114 results
Search Results
2. Some Conisderations on RC Network (Part 1)
- Subjects
ZM2 ,通過周波数 ,位相差分波器 ,減衰函数 ,最小減衰量 ,CR ,利得偏差 ,濾波器 - Abstract
The Synthesis of the RC network has been made by Guillemin in 1949, but this does not represent the attenuation function explicitly, and the design of RC Network wants some considerations in the function. The auther have given some notes on this function in the Lecture-Meeting in May 1951 at Kyoto: the present paper is the same thing, including the Glass I (parallel T circuit) and the class II of the RC filter, in the sense of Tschebyscheff approximation. On the phase splitting-network with the RC-elements it will be reported in the next paper.
- Published
- 1951
3. On the Stability of Simultaneous Equation Computer
- Subjects
ZM2 ,解法機 ,方程式 ,平衡点 ,連立一次方程式 ,根 - Abstract
Solutions of problems arising in the field of engineering necessitate the solving of systems of linear simultaneous equations. Systems involving up to three equations can normally be solved quite readily by straight elimination methods. When the number of equations exceeds three, however, the solution is not so simple.An "Analogy Device" for solving simultaneous linear equations is treated in this paper. It utilizes a number of high gain amplifier with multi feed back system. The application of the feed back system always brings about the problem of stable operation. This stability problem has been thoroughly investigated in present paper., 工学の分野において表われる数値計算の問題の内で,困難なものの一つに連立一次方程式の根を求めるものがある。これは未知数の数が3元の辺りまでは筆算によってもある程度容易に求められるのであるが,それ以上未知数の数が増加すると計算に要する時間が加速度的に増してくるので,実際問題として不可能に近いものになってくる。そのために種々の解法機が提案され,製作されてきたが,大別して手動式のものと自動式のものとに分けることが出来る。手動式のものは手動制御によって逐次近似に求める解に近づけて行くものであり,自動式のもの自動制御によって与えられた方程式の満足する平衡点にまで持って行き,解を得ようとするものである。随って自動平衡式では解法機を動作させると自然に窮極の求める解まで行くので,その間に何等人間が干与する必要がなく便利なものであるが,解法機がある条件を満足すると,解は不安定となって定まらない。筆者がここで問題にするのはその点であって,解法機として真空管回路を用いmulti-feed backを行えば自動平衡式の解法機を作ることが出来るが,この際,誤差を少くするために高増幅度の真空管を用いるので,自己発振を起す危険性が多分に出てくる。自己発振を起したのでは解は不安定となって定まらないのである。この点について研究した。
- Published
- 1953
4. 一般化されたブールマトリックスによる組合せ回路の設計
- Subjects
ZM2 ,逆マトリックスの定義 ,逆ブールマトリックス ,ブールマトリックス方程式 ,組合せ回路 ,組合せ回路の設計 ,ブールマトリックス ,Hardware_LOGICDESIGN - Abstract
This paper reports Combinational circuit design have input and output of the same signal or the prohibition signal. ln this paper, Soulution of Boolean equation are derived from defining the generalized inverse Boolean matrix. For examle, Design of excess-3 cord circuit, 2 out of 5 mark etc are described., 本論文では,逆マトリックスの定義を拡張した一般化した逆ブールマトリックスについて考察し,ブールマトリックス方程式により組合せ回路を構成する。
- Published
- 1969
