Search

The ultramafic rock located on the northern slope of Lüliang Mountain in the northwestern region of North Qaidam Orogen is altered to serpentinite. The occurrence of disseminated chromite within the serpentinite holds significant implications for understanding the petrogenesis of the protolith. This work provides strong evidence of a distinct zonal texture in the chromite found in the ultramafic rock, using petrographic microstructure and electron probe composition analysis. The core of the chromite is characterized by high contents of Cr#, with enrichment in Fe3+# (Fe3+/(Cr + Al + Fe3+)) and depletion in Al2O3 and TiO2. The Cr2O3 content ranges from 51.64% to 53.72%, while the Cr# values range from 0.80 to 0.84. The FeO content varies from 24.9% to 27.8%, while the Fe2O3 content ranges from 5.19% to 8.74%. The Al2O3 content ranges from 6.70% to 9.20%, and the TiO2 content is below the detection limit (# values ranging from 0.13 to 0.25 and Fe3+# values ranging from 0.07 to 0.12. The mineral chemistry of the chromite core in the ultramafic rock suggests it to be from an ophiolite. This ophiolite originated from the fore-arc deficit asthenosphere in a supra-subduction zone. The estimated average crystallization temperature and pressure of the chromite are 1306.02 °C and 3.41 GPa, respectively. These values suggest that the chromite formed at a depth of approximately 110 km, which is comparable to that of the asthenosphere. The chromite grains are surrounded by thick rims composed of Cr-rich magnetite characterized by enrichment in Fe3+# contents and depletions in Cr2O3, Al2O3, TiO2, and Cr#. The FeO content ranges from 28.25% to 31.15%, while the Fe2O3 content ranges from 44.94% to 68.92%. The Cr2O3 content ranges from 0.18% to 23.59%, and the Al2O3 and TiO2 contents are below the detection limit (# values ranging from 0.90 to 1.00, Mg# values ranging from 0.01 to 0.06, and Fe3+# values ranging from 0.64 to 1.00, indicating late-stage alteration processes. The LA-ICP-MS zircon U-Pb dating of the ultramafic rock yielded an age of 480.6 ± 2.4 Ma (MSWD = 0.46, n = 18), representing the crystallization age of the ultramafic rock. This evidence suggests that the host rock of chromite is an ultramafic cumulate, which is part of the ophiolite suite. It originated from the fore-arc deficit asthenosphere in a supra-subduction zone during the northward subduction of the North Qaidam Ocean in the Ordovician period. Furthermore, clear evidence of Fe-hydrothermal alteration during the post-uplift-denudation stage is observed.

In this study, the ball-on-disk sliding wear and tribocorrosion behavior in the H2SO4 and HCl solution of NiCoCrMoCu alloys with carbon additions of 0.2, 1, 1.5, and 2 wt.% with the Al2O3 ball as a counterpart was investigated systematically. Obvious tribocorrosion antagonistic effects were found after wear in both aqueous solutions. Compared with dry sliding wear conditions, the lubrication effect of the aqueous solution significantly reduces the wear rate of the alloy, and the reduction effect in the H2SO4 aqueous solution was more obvious than that in HCl. The antagonistic effects of the 0.2C and 1C alloys decrease with the load and sliding rate, while those of the 1.5C and 2C alloys increase. The (coefficient of friction) COF and wear rate under different loads and sliding rates were analyzed using the response surface analysis (RSM) method. It was found that the COF mainly showed dependence on the sliding rate, while the wear rate showed dependence on load and sliding speed.

The inconsistencies regarding the fundamental correlation between Gd content and slip (twinning) activities of Mg alloys appeal further investigations. However, the traditional slip dislocations analysis by TEM is time-consuming, and that by SEM/EBSD cannot recognize the partial slip modes. These urge a more efficient and comprehensive approach to easily distinguish all potential slip modes occurred concurrently in alloy matrix. Here we report a modified lattice rotation analysis that can distinguish all slip systems and provide statistical results for slip activities in Mg alloy matrix. Using this method, the high ductility of Mg-Gd alloy ascribed to the enhanced non-basal slips, cross-slip, and postponed twinning activities by Gd addition is quantitatively clarified.

This paper presents the background, scientific objectives, experimental design, and preliminary achievements of the Xin’anjiang nested experimental watershed (XAJ-NEW), implemented in 2017 in eastern China, which has a subtropical humid monsoon climate and a total area of 2674 km2. The scientific objectives of the XAJ-NEW include building a comprehensive, multiscale, and nested hydrometeorological monitoring and experimental program, strengthening the observation of the water cycle, discovering the spatiotemporal scaling effects of hydrological processes, and revealing the mechanisms controlling runoff generation and partitioning in a typical humid, hilly area. After two years of operation, preliminary results indicated scale-dependent variability in key hydrometeorological processes and variables such as precipitation, runoff, groundwater, and soil moisture. The effects of canopy interception and runoff partitioning between the surface and subsurface were also identified. Continuous operation of this program can further reveal the mechanisms controlling runoff generation and partitioning, discover the spatiotemporal scaling effects of hydrological processes, and understand the impacts of climate change on hydrological processes. These findings provide new insights into understanding multiscale hydrological processes and their responses to meteorological forcings, improving model parameterization schemes, and enhancing weather and climate forecast skills.

