Search

Introduction. The processes of structure formation of cement compositions and the development of effective technologies of building materials is an urgent task for building material science. The use of large-scale man-made product of pulp and paper enterprises – osprey as a fibrous filler in organic and mineral compositions is the successful decision of the problem. The paper analyzes the ways of using osprey in the building materials’ production. The aim of the research is to study the osprey influence on the processes of structure formation of cement stone by quantitative x-ray phase analysis.Materials and methods. The organic and mineral compositions were obtained on the basis of portland cement and osprey. The authors studied the compositions’ phase of osprey, portland cement and the processes of cement stone structure formation in organ and mineral compositions by quantitative x-ray phase analysis.Results. The authors determined the compositions’ phase of mineral impurities of osprey, cellulose, cement, cement stone, organic and mineral compositions and two compositions containing 25 and 75% by weight.Discussion and conclusions. The osprey application as a filler in the organic and mineral composition causes inhibition of processes of cement hydration. The presence of osprey in the hardening organic and mineral composition leads to a change in the composition and structure of the cement stone in comparison with the phase composition of the cement stone without additives. The result of these changes is a significant increase in the amount of calcite, waterite and a significant decrease in the amount of portland. The authors establish that the effective joint work of the reinforcing component of the osprey with the cement matrix is possible with a limited amount of osprey in organic and mineral compositions.

Objectives. Since the end of the 20th century, liquid crystals have taken a leading position as a working material for the display industry. In particular, this is due to the advances in the control of surface orientation in thin layers of liquid crystals, which is necessary for setting the initial orientation of the layer structure in the absence of an electric field. The operation of most liquid crystal displays is based on electro-optical effects, arising from the changes in the initial orientation of the layers when the electric field is turned on, and the relaxation of the orientation structure under the action of surfaces after the electric field is turned off. In this regard, the high quality of surface orientation directly affects the technical characteristics of liquid crystal displays. The traditional technology of rubbing substrates, currently used in the display industry, has several disadvantages associated with the formation of a static charge on the substrates and surface contamination with microparticles. This review discusses an alternative photoalignment technology for liquid crystals on the surface, using materials sensitive to polarization of electromagnetic irradiation. Also, this review describes various applications of photosensitive azo dyes as photo-oriented materials. Results. The alternative photoalignment technology, which employs materials sensitive to electromagnetic polarization, allows to create the orientation of liquid crystals on the surface without mechanical impact and to control the surface anchoring force of a liquid crystal. This provides the benefits of using the photoalignment technology in the display industry and photonics—where the use of the rubbing technology is extremely difficult. The optical image rewriting mechanism is discussed, using electronic paper with photo-inert and photoaligned surfaces as an example. Further, different ways of using the photoalignment technology in liquid crystal photonics devices that control light beams are described. In particular, we consider switches, controllers and polarization rotators, optical attenuators, switchable diffraction gratings, polarization image analyzers, liquid crystal lenses, and ferroelectric liquid crystal displays with increased operation speed. Conclusions. The liquid crystal photoalignment and photopatterning technology is a promising tool for new display and photonics applications. It can be used for light polarization rotation; voltage controllable diffraction; fast switching of the liquid crystal refractive index; alignment of liquid crystals in super-thin photonic holes, curved and 3D surfaces; and many more applications.

В работе представлены результаты исследования структуры и свойств бумажных обеззоленных фильтров «Синяя лента». Показано, что фильтровальная бумага «Синяя лента» имеет достаточно высокую плотность с относительно малым количеством и размеров пустот (пор) между волокнами. При обработке фильтров в поле коронного разряда наблюдается повышение их механических свойств на 3.5–6%, что вызвано преимущественно усилением межволоконных сил связей. Реализация повышенных электростатических сил связей в структуре листа приводит к увеличению сопротивления внешней растягивающей силе, необходимой для разрыва бумажного фильтра. Наблюдаемые зависимости связаны с ориентацией и упорядочиванием элементов структуры целлюлозно-бумажного материала, с ростом потенциала двойного электрического слоя на поверхности волокон под действием носителей заряда, инжектируемых в объем бумаги из коронного разряда и с образованием гетерозаряда за счет ориентации полярных группировок целлюлозы, сегментов макромолекул во время электретирования. Это подтверждается ростом ζ-потенциала волокон обеззоленных фильтров при обработке в отрицательном коронном разряде – установлено, что значение дзета-потенциала волокон электретированных обеззоленных фильтров на 18% больше, чем для исходных. Достигнутые результаты увеличения физико-механических свойств обеззоленных фильтров позволят повысить эффективность их применения., The article presents the study results of the structure and properties of paper ashless filters "Blue tape". It is shown that the "Blue tape" filter paper has a fairly high density with a relatively small number and size of voids (pores) between the fibers. When processing filters in the corona discharge field, an increase in their mechanical properties by 3.5–6% is observed, this is mainly due to the strengthening of the interfiber bond forces. The implementation of increased electrostatic bonding forces in the sheet structure leads to an increase in the resistance to the external tensile force necessary to break the paper filter. The observed dependences are associated with the orientation and ordering of the pulp and paper material structural elements, with an increase in the potential of the double electric layer on the fibers surface under the charge action carriers injected into the paper volume from the corona discharge and with the formation of a hetero charge due to the orientation of the polar cellulose groups and macromolecule segments during electreting. This is confirmed by the increase in the ζ – potential of the fibers of filters during processing in a negative corona discharge - it was found that the zeta – potential value of electret ashless filters is 18% higher than for the initial ones. The achieved results of increasing the ashless filters physico- mechanical properties will increase the efficiency of their use.

The paper presents the results of experiments to improve the performance of insulating paper as a component of high-voltage paper-impregnated insulation by introducing the modifying additive into the paper mass. Environmentally safe and economically feasible method of obtaining modifying additives of the chitin-glucan complex of Aspergillus niger (A.n.) which is a large-tonnage waste production of citric acid is proposed. The modifying additive was introduced into the paper mass in an amount of 5–10% to the mass of absolutely dry fiber of sulfate insulating cellulose. The paper samples were subjected to accelerated thermal aging at 140°C for 250 hours. The values of the short – term electrical strength of the samples with the modifying additive, both in the initial and in the aged state, exceeded the similar characteristic of the paper sample without additives. for the paper made of 100% cellulose after 250 hours of accelerated thermal aging the maximal mechanical tensile strength decreased by 2.1 times; for paper containing 5% HGC A.n. – by 1.5 times and for the insulating paper, which was introduced into 10% of the modifying additive, the specified parameter during the test has not changed. Comparative evaluation of the sorption activity of the cellulose component was carried out by determining the light transmission coefficient of transformer oil relative to the standard at the process of thermal aging. It was found that the modification of insulating paper by biopolymer also increases its sorption activity in relation to the products of destruction of paper-impregnated insulation components under the catalytic effect of copper., В работе представлены результаты экспериментов по улучшению эксплуатационных характеристик электроизоляционной бумаги, как компонента высоковольтной бумажно-пропитанной изоляции, за счет введения в бумажную массу модифицирующей добавки. Предложен экологически безопасный и экономически целесообразный способ получения модифицирующей добавки из хитин-глюканового комплекса Aspergillus niger (ХГК A.n.) – многотоннажного отхода производства лимонной кислоты. Модифицирующую добавку вводили в бумажную массу в количестве 5–10% к массе абсолютно сухого волокна сульфатной электроизоляционной целлюлозы. Образцы бумаги подвергали ускоренному термическому старению при температуре 140°С в течение 250 ч. Значения кратковременной электрической прочности образцов бумаги с модифицирующей добавкой как в исходном, так и в состаренном состоянии превосходили аналогичную характеристику образца бумаги без добавок. Введение в состав целлюлозной основы модифицирующей добавки способствовало повышению нагревостойкости бумаги, сохраняя показатель механической прочности на высоком уровне в процессе длительного термического старения: у бумаги из 100% целлюлозы после 250 ч ускоренного термического старения предел механической прочности на разрыв снизился в 2.1 раза; у бумаги, содержащей 5% ХГК А.n. – в 1.5 раза, а у бумаги, в состав которой было введено 10% модифицирующей добавки, указанный показатель за время испытаний не изменился. Сравнительная оценка сорбционной активности целлюлозного компонента проводилась путем определения коэффициента светопропускания трансформаторного масла относительно эталона в процессе термического старения. Установлено, что модификация электроизоляционной бумаги биополимером также повышает ее сорбционную активность по отношению к продуктам деструкции компонентов бумажно-пропитанной изоляции в условиях каталитического влияния меди.