5. Stresses in an Infinite Plate with Two Contacted Circular Holes under Two Concentrated Forces in the Vicinity of the Holes
- Subjects
ZM2 ,フーリエ積分 ,機械学会論文集27巻179号 ,接触2円孔 ,フーリエ変換 ,2集中力 ,玉手統 ,吉川和男 ,無限板 ,応力 ,無限平板 - Abstract
The theoretical solutions cf the stresses in an infinite plate with the hole under uniform loading have been solved in a lot of cases by the numerous researchers, and the stress concentration factor along tbe hole has been well known. But there are many cases, in which the plate is loaded by the bolts, the rivets or the weldings in the vicinity of the hole. Then the stress distribution and the stress concentration factors along the hole are different to the uniform loading. In the previous papers, the stresses in an infinite plate with a circular or an intersected circular hole under two concentrated forces have been reported. This paper contains an exact two dimensional solution in the integral form for the stresses in an infinite plate with two contacted circular holes of equal size under two concentrated forces along the plane on the common tangential line of the holes. The basic stress function representing in the complex variables was transformed in the Fourier integrals using the formulas of the definite integral. A complete stress function in the plate with the hole was constructed in the form, in which a basic stress function was added to the auxiliary one. The curves of stress distribution and the rates of stress concentration were shown., 穴をもつ無限平板が穴の附近にボルト,鋲あるいは熔接等によって,集中力と見なし得る荷重を受ける場合はよく見られるところである。この平板の穴周辺の応力分布および応力集中率を明らかにする事は設計上また弾性学上に有意義であると思う。穴の形が完全円形あるいは円弧群より形成される場合は最も実際的である。著者はさきに1円孔,2円孔あるいは交叉2円孔をもつ無限平板が穴の附近に2集中力を受ける場合について報告をした。本論文はこれらと同様の解法により,接触する同大2円孔をもつ無限平板が共通接線上に穴に対称の位置に向きの反する同大2集中力を受ける場合を取扱った。この穴を有する無限平板が一様引張りを受ける問題は著者の研究がある。穴の形は円円座標によって表わし,複素変数で示された基礎応力関数を複素座標の平打移動と積分式によってフーリエ変換し,境界条件を満たす所要応力関数をフーリエ積分の形に求めた。数値計算により主として円孔周辺主応分布を求めた。
- Published
- 1961
6. Stress in an Infinite Plate under Two concentrated Forces in the Vicinity of the Holes (Supplements)
- Subjects
ZM2 ,2 次元光弾性実験 ,円弧 ,無限板の応力 ,円孔 ,円孔周辺主応力分布 ,無限板 ,応力 - Abstract
In the former papers, the stresses in an infinite plate with a circular or an intersected circular hole, or two contacted or two separated circular holes of equal radii under two concentrated forces of symmetry in the plate, have been reported. This paper reports a ploblem to determine the stresses in an infinite plate with an intersected or a contacted two circular holes under two concentrated forces in the plate, acting on a center line of the holes. The bipolar or the crowded circular coordinates were used in the solutions, and the basic stress functions were changed to the Fourier integrals. The calculations have been carried out for the values of the stress and the rates of the stress-concentrations, and the results of them have been published on the other paper., 円孔あるいは円弧によって形式された穴をもつ無限板数種について,一様荷重を対象とした従来の研究と異なり,穴の附近に2つの集中力を対称的にうける場合を数理弾性論的に解析し,前の論文に報告をした。