Search

In the presence of completely dry soda lime volatile anaesthetics will decompose to carbon monoxide (CO). In an in vitro study, the absorbent (soda lime, ICI) was dried with a constant gas flow of 11/min oxygen for 120 h. The weight loss during the drying was 17.1%. Two vol% of halothane, enflurane or isoflurane in oxygen was administered with a constant flow of 0.51/min oxygen through the completely dry absorbent. Concentrations of gases were measured before and after the absorbent using mass spectrometry (MGA 1100, Perkin-Elmer) and an electrochemical NO monitor (Mini PAC CO, Dräger). The temperature inside the soda lime was monitored continuously. Shortly after adding the anaesthetic to the oxygen passing through the absorbent, carbon monoxide appeared in the outlet of the soda lime container. The measured peak concentrations varied around 450 ppm (halothane), 3500 ppm (enflurane) and 3800 ppm (isoflurane). The temperature inside the absorbent rose from the ambient temperature (19.8 degrees C) to a maximum of 52.1 degrees C during CO production and decreased when the CO production lowered after approximately 1 h (all anaesthetics). During CO production no measurable concentration of halothane left the absorber. After passing through the absorbent the concentrations of isoflurane and enflurane were slightly lower than the corresponding concentrations in the fresh gas measured before absorption. [ABSTRACT FROM AUTHOR]

It is a strange contradiction that increasingly sophisticated anaesthesia machines are developed meeting all requirements for rebreathing techniques and the highest safety standards, but the usual anaesthetic management is still based on the use of fresh gas flows that preclude substantial rebreathing. The advantages of rebreathing can only be realised if low-flow anesthesia techniques are adopted. Increasing acceptance of these methods is due to the availability of comprehensive anaesthetic gas monitoring. Different techniques of low-flow anaesthesia, the characteristic features, technical requirements, and considerations concerning their performance and contraindications are discussed. This paper presents a topic that is left unmentioned by most anaesthesia textbooks. The use of new inhalational anaesthetics such as desflurane that require comparatively high concentrations, or even xenon, will motivate to sparing use. Increasingly stringent health and safety regulations as well as sharpened ecological awareness will prompt anaesthetists to minimise all anaesthetic gas emission according to the possibilities of available equipment. Last but not least, the demand for economical working methods will be an argument for applying low-flow anaesthesia techniques. [ABSTRACT FROM AUTHOR]

The skill to safely manage the unexpectedly difficult airway is expected from every anaesthetist. The strategies to safely overcome this severe problem have to be adapted to the given equipment and the individual aptitude and skills of the respective colleague. The algorithms for management of the difficult airway should be as simple as possible, and one cannot assume that devices for fibre-optic intubation are available at every site. Indispensable, however, is the availability of face masks, naso- and oropharyngeal airways and laryngeal mask airways in different sizes at each induction site. This paper is especially devoted to recalling the Oxford non-kinking tube and its specific way of handling, as a lot of cases of unexpectedly difficult airway can be safely managed with this tool. Alternatives to safeguarding the difficult airway are the intubation laryngeal mask airway or the esophago-tracheal combitube. For managing the worst case, the "cannot ventilate - cannot intubate" disaster, instruments for percutaneous punction of the trachea and devices for oxygen insufflation must be readily available in every theatre.