Spray drying is currently used to obtain powder products from suspensions. It is considered the most effective type of drying for such media. The complexity of the drying process is associated with thermal destruction of components, which degrades the properties of the product and imposes significant restrictions on temperature condition. The present research features the simulation of transient modes of operation of the solenoids to generate a controlled cavitation effect when applied to a stream of acoustic vibrations using a magnetostrictive generator of ultrasound. The authors propose a new design of spray nozzle for drying suspensions with counter-connected solenoids. Such solenoids can cause deformation of the main suspension supply line. The intensity of the cavitation processes depends on the dynamics of the solenoid actuation. The paper introduces a mathematical modeling of transient modes of operation for ultrasonic frequency generator solenoids that create a controlled cavitation effect when applied to the jet of acoustic oscillations of this frequency. When modeling the process of operation of solenoids, the main criterion for changing the intensity of cavitation is the average rate of change in the volume of the cavity at the stage of its collapse, related to one cycle of oscillations for a spherical cavity. An increase in the static pressure of the liquid led to a shift in the phase of the collapse of the cavity. As a result of the chosen mathematical model, a numerical experiment with modeling in the MathCAD program was carried out. It revealed some graphical dependences of the change in U(t), L(t), and R(t). The obtained data allow one to predict the ballast induction and active load (R, L) for the control of transients in the solenoid of the ultrasonic generator. These dependences make it possible to choose more effective parameters for drying suspensions, which is especially important for heat- sensitive components.

Quality is a time-varying, complex property of a confectionery that shows a measure of acceptability for the customer and rapidly or slowly deteriorates after the manufacture of foodstuffs. The safety of raw materials and finished products during storage is the most important task of global importance, according to WHO, in 2020 year. One of the important problems in the confectionery industry is to ensure long shelf life of confectionery products without reducing their taste properties, as exemplified by jelly marmalade. The task of preserving the freshness of the product is to preserve its consistency, taste, smell, appearance by retaining moisture and preventing damage by microorganisms. Freshness criterion for long shelf life is one of the main factors affecting the sales and competitiveness of sugary confectionery. The aspects of the influence of the properties of structure-forming agents (pectins, agars, modified starches) on the formation of a gelatinous consistency and storage of marmalade are considered. The physical and chemical indicators characterizing the process of moisture transfer in the body of the marmalade during storage are indicated. To assess the migration of moisture during storage, the graphical dependence of aw on the mass fraction of moisture in the marmalade is used - the isotherm of moisture sorption. Analysis of the obtained data of desorption isotherms can serve as a useful tool that shows what proportion of moisture a product is capable of receiving or giving away without losing the properties that characterize the quality of a particular confectionery product. Modern methods are indicated in assessing the quality function of marmalade using a mathematical equation to predict its storage capacity. An integrated approach to ensure the safety of marmalade is considered, which allows predicting its shelf life

The assessment of the suitability of cables of 6–110 kW with XLPE insulation in comparison with cables of the same voltage but possessing paper-oil insulation has been fulfilled on the basis of the method of multi-objective optimization that makes it possible to account not only the quantitative characteristics (of reduced costs), but also qualitative ones. As an indicator of the reliability of the cable line the maximum mean time to failure (the value inversely proportional to the parameter of succession of failures), which is an order more for cable lines with XLPE insulation than for cable lines with paper insulation, is adopted. A comprehensive assessment of the convenience of installation of cable lines revealed that the installation of cable with XLPE insulation features a 1.2–1.6 times easier installation as compared to three-wire (voltage 10 kW) and 1.4 times easier installation as compared to single-core oil-filled cables (voltage of 110 kW). The efficacy of the cables 6–110 kW with XLPE insulation is proved on the basis on the method of multi-objective optimization, that took into account as the costs for the construction and operation of cable lines and the reliability of its operation, ease of its installation and other quality indicators. If the goals taken into account are considered as equally important, the polyethylene-insulated cables for a voltage of 10–110 kW is more efficient as compared to three-wire (voltage 10 kW) and solid (110 kW) cables with paper insulation. Herewith, the cost of the cable with XLPE insulation may exceed the cost of cable with paper insulation up to two times. If the most important aim is to provide the minimum reduced costs for the construction and operation of the cable line, the use of cables with XLPE insulation for voltage of 10 kW is most advisable in individual cases.

The assessment of the suitability of cables of 6–110 kV with XLPE insulation in comparison with cables of the same voltage but possessing paper-oil insulation has been fulfilled on the basis of the criterion of reduced costs. Thus, the comparison was undertaken between cables of various design and material of insulation: three-core paper insulated ones vs. three-core XLPE insulated ones; three-core paper-insulated ones vs. solid wires with XLPE insulation; single-core oil-filled cables of 110 kV with paper insulation vs. solid wires of 110 kV with XLPE insulation. The increase in long-term permissible current loads for cables with XLPE insulation because of the larger permissible temperature of heating in comparison with cables with paper-oil insulation complies with as would increase in the cross-sectional area of cable cores (equal to 0.61 from the original) and therefore reduces the cost of the cable by reducing the cost of manufacture of conductors. The reduced costs of the construction and operation of cable lines with XLPE insulation (accounting the increase in the cost of a cable 1.2 and 2 times as compared with the cost of a cable with three-core insulation), despite the decline in the cost of manufacture of conductors and the reduced annual operating costs (9 % and 17 % respectively of cable lines of voltage of up to 35 kV and 110 kV), occurred to be more than the reduced costs of the construction and operation of cable lines with paper insulation. Currently the cost of one meter of cable with XLPE insulation is less than the cost of cables of AAB, CASB, AASv types of a voltage of 10 kV with aluminium cores, that ensures their undeniable efficacy.

Polychloroprene is widely used as a special-purpose rubber in such industries as automotive, construction, textile industry. Chloroprene rubber takes a significant share in the market of elastomers due to its properties. In recent years, a gradual increase in demand for chloroprene rubbers is expected. This trend is most clearly seen in regions with a developed automotive industry. World leaders in the production of chloroprene rubbers and latex demonstrate their interest in increasing production capacity. In Russia, chloroprene rubber is not produced, the demand is completely met by import. In this paper, the main industrial methods for the production of chloroprene monomer, based on various feedstocks: acetylene and butadiene-1,3, exist in the world practice. Advantages and disadvantages of each of the above methods for producing chloroprene monomer are given. Technical solutions for the improvement of the chloroprene-monomer preparation technology for the steps of chlorination of butadiene-1,3 and dehydrochlorination of 3,4-dichlorobutene-1 in a column apparatus are proposed. An improved process for the preparation of chloroprene rubber from butadiene-1,3 is described. The development of a modern technology for the production of chloroprene rubber based on domestic raw materials will make it possible to obtain a high-quality target product, which will lead to the exclusion of its imports.

Palm oil is comparable to traditional diesel fuel in terms of calorifi c value, stoichiometric ratio, and cetane number. However, its increased kinematic viscosity and pour point make it diffi cult to use in pure form in diesel engines. (Research purpose) To study specifi c features of burning: diesel fuel with various additives of palm oil (biodiesel fuel); pure 100-percent palm oil; biodiesel fuel with various additives of palm oil and hydrogen peroxide, as well as to develop a method to control its combustion process. (Materials and methods) To determine the ignition time lag, the authors chose a method of kinetic modeling of self-ignition of biodiesel fuel in the air. The self-ignition process was simulated using the Chemical Workbench software package. An adiabatic calorimetric bomb model was used to perform calculations. To describe the process of self-ignition, a universal kinetic mechanism was used, which was verifi ed to calculate self-ignition of diesel and biodiesel fuel surrogates, as well as the formation of toxic substances and soot in the combustion processes. (Results and discussion) It is shown that adding palm oil to diesel fuel increases its ignition time lag, especially at low and medium temperatures of 750-950 kelvin. It was determined that with addition of 10 percent palm oil, the ignition time lag of biodiesel fuel is almost the same as that of diesel fuel no more than 5 percent. Increasing the amount of palm oil additive up to 30 percent and more signifi cantly increases the ignition time lag of the fuel. When using only palm oil as a fuel, the ignition time lag in the temperature range of 800-950 kelvin increases in two times. The study determined the optimal amount of hydrogen peroxide to be used for each composition of biodiesel fuel with various additives of palm oil. (Conclusions) It is shown that additives of hydrogen peroxide can infl uence the reactivity of biodiesel fuel and thereby regulate its ignition time lag.

