Search

The effect of boron (B) on stress corrosion resistance of S31254 in the presence of residual stresses has been studied. The microstructure and corrosion resistance of S31254 containing B at different levels of cold deformation are analyzed in this study. In the results, it is shown that B favors the improvement of deformation uniformity of S31254. The grain boundary (GB) and slip bands have better corrosion resistance at 5% deformation, and the overall corrosion resistance is better than that of the undeformed state, with smaller passivation current density and narrower width of GB corrosion grooves, especially for the 40B samples. At 30% deformation, the overall corrosion resistance of 40B S31254 is better than 0B due to improved deformation uniformity. [ABSTRACT FROM AUTHOR]

Polylactic acid (PLA) is the prevailing raw material for fused deposition modeling (FDM) 3D printing filaments, offering benefits such as a low printing temperature, minimal shrinkage, and biodegradability. However, this material has challenges such as poor toughness, low heat deflection temperature, susceptibility to moisture‐induced thermal degradation, and high costs. This study addressed these concerns by incorporating natural bamboo fiber (BF) into PLA, elevating heat the deflection temperature and lowering the material costs. Additionally, a synthesized branched structure compatibilizer, in the form of epoxidized soybean oil‐branched cardanol ether (ESOn‐ECD), enhanced the toughness of PLA, the bonding strength between PLA and the BF surface, and the flowability of high‐fiber composites during processing and printing. The mechanical, thermal, and rheological properties were assessed, demonstrating the promising processing performance of PLA/BF/ESO3‐ECD. The fully biobased composite exhibits strength, toughness, good processability, excellent 3D printability, and durability, implying substantial potential in FDM 3D filament production. Highlights: Bio‐based PLA/bamboo fiber/ESO3‐ECD FDM 3D printing filaments were developed.The excellent nucleation ability of the bamboo fibers enhances the crystallization rate and crystallinity of PLA.The epoxy values and branching degree of ESOn‐ECD are crucial for its effective modification. [ABSTRACT FROM AUTHOR]

Ni was selected as a transition layer and sublayer in the diamondlike carbon-based multilayered film with varied bilayer periods (from 228 to 970 nm) prepared by magnetron sputtering. The reaction between Ni- and C-containing particles was discussed, and the influences of bilayer periods on the structure and morphology, accompanied with the frictional behaviors at different loading forces (2 and 5 N), as well as the field emission properties were investigated. The results showed that Ni grew in the (111) plane, and there was no Ni–C bond or graphene formed in the film because of the relatively lower energy during deposition. Moreover, the content of sp2C in the film, the hardness, and the field emission performance exhibited an initial increase followed by a subsequent decrease with increasing bilayer periods. However, the frictional coefficient decreased owing to more graphitization with an increase of the applied load. Particularly noteworthy was that the film possessed a bilayer period of 710 nm, displayed a compact structure with a smaller grain size, and showed reduced sp2C content in the role of Ni. This resulted in sustained lower surface roughness, heightened hardness, decreased coefficient of friction, and a smaller opening electric field. [ABSTRACT FROM AUTHOR]

Plasticizers are widely used in poly(vinyl chloride) (PVC), polylactic acid (PLA), thermoplastic starch (TPS), and other modified powder materials to enhance the flowability, flexibility, and processability of macromolecules. Because of the reprotoxicity of phthalates in animals and humans, certain phthalates have recently been banned in the United States and Europe. Biobased plasticizers from green biomass–derived renewable resources with low toxicity are expected to be a substitute for phthalates. Among a variety of newly developed biobased monomers, cardanol, and isosorbide are the two most promising materials because of their unique structural features. This review summarizes the research progress of cardanol‐ and isosorbide‐based plasticizers with synergistic effects of plasticization, thermal stabilization, and anti‐migration. By summarizing and analyzing the relationship between molecular structure of plasticizer and plasticizing performance, this review can provide theoretical guidance for future research on the design of isosorbide‐ and cardanol‐based plasticizers. Highlights: Biobased plasticizers with low toxicity are expected to replace certain phthalates.The plasticizing effect of single biobased plasticizer is not good.Biobased plasticizer with synergistic effects is required.There exists the trade‐off effect between the molecular weight and the compatibility.Epoxidized isosorbide ester can be used as a heat stabilizer. [ABSTRACT FROM AUTHOR]