elements. The task is to separate the interior orientation parameters and the elements of external orientation. This is achieved using the method of mathematical processing of measured data in the forward and inverted positions of the collimator. This method of geometric calibration allows to use it for geometric calibration of OED with a large number of photo-detectors. The paper presents the results of the geometric calibration of the interior orientation parameters when the collimator projects a test object onto three photo-detectors of the OED layout. The factors influencing on the accuracy of the geometric calibration of the interior orientation elements for OED are determined in the paper. The developed method for geometric calibration of the interior orientation parameters for multi-matrix OED provides high measurement accuracy – not more than 0.1''–0.2''.

Nowadays there are a lot of modern technologies in electronic lexicography: speech synthesis technology, cross-referencing between dictionary modules, spell-checking functions, etc. The increasing availability of online information has necessitated intensive research in the area of automatic text summarization within the Natural Language Processing community. Belarusian scientists are also interested in this sphere and new lexicographical approaches for creating a linguistic database are shown in the paper. The authors present English-Belarusian-Russian electronic dictionary TechLex. This is the project of the 2nd English Department and the Department of Software for Information Systems and Technologies of the Belarusian National Technical University. The linguistic database of the dictionary is compiled not by the traditional method of processing a large number of paper dictionaries and combining the received translations, but by sequential processing of scientific and technical English-language periodicals. While the designing the dictionary the authors have taken into account the analysis of modern electronic multilingual translation dictionaries and created a client-server application in the Java programming language. The client part of the system contains a mobile application for the Android operating system, which has been tested on tablets and smartphones with different screen diagonals. The interface of the TechLex dictionary is designed taking into account the possibility of adding new subject areas and filling them with appropriate lexical material. The main advantage of our dictionary is that it is the first technical multilingual electronic dictionary having a Belarusian version.

Erosion is divided into two stages in accordance with the accepted design scheme for erosion of a soil dam during overflow. The paper deals with the first stage, when the downstream thrust prism is washed out. The key factor in calculating erosion deformations is the choice of the solid flow rate formula. Studies show that the mechanism of formation and transportation of solid runoff during erosion of dam models from sandy oils is very similar to that previously described by many authors for the condition of river channel erosion. The peculiarity of the process is that the erosion occurs at high speeds. Therefore, solid runoff almost immediately goes into a suspended state. To select the required formula, experiments have been carried out on models of dams made of sandy soils having various granulometric composition. It has been established that at high velocities under the considered conditions, the value of the solid waste flow rate depends solely on hydraulic characteristics of the flow. The influence of physical and mechanical properties of the eroded soil on the value of the flow rate of solid runoff is insignificant, and they may not be taken into account. Calculations have been carried out using formulas known from river hydraulics, which show that none of them gives sufficient convergence with experimental data. Based on the analysis of a large number of experimental data, a formula for the discharge of solid runoff for erosion conditions of dam models during overflow has been obtained in the paper. This has taken into account the fact that the dam erosion by the overflow has a high degree of stochasticity and is difficult to describe theoretically. This is especially evident in conditions of spatial erosion, when, simultaneously with the classical erosion of the bottom, the sides of the eroded hole periodically collapse, which is difficult to take into account in the calculations.

Metro Service has a huge impact on the development of urban transport infrastructure. The need to increase the efficiency of passenger transportation is caused by the rapid growth in passenger turnover as well as an increase in the distance from the outskirts of the city to the center. In connection with the need to develop a metro service network in Minsk city, which is confirmed by research in the area of passenger traffic in the main areas of the city, the CSM Bessac tunnel boring machine was purchased, which allows significantly to increase the speed of tunnel driving. The use of a mechanized tunnel boring machine in the traditional concept of the metro network construction, in which driving of tunnels is carried out after construction of stations, does not allow to use a shield with maximum economic efficiency due to the small extent of tunnels. There is also a need to build assembly-shield chambers and carry out works on disassembling and assembling the shield. The application of the new concept developed by Yu. S. Frolov and called “through driving” is actual in the conditions of the use of a mechanized tunnel boring machine. Its essence lies in the continuous driving of tunnels on the line section under construction and the consecutive construction of each station complex as the tunnel boring machine passes through it. To implement the concept of “through driving”, it is relevant to use a semi-closed construction method, in which the floor structure is constructed in an open way, and the other elements are closed. The available solutions of the metro stations constructed while using a semi-closed method of work have been analyzed in the paper. A detailed analysis has been carried out with due account of the adaptation to the construction conditions in Minsk, and the development of structural elements and assemblies of the platform area of the station, which is a two-cantilever vault with a developed transom part, resting on pile-columns of a circular cross section. Forces from the open ring of flexible tunnels lining are supported by a cantilever part of an arch and a bottom plate. The paper considers a design of a metro station, its main elements, their purpose and specificity of work, as well as optimization issues and the results of the design feasibility study.