本論文はこれに残された問題,すなわち交叉2円孔あるいは接触2円孔のある無限板において,円孔列中心線上に対称な2集中力が作用する場合を取扱ったものである。問題を平面弾性論における応力問題とし,2集中力をもつ無限板の基礎応力関数を複素変数で表わし,これを写像関数によって曲線座標に変換し,さらに適当な積分式を用いてフーリェ積分に変換した。基礎応力関数に附加する補助応力関数は前報と同様の形を用いた。また2次元光弾性実験を行い,円孔周辺主応力分布を求め,無限板としての理論値と比較した。
- Published
- 1962
7. Drawing up shear stress-strain graphs of Cr steel and high Mn steel in high temperature
- Subjects
ZM2 ,クローム鋼 ,高温捩り試験 ,高マンガン鋼 ,剪断応力歪線図 - Abstract
The author previotlsly published the paper with respect to shear stress-strain graphs of mild steel. In this paper, graphs of Cr steel and high Mn steel in high temperature--300℃ 400℃, 5000℃ and 600℃--are treated., 高温切削に於ける被削材の適性に関する問題を研究して行くには,被削材の金属組織の変化や機械的性質等を知ることが必要となってくる。そこで先に報告した軟鋼に関する実験に引続いてこの実験を行い,機械的性質の中の高温に於ける被削材の剪断応力の変化状態を求めた。
- Published
- 1957
8. Statistical Properties of the Fluctuation of Source Voltage
- Subjects
ZM2 ,自動制御系 ,相関函数 ,電源電圧変動 ,スペクトル密度 - Abstract
In ths paper there has been treated the flucutation of source voltage. This can be consideerd a stationary time series. The correlaiton function was determined on graph paper from data of observations. and from this the spectral density function was also dervied. These are very imporatnt means for the statistical dse ign of automatic control systems., 近年自動制御系の解析の手法の中へ確率的な考えが取り入れられ注目をうける様になってきた。即ち系に加えられる入力や外乱が確定的な単一画数でなくて不規則な時系列となっている様な場合である。不規則な変化をする入力や外乱の例は航空機に当る突風,複雑な変化をする発電機負荷,制御回路の各部に発生する雑音,レーダー電波の変動など種々のものがあげられるが,本稿で問題にしようとする電源電圧の変動もやはりこれに属するものと考えられる。この様な変化は時間に対する既知の単一函数として表わすことが出来ないし,直接にFourier変換やLaplace変換を施す普通の手段では処理することは出来ないので,これを部分振動に分けて平均の電力の周波数分布即ちスぺクトル密度を求めてこれによって問題を処理するのである。ここでは電源電圧変動の統計的性質即ち相関函数とスペクトル密度を求めたので報告する。
- Published
- 1956
9. Application of Holographic Interferometry for Deformation Problems (Check Base Gauge Method)
- Subjects
ZM2 ,Check base g auge法 ,変形問題 ,ホログラフィ干渉法 ,チェックベースゲージ法 ,3次元的変形 - Abstract
This paper deals with the basic research of a material deformation by hlographic interferometry.For the purpose, simplified models were used. The authors paid attention to the fact that it was impossible to measure at the same time interference fringes of different type localization, and made possible to measure them quantitatively by the check base gauge method.In addition, the explanation about holography is supplemented., 写真などによる強度分布の記録しか可能でなかった光学の分野に,物体から出る光の複素振幅分布を忠実に写真に記録し,それから再生像を作るという画期的な原理が確立され,ホログラフィの名称で研究されつつある。このホログラフィの工学への応用として,ホログラフィ干渉と呼ばれる興味ある分野の実現をもたらした。ホログラフィ干渉は同一物体を透過または反射する波面の時間的な変化を干渉によって求めるのに最も適した方法で,拡散性の物体を用いてその変形の前後の反射波面を干渉させることにより波長程度の変形測定が可能である。この方法は,従来からあるモアレ縞干渉法に比して,微小変形の測定に適しており,物体変形の測定範囲を広げ精度指数も高くなる点で期待されている。本文では初めにホログラフィについての解説を加えた後,物体の自由表面変形を想定し,ホログラフィ干渉についての3次元的変形をモデル化して行なった基礎的な研究報告である。