Twinning-detwinning (TDT) behavior in a strongly basal-textured Mg-Li alloy during two-step compression (RD)-compression (ND) process was investigated using quasi-in-situ EBSD. TDT behavior and TDT variants selection were statistically discussed with the loading path for the first time. Non-Schmid twinning behavior was observed in the first step compression, owing to the local stress fluctuations by neighboring twins; in contrast, Schmid's law well predicted the detwinning variants selection. This asymmetrical TDT behavior was first investigated to date related with the strong basal texture and loading path. Besides, with the progress of compression, Schmid factors for twinning demonstrated a decreasing tendency; however, those for detwinning during the second step displayed an abnormally increasing trend, fundamentally stemming from prior twinning behavior.

Water use efficiency (WUE) quantifies the trade-off between carbon gain and water loss. A deep understanding of its relationships with the controlling factors is essential for predicting ecosystem responses to climate change. Our study utilized the eddy covariance measurements to analyze the variability of WUE and its influencing climate factors at the seasonal, monthly, 8-day, daily, and half-hourly scales and during the episodic drought and wet periods at a typical subtropical evergreen forest of Southeast China. The results show that ET is the dominant factor influencing the WUE variability with a relative contribution of 57.56 ± 2.26% for different seasons in this study area. Secondly, WUE responds differently to climatic drivers from monthly to half-hourly scales. Our results show that WUE has a remarkably high sensitivity to soil moisture at multi-time scales (from monthly to half-hourly), and the connection strength increases with increasing time scale. Thirdly, there is no significant relationship between VPD and WUE as time scale expands. In addition, WUEs during the episodic drought period have higher values than those during the episodic wet period on the monthly scales. The half-hourly WUE during the episodic drought period is close to the WUE during the episodic wet period from 8:30 to 19:00 but is higher from 6:00 to 8:00. These results indicate that soil moisture plays an important role on influencing WUE variation at multi-time scales and under extreme climatic conditions.

This study is the first to research the microstructure and mechanical properties of the workpiece after additive friction stir deposition (AFSD) of the feedstock at different heat treatment stages. AA2219 aluminum alloys with three different heat treatment stages were selected as the feedstock, and alloys with dense structure were successfully prepared by the additive friction stir deposition AFSD process. Experimental results show that AFSD exhibits an excellent ability to refine grains and improve the uniform distribution of precipitates in the second phase, thereby improving the plasticity of AA2219 alloy after the AFSD process. Because of the continuous dynamic recrystallization (CDRX) in the AA2219 alloy during AFSD, the grain size after the AFSD process is independent of the initial feedstock grain size for three samples. The equilibrium phase (θ) size is genetically related to the initial size of the second-phase particles in the feedstock. Due to grain refinement and dislocation strengthening, the yield strength of AA2219-casting increased significantly from 79.8 MPa to 124.1 MPa after AFSD. The yield strength of the AA2219-T4 decreases slightly from 151.8 MPa to 140.4 MPa after AFSD. The precipitation of the second phase leads to a decrease in solid solution strengthening and dislocation strengthening. However, grain refinement strengthening partially offsets this reduction. The yield strength of AA2219-T87 decreased from 398.5 MPa to 147.2 MPa after AFSD. As such, grain refinement strengthening and solid solution strengthening by the AFSD process are much smaller than the yield strength lost by precipitation strengthening and dislocation strengthening.

In this study, Cu-10 wt% Fe alloy in as-cast state was modified using friction stir processing (FSP). The microstructure evolution of Cu-10 wt% Fe alloys in different states was characterized in detail using scanning electron microscopy (SEM), electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM). The results show that due to dynamic recrystallization, the FSPed Cu-10 wt% Fe alloy obtained a uniformly equiaxed ultrafine microstructure with low density of dislocation, high proportion of high-angle grain boundaries (HAGBs), and high degree of recrystallization. Fine equiaxed grains with an average size of 0.6 μm were produced after FSP. Many fine-precipitate Fe-phases with an average size of 20 nm were uniformly distributed in the Cu matrix. The FSPed samples possessed excellent mechanical properties, such as high Vickers hardness (163.5 HV), ultimate tensile strength (538.5 MPa), and good elongation (16%). This single-pass FSP method does not require subsequent aging treatment and provides a simple and efficient way to improve the properties of Cu-Fe alloys.

Co-based alloys are promising alternatives to replace the currently used tool steels in aluminum die-casting molds for producing sophisticated products. Although the reaction is significantly less severe compared to that of tool steels, bare Co-29Cr-6Mo (CCM) alloy is still gradually corroded under molten Al, leading to the local failure of the alloy due to the formation of intermetallic compounds between the matrix and molten Al. This study indicated that prior oxidation treatment at 750 °C on CCM alloy is beneficial in enhancing the corrosion resistance of the alloy to molten Al. The is more pronounced in the alloy after a longer oxidation treatment. However, after oxidation for longer than 24 h, the protectiveness of the film cannot be enhanced anymore. In addition, even after the full failure of the oxide film, the thickness loss rate of a sample with prior oxidation treatment is much lower than that of a bare sample. This can be attributed to the fact that network-aligned oxide particles of the cone structure boundary inhibit both the outwards movements of alloying elements and the dissolution of the intermetallic layer.