The paper provides a brief review of the literature on the theory and methods of calculating hinged-connected or articulated structures on an elastic base. The author refers to the works of B. G. Korenev, G. Ya. Popov, I. A. Simvulidi, R. V. Serebryany, A. G. Yuriev, in which, using various approaches, studies have been carried out to calculate hinged-connected beams and slabs on an elastic base. From the analysis of scientific literature on the topic under consideration, it can be concluded that there is no general approach to solving this problem, which is valid for any hinged-connected beams and plates lying on any model of an elastic base under the action of an arbitrary external load. In addition, a similar problem for this type of engineering calculations is observed in the normative documents. In the Republic of Belarus, a number of industry documents have been used to calculate pavement bearing elements for various highways and track transverse structures, in which road pavements with a load-bearing element and the connection of elements between themselves (hinged or rigid) are considered in an incoherent formulation. The paper proposes a universal approach for calculating hinged-connected beams on an elastic foundation, based on the mixed method of structural mechanics, taking into account the Zhemochkin ratios for functions of the elastic medium effects. The following hypotheses and assumptions are taken into account: only normal stresses act on the contact of the beam with the base, hypotheses of the bending theory are valid for beams, hinges between the beams are cylindrical, and the distribution of contact stresses along the width of the beams is uniform. As a result of the proposed calculation, the stress-strain state of a system of hinged-connected beams on an elastic foundation has been investigated, namely: distribution of contact stresses under beams, internal forces in the beams and hinged joints, as well as settlements of the elastic foundation under them. The numerical implementation of this approach has been performed using the mathematical package Mathematica 10.4. Examples of calculation are given for different versions of hinged-connected beams and an elastic base: for three hinged-connected beams based on Winkler and seven – on an elastic half-space.

Objective. In this paper, the authors study problems of a plane strain of elastic bodies containing internal rectilinear fractures. In each case, the margins of the considered areas are supported by thin flexible coatings. The first part of the paper is devoted to the problem of an infinite elastic wedge, the faces of which are free from the outside and reinforced with a thin flexible material, and the bisector contains a rectilinear fracture with regular forces applied to the margins, and to the study of the stress concentration at the fracture vertices. In the second part of the paper, the authors consider the problem of an equilibrium radial internal fracture in the cross-section of a round pipe. The inner surface of the pipe experiences hydrostatic pressure; the outer surface is reinforced with a thin flexible coating. The purpose of the study in each of the presented tasks is to determine the values of the influence factor. Methods. Both problems are united by a single approach, in which the presence of a coating is modeled mathematically, using special marginal conditions obtained based on an asymptotic analysis of the exact solution for a strip or ring flexible coating of small relative thickness. In the first issue, the singular integral equation is derived using the Mellin transform, which allows proceeding to the solution of a system of ordinary differential equations and obtaining a singular integral equation relative to the derivative of the discontinuity function of the first kind with a Cauchy kernel. In the second issue, discontinuous solutions are constructed using the Fourier series, resulting in a singular integral equation of a similar structure. Previously, similar ideas were successfully implemented by the authors in the study of the problem of the equilibrium state of a strip with a coating weakened by an internal transverse fracture under arbitrary conditions on the lower edge of the strip. Conclusion. Singular integral equations for the considered problems are obtained. The collocation method is used to construct solutions of singular integral equations for various combinations of geometric and physical characteristics of issues. In all the considered cases, the values of the influence factor were calculated. The analysis of changes in the influence factor depending on various combinations of geometric parameters and mechanical characteristics of problems is carried out. It is noted that with increasing rigidity of the coating and increasing its thickness, the values of the influence factor decrease; the increase in the value of the influence factor is provided by approaching the fracture to the body margin and increasing its relative length.

A large variety of machine operating conditions leads to a difference in the wear rate even for their units being of the same type. Operational time terms of single-type units and machines are not the same, and therefore, numerical expressions of operational reliability will be probabilistic values. Incomplete restoration of original properties of a unit, a negligent repair, a poor maintenance usually lead to the fact that any of several parts independently one from another can determine reliability of a machine (a unit). This is especially important to consider when manufacturing packaging in order to avoid rejects. The operational reliability of modern machines consisting of hundreds, and sometimes thousands of parts, wear processes of which are in a complex relationship, depends on a number of factors. A study on reliability of main components and equipment devices is an urgent task. Successful operation of printing equipment is possible only if there is a clear organization of preventive work, ensuring preparation of printing machines for printing and post-printing processing. High-performance equipment, such as die-cutting presses, should be regularly inspected, adjusted and maintained in such a way as to obtain standard results at the output. The paper has studied reliability of main components and devices of die-cutting presses based on calculation of failure probability. Calculations have been carried out by analogy with the calculation of the probability of events in the fault tree. Failure diagrams of devices and units of die-cutting presses have been built in the paper. Based on the analysis of the failure probability for main components and devices, graphs of residual life for equipment operation on its life cycle have been constructed in the paper.