- Published
- 1974
10. An Investigation of Air-leakage between Contact Surfaces of the Case in which Mild Steel was finished by the Methods of various work
- Subjects
ZM2 ,接触機構の理論解析 ,軟鋼材 ,押付面圧 ,表面あらさおうとつ ,突出部 ,相当すきま ,接触面間からの漏れ - Abstract
In the last reports, it had been described that the phenomenon of leakage between contact surfaces was radial, nearly radial and whirl flow, respectively, in the case in which the metal surface was finished by lapping, grinding and lathing.In this paper, the specimens which were finished by the methods of various work were examined by using mild steel. The results obtained can be summarized as follows: (1) The analytical values of equivalent gap were in agreement with the experimental values with deviation about 6%. (2) The characteristic curves of parameters a and b listed in the 2nd report can be applied to mild steel., 管フランジの合わせ面のように,金属接触面問からの流体漏れをできるだけ押えることを必要とする機械要素部品は数多く存在する。その漏れ対策については,古くから多くの研究者によって材料力学的見地からの実験研究が実施され,その結果はDIN ASME規格の制定となり,なお,これらは我国のJIS規格のよりどころともなっている。ただ,これらの研究は接触面を平担な弾性体と仮定し,主として締付部位の形状および締付カ標準などを定めることに重点が置かれているので漏れ防止対策としては有益であるが,漏れ量を定量的に把握するには不十分のように考えられる。この点を考慮するに当って,固体加工表面に必ず存在する表面あらさおうとつ(以下,突出部という)の接触機構の理論解析を行ない,その結果,押付荷重によって変化する接触面間の漏れに対するすきま(以下,相当すきまという)の概念を樹立し,その数値を求める計算式を導いた。本文は,機械装置の接合部位に多く採用されている軟鋼材に対してラップ,研削および旋削の各種加工方法を施行した試料を表面あらさH≈Oの剛体と考えられる基礎盤(材質SKS2焼入れ,Hmax
- Published
- 1974
11. 遅延時間を利用した刺激強度変化検出神経回路網
- Subjects
抑制性シナプス後電位 ,シナプス後電位 ,ZM2 ,シナプス遅延 ,神経回路の構造 ,神経細胞モデル ,Quantitative Biology::Neurons and Cognition ,遅延時間 ,興奮性シナプス後電位 ,空間的加重性 ,刺激強度変化検出神経回路網 ,生物の神経系 - Abstract
In this paper, we describe about a hypothetical neural network which can detect the changes of the strength of stimuli. The network is composed of some neuron models which have time delays, spatial summation, and firing thrseholds., 生物の神経系は数多くの神経細胞から成っており,とりわけ脳においてはこれらが複雑にからみあい,知覚という非常に重要な情報処理が行なわれている。神経細胞自体はきわめて単純な機能しかそなえていないが,われわれ人間のような高度な知的活動をおこなうことができるのは,ほかならぬこの単純な神経細胞の組み合わせ,いわゆる回路に帰因するのである。このことはある知的活動を理解することは即,神経系各部の神経回路の構造を明らかにし,その結合の網を解いてゆくことにより神経集団としての神経系の機能を把握することになるのである。神経回路の構造を明らかにしていく上において,実際の脳について組織学的に調べることはその複雑さと,生体を対象とする研究がすべて直面する,生命活動を維持させ続けながら特性を把握せねばならないという困難さのため容易ではないと思われる。しかしながら,生体から分離された神経細胞単体の特性についてはHodgkinらの研究によってかなり明らかになっているので,その神経細胞がそなえている電気的活動性をモデル化した神経細胞モデルを用いて,生理学的な神経応答を示す際の神経回路の構造を推定しようという試みがなされてきている。本研究では特に,生物が感覚受容器で受け入れた刺激の強さが変化した時,その変化を検知できる,いわゆる微分的な機能をもつことに注目し,神経細胞モデルを用いてこの機能を実現できる神経回路網を構成しようとするものである。この場合,実際の知覚神経系では入力は周波数変調波として与えられ,刺激の強さに関する情報はパルス間隔の大小で与えられるので,このパルス間隔の大きさに変化がみられた時,その変化を示すパルスが出力として得られるよう回路を構成する。