In this study, composite plates of 6061/TA1 were successfully manufactured using additive friction stir deposition (AFSD). The impact of preheating temperatures (room temperature, 100 °C, 200 °C) on the interfacial microstructure and interface mechanical properties at various deposition zones was studied. The results showed that as the preheating temperature increased or when the deposit zone shifted from the boundary to the center, the diffusion width of Al and Ti increased, accompanied by an increase in bonding shear strength. Moreover, in the boundary zone of the sample preheated at room temperature (P-RT), only mechanical bonding was observed, resulting in the lowest bonding shear strength. Conversely, the other samples exhibited a combination of mechanical and metallurgical bonding. Under the preheating temperature of 200 °C, interfacial intermetallic compounds were observed near the center zone, which exhibited the highest bonding shear strength.

Dechlorane 602 (Dec 602) has biomagnification potential. Our previous studies suggested that exposure to Dec 602 for 7 days induced colonic inflammation even after 7 days of recovery. To shed some light on the underlying mechanisms, disturbances of gut immunity and gene expression were further studied. Adult C57BL/6 mice were administered orally with Dec 602 for 7 days, then allowed to recover for another 7 days. Colonic type 3 innate lymphoid cells (ILC3s) in lamina propria lymphocytes (LPLs) and lymphocytes in mesenteric lymph nodes (MLNs) were examined by flow cytometry. Expressions of genes in the gut were determined by RNA-Seq. It was found that Dec 602 exposure up-regulated the percentage of CD4+ T cells in MLNs. The mean fluorescent intensity (MFI) of interleukin (IL)− 22 in LPLs was decreased, while the MFI of IL-17a as well as the percentage of IL-17a+ ILC3s in LPLs were increased after exposure to Dec 602. Genes involved in the formation of blood vessels and epithelial-mesenchymal transition were up-regulated by Dec 602. Ingenuity pathway analysis of differentially expressed genes predicted that exposure to Dec 602 resulted in the activation of liver X receptor/retinoid X receptor (LXR/RXR) and suppression of muscle contractility. Our results, on one hand, verified that the toxic effects of Dec 602 on gut immunity could last for at least 14 days, and on the other hand, these results predicted other adverse effects of Dec 602, such as muscle dysfunction. Overall, our studies provided insights for the further investigation of Dec 602 and other emerging environmental pollutants.

Abstract Background Glioblastoma (GBM) is characterized by progressive growth and metastasis. Numerous studies claim that the deregulation of circular RNAs (circRNAs) is associated with cancer progression. However, the role of circRNAs in GBM is largely limited. The purpose of this study was to investigate the functions of circCDC45 in GBM and provide a feasible functional mechanism to support its role. Methods The expression of circCDC45, miR-485-5p and colony-stimulating factor 1 (CSF-1) mRNA was examined using quantitative real-time polymerase chain reaction (qRT-PCR). Cell proliferation was assessed using cell counting kit − 8 (CCK-8) assay and colony formation assay. Cell migration and cell invasion were monitored using transwell assay. The protein levels of proliferation-related markers and CSF-1 were determined using western blot. The target relationship was predicted using bioinformatics tools and validated using dual-luciferase reporter assay and RNA immunoprecipitation (RIP) assay. Animal models were constructed to verify the role of circCDC45 in vivo. Results The expression of circCDC45 and CSF-1 was elevated in GBM tissues and cells, while the expression of miR-485-5p was declined. Downregulation of circCDC45 or CSF-1 blocked GBM cell proliferation, invasion and migration as well as tumor growth in vivo. In mechanism, circCDC45 positively regulated the expression of CSF-1 by targeting miR-485-5p. Inhibition of miR-485-5p reversed the biological effects caused by circCDC45 downregulation in GBM cells. Conclusion CircCDC45 promoted the progression of GBM by mediating the miR-485-5p/CSF-1 axis, and circCDC45 might be a promising plasmatic biomarker for GBM diagnosis and treatment.

Tumor cell migration is affected by the aryl hydrocarbon receptor (AhR). However, the systematic molecular mechanisms underlying AhR-mediated migration of human neuroblastoma cells are not fully understood. To address this issue, we performed an integrative analysis of mRNA and microRNA (miR) expression profiles in human neuroblastoma SK-N-SH cells treated with 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD), a potent agonist of AhR. The cell migration was increased in a time- and concentration- dependent manner, and was blocked by AhR antagonist (CH223191). A total of 4,377 genes were differentially expressed after 24-hour-treatment with 10-10 M TCDD, of which the upregulated genes were significantly enriched in cell migration-related biological pathways. Thirty-four upregulated genes, of which 25 were targeted by 78 differentially expressed miRs, in the axon guidance pathway were experimentally confirmed, and the putative dioxin-responsive elements were present in the promoter regions of most genes (79 %) and miRs (82 %) in this pathway. Furthermore, two promigratory genes (CFL2 and NRP1) induced by TCDD was reversed by blockade of AhR. In conclusion, AhR-mediated mRNA-miR networks in the axon guidance pathway may represent a potential molecular mechanism of dioxin-induced directional migration of human neuroblastoma cells.

To study the effects of Fe content and cold drawing strain on the microstructure and properties, Cu-Fe alloys were prepared via powder metallurgy and hot extrusion. Scanning electron microscopy was applied to observe the Fe phase, and the ultimate tensile strength was investigated using a universal material testing machine. Alloying with an Fe content below 10 wt.% formed a spherically dispersed Fe phase via the conventional nucleation and growth mechanism, whereas a higher Fe content formed a water-droplet-like Fe phase via the spinodal decomposition mechanism in the as-extruded Cu-Fe alloy. Further cold drawing induced the fiber structure of the Fe phase (fiber strengthening), which could not be destroyed by subsequent annealing. As the Fe content increased, the strength increased but the electrical conductivity decreased; as the cold drawing strain increased, both the strength and the electrical conductivity roughly increased, but the elongation roughly decreased. After thermal–mechanical processing, the electrical conductivity and strength of the Cu-40Fe alloy could reach 51% IACS and 1.14 GPa, respectively. This study can provide insight into the design of high-performance Cu-Fe alloys by tailoring the size and morphology of the Fe phase.