Studies on the influence of applying various technologies for combustion knock reduction have been presented in the paper. Among others, investigation concerning the following: over-expanded cycle, variable valve timing, internal and exhaust gas recirculation, leaning the combustible mixture and cooling the in-cylinder charge were of the interest. The research works were focused on impact of these technologies on both knock intensity reduction, and engine performance and toxic emissions. Results presented in the paper were coming from experimental investigation based on in-cylinder combustion pressure data acquisition. Additionally, knock intensity calculation methods were discussed. They are based on incylinder combustion pressure pulsations. Combustion knock intensity expressed by the maximum peak of the incylinder pressure pulsations shows a strong negative correlation with both the EGR ratio and relative equivalence ratio – lambda. With respect to a catalytic converter installed on the exhaust pipe line, applying EGR appears as better solution for knock reduction then leaning the combustible mixture because the catalytic converter needs stoichiometric mixture for effective NOx reduction. Furthermore, application of the over-expanded cycle to the hydrogen or coke gas fueled IC engine significantly reduces intensity of potential knock by 50 % in comparison to Otto cycle for all loads. Additionally, over-expanded cycle contributes to increase in engine thermal efficiency. Summing up, all the presented measures and technologies can be successfully implemented into practice in stationary engines as well as in traction engines, both of them working on either natural gas or gaseous renewable fuels.

An experimental assessment has been made of the influence of electro-erosive modification modes for worn working surface of an cutter on the restoration of its cutting ability. The paper provides basic information on dental cutters. The provisions of the experimental research methodology are described, including a description of a device for modifying the worn surface of a dental cutter and a device for determining its cutting ability. Experimental data are presented and analyzed that reflect an effect on restoration of a cutting ability of a worn surface of a dental cutter, voltage of a storage capacitor and number of holes applied to it during its modification. Rational modes of modifying a worn-out surface of a dental mill that provide the greatest recovery of its cutting ability have been determined in the paper. It has been shown that with increasing voltage, the energy of the electric discharge acting on the treated surface increases, which leads to the formation of a single hole of a larger size on it, including metal flows along its edge that extend beyond the initial contour of the worn cutter teeth. These metal flows on the modified surface of the cutter play the role of peculiar cutting and deforming elements. It has been revealed that in the process of modifying the worn surface of the cutter, it is necessary to ensure that there is no overlap of the holes formed on it, i.e. the distance between the centers of adjacent holes should be greater than or equal to the size of metal deposits at their edges. In this case, the metal flows retain their original shape and have the highest height at these pulse parameters, which ensures a higher cutting ability of the modified cutter surface than when the holes are overlapped.

The paper presents characteristics of the known classifications of surface shaping methods in mechanical engineering during mechanical and physical-technical processing; according to the classifications a surface shaping method is considered as a combination of methods for generating its producing lines – generatrix and guide – provided that the generation rate of the generatrix is higher than the guide. The advantages of constructing a classification and a formalized description of surface shaping methods have been shown in the paper; each of them represents a combination of surface formation methods in cross section and in length, regardless of generation speed for generatrix and guide lines. This increases information content of the description for a shaping method which is important for comparing methods of shaping surfaces and synthesis of schemes for their processing in the functional design of the machine. The paper has revealed the fact that in comparison with the well-known classification of A. A. Fedotenka it is an expedient to introduce methods of bending, intermittent track and intermittent rolling, as well as combined methods combining advantages of their basic methods which expand the synthesis of progressive processing schemes for profile surfaces. The introduction of the methods has been made in many basic methods of generating production lines (copying, following, touching and rolling). Based on the expanded set of basic methods and the accepted principle of presenting the methods of shaping profile surfaces, their classification has been developed as the basis for systematization and synthesis of known and possible shaping methods. The paper considers examples of rational shaping method synthesis based on the proposed classification and progressive processing schemes for profile moment-transmitting surfaces on the basis of synthesis examples. In particular, the use of an envelope method instead of the applied rolling method has made it possible to simplify significantly a tool design, to increase its versatility and accuracy in formation of moment-transmitting surfaces with a profile in the form of a Relo triangle.

It has been substantiated that in order to control the process of forming flat surfaces while using a free grinding method it is advisable to choose such machine setup parameters as a tool diameter and its rotation frequency, an amplitude of the reciprocating movement of the part along the tool (or vice versa) and frequency of this movement, as well as the value of the working force. Mathematical modeling of patterns for abrasive processing of flat surfaces in the conditions of free grinding on lever machines has been carried out in the paper. A formula has been obtained for calculating a sliding speed at selected reference points on the surface to be treated while taking into account the pressure in their vicinity. Patterns of the part operation have been determined, for which a correct plate is used in the proposed axicon production technology with due account of the combination and size of the selected setup parameters for processing equipment. Self-organization of the processing process has been substantiated while using a free grinding method. Sensitivity of a kinematic response to a change in processing modes and efficiency of these modes in terms of process performance have been determined in the paper. It has been noted that an increase in a tool diameter, as one of the effective adjustment parameters for controlling the shaping process, is difficult to implement in practice, since this requires replacement of tools, each of which must be pre-configured while using a special rather time-consuming technique. The paper reveals that with an increase in the tool rotation frequency and an amplitude of its oscillatory movements, there is an increased removal of material on the periphery of the surface being machined, and with an increase in vibrational movements, on the contrary, the central zone of the part is more intensively activated.