- Published
- 1974
12. Considerations on delta modulation
- Subjects
ZM2 ,デルタ変調 ,ディジタル通信 ,圧伸1ピットデルタ変調方式 ,計算機シミュレーション ,圧伸1ピットデルタ変調装置 - Abstract
In delta modulation as well as PCM it is able to develope its S/N ratio by introducing the method of the companding.In this paper we discribe about the useflness of the amplitude weighting coefficient {1,1,2,4,9,・・・,9} which we proposed. This coefficient is especially superior to in both the noise characteristic and the following characteristic operating by the high frequecy input., ティジタル通信の代表的なものとして,パルス符号変調(pulse code modulation;以下PCMと略記)とデルタ変調(delta modulation;以下ΔMと略記)の二つをあげることができる。PCMは入力信号の符号化の過程において,量子化された各標本値の大きさに応じてnビット(例えば8ピット)のパルスを割り当て,変調系を構成する。これに対しΔMは連続する二つの標本値の差に1ビットのパルスを割り当てて変調系を構成するもので,PCMに比べ標本化周波数f_sが高くなる欠点があるが,変調器が著しく簡単となる利点がある。PCMでは量子化の過程で圧伸を行なうことによってS/N比の改善を行なっているが,ΔMにおいてもその様な圧伸を導入することにより,TV画像信号伝送の分野において,PCM方式に匹敵する性能の向上をはかってきた。圧伸の方法に瞬時圧伸を用いた圧伸1ピットΔM方式は,入力信号の変化の大きさに応じてステップサイズΔを変え,低周波入力時のgranular(量子化)雑音並びに高周波入力時のslope overload(勾配過負荷)雑音を軽減する目的で考え出された方式で,その振幅荷重係数{U_1,U_2,......,U_n}としては,安定性の立場から U_i≤^^^_U_j.......① を満たすものが望ましく,この条件のもとで{1,1,2,3,5,......5}(係数II)の方式が最も有効あることが報告されている。しかしながら高周波入力時のslope overload雑音特性を改善する見地からは,最大量子化ステップU_(=U_n)をできるだけ大きくすることが望ましく,著者等は振幅荷量係数{1,1,2,4,9,1.....,9}(係数I)の方式を考えた。この方式は安定条件式①を満たさず不安定性が懸念されるが,その不安定機構を解明した結果,不安定な振動を生ずることは極めてまれで,実用上ほとんど問題がないことが分かった。そこで実験装置を試作し,上記二つの方式の比較を中心に種々の実験・検討を行なったので,その結果をここに報告する。
- Published
- 1974
13. タービュレンスプロモーターによる対流熱伝達 (第1報 電気化学的測定法及び平均伝熱係数の影響)
- Subjects
Physics::Fluid Dynamics ,電気化学的測定法 ,ZM2 ,平均伝熱係数の影響 ,摩擦損失 ,伝熱係数 ,電気化学的方法 ,物質移動係数 ,アナロジー ,タービュレンスプロモーター ,対流熱伝達 ,アルカリ電解液 - Abstract
In order to study transport phenomena between solid and liquid, the electrochemical method is frequently used. This makes it possible to measure not only the average value but also the local value of mass transfer coefficient and of shearing stress at a liquid-solid interface. From the limiting current density at the cathode, the transfer rate of mass or momentum can be calculated. The mass transfer obtained by this method can be correlated with heat transfer by the analogy between both transport phenomena.In this paper, glass rodes 10mm. and 15mm. in diameter are used as turbulence promotors on the wall surface of a duct (100 X 30mm.). The average transfer coefficients on the wall surface without and with turbulence promotor are obtained by the electrochemical method. Maximum ratios for both promotors occur at a pitch to height ratio (P/D_p) of about 7, and transition region Reynold's no. of about 3,000. Though friction factors depend on height ratio and Reynold's no., they increase more than 10 times., 伝熱係数の増進は工業用水の不足対策,高温高熱流束の熱除去あるいはコンパクト熱交換器の設計等において重要視すべき課題である。