Abstract Background Preparedness efforts for a COVID-19 outbreak required redesign and implementation of a perioperative workflow for the management of obstetric patients. In this report we describe factors which influenced rapid cycle implementation of a novel comprehensive checklist for the perioperative care of the COVID-19 parturient. Methods Within our labour and delivery unit, implementation of a novel checklist for the COVID-19 parturient requiring perioperative care was accomplished through rapid cycling, debriefing and on-site walkthroughs. Post-implementation, consistent use of the checklist was reported for all obstetric COVID-19 perioperative cases (100% workflow checklist utilization). Retrospective analysis of the factors influencing implementation was performed using a group deliberation approach, mapped against the Consolidated Framework for Implementation Research (CFIR). Results Analysis of factors influencing implementation using CFIR revealed domains of process implementation and innovation characteristics as overwhelming facilitators for success. Constructs within the outer setting, inner setting, and characteristic of individuals (external pressures, baseline culture, and personal attributes) were perceived to act as early barriers. Constructs such as communication culture and learning climate, shifted in influence over time. Conclusion We describe the influential factors of implementing a novel comprehensive obstetric workflow for care of the COVID-19 perioperative parturient during the first surge of the pandemic using the CFIR framework. Early workflow adoption was facilitated primarily by two domains, namely thoughtful innovation design and careful implementation planning in the setting of a long-standing culture of improvement. Factors initially assessed as barriers such as communication, culture and learning climate, transitioned into facilitators once a perceived benefit was experienced by healthcare teams. These results provide important information for the implementation of rapid change during a time of crisis.

Background: Chlorinated flame retardant Dechlorane 602 (Dec 602) has been detected in daily food, indicating that it may pose a risk to intestinal health. The intestinal microenvironment plays an important role in intestinal health. Intestinal microbiota and metabolites are two important factors for maintaining the microenvironment. However, little is known about the effects of Dec 602 on intestinal microbiota and metabolites. Objectives: We aimed to probe the effects of Dec 602 on the intestine by revealing the changes that Dec 602 caused to the intestinal microbiota and metabolites. Methods: Adult female C57BL/6 mice were exposed to Dec 602 (low/high doses: 1.0/10.0 μg/kg body weight per day) orally for 7 consecutive days, and sacrificed after 7 days of recovery. The composition of colonic microbiota was measured by 16S rRNA gene sequencing, and the colonic metabolites were determined by LC-ESI-MS/MS. Finally, the effects of Dec 602 on the colon were validated by histopathological analysis. Results: The intestinal microbiota composition was altered toward a pro-inflammatory status after exposure to Dec 602. Dec 602 exposure also up-regulated oxidative metabolites (glutathione disulfide, taurine and retinoic acid) and pro-inflammatory metabolites (prostaglandin E2). On the other hand, antioxidative metabolites (s-adenosylmethionine and 11-cis-retinol) and anti-inflammatory metabolites (alpha-linolenic acid, eicosapentaenoic acid and docosahexaenoic acid) were down-regulated after exposure to Dec 602. Infiltration of lymphocytes in the colonic lamina propria was observed in the mice treated with Dec 602 for 7 days, and it was not recovered after another 7 days without further treatment. Conclusion: Dec 602 interfered with the colonic microbiota and metabolome, and exhibited inflammatory features. Histopathological studies confirmed that Dec 602 exposure did induce colonic inflammation.

The Integrated Multisatellite Retrievals for GPM (IMERG) is designed to derive precipitation by merging data from all the passive microwave (PMW) and infrared (IR) sensors. While the input source errors originating from the PMW and IR sensors are important, their structure, characteristics, and algorithm improvement remain unclear. Our study utilized a four-component error decomposition (4CED) method and a systematic and random error decomposition method to evaluate the detectability of IMERG dataset and identify the precipitation errors based on the multi-sensors. The 30 min data from 30 precipitation stations in the Tunxi Watershed were used to evaluate the IMERG data from 2018 to 2020. The input source includes five types of PMW sensors and IR instruments. The results show that the sample ratio for IR (Morph, IR + Morph, and IR only) is much higher than that for PMW (AMSR2, SSMIS, GMI, MHS, and ATMS), with a ratio of 72.8% for IR sources and a ratio of 27.2% for PMW sources. The high false ratio of the IR sensor leads to poor detectability performance of the false alarm ratio (FAR, 0.5854), critical success index (CSI, 0.3014), and Brier score (BS, 0.1126). As for the 4CED, Morph and Morph + IR have a large magnitude of high total bias (TB), hit overestimate bias (HOB), hit underestimate bias (HUB), false bias (FB), and miss bias (MB), which is related to the prediction ability and sample size. In addition, systematic error is the prominent component for AMSR2, SSMIS, GMI, and Morph + IR, indicating some inherent error (retrieval algorithm) that needs to be removed. These findings can support improving the retrieval algorithm and reducing errors in the IMERG dataset.