Background: During general anaesthesia gas climate significantly is improved by performance of low flow techniques. Gas climatisation, however, markedly also will be influenced by the temperature loss at, and corresponding water condensation within the hoses, factors which are related to the technical design and material of the patient hose system. The objective of this prospective study was to investigate 1. how anaesthetic gas climatisation during minimal flow anaesthesia is influenced by the technical design of different breathing hose systems in clinical practice. 2. to investigate, whether a sufficient gas climatisation also can be gained with higher fresh gas flows if that hose system is used, proven beforehand to optimally warming and humidifying the anaesthetic gases., Methods: Three different systems, a conventional two-limb hosing consisting of smooth silicone hoses, a coaxial hosing, and a hosing consisting of actively heated breathing hoses, attached to a Dräger Cicero EM anaesthesia machine, were used during minimal flow anaesthesia with a fresh gas flow of 0.5 l/min. Gas temperature and absolute humidity were measured at the tapered connection between the inspiratory limb and the breathing system as well as at its connection to the endotracheal tube. The best gas climatisation was observed if heated breathing hoses were used. Thus, using this hosing, additionally gas temperature and humidity in the inspiratory limb were taken at fresh gas flow rates of 1.0, 2.0 and 4.4 l/min respectively. Measurements were performed in all groups at all general anaesthesias lasting at least 45 minutes during the lists of eight different days each., Results: In minimal flow anaesthesia, with all hose systems likewise, generally an absolute humidity between 17 to 30 mgH2O/l is reached at the endotracheal tube's connector during the course of the list. Only in the first cases of the day there was a short delay of 15 to 30 minutes before reaching a humidity of at least 17 mgH2O/l. Only with heated hoses, however, humidity frequently even exceeded 30 mgH2O/l. If conventional or coaxial hosings were used, during minimal flow anaesthesia gas temperatures in an acceptable range between 23 to 30 degrees C were measured at the tube connector. With heated hoses, however, warming of the gases was excellent with gas temperatures between 28 to 32 degrees C. In minimal flow anaesthesia climatisation of the anaesthetic gases proved to be best if heated hoses were used. Thus, using heated hose systems another three trials with increasing fresh gas flow rates of 1.0, 2.0 and 4.4 l/min respectively were performed. Whereas climatisation of the anaesthetic gases still was found to be optimal with a fresh gas flow of 1.0 l/min, the humidity dropped drastically to values lower than 17 mgH2O/l at 2.0 l/min and even down to 10 mgH2O/l at a flow rate of 4.4 l/min. Gas temperatures, however, turned out to be independent of the flow and remained at 28-32 degrees C, even at a flow as high as 4.4 l/min., Conclusions: Using conventional hose systems and coaxial hosings acceptable, but not optimal climatisation of the anaesthetic gases can be gained if minimal flow anaesthesia is performed. The use of a coaxial hose system seems to lead to improved climatisation in long lasting procedures only. In routine clinical practice, however, conventional and coaxial hose systems are similar in respect to the climatisation of breathing gases. Heated breathing hoses performed markedly better in terms of climatisation of the breathing gas than the coaxial and the conventional hose system. With this hosing not only sufficient but optimal moisture and temperature values are realized. Optimal climatisation, however, only can be gained if low flow anesthetic techniques with fresh gas flows equal or less than 1 l/min are performed. With higher fresh gas flow rates the humidity decreases markedly while high gas temperatures are maintained. (ABSTRACT TRUNCATED)