流路内の伝熱係数を増進させるには強制的に乱流強度を大きくし境膜を薄くすればよく,そのために流路内にタービュレンスプロモーター(乱流促進体)の設置がしばしば考えられる。タービュレンスプロモーターには,1.流路内の主流中にねじり板あるいはらせん板を設置して主流を旋回させるもの 2.主流中に物体(格子,網など)を設置して主流を撹乱させるもの 3.伝熱面を粗面にしたり,突起物あるいはみぞを設置して境界層を撹乱させるものなどがある。これらのタービュレンスプロモーターを用いた伝熱に関する報告は数多くあるが,流体としては空気の場合が大部分を占めている。これは,空気の熱伝達率が小さく伝熱面積が大きくなるのでその改良のために考え出されたからである。ところが高温高熱流束の除熱には空気は不向きであり,実用的には効率等の観点から液体の使用が望ましく,本研究では流体として液体を用い,タービュレンスプロモーターによる影響を調べる。液体にはアルカリ電解液を用い,伝熱実験より精度の高い電気化学的方法により物質移動係数を求め,アナロジーより伝熱係数を求める方法をとった。タービュレンスプロモーターには主流方向と直角に丸棒をおき,流路底面の境界層を撹乱させる方法を選んだ。そのピッチ,高さ,径等による伝熱係数に与える影響を調べた。また,その時の摩擦損失をも調べた。
- Published
- 1974
14. On the Plant Design for the Industrial waste and Sewage Disposal
- Subjects
ZM2 ,消毒 ,河川の水質保全 ,プラントの設計 ,中和 ,産業廃水 ,沈降分離 ,廃水廃液 ,廃下水処理プラント設計 ,設計 ,下水し尿処理問題 ,下水処理装置 ,櫨過 ,放流 ,薬剤添加 ,乾燥 - Abstract
The graphical computation on the desiglling of the plant for the industrial waste and sewage disposal with the thickner, the oliver filter and the rotary dryer, is described in this paper., 最近工場における廃水廃液,都市の下水し尿処理問題が大きく叫ばれ,一方河川の水質保全に関する諾対策が講ぜられつつあることは衛生の見地より誠に喜ばしきことである。これらの処理方法は処理物質の性状に即応して適当な処理方法を採用すべきであるがこれを分類すると,物理的方法,化学的方法,並びに生物的方法に大別される。何れの方法によるもこれらの処理設備プラントの適切なる設計計画が望ましいものである。筆者等は図らずもこれらの処理についての計画面に参与する機会を得たのでこれらの問題につき若干調査研究することができた。茲では一つの他学処理方式として薬剤添加,沈降分離,濾過,乾燥,消毒,中和,放流という一つのプラントの設計について図式的に考察したところを述べることにしたい。各個々の操作については実験資料を得た上で考察することにし次の機会に報告することにしたい。
- Published
- 1960
15. Approximate Transfer Function of Dead Time (Continued)
- Subjects
ZM2 ,自動制御系 ,時間領域での解析 ,むだ時間 ,近似伝達関数 - Abstract
The transfer function of dead time is as is well known given by exponential function. When this exists in automatic control system, the theoretical treatment becomes very difficult. Therefore, this is expanded in rational series function and cut off by several terms. In this paper, the behaviors of these approximate transfer functions are verified theoretically and experimentally (using electronic analog computer)., 近似伝達関数についての周波数領域での検討の結果はすでに『富山大学工学部紀要』第13巻第1,2号で発表ずみである。したがって,今回は時間領域での解析を試みる。
- Published
- 1963
16. Simple Current Diagram Method for Calculating Characteristics of the Deep Slot squrrel Cage Induction Motor considering the Effects of Magnetic Saturation due to the Load Current
- Subjects
ZM2 ,負荷電流による磁気飽和 ,深みぞかご形誘導電動機 ,簡易電流線図法 ,特性算定簡易電流線図法 ,JEC-37 ,相似拘束等価巻線インピーダンスベクトル軌跡 - Abstract