Development of natural biological products – an actual problem of rational and economical use of wood bioresources with which Russia is rich. The coniferous raw material is a source of biologically active extractive compounds possessing immunostimulating, fungicidal, bactericidal activity. Company «Ecovit» makes food and cosmetic production from Pinus Silvestris L., Abies sibirica and Pinus sibirica R. Maur wood greenery. This paper presents results of research of a chemical composition of the by-products formed in coniferous essential oils processing: residue after distillation and florentine water. The extraction of these products is carried out by petroleum ether, diethyl ether, ethyl-acetate consistently and quantitative maintenance of extractive compounds is certain. The qualitative and quantitative analysis of macro- and micro-elements in investigated samples is lead. Chemical structure of extractive compounds is characterized with use of physicochemical meth-ods. In residue after distillation of Abies and Pinus wood greenery carotenoids, natural phenolic com-pounds, carboxylic acids are identified. Ethanol extracts of the fulfilled pine and cedar raw material contain sesqui- and diterpenes, polyprenols, carotenoids, fat acids and phenolic compounds. In Abies ethanol extracts maltol and triterpenoids are identified. The basic components of pine florentine water are monoterpenoids. The received results cause practical application of by-products of coniferous raw material processing for obtaining of biologically active additives, preparations for agriculture, pharmacology, perfumer-cosmetic production., Разработка природных биопрепаратов – актуальная задача рационального и экономного использования лесных биоресурсов, которыми богата Россия. Хвойное сырье является источником биологически активных экстрактивных веществ, обладающих иммуностимулирующей, фунгицидной, бактерицидной активностью. Компания «Эковит» производит пищевую и косметическую продукцию из древесной зелени сосны Pinus Silvestris L., пихты Abies sibirica, кедра Pinus sibirica R. Maur. В данной статье представлены результаты исследования химического состава побочных продуктов, образующихся при производстве хвойных эфирных масел: кубового остатка от гидродистилляции древесной зелени и флорентинной воды. Определен количественный состав экстрактивных веществ, извлекаемых из вышеперечисленных продуктов последовательно петролейным эфиром, диэтиловым эфиром, этилацетатом. В исследованных образцах проведен анализ содержания микро- и макроэлементов. Охарактеризован групповой химический состав экстрактивных веществ с использованием физико-химических методов анализа. В кубовых остатках пихты и сосны идентифицированы каротиноиды, природные фенольные соединения, карбоновые кислоты. Спиртовые экстракты отработанного сырья сосны и кедра содержат сескви- и дитерепеноиды, полипренолы, каротиноиды, жирные кислоты и фенольные компоненты. В спиртовом экстракте пихты идентифицированы мальтол и тритерпеноиды. Основными компонентами флорентинной воды сосны являются монотерпеноиды. Полученные результаты обуславливают практическое применение отходов переработки хвойного сырья для получения биологически активных добавок, препаратов для сельского хозяйства, фармакологии, парфюмерно-косметической продукции.

The article is devoted to the analysis of modern priorities in the sphere of food industry main branches development. The author identified the most promising of them, in particular, modification of socially significant food products (fats) by means of their combination with traditional and non-traditional plant raw materials having full fat oil and low-oil content as a source of physiologically functional nutrients. Chemical composition of raw materials has been studied to reveal the biological value and food safety. The efficiency of using wheat germ flour as an ingredient of vegetable fatty composite mixtures in bread production is established. The author suggested using composites that consist of germinated wheat product, animal fat, creamy melted butter, palm, soybean and sunflower oils which have balanced fatty acids content. The author justified the relevance of heat treatment of composite mixtures having wheat germ flour content up to 30.0% of the mixture mass at 40–50 °C, more than 30% – up to 70°C during 10–15 min. That will help increase its microbiological purity, reduce the enzymatic action of germ lipase, protease and lipoxygenase, extend the mixtures shelf life up to 45 days. Optimum proportion of wheat germ flour should not exceed 70.0% of the raw material mixtures weight. It was demonstrated that 30,0 to 50,0% of solid fats can be replaced with vegetable oils. There was a positive effect of the developed composites in the amount of up to 5.0% to the quantity of flour according to the recipe on the quality of bread produced from the 1st grade wheat flour.

Extracellular polymeric substances (EPS) – biopolymers produced by the microorganisms – are effective flocculants of wastewater pollution and lack the shortcomings of traditional coagulants and flocculants, which can pose direct threat to health and human life, as well as to the sustainable existence of aquatic and terrestrial ecosystems. EPS do not form secondary contamination of their degradation intermediates, are biodegradable and eco-friendly. Industrial production of bacterial EPS is associated with high cost of growing specific microbial biomass and the functioning of technologies for the synthesis of microbial products. At the same time, there is an underused resource of excess activated sludge, which can be used as cheap substrate for producing bioflocculants and a possible measure to reduce costs. The conducted researches have shown the prospects of extracting EPS from excess activated sludge for their subsequent use as wastewater treatment bioflocculants. EPS extraction has been conducted using three methods: combination of centrifugation processes, extraction using the aqueous solution of disodium ethylenediaminetetraacetic acid, and precipitation with isopropyl alcohol (the EDTA method); combination of centrifugation, extraction with (NH2)2CO, precipitation and ethanol reprecipitation (the (NH2)2CO method); combination of activated sludge ultrasonic treatment, centrifugation, extraction with glacial acetic acid, and precipitation with acetone (the CH3COOH method). The research has shown that the extraction method affects not only the efficiency of EPS extraction, but also the possibility of EPS application for the purification of certain types of sewage. The (NH2)2CO method has shown the best extraction efficiency, but at the same time EPSs produced have not be able to perform fish processing wastewater treatment. The EDTA and CH3COOH methods are more preferable for producing efficient bioflocculants for fish processing wastewater treatment. The use of EPS obtained by the EDTA method has resulted in the significant reduction of total suspended solids and optical density; EPS produced by the CH3COOH method have reduced the content of dissolved solids and the optical density. According to the conducted research EPS produced from surplus sludge with the EDTA and CH3COOH methods have good flocculation and are harmless for humans and the environment, and thus may be a potential substitute for traditional synthetic flocculants and could be used in the treatment of fish processing plants wastewaters.

Kinetics of catalytic esterification of glycerol with butanoic acid on model systems was studied. Reaction orders for the reactants (butanoic acid and glycerol) were determined. They are close to 1.It was shown that the reaction order with respect to the catalyst - orthophosphoric acid - in regions where its concentration is above 0.1 mol/l is equal to zero. The estimated value of activation energy is 51.9± 8.0 kJ/mol. The results of the experiment can be used to create an industrial technological process for the synthesis of glycerol tributyrate. This compound can be used as an alternative non-phthalate plasticizer for articles made of PVC. The obtained kinetic model was validated on glycerol-containing waste of the biodiesel synthesis from renewable raw materials. The recycling of the by-product in the biofuel production with obtaining plasticizing compositions for the polymer industry can be developed on the basis of the studies.

Objective. The purpose of the article is to analyse the existing methodology used to assess the efficiency of automated information security systems by studying open literature sources, international and industry standards of the Russian Federation on information security of automated systems, guidelines and orders of the Federal Service for Technical and Expert Control of Russia, as well as departmental orders, instructions and regulations on information security at informatization facilities of internal affairs bodies. The analysis results in identifying the advantages and disadvantages of the specified methodology, as well as the possibilities of its use when conducting a quantitative assessment of the efficiency of access control subsystems of information security systems at the informatization facilities of internal affairs bodies. Methods. To achieve this goal, the method for system analysis of approaches used to assess the efficiency of information security tools and systems has been applied. Results. The paper presents results of analysing the main approaches used to assess the efficiency of tools and systems for information security of automated systems. The paper determines the relationship between the efficiency indicator of access control subsystems of information security systems and the main disadvantage of their use in protected automated systems of internal affairs bodies. The paper substantiates main directions of improving the existing methodology, proposes methods and indicators for quantifying the efficiency of access control subsystems (including those modified on the basis of using new information and communication technologies) of information security systems in protected automated systems of internal affairs bodies. Conclusion. The results obtained can be used to quantify the security level of existing automated systems and those being developed at informatization facilities of internal affairs bodies.

Objective. One of the most effective ways to assess thermal protection of construction facilities of various applications is thermal control. Methods. According to the national standard “Method for thermal imaging quality control of thermal insulation of enclosing structures” in force on the Russian Federation territory, the results of thermal imaging monitoring of capital and completed construction facilities are divided into qualitative and quantitative depending on set goals and objectives. Qualitative assessment involves computer processing and visual interpretation of thermograms using specialized software. Quantitative analysis of thermograms involves determining and numerically comparing parameters of reference areas and characteristics of defects detected in an object being under thermal control. Results. The paper describes particular characteristics and results of qualitative and quantitative analysis of thermograms (thermal images) obtained via thermography of fragments of external enclosing structures of a completed construction facility—an apartment building. The paper analyses existing methods of a quantitative assessment of thermograms described in regulatory documents and methodological recommendations, and presents specific examples of their application. Conclusion. Thermal imaging diagnostics makes it possible to qualitatively and quantitatively assess the level of thermal protection of the outer shell of an object under control by “decoding” thermograms and comparing calculated parameters with standard indicators.