The routine use of nitrous oxide as a component of the carrier gas has been unanimously called into question in recent surveys, in fact, its use is now recommended in indicated cases only. Whereas a lot of contraindications are listed in the surveys, precise definitions of justified indications are not given. In clinical routine practice, there are absolutely no problems in carrying out inhalational anaesthesia without nitrous oxide. The missing analgetic effect can be compensated for by moderately increasing the additively used amount of opioids, while the missing hypnotic effect can be achieved by raising the expired concentration of the inhalational anaesthetic by not more than 0.2-0.25 x MAC. Thus, when isoflurane is used, an expired concentration of 1.2 vol% is desired, in the case of sevoflurane of 2.2 vol% and with desflurane of 5.0 vol%. In addition, doing without nitrous oxide facilitates the performance of low flow anaesthetic techniques considerably. Since the patient only inhales oxygen and the volatile anaesthetic, the total gas uptake is reduced significantly. Washing out nitrogen is no longer necessary. This means that the initial phase of low flow anaesthesia, during which high fresh gas flows have to be used, can be kept short. Its duration is now determined by the wash-in of the volatile anaesthetic. Since there is no uptake of nitrous oxide, a considerably greater volume of gas is circulating within the breathing system, minimizing the possibility of accidental gas volume deficiency. Thus, if anaesthesia machines with highly gas-tight breathing systems are used, even the performance of non-quantitative closed system anaesthesia becomes possible in routine clinical practice. The carrier gas flow can be reduced to just that amount of oxygen which is really taken up by the patient. This oxygen volume can be roughly calculated by applying the Brody's formula. Using fresh gas flows as low as 0.25 l/min, however, will result in a significant decrease of the output of conventional vaporizers outside the circuit. Thus, it becomes nearly impossible to maintain an expired isoflurane concentration of 1.2 vol%. With respect to their pharmcokinetic properties, the newer low soluble volatile agents sevoflurane and desflurane are better suited for use with flows corresponding to the basal oxygen uptake. Our own clinical experience, gained in the last six months from a trial involving over 1,800 patients, shows that the increase in opioid consumption resulted in additional costs of about 0.25-0.50 DM per patient. The increased concentration of inhalational agents brought additional costs of 3.00 to 5.00 DM for a two-hour anaesthesia. On the other hand, doing without nitrous oxide saved 2.61 DM per one-hour anaesthesia, whereby our consumption of nitrous oxide is extremely low as minimal flow anaesthesia is performed consistently. Furthermore, these calculations disregard the cost of the technical maintenance fo the central gas piping system and of the regular measurement of workplace contamination with nitrous oxide by a certified institute, which in Germany, ad least, is obligatory. The additional costs of nitrous oxide-free inhalational anaesthesia seem to be balanced by the savings. Given the numerous justified arguments against the routine use of nitrous oxide, the lack of precisely-defined indications and the clinical experience showing that doing without nitrous oxide is uncomplicated, self-financing and ecologically beneficial, the use of nitrous oxide should be given up completely.

Objectives: Due to its low solubility and negligible metabolism, desflurane is assumed to be especially suitable for application by low-flow anaesthetic techniques. The aim of this clinical investigation was the development of a standardised dosing scheme for low-flow and minimal-flow desflurane anaesthesia., Methods: One hundred six ASA status I-II patient were assigned to six groups according to the duration of the initial high-flow phase, fresh gas flow, and fresh-gas desflurane concentration. The median age, height, body weight, and constitution of the groups was comparable. After an initial high-flow phase using 4.4 l/min, the fresh gas flow was reduced to 0.5 l/min (minimal-flow anaesthesia) or 1.0 1/min (low-flow anaesthesia). Inspired nitrous oxide concentrations were maintained at 60% to 70%. Using different standardised schemes of vaporizer settings, inspired desflurane concentrations were applied in the range from 3.4% to 8.7%, i.e., between 1 and 1.5 MAC. Inspired and expired desflurane concentrations were measured continuously by the side-stream technique and recorded on-line. Venous blood samples were taken immediately prior to induction and 45 min after flow reduction for measurement of carboxyhaemoglobin (COHb) concentration)., Results: In the 10- to 15-min initial phase during which a high fresh gas flow of 4.4 l/min was used, the inspired desflurane concentration reached values in the range of 90%-95% of the fresh gas concentration. In low-flow anaesthesia this concentration could be maintained without any alteration of the vaporizer setting, whereas in minimal-flow anaesthesia with flow reduction the fresh gas concentration had to be increased by 1% to 2%: The quotient calculated by division of the inspired desflurane concentration by its fresh gas concentration (Q = CI/CF) ranges between 0.65 and 0.75 in animal-flow and between 0.80 and 0.85 in low-flow anaesthesia. If use was made of the wide output range of the desflurane vaporizer, the inspired concentration could be increased rapidly by about 5% in 8 min, although the flow was kept constant at 0.5 l/min. Compared with its value prior to induction (2.13 +/- 1.05%), the COHb concentration decreased statistically significantly by about 0.7% during the 1st hour of minimal-flow anaesthesia (1.42 +/- 1.01%). In no case was a COHb concentration observed that exceeded threatening or even toxic values, although the soda lime was changed routinely only once a week., Conclusions: The pharmacokinetic properties of desflurane, resulting in especially low individual uptake, and the wide output range of the vaporizer facilitate the use of low-flow anesthetic techniques in routine clinical practice. Even in minimal-flow anesthesia, the duration of the initial high-flow phase can be shortened to min. If the flow is reduced to 1 l/min, the inspired desflurane concentration achieved in the initial high-flow phase can be maintained without any alteration of the vaporizer setting. In minimal-flow anesthesia, however, with flow reduction to 0.5 l/min, the fresh gas concentration has to be increased to a value 1%-2% higher than the inspired nominal value. Due to the wide dialing range of the desflurane vaporizer, the amount of vapour delivered into the breathing system can be increased to about 110 ml/min even at a flow of 0.5 l/min. The large amount of agent that can be delivered into the system even under low-flow conditions, together with the very low individual uptake, results in a time-constant that is sufficient short for the clinically required rapid increase in inspired desflurane concentrations. The short time-constant of low-flow desflurane anaesthesia improves the control of the anaesthetic concentration. If all measures are taken to safely avoid inadvertent drying out of the soda lime, there is no evidence that low-flow anaesthesia with desflurane is liable to increase the risk of accidental carbon monoxide poisoning. (ABSTRACT TRUNCATED)