The article presents a new concept of “Management of knowledge about virtual promotion” on the Internet. Usually a real produ ct or service is being divided into four components (product, price, promotion and place) in accordance with the theory of marketing. One of the components is a product promotion. But now this element is becoming a fully virtual tool. It is necessary to consider product promotion as an image or a copy of a real product in a virtual space that lives in parallel on the network. Therefore, the objective of the paper is the presentation of a new object of research based on the experience of more than thirty real projects performed in Ukraine, USA, Europe and Canada. We regard the promotion as a software product, which works according to principles of knowledge management and machine learning. It is proposed that virtual promotion is characterized by four views: customer or user, data, technology and marketing. Thus, the structure of virtual promotion business process was presented. It includes four steps: selection of hypertext sources, knowledge representation and extraction, semantic kernel building and quality criterion evaluation to stop the process. Based on the process structure the research tasks were identified. The central task is semantic kernel forming. Then the software architecture was developed. IT solution contains CRM system as accounting tool and Web site as an image of virtual promotion. CRM plays main role as a commander center. Here we form semantic kernel and then send it via marketing channels such as Web site, telegram or viber accounts. Another part of IT solution is Web service such as Bing API or Google API. They help us to build the kernel. Also the paper demonstrates the list of future tasks that should be solved and the example of real project of proposed approach.

Waste of combined heat and power plants represents a certain danger to the environment, and hence the economic problems. However such waste contains substances that are advisable to use for production of construction and finishing materials. Technogenic products of water treatment from the Yuzhnaya combined heat and power plant (sludges of chemical water treatment – code 8410500) are a calcite mixture containing more than 64 wt. % calcite. The mineralogical composition of inorganic waste has been determined while using X-ray and IR-spectral researches. Mechanical activation of calcite inorganic wastes leads to grinding of calcite and a decrease in the amount of adsorbed water, which affects the increase in the content of silica frame structures, the reactivity of which directly depends on their quantity. Changes in the structure of silicon dioxide during mechanical activation are established according to IR studies. The results of X-ray and IR studies of the Zapolie deposit clay used in ceramic brick production technology make it possible to attribute it to raw materials with high reactivity. An experimental batch of ceramic bricks has been produced at JSC “Obolsky Ceramic Plant” with addition of calcite inorganic waste from combined heat and power plants. An X-ray diffraction analysis of samples of the obtained bricks having standard composition and with addition of waste has been carried out. The influence of calcite inorganic waste content in the feedstock on the process of ceramic brick structure formation has been stu-died in the paper. Addition of chemical water treatment waste containing calcium carbonate up to 15 wt. % to the Zapolye clay mixture helps to reduce a firing temperature and an appearance of the melt. This leads to crystallization processes of solid minerals from the melt and an increase in the amount of glass phase which contributes to improvement of strength properties in ceramic bricks. The possibility of using inorganic waste (sludges of chemical water treatment – code 8410500) of combined heat and power plants as a component of emaciated additives in clay raw materials in the process of ceramic brick production has been established in the paper.

The paper considers spatial organization of energy facilities with an emphasis on modern practice of the Republic of Belarus. The efficiency of enterprise operation in any industry including power industry is largely due to their architectural and planning organization. Knowledge of mechanisms and specific features of the changes taking place here makes it possible to justify a promising strategy for project activities, and therefore, it allows to manage development processes of the industry and thereby avoid many negative consequences. Energy facilities are a typological unit of industrial architecture, their formation has been started due to transition of industrial production to electric energy. Today the typology shows functional approach in architectural shaping, it includes a fairly large variety of constituent units and demonstrates a tendency towards diversification. In Belarus energy facilities in the architectural aspect of their classification are limited mostly to thermal power plants operating on different types of fuel. Currently the diversification is developing in the following areas: construction of hydropower facilities (small plants on reservoirs, medium power plants, low-pressure plants, run-of-the-river hydraulic power stations), alternative energy (wind power stations, photovoltaic power stations and biogas plants) and conventional energy (thermal power plant, mini-combined heat and power plant operating on renewable fuel). The results of Belarusian practice in construction of all types of facilities (hydropower, alternative and conventional energy), peculiarities of the architectural and planning organization of facilities at the current stage, correlation with global trends in the development of industrial architecture have been characterized in the paper. The paper has determined typological features of alternative energy facility architecture, opportunities and directions for implementation of architectural approaches, problems and prospects to develop scientific support for the project process.

The aim of the research is to develop theoretical and methodological foundations of stimulating the production of intensive renewal goods in the Republic of Belarus in the context of increasing the competitiveness of enterprises. To achieve this goal, the concepts of “enterprise competitiveness” and “stimulating the production of intensive renewal goods” have been clarified in the paper. The material for writing the paper comprises the work of domestic and foreign scientists and economists, the data of research reports carried out by the author, as well as industrial development programs and official statements by state managers. General scientific methods (analysis, synthesis, historical and logical unity), a systematic approach have been used in the framework of the study. The paper substantiates the inadmissibility of reducing the essence of an enterprise competitiveness to its competitiveness in individual markets for goods and services. Increasing the competitiveness of an enterprise is considered as a result of its subjective activity, as a reaction to economic incentive measures at various levels (both external and internal ones). This has made it possible to determine competitiveness of the enterprise as its adaptive, innovative, personnel, organizational, managerial, technical and technological, and reproductive characteristics that ensure the acquisition and preservation of comparative advantages determined by the results of interaction with other entities on the basis of a combination of available economic resources. Economiс incentives for production of intensive renewal goods have been consi-dered at various levels. The paper presents a broad interpretation of stimulation the production of intensive renewal goods as crea-ting economic, institutional and organizational-legal conditions that contribute to increasing the competitiveness of the domestic light industry and the fashion industry. As a result of the study, measures that stimulate the development of production of intensive renewal goods have been proposed, their role in increasing the competitiveness of enterprises has been substantiated.