Glioblastoma is the most frequent, as well as aggressive kind of high-grade malignant glioma. Chemoresistance is posing a significant clinical barrier to the efficacy of temozolomide-based glioblastoma treatment. By suppressing xeroderma pigmentosum group A (XPA), a pivotal DNA damage recognition protein implicated in nucleotide excision repair (NER), we devised a novel method to enhance glioblastoma therapy and alleviate temozolomide resistance. On the basis of preliminary assessment, we found that XPA dramatically increased in glioblastoma compared with normal cells and contributed to temozolomide resistance. By constructing XPA stably knockdown cells, we illustrate that XPA protects glioma cells from temozolomide-triggered reproductive cell death, apoptosis, as well as DNA repair. Besides, XPA silencing remarkably enhances temozolomide efficacy in vivo . This study revealed a crucial function of XPA-dependent NER in the resistance of glioma cells to temozolomide.

Screening for early-stage lung cancer with low-dose computed tomography is recommended for high-risk populations; consequently, the incidence of pure ground-glass opacity (pGGO) is increasing. Ground-glass opacity (GGO) is considered the appearance of early lung cancer, and there remains an unmet clinical need to understand the pathology of small GGO (

Introduction: Parasitic infections of the eye are a major cause of ocular-surface diseases globally. While most infections are treatable, parasites can cause varying levels of damage mostly due to late diagnosis or misdiagnosis as a result of doctors’ unfamiliarity with their characteristics of latency and crypsis, as well as lack of awareness by the patients. Case Reports: In this study, we present three cases of phthiriasis palpebrarum, thelaziasis, and ophthalmomyiasis, respectively. Two of the cases were treated at the clinic and did not recur. One patient refused treatment and was lost to follow-up. Discussion: By evaluating the natural histories, morphology, symptoms, clinical findings, and treatment of these parasitic diseases, we systematically analyzed several distinct and unique parasite characteristics, especially latency and crypsis. Furthermore, we have proposed specific examination techniques and methods as well as prevention and treatment strategies from these specific perspectives, aiming to prompt timely diagnoses and early interventions for these diseases by health care workers and improve the public’s awareness of parasitic infections. Conclusion: Parasitosis on the ocular surface is a global infectious disease, and prevention strategies include maintaining personal and environmental hygiene and limiting contact with animals. We recommend that health care workers should enhance their ability to detect and diagnose these diseases while promoting the public’s awareness of them in the context of our new perspectives.

A Cu-10 Ni-2Ti wt.% alloy has been fabricated by induction melting and casting. The microstructure evolutions of the studied alloy treated with thermal-mechanical treatment were characterized. After homogenized at 950 °C for four hours, hot rolling by 80% at 900 °C solid solution treated at 970 °C for four hours, cold-rolled by 50%, aged at 450 °C for one hour, the hardness, electrical conductivity, tensile strength, yield strength, and the elongation of the studied alloy approached 181 HV, 22.1% IACS, 576 MPa, 486 MPa, and 14.6%, respectively. The studied alloy shows large products of strength and elongation (15.4 GPa·%, 9.3 GPa·%, 8.41 GPa·%, and 10.1 GPa·% for the samples treated with a solid solution, under aged, peak aged, and over-aged states), which are much higher than those of other high strength conductive copper alloys. These findings are helpful in designing new high damage tolerance conductive materials. Keywords: Cu alloy, Damage tolerance, Precipitation, Strength, Microstructure

ABSTRACT Purpose: Subarachnoid hemorrhage (SAH) is a common complication of cerebral vascular disease. Hydrogen has been reported to alleviate early brain injury (EBI) through oxidative stress injury, reactive oxygen species (ROS), and autophagy. Autophagy is a programmed cell death mechanism that plays a vital role in neuronal cell death after SAH. However, the precise role of autophagy in hydrogen-mediated neuroprotection following SAH has not been confirmed. Methods: In the present study, the objective was to investigate the neuroprotective effects and potential molecular mechanisms of hydrogen-rich saline in SAH-induced EBI by regulating neural autophagy in the C57BL/6 mice model. Mortality, neurological score, brain water content, ROS, malondialdehyde (MDA), and neuronal death were evaluated. Results: The results show that hydrogen-rich saline treatment markedly increased the survival rate and neurological score, increased neuron survival, downregulated the autophagy protein expression of Beclin-1 and LC3, and endoplasmic reticulum (ER) stress. That indicates that hydrogen-rich saline-mediated inhibition of autophagy and ER stress ameliorate neuronal death after SAH. The neuroprotective capacity of hydrogen-rich saline is partly dependent on the ROS/Nrf2/heme oxygenase-1 (HO-1) signaling pathway. Conclusions: The results of this study demonstrate that hydrogen-rich saline improves neurological outcomes in mice and reduces neuronal death by protecting against neural autophagy and ER stress.