In the presence of completely dry soda lime volatile anaesthetics will decompose to carbon monoxide (CO). In an in vitro study, the absorbent (soda lime, ICI) was dried with a constant gas flow of 11/min oxygen for 120 h. The weight loss during the drying was 17.1%. Two vol% of halothane, enflurane or isoflurane in oxygen was administered with a constant flow of 0.51/min oxygen through the completely dry absorbent. Concentrations of gases were measured before and after the absorbent using mass spectrometry (MGA 1100, Perkin-Elmer) and an electrochemical NO monitor (Mini PAC CO, Dräger). The temperature inside the soda lime was monitored continuously. Shortly after adding the anaesthetic to the oxygen passing through the absorbent, carbon monoxide appeared in the outlet of the soda lime container. The measured peak concentrations varied around 450 ppm (halothane), 3500 ppm (enflurane) and 3800 ppm (isoflurane). The temperature inside the absorbent rose from the ambient temperature (19.8 degrees C) to a maximum of 52.1 degrees C during CO production and decreased when the CO production lowered after approximately 1 h (all anaesthetics). During CO production no measurable concentration of halothane left the absorber. After passing through the absorbent the concentrations of isoflurane and enflurane were slightly lower than the corresponding concentrations in the fresh gas measured before absorption.

As early as in 1850 (only 4 years after the first clinical performance of ether anaesthesia by W. T. G. Morton on 16 October 1846) John Snow recognised that ether and chloroform were exhaled unchanged with the expired air. To reuse these unchanged vapours in the following inspiration and thereby prolonging the narcotic effect of a given amount of anaesthetic vapour, he converted his ether inhaler into a To-and-Fro Rebreathing System: The apparatus was equipped with a facemask without an expiratory valve and a large reservoir bag containing pure oxygen; an aqueous solution of caustic potash was used as CO2 absorbent. In several experiments, performed on himself, Snow succeeded to demonstrate that rebreathing of the exhaled vapours was possible following carbon dioxide absorption, and that it resulted in a pronounced prolongation of the narcotic effects of the volatile anaesthetics. Furthermore, Snow performed experiments on animals using a closed system for evaluating the carbon dioxide production during anaesthesia. It is all the more worthwhile to introduce Snow's publications on these topics, as, despite their extraordinary theoretical and practical significance, they remained nearly unnoticed. Even in the fundamental articles by D. Jackson and R. Waters, both being the respected protagonists of the rebreathing technique in anaesthesia, the Snow papers remained uncited.

A new simple gag is presented securing the width of the tube of the laryngeal mask. The device is a 45 degrees-angled, u-shaped, synthetic-coated aluminium rod. This gag, while being additionally an aid to ensure the proper position of the laryngeal mask, is easy to handle and can be re-used after disinfection. Due to its rounded shape and the soft synthetic coating, accidental damage of the teeth seems to be nearly impossible.