The paper is devoted to study of the modern innovative environment in the Republic of Belarus, its most important characteristics, problem areas. A conceptual apparatus has been given in the paper that determines an innovative environment, institutional conditions that contribute to its formation, priorities for development of research activities have been given and specified in the paper with due account of the requirements for modernization of the economy. The paper presents a definition of the innovation system which is given by distinguished western scientists and researchers who have been seriously engaged in its study. The aim of the research is qualitative, quantitative analysis of the innovation environment of the Republic of Belarus and also a comparative analysis of the innovation environment of the Republic of Belarus, its main components (legal, financial support, institutional specific features of function- ning) against the background of Russia and Kazakhstan. The paper contains SWOT-analysis which is used to find possible directions of innovative development of the economy of the Republic of Belarus on the basis of the existing national economic system and taking into account the peculiarities of the national mentality. Attention has been attracted to the fact that such factor of innovative development as “innovative behavior of employees” which is one of the key factors of competitive advantage in the world's leading companies is very important for evaluation and analysis of the innovation environment. The paper presents an own model of the national innovation system which consists of three subsystems: human capital, technological infrastructure and innovation support subsystem. Process of creating innovative products has been shown in the paper and these products make it possible to understand interrelation of the innovative ideas market and the market of innovative product. It is proposed to use a categorical apparatus of legal acts of the Republic of Belarus to describe and characterize the markets of innovative ideas and innovative products. The analysis has been performed while using legislative acts, resolutions of the Government of the Republic of Belarus, analytical articles, conference materials, electronic resources, official statistics of the National Statistical Committee of the Republic of Belarus.

The paper considers theoretical and methodological foundations for studying network mechanisms of innovative development in the Republic of Belarus and in order to reach the purpose it is necessary to specify the concept of a systematic approach in the context of the study of the indicated mechanisms and develop a methodology for conducting such investigations. Systematic and historical approaches, principles of synergetics have been used as research methods. The paper substantiates the necessity to study the network mechanisms of innovative development in the Republic of Belarus from the point of view of a systematic approach. In this case, the author has refused traditional contrast of stable, essential, regularly repeating connections and relationships in the system to random, chaotic processes, and he has proceeded from the need to consistently apply a law of hierarchical compensation, as well as taking into account such features of the development of the modern economy as the rapid evolution of network technologies, further development of the risk economy, emergence of new challenges for traditional (including old industrial) industries. This has made it possible to define a systematic approach as a se quential and comprehensive examination of an object not as isolated from external influences, but as half-closed, but with an approach to an open system in which the synergetic processes generated by evolution of network technologies, development of the risk economy, and emergence of new challenges for industrial production (including traditional ones). It has been established that a consistent and comprehensive review of the network mechanisms of innovative development in the Republic of Belarus requires not only to determine initial categories and concepts, to show general and special determining factors, genesis and development trends, but also to conduct constant monitoring aimed at identifying dynamics of needs and interests of political-economic and economic entities involved in this process, as well as material and social technologies for implementation of the needs and interests.

Abstract. The paper substantiates the need to study a transport and logistics infrastructure of the regions in the context of its impact on socio-economic indicators for development of the Republic of Belarus. The importance of this study is confirmed by goals and objectives for development of the transport and logistics systems of the Republic of Belarus as outlined in the National Strategy for Sustainable Social and Economic Development of the Republic of Belarus for the period until 2030 and Republican Program for development of logistics systems and transit potential of the Republic of Belarus for the period of 2016-2020. The influence of nine indicators for development of the transport and logistics infrastructure in the regions of the country on six key socio-economic indicators such as gross domestic product, investment in fixed assets, revenues of consolidated budgets, average wage level, number of gainfully employed persons, number of registered unemployed persons has been investigated in the paper. A multiple regression analysis has been used to assess a relationship between dependent and independent variables, that is a step selection method. All the calculations have been carried out while using the IBM SPSS Statistics 20. Indicators of correlation between dependent and independent variables have been calculated and relationships between the variables have been determined in the paper. Validity of the obtained results has been checked with the help of the Student's test. The calculations have made it possible to identify key indicators for a transport and logistics infrastructure in six regions of the country which have the greatest impact on the social and economic development of the Republic of Belarus and can be used to analyze an investment attractiveness of the regions.