The paper describes a technique for assessing the thermally stressed state of a concrete massif of a foundation slab made of a self-compacting concrete mixture. The proposed method consists in a preliminary calculation of temperature fields in hardening concrete. The objects of research have been self-compacting concrete mix and structural concrete in the structure mass. The choice of materials for the preparation of a concrete mixture is given and substantiated. The composition of self-compacting concrete has been used to assess the thermally stressed state. A binder with a reduced exotherm has been used in order to reduce the self-heating of concrete. Studies have been carried out to assess the specific heat release of the recommended cement depending on the initial water-cement ratio. The effect of a chemical additive on the rate and magnitude of the specific heat release of cement has been studied. The paper presents the main theoretical provisions and an algorithm for calculating the thermal stress state of a concrete massif. The finite difference method has been used to calculate the expected temperatures and their distribution in the structure mass, and the temperature stresses in the sections of the concrete mass have been calculated to assess the thermally stressed state. The performed calculations of the temperature fields have made it possible to estimate the maximum possible temperatures and temperature differences over the sections of the concrete massif depending on the initial temperature of the concrete mixture and the average daily temperature of the outside air. Analysis of the temperature distribution has revealed the most dangerous sections of the concrete mass. An assessment of the thermal stress state of the concrete mass has been made on the basis of the results pertaining to calculation of temperature fields. The calculation of temperature stresses in the most dangerous sections of the concrete massif has been performed. It is shown that the calculated value of the temperature stress can serve as a characteristic of the thermally stressed state of the concrete mass. The formation of temperature cracks in a concrete mass is possible when the calculated value of the temperature stress exceeds the actual tensile strength of concrete. Comparison of the calculated and actual values of temperatures in the sections of the foundation slab has made it possible to conclude that the calculations of the temperature fields and, as a consequence, possible temperature deformations are correct.

A schematic and structural solution of regenerative-utilization heat use in centralized heat supply systems was previously proposed in order to increase the efficiency of operation of heating networks located in non-passable channels. The impossibility of creating a full-scale experimental setup covering the required range of factors and the area of their change, the complexity of a passive experiment on existing heating mains led to the need to develop a virtual model based on the ANSYS sofware package. A six-factor experiment has been carried out on this virtual model. Regression equations have been obtained to determine the pressure required to provide air purging of the channel, as well as heat exchange with pipelines of direct and return network water located in the channel, and heat exchange with soil around the channel. In addition, a regression relationship has been derived to find the integral heat flux from the listed washed surfaces to the air flow. The transition from dimensionless to natural factors has been made in the paper. The most significant factors are identified with the help of Pareto cards. The obtained dependencies have been verified in Part 1 of the paper. The adequacy of the obtained regression equations has been determined using standard statistical estimation methods based on the calculated values of the Fisher’s, Student’s and other criteria. The response surfaces are presented and analyzed using two dimensional sections for a number of factor values at fixed values of one and a change in two most characteristic, physically significant for a given response function. They have been validated on the basis of the analysis of regression dependencies. The obtained regression equations cover almost the entire range of possible diameters of heating mains, which makes it possible to use them in the development of energy-saving projects.

In recent years, intensive research on urban transport has been observed. The search is about finding such solutions that will enable, among others: increasing the importance of public transport, matching transport for the needs of people with reduced mobility, increasing capacity, reducing emissions, energy efficiency (technical and organizational dimension through the organization of transport on demand), increasing the vulnerability to recycling and remanufacturing. The paper presents the main concept and technical solutions of the innovative transport system – HMASSUT Prometheus (Hybrid Modular Autonomous System for Sustainable Urban Transport), which combines the concepts of personal rapid transport and an electric vehicle at the L4 autonomy level (according to the Society of Automotive Engineers classification). An assessment of the effectiveness of an innovative transport system using indicators used in road engineering is given in the paper. The concept of simulation and optimization of the transport network is presented together with the theory of cellular automata.

The mixed problem for the telegraph equation well-known in electrical engineering and electronics, provided that the line is free from distortions, is reduced to a similar problem for one-dimensional inhomogeneous wave equation. An effective way to solve this problem is based on the use of special functions – polylogarithms, which are complex power series with power coefficients, converging in the unit circle. The exact solution of the problem is expressed in integral form in terms of the imaginary part of the first-order polylogarithm on the unit circle, and the approximate one – in the form of a finite sum in terms of the real part of the dilogarithm and the imaginary part of the third-order polylogarithm. All the indicated parts of the polylogarithms are periodic functions that have polynomial expressions of the corresponding degrees on an interval of length in the period, which makes it possible to obtain a solution to the problem in elementary functions. In the paper, we study a mixed problem for the telegrapher’s equation which is well-known in applications. This problem of linear substitution of the desired function witha time-exponential coefficient is reduced to a similar problem for the Klein – Gordon equation. The solution of the latter can be found by dividing the variables in the form of a series of trigonometric functions of a line point with time-dependent coefficients. Such a solution is of little use for practical application, since it requires the calculation of a large number of coefficients-integrals and it is difficult to estimate the error of calculations. In the present paper, we propose another way to solve this problem, based on the use of special He-functions, which are complex power series of a certain type that converge in the unit circle. The exact solution of the problem is presented in integral form in terms of second-order He-functions on the unit circle. The approximate solution is expressed in the final form in terms of third-order He-functions. The paper also proposes a simple and effective estimate of the error of the approximate solution of the problem. It is linear in relation to the line splitting step with a time-exponential coefficient. An example of solving the problem for the Klein – Gordon equation in the way that has been developed is given, and the graphs of exact and approximate solutions are constructed.

The paper proposes an approach based on the use of mathematical methods for modeling the behavior of the designed web application and user behavior. This approach allows an evaluation of the usability of this application. The paper discusses the models of user interfaces (UI), which are used to assess the convenience of site navigation. The possibility of using two classes of UI models is shown – structural-logical (ontological) and probabilistic. Models of the first class are used to assess the degree of comprehensibility of the proposed UI navigation on the search web resource in the accepted terms. For this, mathematically defined measures of similarity between the elements of the UI and their relationships and the elements of a hypothetical (but plausible) model of the user’s perception of the search area in a given subject area are used. In particular, the paper substantiates the possibility of using Jaccard and Levenshtein lexicographic distance metrics as such measures of similarity. Probabilistic models are based on Markov chains. With the help of these models, in the presence of reliable statistical data collected during the trial operation of a web application or its prototype, it is proposed to estimate the average number of user steps required to solve a specific problem of finding information about a subject area object. The paper provides some recommendations on the use of similarity measures to improve the usability of the UI of web applications. In addition, data on the technique for estimating the probabilities of transitions of Markov chains and semantic connections are presented. To clarify the features of the UI analysis models proposed in the article, the website of the RTU MIREA Admission Committee (https://priem.mirea.ru) is provided with a fairly simple organization that provides a search for information about admission and training at the University. The application of the approach described in the paper, along with traditional methods of testing the usability of UI, will increase the overall level of usability of applications, and thereby reduce the cost of identifying and correcting related errors.

The paper considers one of the numerical methods to solve problems of scattering electromagnetic waves on the systems formed by parallel-oriented cylindrical elements – two-dimensional photonic crystals. The method is based on the classical partition approach used for solving the wave equation. Тhe method principle is to represent the field as the sum of the primary field and the unknown secondary field scattered on the medium elements. The mathematical expression for the latter is written as the infinite series according to elementary wave functions with unknown coefficients. In particular, the N elements-scattered field is found as the sum of N diffraction series in which one of the series is composed of the wave functions of one body and the wave functions in the remaining series are expressed in terms of the eigenfunctions of the first body using addition theorems. Further, to meet the boundary conditions, on the surface of each element, we obtain systems of linear algebraic equations with the infinite number of unknowns – the required expansion coefficients, which are solved by standard methods. A feature of the method is the use of analytical expressions to describe diffraction on a single element of the system. In contrast to most numerical methods, this approach allows one to obtain information on the amplitude-phase or spectral characteristics of the field only at the local points of the structure. The high efficiency of this method stems from the fact that there is no need to determine the field parameters in the entire area of space occupied by the multi-element system under consideration. The paper compares the calculated results of the transmission spectra of two-dimensional photonic crystals using the considered method with the experimental data and numerical results, obtained by other approaches, and demonstrates their good agreement.

Introduction. This paper presents the results of a study on the methods for calculating the capacity of level crossings. The purpose of writing this research paper is determine the best methodology for calculating the intervals in the main flows for the prevailing road conditions in the Russian Federation, that a new methodology to calculate capacity adapted to domestic road conditions would be developed in the future.Materials and methods. In recent decades of market relations in the Russian Federation, one can note a rapid increase in motorization in human settlements. The number in 550 vehicles per 1000 people in domestic entities is expected to have been increasde by 2025, which is significantly higher than the current level in European part of the Russian Federation. It is important to note that when the number of vehiclec is increasing, which level is about 80%, it is essential to increase road crossings capacity. Results. At the moment the methodology for calculating capacity and queue length is the same. It should be noted that the current models are not properly described in the domestic studies, but the calculations were made using models developed in the 1960s and 1970s.