It is a strange contradiction that increasingly sophisticated anaesthesia machines are developed meeting all requirements for rebreathing techniques and the highest safety standards, but the usual anaesthetic management is still based on the use of fresh gas flows that preclude substantial rebreathing. The advantages of rebreathing can only be realised if low-flow anesthesia techniques are adopted. Increasing acceptance of these methods is due to the availability of comprehensive anaesthetic gas monitoring. Different techniques of low-flow anaesthesia, the characteristic features, technical requirements, and considerations concerning their performance and contraindications are discussed. This paper presents a topic that is left unmentioned by most anaesthesia textbooks. The use of new inhalational anaesthetics such as desflurane that require comparatively high concentrations, or even xenon, will motivate to sparing use. Increasingly stringent health and safety regulations as well as sharpened ecological awareness will prompt anaesthetists to minimise all anaesthetic gas emission according to the possibilities of available equipment. Last but not least, the demand for economical working methods will be an argument for applying low-flow anaesthesia techniques.

The utilisation time of carbon dioxide absorbers in anaesthesia textbooks is nearly identically specified to last about 5 hours. Therefore in most departments the soda lime of the absorbers is changed routinely on a daily schedule. As rebreathing volume increases considerably with fresh gas flow reduction, the question arises as to whether the soda lime should be changed at even shorter intervals--if low-flow anaesthesia is performed routinely--to to guarantee carbon dioxide absorption safely. In three anaesthesia machines with different technical properties the carbon dioxide absorbers were only changed when the inspiratory carbon dioxide concentration increased to 1 vol. %, indicating definite exhaustion of the soda lime. If a fresh gas flow of 4.4 l/min was used exclusively, utilisation times of 42.7 and 62.3 hours were measured using absorbers filled with 1 l of soda lime pellets, whereas a utilisation time of 98.7 hours was noted with a 1.5 l absorber, all values being surprisingly higher than the above-mentioned figure. If, however, minimal flow anaesthesia is performed routinely in clinical practice, the percentage of time in which the fresh gas flow can really be reduced to 0.5 l/min does not exceed 50 to 80%. Under these conditions the utilisation time of the absorbers decreases to between one half (1/2) and one quarter (1/4) of the utilisation time which can be gained if a flow of 4.4 l/min is used. Thus, the performance of minimal-flow anaesthesia increases the consumption of soda lime two- to fourfold.(ABSTRACT TRUNCATED AT 250 WORDS)

Continuous measurement and monitoring of the expiratory carbon dioxide concentration can be performed with modern measurement devices routinely without any problem today. After a short introduction to measurement techniques the comprehensive monitoring possibilities of this method are described by multiple examples. No only actual disturbances of the ventilation, the circulation and the metabolism, but also malfunction or inadequate control of the anaesthesia machine can be recognized without substantial time delay. But an actual alteration of the CO2 value necessitates careful analysis of the underlying problem which is greatly facilitated by a graphic display of the CO2 signal, the capnogram. The knowledge of possibly occurring artificial alterations of the CO2 measurement, which are demonstrated too, prevents dangerous misinterpretations. By continuous measurement of the expiratory CO2 concentration, not only can the ventilation parameters be set optimally, but multiple life threatening complications can be detected very early and corrected immediately. Thus, this monitoring technique essentially contributes to the patients safety during anaesthesia.