The papers considers the following six innovative models of marketing activity: event marketing, brand immersion, geolocation internet-marketing, lead generation internet-marketing, single commodity distribution and trade-service network, van selling. Even marketing is a systematic execution of events used as a platform for presentation of products while attracting attention of potential consumers and exerting emotional impact on them. The model is directed on four targeted objects: consu-mers, partners, market and own personnel. Brand immersion is the involvement of consumers in emotional perception and expe-rience of brand. Geolocation internet-marketing is data penetration (location) of a large circle of consumers via the Internet on a wide geographic site. Lead generation internet-marketing is attraction (generation) of potential consumers (leads) via the Internet. Single commodity distribution and trade-service network is an aggregate of firms or individuals which and who take over or help to transfer ownership of a particular product or service to someone else on their way from a manufacturer to a consumer as well as providing trade and service services. Links of the commodity distribution network are: manufacturers, distributors, wholesalers, dealers, brokers, agents, consignees, retailers, service and repair companies. Van selling is wholesale trade with prompt delivery of goods to consumers and placing orders on the spot (sale from wheels). The essence of each model has been revealed and their values and advantages in commercial activity have been considered in the paper. It has been shown that an introduction of innovations is hindered by various factors: stereotypes of thinking, organizational difficulties, additional material costs, possible lack of direct economic benefits for some participants in the trade. All this makes it difficult to create and implement innovations in trade practice including the use of computer technologies in trade, for example, in the field of public procurement. The paper proposes methods for eliminating these obstacles.

The lifetime of traction battery systems is an essential feature of the economy of battery electric urban bus fleets. This paper presents a model for the analysis and prediction of the lifetime of urban electric bus batteries. The parameterization of the model is based on laboratory measurements. The empirical ageing model is an integral part of a three-stage battery model, which in turn is an important component of the methodology for the overall system design, evaluation and optimisation of battery electric urban bus fleets. In an equidistant closed simulation loop, the electrical and thermal loads of the traction battery are determined, which are then used in the ageing model to calculate the SOH (state of health) of the battery. The closed simulation loop also considers the effects of a constantly changing SOH on the driving dynamics of the vehicles. The model for lifetime analysis and prognosis is presented in the paper, placed in the context of the overall system design and demonstrated by means of a practice-oriented example. The results show that the optimal system design depends, among other things, on whether an ageing simulation was used. Taking battery aging into account, system costs in the example presented can be reduced by up to 17 %.

Hybrid electric powertrains in automotive applications aim to improve emissions and fuel economy with respect to conventional internal combustion engine vehicles. Variety of design scenarios need to be addressed in designing a hybrid electric vehicle to achieve desired design objectives such as fuel consumption and exhaust gas emissions. The work in this paper presents an analysis of the design objectives for an automobile powertrain with respect to different design scenarios, i. e. target drive cycle and degree of hybridization. Toward these ends, four powertrain configuration models (i. e. internal combustion engine, series, parallel and complex hybrid powertrain configurations) of a small vehicle (motorized three wheeler) are developed using Model Advisor software and simulated with varied drive cycles and degrees of hybridization. Firstly, the impact of vehicle power control strategy and operational characteristics of the different powertrain configurations are investigated with respect to exhaust gas emissions and fuel consumption. Secondly, the drive cycles are scaled according to kinetic intensity and the relationship between fuel consumption and drive cycles is assessed. Thirdly, three fuel consumption models are developed so that fuel consumption values for a real-world drive cycle may be predicted in regard to each powertrain configuration. The results show that when compared with a conventional powertrain fuel consumption is lower in hybrid vehicles. This work led to the surprisingly result showing higher CO emission levels with hybrid vehicles. Furthermore, fuel consumption of all four powertrains showed a strong correlation with kinetic intensity values of selected drive cycles. It was found that with varied drive cycles the average fuel advantage for each was: series 23 %, parallel 21 %, and complex hybrids 33 %, compared to an IC engine powertrain. The study reveals that performance of hybrid configurations vary significantly with drive cycle and degree of hybridization. The paper also suggests future areas of study.

This paper is dedicated to Sergei Brukhonenko (1890–1960), a physiologist and inventor of the world’s first heartlung machine. His immense contributions to the development of modern science and technology are investigated. Brukhonenko’s invention is seen as modern biotechnology that has attracted an all-round strong public interest. A philosophical analysis of the differences between the concepts “technique” and “technology” is presented. The paper discusses the sociocultural impact of biotechnology on the society and culture.

The goal of this paper is to analyse the collected data on energy efficiency of electric vehicles from researches done by other authors and also to summarise all the factors affecting it. The majority of data available are obtained through simulations – therefore the emphasis in this paper will be placed on experimentally acquired data. The results of the analysis will be used for the planned e-bus eco-driving project for the purpose of Belgrade’s public transportation system. Currently there are only 5 (ultracapacitor type) e-buses operating in Belgrade city public transport, which makes only 0.2 % of all vehicles in rolling stock (making 16 % together with other electric-powered vehicles – trams and trolleybuses), but there are plans to acquire new 80 electric buses. With the rise of the number of electric vehicles, appropriate training of drivers is gaining more and more importance, and the results of the presented analysis make the basis for such training. This will hopefully increase the range of the buses used and help save the energy spent by public transportation, thus giving a little contribution to global fight for cleaner planet.