Implementation of the task of creating a digital platform for a full-featured system of information and analytical support for public administration at the federal, regional and municipal levels, requires a lot of resources and serious expertise.In this regard, the subject of the study was the experience and trends in the construction and operation of digital platforms for state and public administration. The aim of the paper was to summarize the international practice of creating, operating and developing digital public administration platforms. As part of the study, the authors carry out a systematic, content and comparative analysis of various sources: regulatory documents, scientific papers, analytical materials of a number of international organizations, etc.The article presents the results of a study of world experience in the application of various tools to support e-government and support digital governance platforms. The authors describe global trends in the use of information and communication technologies to support public administration. The paper presents a list of general principles for the operation of digital platforms, gives the results of the analysis on the compliance with these principles of the state digital platform of the European Union, highlights its distinctive properties.The article forms proposals and development directions, based on the results and available studies on the development and promotion of digital management platforms, that can help accelerate the spread of digital transformation of public administration in the Russian Federation. The results of the study can be applied to identify the potential of the existing platform, its strengths and weaknesses, including in the context of the possibilities of developing the process of digital transformation of governance, as well as effectively moving towards the formation of the digital platform of public administration in the Russian Federation.

The effectiveness of research teams and scientists is largely estimated by their publication activity. One indicator of the quality of scientific work is the absence of plagiarism. The purpose of this paper was to consider the problems that arise with the formal-mechanistic approach to the detection of plagiarism in scientific papers. The questions of the correlation of meaning and plagiarism; quoting your own work; quoting and inaccurate quoting; the use of generally accepted expressions, laws, definitions; the need to refine anti-plagiarism systems are considered. It is shown that due to the fact that anti-plagiarism systems do not analyze the meaning of the text, “overdiagnosis” occurs. As a result of an uncritical approach to the conclusions of such systems, the writing of scientific papers becomes more complicated. The necessity of developing more accurate criteria for determining what is plagiarized in scientific papers is noted. Some suggestions were made to reduce the shortcomings of the formal approach.

In the operation schemes of optical electronic devices (OED), such as digital autocollimators, direction finders, Shack-Hartmann sensors, as well as astro-orientation systems, projection measuring systems, geometric calibration schemes for OED, the photo-detector acts not only as a receiving device, but also as a measuring device. The tasks facing the OED photo-detectors. The solution to the problem is the use of several photo-detectors installed on one electronic board. Since OED photo-detectors act, inter alia, as measuring devices, it is necessary to perform their geometric calibration. Geometric calibration involves the measurement of interior orientation parameters used in the processing of OED images. Geometric calibration makes it possible to eliminate errors in mutual exposure of photo-detectors on one electronic board installed in the focal plane, as well as distortions introduced by the OED lens, primarily by distortion. The correctness of the interior orientation parameter determination is influenced by the relative position of the collimator, with the help of which the geometric calibration is performed, and the calibrated OED itself, i. e. the external orientation elements. The task is to separate the interior orientation parameters and the elements of external orientation. This is achieved using the method of mathematical processing of measured data in the forward and inverted positions of the collimator. This method of geometric calibration allows to use it for geometric calibration of OED with a large number of photo-detectors. The paper presents the results of the geometric calibration of the interior orientation parameters when the collimator projects a test object onto three photo-detectors of the OED layout. The factors influencing on the accuracy of the geometric calibration of the interior orientation elements for OED are determined in the paper. The developed method for geometric calibration of the interior orientation parameters for multi-matrix OED provides high measurement accuracy – not more than 0.1''–0.2''.

Introduction. The main work objective is systematization and analysis of structural defects of vacuum ion-plasma coatings; on this basis, their classification principles are developed and given in the paper. Another important part of the work is the experimental study on one of the specific defects of coatings, which the authors propose to call “defect of substructural origin”. Materials and Methods. PVD coatings of various nitride and metal systems 1.5-9.0 μm thick were used as an object of the research. Coatings were applied in vacuum installations using arc and magnetron evaporators. The research results were obtained by high resolution electron microscopy, energy dispersive analysis and indentation. Results. Various types of defects in ion-vacuum coatings are presented as the research results. They include discontinuities, deformation of crystallites, and structural inhomogeneity. The principles of their systematization are validated. It is proposed to classify defects into droplet, substructural, and growth defects (depending on the causes of their nucleation), as well as regular and stochastic ones (depending on their distribution in the coating volume). The study of “substructural defects”, classified by the authors as stochastic, is given special consideration. These micrometric defects are shaped like a cylinder with a conical “head”. Their main axle is oriented perpendicular to the surface of the coating. They can be “extruded” (tore away) by the coating. The paper validates the dislocation mechanism of their nucleation and the helicoid growth principle. Conclusions. The inference is summarized that the proposed systematization of defects in ion-plasma coatings has the character of an intermediate result of research in this scientific area. At this, the “substructural defects” do not have a fatal effect on the structure and properties of the coating due to a small size.

Introduction. Various algorithms for solving fuzzy vehicle routing problems are considered. The work objective was to study modern methods for the optimal solution to fuzzy, random and rough vehicle routing problems. Materials and Methods. The paper reviews fuzzy vehicle routing problems, existing methods and approaches to their solution. The most effective features of some approaches to solving fuzzy vehicle routing problems considering their specificity, are highlighted. Results. The Fuzzy Vehicle Routing Problem (FVRP) occurs whenever the routing data is vague, unclear, or ambiguous. In many cases, these fuzzy elements can better reflect reality. However, it is very difficult to use Vehicle Routing Problem (VRP) solving algorithms to solve FVRP since several fundamental properties of deterministic problems are no longer fulfilled in FVRP. Therefore, it is required to introduce new models and algorithms of fuzzy programming to solve such problems. Thus, the use of methods of the theory of fuzzy sets will provide successful simulation of the problems containing elements of uncertainty and subjectivity. Discussion and conclusions. As a result of reviewing various methods and approaches to solving vehicle routing problems, it is concluded that the development and study of new solutions come into sharp focus of researchers nowadays, but the degree of elaboration of various options varies. Methods for the optimal solution of FVRP are limited, in general, to some single fuzzy variable. There is a very limited number of papers that consider a large number of fuzzy variables.

The aim of the article is to analyze the problem of women's radicalization. Based on a review of the literature, it seems possible to say that this problem is often ignored, terrorism is considered as the men’s activity, it is mistakenly believed that women are hardly capable of aggressive behavior, in case of involvement in terrorist activities, they are in a minor capacity. For terrorist organizations, it is a strategic step to use women because women are assigned the tasks where men can attract attention and be caught. In the activities of a terrorist organization, women perform a number of different roles: informants, specialists in developing propaganda strategies, recruiters, managers, qualified specialists, interpreters, objects of sexual bait, fighters. Information distributed by women is perceived differently from that distributed by men, it takes on a different meaning. The paper discusses the specific features of the reasons why men and women become radicalized, noting that the mechanisms of radicalization themselves hardly differ in the case of men and women. The paper is focused on the applicability and potential of theoretical schemes to explain the radicalization of women. Special attention is paid to the theory of uncertainty-identity, and empirical data obtained within the framework of this theory are discussed.

The paper deals with a problem of the obfuscated JavaScript code detection and classification based on Abstract Syntax Trees (AST) coloring. Colors of the AST vertexes and edges are assigned with regard to the types of the AST vertexes specified by the program lexical and syntax structure and the programming language standard. Research involved a few stages. First of the all, a non-obfuscated JavaScript programs dataset was collected by the public repositories evaluation. Secondly, obfuscated samples were created using eight open-source obfuscators. Classifier models were built using an algorithm of gradient boosting on the decision trees (GBDT). We built two types of the classifiers. The first one is the model that classifies the program according to the type of the obfuscator used, i.e. based on what obfuscator created the sample. The second one tries to detect samples obfuscated by the obfuscator whose samples are not observed during training. The quality of the obtained models is on par with the known published results. The feature engineering method proposed in the paper does not require a preliminary analysis of the obfuscators and obfuscating transformations. In the final part of the paper we analyze a quality of models estimated, discussing the certain statistical properties of the obfuscated and non-obfuscated samples obtained and corresponding colored ASTs. Analysis of generated samples of obfuscated programs has shown that the method proposed in the paper has some limitations. In particular, it is difficult to recognize minifiers or other obfuscating programs, which change the lexical structure to a greater extent and the syntax to a lesser extent. To improve the quality of detection of this kind of obscuring transformations, one can built combined classifiers using both the method based on the AST coloring and the additional information about lexemes and punctuation, for example, entropy of identifiers and strings, proportion of characters in upper and lower case, usage frequency of certain characters etc.

