Search

The thermal properties of the surface and subsurface layers of planets and planetary objects yield important information that allows us to better understand the thermal evolution of the body itself and its interactions with the environment. Various planetary bodies of our Solar System are covered by so-called regolith, a granular and porous material. On such planetary bodies the dominant heat transfer mechanism is heat conduction via IR radiation and contact points between particles. In this case the energy balance is mainly controlled by the effective thermal conductivity of the top surface layers, that can be directly measured by thermal conductivity probes. A traditionally used method for measuring the thermal conductivity of solid materials is the needle-probe method. Such probes consist of thin steel needles with an embedded heating wire and temperature sensors. For the evaluation of the thermal conductivity of a specific material the temperature change with time is determined by heating a resistance wire with a well-defined electrical current flowing through it and simultaneously measuring the temperature increase inside the probe over a certain time. For thin needle probes with a large length-to-diameter ratio it is mathematically easy to derive the thermal conductivity, while this is not so straightforward for more rugged probes with a larger diameter and thus a smaller length-to-diameter ratio. Due to the geometry of the standard thin needle probes they are mechanically weak and subject to bending when driven into a soil. Therefore, using them for planetary missions can be problematic. In this paper the thermal conductivity values determined by measurements with two non-ideal, ruggedized thermal conductivity sensors, which only differ in length, are compared to each other. Since the theory describing the temperature response of non-ideal sensors is highly complicated, those sensors were calibrated with an ideal reference sensor in various solid and granular materials. The calibration procedure and the results are described in this work.

We present the high-frequency properties of the eight electric field sensors as proposed to be launched on the spacecraft "RESONANCE" in the near future. Due to the close proximity of the conducting spacecraft body, the sensors (antennas) have complex receiving features and need to be well understood for an optimal mission and spacecraft design. An optimal configuration and precise understanding of the sensor and antenna characteristics is also vital for the proper performance of spaceborne scientific instrumentation and the corresponding data analysis. The provided results are particularly interesting with regard to the planned mutual impedance experiment for measuring plasma parameters. Our computational results describe the extreme dependency of the sensor system with regard to wave incident direction and frequency, and provides the full description of the sensor system as a multi-port scatterer. In particular, goniopolarimetry techniques like polarization analysis and direction finding depend crucially on the presented antenna characteristics.

International audience; We present a study of plasma conditions in the atmospheres of the Hot Jupiters HD 209458b and HD 189733b and for an HD 209458b like planet at orbit locations between 0.2 and 1 au around a Sun-like star. We discuss how these conditions influence the radio emission we expect from their magnetospheres. We find that the environmental conditions are such that the cyclotron maser instability (CMI), the process responsible for the generation of radio waves at magnetic planets in the Solar system, most likely will not operate at Hot Jupiters. Hydrodynamically expanding atmospheres possess extended ionospheres whose plasma densities within the magnetosphere are so large that the plasma frequency is much higher than the cyclotron frequency, which contradicts the condition for the production of radio emission and prevents the escape of radio waves from close-in exoplanets at distances

The thermo-mechanical properties of planetary surface and subsurface layers control to a high extent in which way a body interacts with its environment, in particular how it responds to solar irradiation and how it interacts with a potentially existing atmosphere. Furthermore, if the natural temperature profile over a certain depth can be measured in situ, this gives important information about the heat flux from the interior and thus about the thermal evolution of the body. Therefore, in most of the recent and planned planetary lander missions experiment packages for determining thermo-mechanical properties are part of the payload. Examples are the experiment MUPUS on Rosetta's comet lander Philae, the TECP instrument aboard NASA's Mars polar lander Phoenix, and the mole-type instrument HP3 currently developed for use on upcoming lunar and Mars missions. In this review we describe several methods applied for measuring thermal conductivity and heat flux and discuss the particular difficulties faced when these properties have to be measured in a low pressure and low temperature environment. We point out the abilities and disadvantages of the different instruments and outline the evaluation procedures necessary to extract reliable thermal conductivity and heat flux data from in situ measurements., Highlights ► Numerical simulation of the thermal history of a planetary body. ► Development of robust thermal conductivity sensors for planetary applications. ► Measurement of the global heat flow of a planet or small planetary body.