The current paper has presented the study results obtained in 2020–2023, in the stationary field trial of the FSBSI “KurskFARC”. The purpose of the study was to identify and evaluate the impact of technologies with different levels of soil tillage minimization on weed infestation, the formation of yield structure elements and pea productivity in the conditions of the CBR. There have been studied four pea cultivation technologies, such as traditional (plowing at 20–22 cm, main application of N15P40K40 + top dressing with N34); differentiated (chiseling by 20–22 cm + disking by 8–10 cm, main application N15P40K40 + top dressing with N34); minimal (discing up to 8 cm, main application N15P40K40 + top dressing with N34); direct sowing (no-tillage, main application N5P14K14 + pre-sowing N10P26K26 + top dressing with N34). There has been established the advantage of traditional technology in reducing weed infestation, and direct sowing in the formation of yield structure elements, indicators of grain quality and pea productivity. The traditional pea cultivation technology reduced the total number of weeds by 1.9–2.0 times and their dry weight by 1.2–1.8 times during the period critical for the growth and development of the crop, and by 2.1–2.5 and 1.3–2.0 times before harvesting. The highest indicators of plant density for harvesting, the mean number of grains per plant and unit area, and protein percentage in grain were identified with direct sowing, which made it possible to obtain the maximum pea productivity (2.31 t/ha) and protein yield with the harvest (460.6 kg/ha). The use of traditional, differentiated, and minimal technologies contributed to a reduction of plant density before harvesting by 5.4–9.3 %, the mean number of grains per 1 m2 by 4.2–22.6 % and per plant by 0.6–18. 6 %, protein percentage in grain by 0.25–0.90 %, which led to a productivity decrease by 4.3–10.8 %, protein yield per hectare by 5.3–12.6 %.

The goal of the research was to develop a technology for introducing Salicornia europaea L.into in vitro culture. Methods of cultivating meristems and callus cultures were studied. To cultivate meristems, the tip of the apical bud were used as an explant. Fragments of stems and leaves were used toobtain callus tissue. To study the influence of various factors on germination, seeds were soaked in sterile tap water and in solutions of gibberellin, cytokinin, auxin and NaCl, and were also subjected to cold stratification (independently and with subsequent placement in Knop’s agarized medium). Salicornia seeds were sterilized with various antiseptics: 70% alcohol, 10% aqueous solution of sodium hypochlorite («Belizna»), amoxicillinand 3% hydrogen peroxide. The ability of the culture to form callus was studied in MS medium. As a result, it was determined that the highest germination of seeds was observed in Knop medium after treating theseeds with a suspension of green algae of the Scenedesmus genus, as well as after preliminary cold stratification, and slightly less after treating the seeds with a solution of NaCl and gibberellic acid. The most effective method of seed sterilization turned out to be treatment with alcohol followed by treatment with sodium hypochlorite. A comparative analysis of seed germination in filter paper in Petri dishes, Knop agar medium, Murashige and Skoog (hormone-free) was carried out. The ability of S. europaea L. to form callusin MS medium with phytohormones was assessed. Conclusion. To improve germination, it is recommended to subject the seeds to cold stratification. To obtain aseptic explants quickly, it is recommended to germinate the seeds in the Knop nutrient medium, having previously sterilized them with alcohol, then with sodiumhypochlorite, followed by washing with distilled water. The most suitable type of microclonal propagationfor S. europaea L. is the production of callus tissue followed by induction of organogenesis or embryogenesis.

Objective. The goal of the study is to optimize a computer model of a Vivaldi antenna with conductive plates on the same side as the resonator.Method. The study is based on electrodynamic modeling methods.Result.The paper presents a computer model of a Vivaldi antenna with conductive plates on one side with a resonator. A comparative analysis of two types of Vivaldi antennas was carried out of the dependence of the beam width and the voltage standing wave ratio on the radius of the current-conducting plate curve in the form of lobes and the values of the opening in two planes θ = 900 (the plane of the antenna's opening) and φ = 00 (the plane perpendicular to the antenna's opening plane) in the frequency range from 3 to 24 GHz. The influence of the shape, size and position of the resonator on the SWR value and the width of the antenna radiation pattern was determined. VSWR values are given for different shapes and sizes of the resonator. The main parameters of the resonator have been identified, which affect the characteristics of the antenna.Conclusion. Electrodynamic modeling allows us to obtain a Vivaldi antenna with the required radiation pattern width with an improved standing wave ratio.

Objective. The noticeable interest in aircraft such as drones for various purposes puts forward certain requirements for their characteristics. Characteristics can be divided into information technology and consumer characteristics from a financial point of view. At the same time, they have their own units of measurement. In this regard, the task of selecting and ranking drones according to some criterion or numerical metric arises. Considering that this problem is quite relevant, this paper considers a certain heuristic approach to sorting a sample of drones by the key of the proposed metric.Method. In the heuristic approach, there is a certain variability in determining the attractiveness of a particular drone in the opinion of the person making the decision to purchase or a specific choice from the existing line of drones available for review based on their characteristics.Result. It is proposed to identify several groups in the existing characteristics, heterogeneous in their properties, both obvious and intuitively created: “good”, “very good”, “less attractive”, “least attractive”. Assuming that several models of drones with the same characteristics are being considered, divided into the specified groups, numerical coefficients are introduced to form a metric by which a given line or selection of drones will be ranked according to the calculated metrics.Conclusion. The proposed heuristic algorithm is based on the transition to the reduced values of numerical characteristics relative to the maximum of each group of characteristics with the calculation of the arithmetic mean of the given values. Depending on the type of specified groups, the coefficients entered into consideration are added or subtracted from the difference between the current characteristic and its average or the difference between the average and the current characteristic. On this basis, metrics are calculated by which the given sample of drone models is ranked.