Purpose of the research. The aim of the study is to develop recommendations on the selection of parameters for modifying the ant colony method when searching for a rational solution to the task of appointing employees to work, subject to setting the time to complete the work using fuzzy sets and taking into account the interaction time between employees assigned to one task. The algorithm is proposed for modifying the ant colony method. Various stopping algorithms of the modified ant colony method are considered.Materials and research methods. The use of the ant colony method developed for finding the traveling salesman’s path for the assignment problem requires the creation of a “decision graph” and some modifications of the algorithm associated with entering weights (pheromone) on the graph. The paper proposes to create a graph of solutions by creating a set of vertices that determine the appointment of an employee for tasks for each employee and calculating the path in the graph that determines the solution to the assignment problem. To stop the algorithm of the ant colony method, two different algorithms are considered: the stop when performing a certain number of iterations and the stop when finding a solution that satisfies the constraints. To evaluate the effectiveness of the algorithm, the following criteria were considered: the estimate of the mathematical expectation of the number of iterations of the algorithm, the estimate of the mathematical expectation of the criterion value, the estimate of the mathematical expectation of the number of considered solutions, etc. For all estimates of mathematical expectation, a confidence interval is also calculated. According to the estimates, the paper gives recommendations on the selection of parameters of the ant colony method: the number of agents, evaporation rate, parameters of the elite and ranked method of ant colonies, etc. Both the speed and the ability to find rational solutions for different values of constraints are evaluated.Results. The work considered the task of appointing 35 employees for 15 tasks. As a result, the following recommendations were identified on the choice of parameters to the modified method of ant colonies. The more agents, the better solution found, but the number of the considered solutions increases, which leads to an increase in search time. For the evaporation coefficient, it is recommended to choose a value in the range (0.8; 0.95). It is recommended to use a ranked algorithm with a parameter 4 times less than the number of agents in the group. The problem of “cycling” of the ant colony method, caused by the passage of agents along the same routes, is determined.Conclusion. The developed recommendations make it possible to use the ant colony method to solve the problem of assigning employees to tasks. The proposed recommendations on the parameters provide high speed and accuracy of finding a rational solution to the problem. The problem of “cycling” of the ant colony method is described.

In this article, the authors consider the possibility of using a hybrid energy storage system to even out the load profile of the enterprise. Solving the problem of rational use of energy storage taking into account the initial variable load schedule will significantly reduce not only the cost of electricity consumption by the enterprise, but also the costs of its production. Detailed characteristics of batteries with various types of electrolytes and supercapacitors are given. A model of the active scheme of a hybrid electric energy storage system consisting of a lithium-ion battery and a supercapacitor unit with the corresponding characteristics is presented. The model was carried out by using the SimPowerSystems software in MatLab. During the simulation, the temperature and the aging effects and of the batteries were not taken into account. The selfdischarge parameter of the battery was also not presented. As a result of the simulation, discharge characteristics of supercapacitors and batteries were obtained based upon which the expediency of their combined use for leveling load profiles of various types was substantiated. The paper presents the results of the simulation of operating modes of a hybrid energy storage device, combining the advantages of two types of energy storage devices, as well as a diagram of delivered power to the network, corresponding to the specified parameters. The paper provides a mathematical description of the increasing power by hybrid storage system resulting from the combined use of supercapacitors and batteries. The paper presents the dependence of the power increase ratio on the frequency and the pulse current duty ratio, which proves that the maximum possible output power of the hybrid storage system can be several times greater than the power of a single battery having the same parameters.

Introduction. The process of shifting gears under load is one of the most complex types of dynamic process in the transmissions of transport, road and construction vehicles. Currently, the existing calculation methods do not fully reflect the features of the engine and automated gearbox interaction by switching stages under load using more than two friction clutches at the same time. The paper discusses the method of calculating the dynamic characteristics of the gearbox with the simultaneous use of both two and four friction clutches by shifting gears under load with forward and reverse switching. The authors present the results of the dynamic characteristics of the theoretical study of the automated gearbox with frictional stages’ switching under load and without breaking the power flow.Materials and methods. The main method was based on a system approach to the dynamic processes study and on the modeling of the gearbox operation together with the internal combustion engine. The authors took into account the regulatory, speed and load engine characteristics, resistive torque variation, rate of pressure rise in clutches by shifting to higher and lower gears. The paper performed theoretical modeling of processes using the MATLab package and the Simulink application. Using the main blocks of this application, the authors created models of physical components: an internal combustion engine, friction clutches, gear reducers, elastic shafts, damping devices and tractor power transmission control systems.Results. As a result, the authors obtained calculated data of the dynamic processes, variations in speed and rotational torque on the gearbox shafts; the load on the engine by shifting gears at different values of the start and finish time in switching on and off the gearbox friction controls. The paper presented the relevant graphs of the processes.Discussion and conclusions. The developed method of calculating the dynamic characteristics of the gearbox allows simulating workflows by shifting to higher and lower gears. This method takes into account both the parameters of the gearbox design and of the control actions: the rate of switching on the friction clutches; the time intervals of overlapping the “on and off” clutches. Therefore, in relation to the considered gearbox, the authors determine the values of the optimal time control commands of the friction by shifting.Financial transparency: the authors have no financial interest in the presented materials or methods. There is no conflict of interest.

Introduction. The paper devotes to the features of hydration and hardening of polymineral composite binders. The authors carry out the complex research of the phase composition, hydration and structure formation processes of hardened composite binders with active mineral additives by X-ray phase analysis, differential scanning calorimetry and electron microscopy. The study using a Tescan MIRA 3 scanning electron microscope reveals differences in the microstructure of hardened binders and the authors confirm the results by microprobe studies. The authors study the hydration of the composite binder prepared on the basis of Portland cement and mineral components. Moreover, the paper demonstrates the dynamics of the system’s heat dissipation from the moment of mixing with water and hardening up to 24 hours and up to 72 hours by the expressed bond of dQ / dt = f (t) using a differential calorimeter.Methods and materials. The authors carried out experimental studies at Belgorod State Technological University named after V.G. Shukhov, at the Department of Building Materials, Products and Structures, at the High Technology Center and “BelGTASM-Certificate” Test Center. Therefore, the authors used the existing basic research methods, including modern physicochemical methods of analysis: X-ray phase, scanning electron microscopy, etc. The paper determined the main characteristics of raw materials, composite binders and foam concrete using standard methods and regulatory requirements.Results. The authors obtained the results that testified the peculiarities of hydration and hardening processes of polymineral composite binders on the basis of Portland cement and mineral additives: opoka marl and fly ash.Conclusion. The research establishes the hydration and hardening processes of polymineral composite binders. As a result, the authors demonstrate that the opoka marl introduced into the cement leads to the increased hydration in the induction and accelerated periods and also increases the hydration completeness of the main clinker minerals due to the manifestation of the pozzolanic reaction and the active binding of blocking Portlandite, as well as to the higher concentration of accumulated neoplasms, second generation calcium hydrosilicates.Financial transparency: the authors have no financial interest in the presented materials or methods. There is no conflict of interest.

Over the past few years the popularity of blockchain technology has grown significantly. It is able to make change as the economic environment, as also identifying new approaches to business management. The paper is devoted to innovative aspects that appear and have a tendency to develop in the field of accounting and audit due to the blockchain technologies development. This technology can affect entire industries, and especially the financial sector. The decision to use blockchain in combination with appropriate data analytics can help in accounting processes, as well as in conducting daily transactions involved in the audit. The transition to a financial system with a significant element of the blockchain opens up many opportunities for the profession of an accountant and the skills of the auditor will be focused more on concerning issues of a higher level. The methodological base of the study includes the theory of accounting and auditing, as well as the principles of operation of blockchain technologies in the aspect of their application in finance. The study overviews the main trends in the development of blockchain technology in accounting and auditing based on foreign scientific studies, as well as reviews of blockchain practices in articles by various scientists. The result of this research is an analysis of blockchain technologies in the finance field. The study depicts conclusions about the degree of applicability of this technology in the Russian Federation, reflects the main problems, risks and benefits from the introduction of this technology. This paper may promote an interest to the current professionals in the accounting and auditing field, as well as to professionals working in the range of building data exchange systems between employees involved in working with finances.

This paper suggests an approach to the semantic image analysis for application in computer vision systems. The aim of the work is to develop a method for automatically construction of a semantic model, that formalizes the spatial relationships between objects in the image and research thereof. A distinctive feature of this model is the detection of salient objects, due to which the construction algorithm analyzes significantly less relations between objects, which can greatly reduce the image processing time and the amount of resources spent for processing. Attention is paid to the selection of a neural network algorithm for object detection in an image, as a preliminary stage of model construction. Experiments were conducted on test datasets provided by Visual Genome database, developed by researchers from Stanford University to evaluate object detection algorithms, image captioning models, and other relevant image analysis tasks. When assessing the performance of the model, the accuracy of spatial relations recognition was evaluated. Further, the experiments on resulting model interpretation were conducted, namely image annotation, i.e. generating a textual description of the image content. The experimental results were compared with similar results obtained by means of the algorithm based on neural networks algorithm on the same dataset by other researchers, as well as by the author of this paper earlier. Up to 60 % improvement in image captioning quality (according to the METEOR metric) compared with neural network methods has been shown. In addition, the use of this model allows partial cleansing and normalization of data for training neural network architectures, which are widely used in image analysis among others. The prospects of using this technique in situational monitoring are considered. The disadvantages of this approach are some simplifications in the construction of the model, which will be taken into account in the further development of the model.