Considering the effects of the magnetic saturration caused by the load current, current diagram methods for calculating charaeteristics of the ordinary squrrel-cage and that of the special squrrel-cage induction motors were established, and reported already. But it was impossible to apply them for the case of the deep-slot squrrel-cage induction motors with the slot-depth larger than 2 cm, because, in this case, the locus of the locked equivalent winding impeadamce phasor was not reprensented exactlly. Using Dr. M. Norman's theory, we could established the current diiagram method which was appropriative for this case. So, in this paper we report the new method that was devised for practical use. Moreover, it would be noted that this new method has higher accuracy than the conventional method by making a connparison between the results obtained by each of them., 先に負荷電流による磁気飽和の影響を考慮した誘導電動機の動特性算定電流線図を普通かご形と特殊かご形誘導電動機の場合について設定したが,スロット深さ2cmをこえるものは未設定である。これはこの場合の拘束等価巻線インピーダンスベクトル軌跡を正確に決定できなかったからである。この理由から,Norman氏の方法を用いてこの軌跡を考察し,負荷電流による磁気飽和の影響を考慮した深みぞかご形誘導電動機の特性算定電流線図法を設定するとともに,さらに実用化を目的として簡易電流線図法を設定した結果,簡易法にもかかわらず現行法に比べて非常に精度が高く,かつ,きわめて簡単な手法であることから従来の頻雑な方法から解放されて有効に使用できることを知ったので報告する。
- Published
- 1969
17. Size reduction ratio and limit of short time running duty induction motor
- Subjects
ZM2 ,体格縮少可能割合 ,小形短時間定格誘導電動機 ,誘導電動機 ,短時間定格 ,体格縮小限界 - Abstract
This paper shows the method which decides a size of short time running duty induction motor from continuous running one which is same capacity, and shows there must be size reduction limit to keep the maximum-torque required., 誘導電動機(以下,IMと略記する)の設計について多くの文献が発表されているが,いずれも連続定格IMを対象としており,短時間定格IMに関するものは温度上昇特性を概念的に述べたものが多く,具体的に設計資料となる研究発表はない。その意味に於て連続定格機より短時間定格の理由で体格を縮少した場合,定格時間と体格縮少可能割合及び縮少限界を求めてみた。
- Published
- 1964
18. Studies on Static Electrification Phenomena of Liquid
- Subjects
ZM2 ,静電気 ,残留静電気 ,Mysterious fire ,給油 ,加圧式濾過装置 ,液体の帯電現象 ,引火災害 ,帯電現象 ,Volume charge - Abstract
The dangerous fire hazard, which is considerd by the ignition of the spark discharge of the static electricity in the treatment of the flamable liquid as gasoline and benzol etc, was reported, frequently. This paper studies the static electrification phenomena of the transformer oil which is circulated by the gear pump through the filter press, as the fundamental research on the electrification by the fluid friction., 周知の如く可燃性の非電導性固体,粉体,液体はその生産又は処理工程において静電気が発生し,種々の障害を惹起し又放電火花による引火災害所謂Mysterious fireが多くなる傾向がある。筆者はかつて〓(土へんに圭)化石灰粉を中心として各種粉体の摩擦帯電現象について実験し,帯電による爆発の可能性は充分起りうるという結論を得た。液体については,この種原因と認められている公知のものには,25年3月九州某工場でベンゾールタンクにベンゾールを圧送作業中におけるタンクの爆発,28年8月静岡市某ガソリンスタンドでドラム缶からガソリンを地下タンクに補給作業中の引火災害,29年11月浜松市某ガソリンスタンドでピニールホースによるガソリン補給中の引火火災,又34年5月勝山市某ガソリンスタンドでタンクローレイより地下タンクに給油中の引火火災等があり,小被害を加えると相当頻出していると指定され近時可燃性液体の処理工程の量産と普及に伴い,この種放電火花による災害が益々多くなる傾向がある。液体が流動する際,その比抵抗が10^Ωcm以上では帯電するが,10^9Ωcmでは漏洩のため帯電は認められないと云われるので,本実験に用いた液体にはガソリン,ベンゾールの如き可燃性液体は引火の危険があるので,便宜上変圧器油を用い,給油装置として加圧式濾過機を使用し,その流動摩擦による帯電現象を究明する第一歩として行った実験で,本報告はその測定の経過概要である。