Objective. The purpose of theoretical research is the need to formulate and describe additional approaches and topical issues and tasks when conducting an expert assessment of group (collective) aspects of the human factor's influence on the safety of technical systems.Method. The paper considers the methodology of assessment based on the use of the Gauss distribution for the statistical description of cases of the influence of the human factor on safety, shows the relationship between individual and group aspects.Result. Examples are given and explanations are given for the application of a quantitative assessment of the influence of the human factor on the safety of technical systems, taking into account the consideration of safety culture, different levels of professionalism of employees, organizational measures taken, the possibilities of the method and its potential tasks are formulated.Conclusion. The use of statistical distributions to describe the impact of the human factor on safety makes it possible to combine and describe the relationship between individual and group aspects of the phenomenon. This allows the expert to carry out quantitative assessments, modeling and make predictions on the level of safety culture in the organization and the effectiveness of production management or technical systems.

Objective. The research presented in the paper is aimed at studying the effectiveness of modern DBMSs.Method. Along with traditional relational solutions, NoSQL-based DBMSs are becoming increasingly popular. This is primarily due to the ability of such systems to store and process huge volumes of data. At the same time, to work effectively with this data, it is necessary to ensure its compression. Compression allows you to reduce the amount of stored data and provide quick access to it.Result. A comparative analysis of data compression in the MySQL and OpenSe DBMS was performed.Conclusion. Data compression in OpenSearch is more efficient than in MySQL when using standard algorithms. OpenSearch is an excellent choice if youneed to conserve storage resources while making optimal use of the processor, otherwise both systems will do the job well.

The relevance of the research topic stems from the necessity methodological tools for evaluating the innovative activity of an organization, taking into account digital transformations that have a direct impact on the level of costs, time and intensity of innovative transformations in an organization under contemporary business conditions. The goal of this study was to systematize and comparatively analyze of methodological approaches to the assessment of innovation and digital transformations in an organization. It also aimed at the development of methodological tools for assessing the innovation activity of an organization, taking into account the relationship between innovation and digitalization. To achieve this goal, general scientific methods of theoretical knowledge were used, including statistical and logical analysis and synthesis, comparison, deduction and generalization, technologies of structural and graphical modeling. The paper substantiates the need to evaluate the innovative activity of an organization, taking into account the level of digital transformation. The systematization of methodological approaches to the assessment of innovative activities of the organization has been carried out, and a conclusion has been made regarding the accessibility and objectivity of the information base and the indicator system proposed by the authors. The interrelation of digital transformations of the organization with its innovative activity is characterized. The systematization of models for evaluating digital transformations of an organization has been carried out, leading to the conclusion that the authors do not pay sufficient attention to the issues of interpenetration of innovations and digital transformations. Based on the results of the study, a methodological toolkit for evaluating the innovation activity of an organization, considering digital transformations, was developed. This toolkit is based on the stages of the organization's innovative activity and the relationship between innovation and digital transformations.

Copyright of Journal of History / Habaršy Tarihi Seriâsy is the property of Al-Farabi Kazakh National University and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

The paper presents a fragment of on-going investigations directed on creation of optimal information environment that ensures an access to the R&D publications from the known scientific journals and other scientific serials which are necessary for qualitative execution of scientific and technological activities on priority areas in highway engineering. A citation analysis has been applied while using data of Journal Citation Reports for selection of world scientific publications which are necessary for execution of investigations on heat and mass transfer in road dressings. Their deformations occur under various climatic conditions due to heat and mass transfer processes, interaction of transport flows and road surface that leads to crack formation in depth and on the surface of road dressings. Structure of constructive layers especially which are created with the help of technogenic wastes (asphalt-, reinforced concrete, concrete, brick scrap and products of their recycling, various wastes of production etc.) exerts an influence on heat and mass transfer. The paper presents results of investigations on heat flows, boundary layers according to viscosity, air velocity, geometric characteristics, permeability, capillary pressures in materials. It has been shown that calculations based on principles of complex number usage have specific features in engineering practice: it is required to observe their accuracy in approaches, calculation reduction due to some accuracy degradation as a consequence of transition from complex numbers to their modules with exclusion of phase shift account and related with propagation of thermal waves. In this respect calculations of heat resistance without phase shifts are considered as rather important if they are in agreement with principles based on the fact that a complexity is characterized by thermal absorptivity of the material in a great number of calculations. The investigations have been supported by Henan Center for Outstanding Overseas Scientists, Grant Number GZS 2018006 (People’s Republic of China, Henan Province).