Hybrid electric powertrains in automotive applications aim to improve emissions and fuel economy with respect to conventional internal combustion engine vehicles. Variety of design scenarios need to be addressed in designing a hybrid electric vehicle to achieve desired design objectives such as fuel consumption and exhaust gas emissions. The work in this paper presents an analysis of the design objectives for an automobile powertrain with respect to different design scenarios, i. e. target drive cycle and degree of hybridization. Toward these ends, four powertrain configuration models (i. e. internal combustion engine, series, parallel and complex hybrid powertrain configurations) of a small vehicle (motorized three wheeler) are developed using Model Advisor software and simulated with varied drive cycles and degrees of hybridization. Firstly, the impact of vehicle power control strategy and operational characteristics of the different powertrain configurations are investigated with respect to exhaust gas emissions and fuel consumption. Secondly, the drive cycles are scaled according to kinetic intensity and the relationship between fuel consumption and drive cycles is assessed. Thirdly, three fuel consumption models are developed so that fuel consumption values for a real-world drive cycle may be predicted in regard to each powertrain configuration. The results show that when compared with a conventional powertrain fuel consumption is lower in hybrid vehicles. This work led to the surprisingly result showing higher CO emission levels with hybrid vehicles. Furthermore, fuel consumption of all four powertrains showed a strong correlation with kinetic intensity values of selected drive cycles. It was found that with varied drive cycles the average fuel advantage for each was: series 23 %, parallel 21 %, and complex hybrids 33 %, compared to an IC engine powertrain. The study reveals that performance of hybrid configurations vary significantly with drive cycle and degree of hybridization. The paper also suggests future areas of study.

The article explores the trinitarian systems used in the natural and technical sciences. Various types of trinitarian systems are considered. A systematic analysis of trinitarian systems was carried out. The article proves that the trinitarian system is the simplest complex system. The paper examines the relationship of trinitarian systems with the theory of categories. It is shown that the trinitarian system serves as the basis for categorical analysis. The paper proves that the trinitarian system is the simplest multigraph. The trinitarian system allows transforming spaces of different curvature into each other. The trinitarian system in linear systems defines a cyclicity, which can entail: development, degradation or bifurcation. Triangulation essentially develops a trinitarian approach and can be considered as the use of a trinitarian system to solve theoretical or technical problems in areas such as, for example, psychology, social sciences, politics, geometry, and ground surveying. The general conclusion is that the Trinitarian system is a universal instrument of cognition.

As a result of the research, the paper shows the essential need to take into account the social attributes of processes and phenomena in economy. From the standpoint of the interdisciplinary approach at various levels of the system three-hierarchy (micro-meso-macro) in economy, the following characteristics of social attributes are considered: “economic agent”, “expectations of the economic agent” and “preferences of the economic agent” taking into account their heteromorphism and heterogeneity, “intersubjective relations in economy”, “trust” between economic agents, “institutions”. The conclusions made as a result of the study make it possible to formulate the concept of selecting tools for economic and mathematical modeling of processes and phenomena at various levels of the system three-hierarchy (micro-meso-macro) in economy. Further studies will make it possible to select the most relevant tools for each level of the system three-hierarchy from the numerous apparatus used to model processes and phenomena in economy taking into account the concept proposed in this paper.

The purpose of this article is to study possible directions and ways of developing human resources for the transition to digital economy using the potential of new technological solutions. The paper demonstrates the relationship of the Fourth industrial revolution and changes in the development of human resources, identifies key areas of the impact of digitalization processes on human resources, including the transformation of the structure of demand in the labor market changing the format of employment of workers and the emergence of new models of work changing the content of work, as well as changing the ratio of the importance of hard skills and soft skills. With this in mind, the important components of developing human resources in digital economy are identified, the emphasis is placed on the role of the education system in this process, covering the following aspects: creating a system of new professions, competencies and standards in correspondence with appropriate educational programs; incorporating innovative educational technologies into the educational process in order to develop a set of soft skills; creating a “smart” education system using intelligent ICT solutions affecting the content and process components of learning as key components of developing human resources. The paper determines the feasibility of implementing the proposed solutions on the basis of the partnership between educational institutions, public authorities and business.

Introduction.The paper deals with traffic light regulation. This task is always relevant. Thus, even for an ordinary intersection, depending on the intensity of traffic flows, the control cycles should differ significantly. This paper discusses all kinds of systems, namely, two-phase, three-phase, four-phase and others. In addition to solving optimization problems of regulation the authors propose to use the device managed network, which allows setting the configuration of the transport network as the base graph of the managed network, and then based on the parameterization of the graph of the throughput ability of the network to solve the optimization problem of selecting the control traffic and pedestrian flow.Methods and materials. For solving the problem of traffic management on the road network, the authors proposed to use the mechanisms of managed networks. As a result, the authors presented a technique based on the calculation of saturation flows, the main characteristic of the control technique, which was activated when there were no requests from the transport detectors to turn by the green signal.Results.The authors constructed a generalized simulation model of control phases of regulation based on the usage of controlled networks, depending on the intensity of traffic flows and formed a method of selecting modes of traffic lights for different traffic situations.Discussion and conclusions.The solution of the problem of traffic light regulation significantly affects the traffic management efficiency. The authors determine the main parameters based on the analysis of traffic light control methods. As a result of the calculation of the saturation flow and information about the intensity of traffic, the authors form the method of selecting the necessary modes of the phosphor object’s operation.The authors have read and approved the final manuscript. Financial transparency: the authors have no financial interest in the presented materials or methods. There is no conflict of interest.

Introduction. The paper considers improving the management quality of an educational organization through automating the personalized data collection, storage and ranking. The authors have developed a module of the university corporate system, an ePortfolio of students, which implements a multicriteria optimization method for calculating the students’ rating on the basis of the collected and stored data. The study object is multicriteria ranking methods. The subject of the study is the automated calculation of student’s rating within the electronic portfolio. The study objective is to develop tools for collecting, storing and processing data on individual achievements of students and the implementation of the mathematical method of multicriteria optimization for ranking students on the basis of the portfolio data. Practical implications include development of a tool for an effective management of the educational process.Materials and Methods. A prototype module of the university corporate system “ePortfolio” on the platform of 1C: Enterprise 8.3 is presented. To rank students, a special case of the alternative ranking method is implemented in the block of the data analysis module – pairwise comparison in order of their relative importance. At that, a unified scale of relations was used.Research Results. The authors described the scheme of the information system (IS) operation “ePortfolio”, presented a process interaction pattern for the portfolio formation, as well as a diagram of business processes under calculating an individual rating. A fragment of the sample is shown on which the performance of the multicriteria optimization block has been tested. The criteria of the calculations are described, as well as the rule of screening alternatives for solving for the optimum.Discussion and Conclusion. The paper presents the results of the IS block operation on ranking a list of students. The calculation results coincide with the practical data.

Introduction. Hole details are quite widely used in structures of construction and road machines. The specialists apply boring for draft, semi-fair, and in some cases for fair processing of such surfaces. This type of processing is often followed by the negative nature of oscillatory processes that leads to decrease in accuracy and in the surface quality. The paper studies the possibility of the calculation method’s usage in oscillatory processes, which allows assigning the cutting modes by providing required output parameters.Materials and methods. The authors used the double-support beam as a design model of a boring cutter. The solution of the fluctuations’ modeling came down to definition of point movements, which corresponded to cutter top (points of application equally effective cutting forces). The authors made the definition of movements with use of Mor integrals. Therefore, the paper considered the impact of chip formation and separation due to perturbing forces.Results. The authors carried out the calculation of forces’ values in cutting with use of the degree dependences. Moreover, the authors accepted the formation’s frequency as the frequency of the perturbing influenced structure. The frequency of the chip formation was defined on the basis of estimated dependences, which connected parameters of the tool, the cut-off layer and modes of cutting. As a result, the author received the implementations of oscillatory processes and studied the influence of different factors on vibration amplitude.Discussion and conclusions. The authors make assessment of the received results’ adequacy by comparison with experimental data. The error doesn’t exceed 20%. The developed model considers geometrical parameters of the tool (a departure, plate corners, etc.), the modes of cutting both mechanical properties of the processed material and parameters of the chip formation. The model can be used both at design of boring operations and by optimization of the cutting modes for the purpose of productivity increase.

Introduction.Since the second half of the 20th century the safety in the automotive industry has been bringing to the forefront. Therefore, researches pay special attention to stability and controllability. These properties increase in a variety of ways, one of which is using of the four-wheel steering system (4WS). Foreign literature presents technical solutions on the example of sport cars and some Japanese models.Materials and methods.The paper provided an analysis of the four-wheeled steering passenger car’s kinematics. The authors considered the turning geometry with positive and negative steering angles of rear axle, on the basis of which the researches proposed calculation formulas for determining the turning radius of the car and the angles of the wheels’ rotation. The kinematic relations used in designing a steering system with four steered wheels.Results.The authors on the example of Volkswagen Polo calculated the turning radius and controllability depending on the steering wheels’ angles of the front and rear axles. As a result, the paper demonstrated the change in parameters and the effect on the safety and handling of the vehicle. The authors also highlighted the advantages of using a four-wheeled steering system.