- Published
- 1960
19. Observation of Ferroelectric Domain Structures of Tri-Glycine Sulfate Using a Scanning Electron Microscope
- Subjects
アニーリング ,ZM2 ,飽和水溶液徐冷法 ,走査型電子顕微鏡 ,強誘電分域 ,強誘電体の分域 ,分域観察 ,硫酸グリシン ,強誘電分域の観察 - Abstract
This paper reports some ferroelectric domain patterns of triglycine suJfate obtained by utilizing a scanning electron microscope. Covering the crystal surface with gold of 20--30Å in mean thickness by vacuum evaporation, clear secondary electron images showing ferroelectric domains were obtained. It is supposed that some parts of the electric and thermal currents flow in the ev aporated gold, and protect the specimen from the charge-up and destruction. It has been found that, annealing the crystal above the Curie point, the lenticular domain structure changed into the fine lamellar one., 強誘電体の分域(ドメイン)を観察する一般的方法として,これまでエッチング法,帯電粒子法(コロイド法・装飾法・露j商法),偏光顕微鏡や電子顕微鏡による方法,さらにはX線回析顕微法等多くの報告がなされている。これらの方法にはそれぞれ一長一短があり,また強誘電体の種類によっては使用不可能なものもある。例えばここでとりあげた硫酸グリシン(TGS)の場合,逆方向を向いた分域のそれぞれの光学的弾性軸が一致するので偏光顕微鏡による観察は不可能である。また薄膜を作製するのが困難であるため透過型電子顕微鏡による方法もまず不可能と思われる。一般的にいってエッチング法及ぴ帯電粒子法は静的な分域構造を示すにすぎず,何らかの外部因子の変化に対する分域の動的なふるまいをこれらの方法で得ることは極めて困難である。以上のような方法に加えて新しい方法として注目されているのが,エレクトロンミラーマイクロスコープ(EMM)及び走査型電子顕微鏡(SEM)による分域の観察である。これらはいずれも試料表面に電子線を照射し,表面電位による応答から分域構造を得ようとするものである。このうち走査型電子顕微鏡によるこれまでの報告例は,W0_3,BaTiO_3,SbSI及びTGSに対してBihanらによって行なわれたものである。彼らの報告では,走査型電子顕微鏡による分域観察の利点として,(1).分解能がかなり高い。 (2).被写体深度が深い。 (3).動的な分域のふるまいを観測できる可能性がある。 をあげている。しかし,SbSIやWO_3等のように比較的電気伝導度の高い物質に対しては極めて良い結果が得られているが,TGSのように電気伝導度が非常に小さく,しかも電子線照射によって破壊されやすい物質に対して安定で鮮明なdomain patternを得ることはかなり困難である。もちろん加速電庄をできるだけ低くしプロープ電流もできるだけ小さくすることによって像を得ることは可能であるが,結局は試料表面に電荷が蓄積するので像が安定でない。筆者は,TGS表面に金を薄く真空蒸着することによってこれらの難点をある程度克服し,かなり安定で鮮明な像を得ることができたのでそのいくつかを報告する。そしてアニーリングによる分域構造の変化についても簡単に報告する。
- Published
- 1973
20. Tables of the ber Function and the bei Function
- Subjects
バイ関数 ,ZM2 ,ベル関数 - Abstract
The tables of ber function and bei function are made by the electronic digital computer in the Toyama University computing center. Range of X is from 0 to 30, and step is 0.01. But the tables, 0.1 step, are shown in this paper., 本稿では,ベル関数およびバイ関数の表を示す。
- Published
- 1966
Discovery Service for Jio Institute Digital Library
For full access to our library's resources, please sign in.