Cancer occurrence and development are closely related to the environment. Aryl hydrocarbon receptor (AhR) is an important receptor mediating the toxic effects of many environmental compounds, and is also involved in regulating tumor cell migration. Glioblastoma is the most malignant glioma and exhibits high motility, but the effects of AhR on the migration of glioblastoma are still unclear. We aimed to understand the role of AhR in the migration of this type of tumor cell and to explore the underlying molecular mechanism. In cultured human neuroblastoma cells (U87), we found that AhR overexpression or knockdown increased or suppressed the migration ability of U87 cells, respectively. Furthermore, inhibition of basal activation of the AhR pathway suppressed migration ability, suggesting a positive correlation between endogenous activity of the AhR pathway and cell migration. When the AhR pathway was activated by 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD) or 6-formyl [3,2-b] carbazole (FICZ), the migration of U87 cells was inhibited by inducing the expression of a tumor suppressor, IL24, which is a downstream responsive gene of AhR activation. Moreover, a similar AhR-IL24-dependent mechanism for migration inhibition of TCDD was documented in a breast cancer cell line and a lung cancer cell line. This study demonstrated that AhR plays important roles in regulating the migration of glioblastoma, and the induction of the AhR-IL24 axis mediates the inhibition of migration in response to TCDD or FICZ treatment.

The porous aerostatic bearing is a new supporting structure that is widely used in precision and ultraprecision engineering and the aerospace and other fields. The aerostatic bearing has a good bearing capacity and static stiffness. In this work, the numerical and experimental research on the static characteristics of an aerostatic bearing based on a porous SiC ceramic membrane is presented. The porous ceramic membrane prepared by reactive sintering, with a porosity of 25.8% and a pore size of 20.55 μm, was used as the restrictor to fabricate the aerostatic bearing. It was found that the ceramics have good permeability, and the permeability coefficient reached 2.78 × 10−13 m2 using permeability-test experiments. The effects of the gas-supply pressure and permeability coefficient on the static characteristics of the aerostatic bearing based on porous ceramics were analyzed using Fluent simulation calculation. When the gas-supply pressure was 0.5 MPa and the gas-film thickness was 6 μm, the static stiffness of the aerostatic bearing reached a maximum of 20.9 N/μm, while the bearing capacity was 632.5 N. The numerical results of the static characteristics of the aerostatic bearing are highly consistent with the experimental results, which verifies the accuracy of the Fluent simulation, and provides convenience for studying the static characteristics of aerostatic bearings.

This work was mainly focused on the processing-parameter-related microstructure and properties of ultrafine WC-10Co-0.4VC-0.5Cr3C2 cemented carbide. The samples were prepared via a spark plasma sintering (SPS) technique using nano WC and Co powders and the corresponding inhibitor VC and Cr3C2 powders. The influence of the processing process on the microstructure and mechanical properties of ultrafine-grained cemented carbide was investigated under different ball-milling times and sintering temperatures. The results showed that the grain size of WC decreased with increasing ball-milling time and decreasing sintering temperature and that the specific gravity of ε-Co increased with increasing ball-milling time. The hardness of cemented carbide increased with increasing ball-milling time and decreased with increasing sintering temperature due to the corresponding variation in grain size and the relative density of samples. The transverse fracture strength (TRS) was mainly affected by ball-milling time. The increase in ball-milling time led to decreased TRS values, mainly ascribed to the formation of WC particle agglomeration and the decreased WC-Co eutectic temperature. In addition, temperature changes were found to have little effect on TRS. The samples sintered at 1250 °C with a ball-milling time of 60 h had comprehensive mechanical properties. Their average grain size, relative density, hardness, and TRS were 355.5 nm, 95.79%, 2035.5 kg/mm2, and 2155.99 MPa, respectively.

In this work, the quantification of key microstructural features like γ′ size morphology distribution, grain size, and localized stress distribution, especially near a fracture, were coupled with mechanical properties under various temperatures in Ni-base powder metallurgy superalloys subjected to sub-solvus or super-solvus heat treatments. Compared to super-solvus heat-treated alloy, sub-solvus heat-treated superalloy with a finer grain size exhibited higher ductility/strength at 550 °C, whilst adverse trend was observed at higher temperatures (750 and 830 °C). Besides, for both alloys, the strength and ductility decreased with the decrease in strain rate, resulting from oxidation behavior. Larger grain size or less grain boundary density can facilitate the retardation of oxidation behavior and weaken the propensity of early failure at higher temperatures.

Additive manufacturing is an advanced forming method to fabricate complex components, while cracks appear in the deposited nickel-based single crystal superalloy samples undesirably. Though fabrication of crack-free superalloy were reported, effective solutions to fabricate crack-free nickel-based single crystal superalloy samples are still uncovered, thus the additive manufacturing in single crystal superalloy is still an extremely difficult work. In this work, we fabricated nickel-based single crystal superalloy samples through laser powder deposition, and analyzed the causes of crack during deposition processing. Experimental results demonstrate that the as-deposited thin-wall samples presented single crystal structure and its crystal orientation is well aligned with the [001] orientation of substrate, while some cracks appeared in the as-deposited block samples. Large misorientation angle in the local regions played significant roles in the cracks initiation and the further cracking propagation. Solidification cracks are attributed to the shrinkage cavities and the high-melting point interdendritic carbides, while liquation cracks are attributed to the low melting point compounds. These findings give a guide for causes analysis on cracks in the nickel-based single crystal superalloy fabricated by laser powder deposition additive manufacturing, which has bright prospects in single crystal superalloy manufacturing and repair. Keywords: Superalloy, Single crystal, Crack, Laser powder deposition, Additive manufacturing

As an advanced material forming method, additive manufacturing (AM) has been rapidly developed in many industry fields. Due to the non-weldability of nickel-based single crystal (SX) superalloys and complex solidification and stress conditions of AM process, hot cracks can easily form in depositions. Previous research focused on the additive manufacturing of single-track thin-walled SX samples, while effective solutions to fabricate crack-free multi-track SX block samples are still limited. Directed energy deposition (DED) technique was used to fabricate multi-track block samples in this work. The effects of the overlapping ratio, scanning velocity, and laser power on the microstructure and cracking susceptibility were analyzed. The experimental results demonstrated that improper process parameters play significant roles in the formation of high-angle grain boundaries and large internal stress, both of which will increase the cracking susceptibility. Crack-free SX multi-track block was successfully fabricated after adjusting the process parameters. These findings provide a guide to reduce the cracking susceptibility by controlling the process parameters, which aids in fabrication of large-scale crack-free SX blocks through DED technique.