Introduction. Perfect polyphase unimodular sequences, i. e. sequences with ideal periodic autocorrelation and single amplitude of symbols are widely used in modern radio communications and radar. A special place among them is occupied by perfect ternary sequences (PTSs) with elements {–1, 0, 1}. In fact, these are binary sequences with the alphabet {–1, 1}, but with zero symbols in some positions. It is known that PTSs are quite numerous and their length in comparison with perfect binary sequences is not limited from above. The charge for this is a peak factor greater than one, which causes energy losses in the receiver. A large number of research papers and books are devoted to the design of PTSs and the study of their properties. In particular, the handbook on sequence design by Fan and Darnell (1996) which provides an overview of the then known PTS families has become widely famous. However, over the past two decades, numerous new PTS families were discovered, some theorems on their existence were obtained, and connections were established between them and circulant weighing matrices. Therefore, there is a need for a new review of existing PTSs.Objective. The article is devoted to a retrospective review of existing PTSs and their generation devices.Materials and methods. Considered and analyzed domestic and foreign sources of information (books, journal papers, conference proceedings, patents).Results. Along with solving an informational bibliographic problem, the review shows the relationship between PTSs obtained at different times, their connection with circulant weighing matrices, and also describes the block diagrams of generators of some PTS families.Conclusion. A brief retrospective review of PTSs for their almost 60 years history is presented and the generators of some PTS families are considered. The results of the study are relevant for use in modern radio communications and radar systems and in particular, in CW and LPI radars.

A great attention has been recently paid to development of ultrasound technologies for treatment of blood vessels throughout the world. Authors of the paper have developed a new effective treatment method and ultrasound equipment that allow to carry out destruction of intravascular formations with simultaneous increase in elasticity of a vascular wall together with cardiologists from Belarusian Medical Academy of Postgraduate Education and Republican Scientific and Practical Center “Cardiology”. Advantages of the method are absence of necessity in surgical intervention, low probability of complications, low cost of treatment. The main component of the developed ultrasonic equipment is a tube-type stepped concentrator-waveguide having a spherical tip at a distal end with a single axial hole of 0.5 mm-diameter and three radial holes of 0.3 mmdiameter located at an angle of 120° relative to each other. The main effect for application of the concentratorwaveguide is achieved by ultrasonic vibromechanical action of a spherical tip on intravascular formation with subsequent removal of destruction products by their aspiration from a vascular bed. An additional effect is provided due to cavitation action on vascular formation and vessel walls by flow of fluid supplied via an internal cavity of the stepped concentratorwaveguide through the holes in the spherical tip. This contributes to a significant improvement in elastic properties of a vascular wall in atherosclerosis and diabetes. It is necessary to ensure high accuracy and quality of surfaces for the formed microholes in order to achieve maximum efficiency of the cavitation jet impact on intravascular formations and on the vascular wall. According to the analysis results on specific features of existing methods for small-diameter hole shaping, an electrochemical hole cutting method has been proposed which allows to obtain accurate micro-holes with a diameter of 0.3 mm and high surface quality in parts of small cross section and rigidity. The paper presents results of study on effect of electrochemical holes cutting parameters (voltage, concentration and consumption of electrolyte) on size and shape of the formed microholes. Main modes of electrochemical holes cutting process have been developed which allow to form micro-holes in a spherical tip of a tubular concentrator-waveguide with required accuracy, dimensions and shape.

When fighting against terrorism in modern armed conflicts, combat vehicles, including tanks, are widely used. To minimise own losses of vehicles and personnel for overthrowing enemy is a relevant task. To solve it, the paper considers certain events in the history of the Great Patriotic War, which are associated with battle of tanks that spring an ambush. A mathematical model of the battle is built. The state graph of the system is given. Using this graph, a probability of tank kills and a ratio of mathematical expectations of losses have been calculated. This mathematical model generalizes the models, previously published in this journal, based on the Markov chain apparatus. The paper gives an example of calculations for this model in the particular case in which experimental data are used as a basis. The ratios of mathematical expectations of losses of the warring parties are obtained. Further, we consider the mathematical models, in which it is assumed that probabilities for tank crews to provide operations of targets detection in firing are known. With technology development and its mathematical support it becomes increasingly more real. The formulas to obtain the probability of tank kills are given according to the graph of states using the known probabilities of transition from one state to another. In each of the three mathematical models under consideration there is a graph of the system state, which allows calculation of the tank kills probability. We have analysed the models to prove a significant dependence of the loss ratio of the warring parties on the number of firing positions used by the tank in ambush in case re-siting is unnoticeable for the enemy. The authors-considered models that use the examples of historical events confirm that the tactics of organising and conducting ambushes in tank battles can be successfully used nowadays, when the technology intensiveness of the opposing forces significantly grows. The obtained results can be applied to organise and conduct tank ambushes in modern armed conflicts and fight against terrorist army.

However, the ECP in its classical form has a number of significant drawbacks. One of them is a dependence of treatment modes and electrolyte compositions on the processed material. In addition, aggressive expensive electrolytes that require special technologies for disposal are used for ECP. Electrolytes in ECP often require heating to a temperature of 60–90 °C. Processing at such temperatures causes significant harm to the environment and production personnel. To eliminate the existing disadvantages of the ECP and expand its technological capabilities, a processing method with application of pulsed unipolar and bipolar modes has been proposed. As a result, fundamentally new processes of pulse ECP with a pulse duration of 0.05–20.00 ms have been developed. They provide a reduction of energy costs for the process and high efficiency of polishing in comparison with traditional DC polishing. The rate of smoothing micro-roughness of the treated surface related to the total metal removal is significantly increased. The use of pulse modes in comparison with traditional ECP allows processing in universal electrolytes of simple compositions based on sulfuric and orthophosphoric acids without addition of chromium anhydride. Application of the developed pulse modes, which will provide at low metal removal a significant change in surface roughness, is the most appropriate for the ECP of precise parts, products or parts of small cross-section and rigidity, such as medical devices for minimally invasive surgery, precision engineering parts, etc. The paper presents results of a study for influence of pulsed unipolar and bipolar ECP modes on the surface quality of stainless steel specimens, as well as a comparative analysis of the efficiency of using pulsed ECP modes instead of DC polishing. The technological parameters of ECP using pulsed modes, providing the highest quality surface polishing with high efficiency of micro-roughness smoothing and low energy consumption have been established in the paper.

Introduction. The paper deals with the results of the reliability of urban public passenger transport routes. One of the main objectives is to consider the indicators for assessing the reliability of the urban passenger transport system, which have not yet been used in Russian practice. The peculiarity of these indicators is that the initial information can be obtained on the basis of modern bus equipment (GLONASS/GPS). The possibility of using these indicators, as well as the development of scales of reliability levels at the moment is an important scientific problem.Materials and methods. The authors proposed modern indicators for assessing the reliability of urban passenger transport routes, such as the time index and the associated buffer time indicator. The authors used the methods of mathematical statistics to process the data on the duration of bus traffic.Results. The authors obtained the reliability characteristics of urban passenger routes. Moreover, the paper presented the comparison of the reliability values on the example of Irkutsk and Angarsk.Discussion and conclusions. The authors reveal the range of values of the time and buffer indices based on the data of route networks of two different cities. Therefore, the authors offer the estimation scale of the reliability levels on routes.

The paper presents a mathematical model and method for solving a wide class of problems in topological optimization of an adhesive joint to obtain an optimal microstructure and gradient properties in order to reduce the level of stresses arising from both thermal and mechanical loads therein.Adhesive joints have advantages over alternative bonding methods. The paper shows that the introduction of graduating properties in thickness or along the adhesive layer is the most promising strategy to optimize the adhesive. The approach is to modify the material properties or the geometry of the adhesive, varying along the joint.In all the papers known to authors, the shape of the elements to be joined, or the shape and location of the adhesive layer, were subject to optimization. The topological optimization methods to determine the optimal distribution / change of the gradient properties of the adhesive layer itself were not used.In the paper, the stresses arising in the solder joints are analyzed; it is shown that due to the small solder thickness, shear stresses are basic in it. The shear stresses are concentrated near the ends of the solder, and have the lowest values in the middle. The objective of the optimization problem is to reduce the peak values of the shear and peeling stresses in the solder layer. The topological optimization of the solder microstructure is to find the best distribution of a given amount of solder in the region in order to reach minimum peak values of stresses. The advantage of using topological optimization is that the microstructure of the solder should not be known a priori, and, thus, any designs can be optimized without first studying the effect of the original geometric parameters on the strength of the joint.The algorithm is implemented using the finite element method and the method of movable asymptotes. A number of examples are considered in order to obtain the solder microstructure to be optimal for reducing the peak values of shear stresses and delamination in a three-layer package.The results show that optimal microstructures significantly reduce peak stresses compared to a uniform layer. The obtained results reveal the potential of the developed algorithm and show that it can find practical use.