The majority of modern anaesthetic machines is designed for the rebreathing method. But frequently high fresh gas flows are employed, thus minimising the rebreathing fraction of expiratory gases. However, only by reducing the fresh gas flow substantially, the advantages of the rebreathing technique can be obtained. To evaluate the practicability of flow reduction, minimal flow anaesthesia was carried out with four different anaesthetic machines: AV 1 (Drägerwerk AG, Lübeck), ELSA (Gambro Engström AB, Bromma, Sweden), SULLA 808 V (Drägerwerk AG, Lübeck) und VIVOLEC (Hoyer Medizintechnik, Bremen). Fresh gas flow was reduced to 0.5 l/min after an initial phase of 15-20 min, during which the fresh gas flow was kept at a high level of 4.4 l/min. The minute volumes before and after fresh gas flow reduction were compared. The minute volume decreased markedly and significantly in the SULLA 808 group, whereas it remained nearly unchanged in the AV 1, the ELSA, and the VIVOLEC groups. The differences result from different modes of fresh gas delivery into the breathing circuit. If anaesthetic apparatus that maintain their tidal volume with different fresh gas flow rates are employed, rebreathing systems may be used judiciously by changing the fresh gas flow according to the individual uptake or any particular clinical requirement.

A clear understanding of technical details is essential for safe handling of anesthetic machines. Following the ideas of E.A. Ernst, it is suggested that anesthesia systems be differentiated according to the underlying principles of construction into rebreathing systems, flow- and valve-controlled non-rebreathing systems, and systems without reservoirs. This classification seems much clearer than the usual differentiation into closed, semiclosed, semiopen, and open systems, which is based upon functional criteria. Anesthesia systems must be understood as technical parts (hardware) of anesthetic machines with variable function according to the chosen fresh gas flow (software). An unequivocal characterization of an anesthetic system will only be possible if its technical properties are described together with the fresh gas flow used. Most anesthetic machines currently in use are equipped with a circle system and sophisticated monitoring, which is designed for the rebreathing technique. This technique can only be used advantageously, however, if the rebreathing system is used in conjunction with substantially reduced fresh gas flows.

"Postoperative hypalgesia" following electroacupuncture or electrostimulation anesthesia is considered to be a notable advantage of these techniques, which supports the thesis, that endorphines may be involved in the mechanism of pain relief by these methods. After establishing definitive criteria postoperative hypalgesia was observed in 50% of patients undergoing operations on the lumbar vertebral column with electroacupuncture. A comparative investigation using psychological tests showed, that these patients are more pain tolerant than those, in whom postoperative hypalgesia was not observed. Observation alone of the patients during the postoperative period is unreliable to assess real postoperative pain relief objectively. Exact documentation and critical proof of the phenomenon of "postoperative hypalgesia" must be emphasized. These may be possible essentials to establish optimal methods of electrostimulation -- anesthesia.

A new concept of anaesthesia in patients undergoing operations of the lumbar vertebral column is presented. Electrostimulation of four auricular acupuncture points is combined with controlled ventilation of nitrous-oxide oxygen mixture. This combination is comparable to similar anaesthesia procedures of other operative fields. In 30 patients the anaesthesia was performed as a "combined electrostimulationhypalgesia". In a control study of 30 similar patients a mixture of nitrous-oxide and oxygen only was used. For 120 min systolic and diastolic blood pressure as well as heart rate of both groups are measured and compared. The postoperative state as well as individual data from the patients are included in the investigation. The analgesia established by "combined electrostimulationhypalgesia" seems to be based essentially on the effect of nitrous-oxide as well as premedication, induction of anaesthesia, relaxation and kind of ventilation. Electrostimulation of auricular acupuncture points seems to induce stabilisation of the circulatory system. On account of our findings the relevance of electrostimulation in this method of anaesthesia must be judged very critically.

The stimulating impulses employed in electroacupuncture analgesia are of widely differing character and strength. Experiences with the Chinese impulse generator MPTA 71-3 clearly show the necessity to determine the performance of the generator and to measure and record the strength, configuration and frequency of the electrical impulses employed. A simple equipment for measuring these factors is described. The apparatus makes it possible to record the character and type of the stimuli and to compare different techniques of stimulation.

Heat stroke is an acute life-threatening disease requiring therapy immediate to cope with the severe pathophysiologic disturbances. Rapid lowering of the high core temperature seems to be the most important therapeutic measure. Besides methods of physical cooling, Dantrolene should also be used in this hyperthermic state. By consequent lowering of the body temperature it will be possible to stabilise circulation and minimise disease-related injuries of different organs.