The Portevin-Le Châtelier (PLC) effect in a powder metallurgy (PM) Co-Ni-based superalloy was systematically investigated via the tensile tests at temperatures ranging from 200 to 600 °C and strain rates at 1.0 × 10−4 to 1.0 × 10−2. Both normal and inverse PLC effects were observed in the PLC regime, and the former appeared in the A and B types at a low temperature, whilst the latter appeared in the C type at an elevated temperature. Both positive and negative strain rate sensitivities (SRS) were shown in PLC regime, and SRS should be derived from same types of serrations. Based on the calculated activation energy, the substitutional atom Mo is considered to take primary responsibility for the PLC effect in present alloy.

Air bearing has been widely applied in ultra-precision machine tools, aerospace and other fields. The restrictor of the porous material is the key component in air bearings, but its performance is limited by the machining accuracy. A combination of optimization design and material modification of the porous alumina ceramic membrane is proposed to improve performance within an air bearing. Porous alumina ceramics were prepared by adding a pore-forming agent and performing solid-phase sintering at 1600 °C for 3 h, using 95-Al2O3 as raw material and polystyrene microspheres with different particle sizes as the pore-forming agent. With 20 wt.% of PS50, the optimum porous alumina ceramic membranes achieved a density of 3.2 g/cm3, a porosity of 11.8% and a bending strength of 150.4 MPa. Then, the sintered samples were processed into restrictors with a diameter of 40 mm and a thickness of 5 mm. After the restrictors were bonded to aluminum shells for the air bearing, both experimental and simulation work was carried out to verify the designed air bearing. Simulation results showed that the load capacity increased from 94 N to 523 N when the porosity increased from 5% to 25% at a fixed gas supply pressure of 0.5 MPa and a fixed gas film thickness of 25 μm. When the gas film thickness and porosity were fixed at 100 μm and 11.8%, respectively, the load capacity increased from 8.6 N to 40.8 N with the gas supply pressure having been increased from 0.1 MPa to 0.5 MPa. Both experimental and simulation results successfully demonstrated the stability and effectiveness of the proposed method. The porosity is an important factor for improving the performance of an air bearing, and it can be optimized to enhance the bearing’s stability and load capacity.

In this study, the distribution, proportion and characteristics of internal defects in three kinds of powders of Ti-6Al-4V, 316-steel and Co-29Cr-6Mo alloys, produced by the plasma rotating electrode process (PREP) at various rotation speeds, are characterized by using both scanning electron microscopy (SEM) and synchrotron X-ray computed tomography (CT). The results show that in the powder of a given alloy, internal pores are formed more easily in coarse particles than in fine powder during PREP. The proportion of powder with pores can be reduced by appropriately increasing the rotation speed. In addition, the composition of an alloy has a great influence on the defect formation.

Microstructure and mechanical properties of novel Ni-20Co-12Cr superalloys, with and without Nb addition, were systematically studied during long-term thermal exposure. With increased exposure time, the average diameter of the γ′ precipitates increased in both alloys in succession; this is more obviously observed in alloy containing 1 wt% Nb (1Nb). It is suggested that Nb increased the γ′ coarsening rate by accelerating the diffusion of Al and Nb in γ matrix. In addition, the γ′ phase fraction is increased by about 4% in 1Nb compared to the alloy without Nb (0Nb). The morphology of the γ′ phase changed from near-spherical to cuboidal shape during exposure in both alloys. Due to the increased γ/γ′ lattice misfit by Nb addition, 1Nb alloy showed an earlier tendency of shape change. Vickers hardness results revealed that the overall hardness decreased with the exposure time because the size increment of the γ′ precipitate weakened the precipitates strengthening and Orowan strengthening.

Owing to its high specific strength and low density, Al–Cu alloys have been extensively used in aerospace for lightweight components. Additive manufacturing techniques such as selective laser melting, which offers geometric freedom, is suitable for topology-optimized designs. In this study, the effect of processing parameters on the densification, microstructure, and mechanical properties of additively manufactured Al–Cu alloy 2124 by selective laser melting was investigated. Parameters such as laser power, scanning speed, hatch spacing, and use of a support were studied. The results revealed that a grille support with a hollow structure played a resistant role in the transfer of heat to the base plate, thus reducing the temperature gradient and lessening cracks in the building part. Smaller hatch spacing was beneficial for the achievement of a higher relative density and strength due to track re-melting and liquid phase backflow, which could fill cracks and pores during the building process. An ultimate tensile strength as high as 300 MPa of the vertically built sample was obtained at optimized processing parameters, while the elongation was relatively limited. Moreover, columnar grains were found to be responsible for the anisotropy of the mechanical properties of the as-printed 2124 alloy.