International audience; On October 25th, 2006, NASA's two STEREO spacecraft were launched which are designed to increase our knowledge of the physics of the solar system. On board they carry a sophisticated radio experiment, called S/WAVES. The key technology, used by S/WAVES is the direction finding capability in addition to the use of two spacecraft which makes it possible to triangulate radio sources. Direction finding requires the reception properties of the antennas to be known very accurately. We applied several different methods to calibrate the S/WAVES antennas. In this paper the methods are described and compared and the results are presented and discussed with respect to advantages and disadvantages of the different methods.

International audience; During 2004 the Cassini/RPWS (Radio and Plasma Wave Science) instrument recorded about 5400 SEDs (Saturn Electrostatic Discharges), which were organized in 4 storm systems and 95 episodes. A computer algorithm with different intensity thresholds was applied to extract the SEDs from the RPWS data, and a statistical analysis on the main characteristics of these SEDs is performed. Compared to the SEDs recorded by the Voyagers in the early 1980s, some characteristics like SED rate, intensity, signal duration, or power spectrum are similar, but there are also remarkable differences with regard to time occurrence and frequency range: The first appearance of SEDs (storm 0) was recorded by RPWS from a distance of more than 300 Saturn radii at the end of May 2004, followed by storm A in mid-July, storm B at the beginning of August, and the most prominent storm C throughout most of September. There were also significant intervals of time with no detectable SED activity, e.g., SEDs were practically absent from October 2004 until June 2005. No clear indication for SEDs below a frequency of 1.3 MHz could be found. We suggest that the SED storms A, B, C, and possibly also storm 0 originate from the same storm system residing at a latitude of 35° South, which lasted for several months, waxed and waned in strength, and rotated with the Voyager radio period of Saturn. The SED source might be located in the updrafting water clouds beneath the visible cloud features detected in the Cassini images.

The Cassini radio and plasma wave investigation is designed to study radio emissions, plasma waves, thermal plasma, and dust in the vicinity of Saturn. Three nearly orthogonal electric field antennas are used to detect electric fields over a frequency range from 1 Hz to 16 MHz, and three orthogonal search coil magnetic antennas are used to detect magnetic fields over a frequency range from 1 Hz to 12 kHz. A Langmuir probe is used to measure the electron density and temperature. Signals from the electric and magnetic antennas are processed by five receiver systems: a high frequency receiver that covers the frequency range from 3.5 kHz to 16 MHz, a medium frequency receiver that covers the frequency range from 24 Hz to 12 kHz, a low frequency receiver that covers the frequency range from 1 Hz to 26 Hz, a five-channel waveform receiver that covers the frequency range from 1 Hz to 2.5 kHz in two bands, 1 Hz to 26 Hz and 3 Hz to 2.5 kHz, and a wideband receiver that has two frequency bands, 60 Hz to 10.5 kHz and 800 Hz to 75 kHz. In addition, a sounder transmitter can be used to stimulate plasma resonances over a frequency range from 3.6 kHz to 115.2 kHz. Fluxes of micron-sized dust particles can be counted and approximate masses of the dust particles can be determined using the same techniques as Voyager. Compared to Voyagers 1 and 2, which are the only spacecraft that have made radio and plasma wave measurements in the vicinity of Saturn, the Cassini radio and plasma wave instrument has several new capabilities. These include (1) greatly improved sensitivity and dynamic range, (2) the ability to perform direction-finding measurements of remotely generated radio emissions and wave normal measurements of plasma waves, (3) both active and passive measurements of plasma resonances in order to give precise measurements of the local electron density, and (4) Langmuir probe measurements of the local electron density and temperature. With these new capabilities, it will be possible to perform a broad range of studies of radio emissions, wave-particle interactions, thermal plasmas and dust in the vicinity of Saturn.