Microstructure and corrosion behavior of the Mg-3Al-xMn (x = 0, 0.12, 0.21, 0.36, 0.45) (hereafter in wt.%) alloys were experimentally investigated by electron probe microanalysis (EPMA), scanning electron microscope equipped with energy dispersive X-ray spectroscopy (SEM/EDX), X-ray diffraction (XRD), electrochemical, and hydrogen evolution tests. A new self-constructed Mg-Al-Mn-Fe thermodynamic database was used to predict the solidification paths of the alloys. The addition of Mn showed no grain refinement in the cast Mg-3Al alloys. According to the microstructure observation, Al-Fe phases were observed in the non-Mn-added alloy, while Al8Mn5(LT) (Al8Mn5 in low temperature) became the main intermetallic phase in the Mn-added alloys, and the amount increased gradually with the Mn addition. The τ–Al0.89Mn1.11 phase with lower Al/(Fe + Mn) ratio was observed in the alloys with 0.36 and 0.45 wt.% Mn content. According to the electrochemical tests, all five alloys showed localized corrosion characteristics in 3.5 wt.% NaCl solution. Compared with the Mg-3Al alloy, the corrosion resistance of Mn-added alloys were significantly improved and increased gradually with the Mn addition, which was due to the variation of Al-containing intermetallic compounds. The present experimental investigations and thermodynamic calculations confirmed the mechanism that the increasing amount of Al8Mn5(LT) with Mn addition could encapsulate the B2-Al(Mn,Fe) phase with higher Fe. Therefore, it could prevent this detrimental phase from contacting magnesium matrix, thus suppressing micro-galvanic corrosion and improving corrosion resistance gradually.

This research was aimed at investigating the high temperature oxidation behavior of Inconel 718 superalloy fabricated by electron beam melting with the building direction of 0°, 55° and 90° deviation from the Z axis of cylindrical samples. Columnar γ-fcc phase with preferred crystal orientations was found in all specimens. With the temperature ranging from 700 to 1000 °C, the 0° sample, symbolized by the lowest grain boundary density, and largest grain size, reveals the best oxidation performance. It is concluded that the building direction has more impact on the amount of grain boundary density than crystal orientation, which determined the oxidation resistance.

The microstructure with homogeneously distributed grains and less prior particle boundary (PPB) precipitates is always desired for powder metallurgy superalloys after hot isostatic pressing (HIPping). In this work, we studied the effects of HIPping parameters, temperature and pressure on the grain structure in PM superalloy FGH96, by means of scanning electron microscope (SEM), electron backscatter diffraction (EBSD), transmission electron microscope (TEM) and Time-of-flight secondary ion spectrometry (ToF-SIMS). It was found that temperature and pressure played different roles in controlling PPB precipitation and grain structure during HIPping, the tendency of grain coarsening under high temperature could be inhibited by increasing HIPping pressure which facilitates the recrystallization. In general, relatively high temperature and pressure of HIPping were preferred to obtain an as-HIPped superalloy FGH96 with diminished PPB precipitation and homogeneously refined grains.

An incomplete understanding of the molecular mechanisms responsible for myometrial activation from the quiescent pregnant state to the active contractile state during labor has hindered the development of effective therapies for preterm labor. Myometrial stretch has been implicated clinically in the initiation of labor and the etiology of preterm labor, but the molecular mechanisms involved in the human have not been determined. We investigated the mechanisms by which gestation-dependent stretch contributes to myometrial activation, by using human uterine samples from gynecologic hysterectomies and Cesarean sections. Here we demonstrate that the Ca requirement for activation of the contractile filaments in human myometrium increases with caldesmon protein content during gestation and that an increase in caldesmon phosphorylation can reverse this inhibitory effect during labor. By using phosphotyrosine screening and mass spectrometry of stretched human myometrial samples, we identify 3 stretch-activated focal adhesion proteins, FAK, p130Cas, and alpha actinin. FAK-Y397, which signals integrin engagement, is constitutively phosphorylated in term human myometrium whereas FAK-Y925, which signals downstream ERK activation, is phosphorylated during stretch. We have recently identified smooth muscle Archvillin (SmAV) as an ERK regulator. A newly produced SmAV-specific antibody demonstrates gestation-specific increases in SmAV protein levels and stretch-specific increases in SmAV association with focal adhesion proteins. Thus, whereas increases in caldesmon levels suppress human myometrium contractility during pregnancy, stretch-dependent focal adhesion signaling, facilitated by the ERK activator SmAV, can contribute to myometrial activation. These results suggest that focal adhesion proteins may present new targets for drug discovery programs aimed at regulation of uterine contractility.

Summary: Triacylglyceride (TAG) synthesis in the small intestine determines the absorption of dietary fat, but the underlying mechanisms remain to be further studied. Here, we report that the RNA-binding protein HuR (ELAVL1) promotes TAG synthesis in the small intestine. HuR associates with the 3′ UTR of Dgat2 mRNA and intron 1 of Mgat2 pre-mRNA. Association of HuR with Dgat2 3′ UTR stabilizes Dgat2 mRNA, while association of HuR with intron 1 of Mgat2 pre-mRNA promotes the processing of Mgat2 pre-mRNA. Intestinal epithelium-specific HuR knockout reduces the expression of DGAT2 and MGAT2, thereby reducing the dietary fat absorption through TAG synthesis and mitigating high-fat-diet (HFD)-induced non-alcoholic fatty liver disease (NAFLD) and obesity. Our findings highlight a critical role of HuR in promoting dietary fat absorption.