Search

The share of biofuels in the transportation sector is increasing. Previous studies revealed that the use of biofuels decreases the size of particles (which is linked to an increase in particulate toxicity). Current emission regulations do not consider small particles (sub-23 nm); however, there is a focus in future emissions regulations on small particles. These and the fact that within cold-start emissions are higher than during the warmed-up operation highlight the importance of a research that studies particulate matter emissions during cold-start. This research investigates the influence of biofuel on PN and PM concentration, size distribution, median diameter and cumulative share at different size ranges (including sub-23 nm and nucleation mode) during cold-start and warm-up operations using diesel and 10, 15 and 20% mixture (coconut biofuel blended with diesel). During cold-start, between 19 and 29% of total PN and less than 0.8% of total PM were related to the nucleation mode (sub-50 nm). Out of that, the share of sub-23 nm was up to 9% for PN while less than 0.02% for PM. By using biofuel, PN increased between 27 and 57% at cold-start; while, the increase was between 4 and 19% during hot-operation. The median diameter also decreased at cold-start and the nucleation mode particles (including sub-23 nm particles) significantly increased. This is an important observation because using biofuel can have a more adverse impact within cold-start period which is inevitable in most vehicles’ daily driving schedules.

As a potential means of offsetting diesel fuel usage and reducing the environmental impact of used tyres, this study investigates the NOx emissions of a modern commercial passenger vehicle run on a blend of diesel and tyre pyrolysis oil (TPO). The test vehicle was driven on a route representative of the driving expected by a courier. Vehicle drivability with the TPO/diesel blend, compared to neat diesel, was not reported to be perceived differently by the automotive industry experienced driver. Additionally, the NOx emissions were comparable between the neat diesel trip and those run on the blend of TPO/diesel. Interestingly, the results showed that short transients had a substantive impact on aggregate NOx emissions—making conclusive on-road comparisons between fuels difficult. Despite this, the data collected for this study indicate that there is no substantive NOx emissions degradation when running the TPO/diesel blend. Keywords: On-road emissions, Alternative fuels, Tyre oil, Driving dynamics

A comprehensive analysis of combustion behaviour during cold, intermediately cold, warm and hot start stages of a diesel engine are presented. Experiments were conducted at 1500 rpm and 2000 rpm, and the discretisation of engine warm up into stages was facilitated by designing a custom drive cycle. Advanced injection timing, observed during the cold start period, led to longer ignition delay, shorter combustion duration, higher peak pressure and a higher peak apparent heat release rate (AHRR). The peak pressure was ~30% and 20% and the AHRR was ~2 to 5% and ±1% higher at 1500 rpm and 2000 rpm, respectively, during cold start, compared to the intermediate cold start. A retarded injection strategy during the intermediate cold start phase led to shorter ignition delay, longer combustion duration, lower peak pressure and lower peak AHRR. At 2000 rpm, an exceptional combustion behaviour led to a ~27% reduction in the AHRR at 25% load. Longer ignition delays and shorter combustion durations at 25% load were observed during the intermediately cold, warm and hot start segments. The mass fraction burned (MFB) was calculated using a single zone combustion model to analyse combustion parameters such as crank angle (CA) at 50% MFB, AHRR@CA50 and CA duration for 10–90% MFB.

Engineering education has a key role to play in equipping engineers with the design skills that they need to contribute to national competitiveness. Product design has been described as &ldquo, the convergence point for engineering and design thinking and practices&rdquo, and courses in which students design, build, and test a product are becoming increasingly popular. A sound understanding of product development and the implications associated with developing a product have been strongly linked to sustainability outcomes. This paper presents an evaluation of a new Master level engineering unit offered at Deakin University in product development technology. The unit allowed the students an opportunity to engage with the entire product development cycle from the initial idea to prototyping and testing through strategic assessment, which drove the unit content and student learning. Within this, students were also afforded an opportunity to explore resource usage and subsequent minimisation. Student evaluation surveys over two successive years found that students were responsive to this type of learning and appreciated the opportunity to do hands-on work. Improved student effort and engagement indicate that the students likely had better learning outcomes, as compared to traditionally taught units.

This study investigates the effect of engine temperature during cold start and hot start engine operation on particulate matter emissions and engine performance parameters. In addition to a fundamental study on cold start operation and the effect of lubricating oil during combustion, this research introduces important knowledge about regulated particulate number emissions and particulate size distribution during cold start, which is an emerging area in the literature. A further aspect of this work is to introduce waste lubricating oil as a fuel. By using diesel and two blends of diesel with 1 and 5% waste lubricating oil in a 6-cylinder turbocharged engine on a cold start custom test, this investigation studied particle number (PN), friction losses and combustion instability with diesel and waste lubricating oil fuel blends. In order to understand and explain the results the following were also studied: particle size distribution and median diameter, engine oil, coolant and exhaust gas temperatures, start of injection, friction mean effective pressure (FMEP), mechanical efficiency, coefficient of variation (CoV) of engine speed, CoV of indicated mean effective pressure (IMEP) and maximum rate of pressure rise were also studied. The results showed that during cold start the increase in engine temperature was associated with an increase in PN and size of particles, and a decrease in FMEP and maximum rate of pressure rise. Compared to a warmed up engine, during cold start, PN, start of injection and mechanical efficiency were lower; while FMEP, CoV of IMEP and maximum rate of pressure rise were higher. Adding 5% waste lubricating oil to the fuel was associated with a decrease in PN (during cold start), decreased particle size, maximum rate of pressure rise and CoV of IMEP and was associated with an increase in PN and nucleation mode particles (during hot start) and FMEP.

Waste management cost for Australia is increasing every year, and thus, it is important to find alternative ways to use the waste. For example, essential oil has a significant waste stream that can be utilized in vehicles of their producers. However, some of the essential oils contain oxygen which considerably affects engine performance, emission, and combustion characteristics of diesel engines. Thus, this research paper will try to evaluate the essential oils as a replacement of diesel fuel to operate a multicylider diesel engine. For this study, two essential oils are selected which contain different oxygenated functional groups, tea tree oil (5.4% oxygen) and eucalyptus oil (8.4% oxygen), with an aim to evaluate the effect of these functional groups on engine performance and emission parameters. These oils were blended with neat diesel (0% oxygen) to obtain a blend cotaining 2.2% oxygen by weight. The blends produced similar brake power; however, brake-specific fuel consumption (BSFC) increased for eucalyptus oil blends (2.4–3.7%) and tea tree oil blends (3.9–5.3%). Essential oil–diesel blends resulted in less CO and increased NOX emission, produced similar peak pressure, and indicated mean effective pressure. The results then lead to the conclusion that oxygenated essential oils can have a role to reduce dependency of agricultural sector on diesel in the near future.

One of the most important sources of air pollution, especially in urban areas, is the exhaust emissions from passenger cars. New European emissions regulations, to minimize the gap between manufacturer-reported emissions and those emitted on the road, require new vehicles to undergo emission testing on public roads during the certification process. Outlined in the new regulation are specific boundary conditions to which the route on which the vehicle is driven must comply during a legal test. These boundary conditions, as they relate to the design and subsequent driving of a compliant route, are discussed in detail. The practicality of designing a compliant route is discussed in the context of developing a route on the Gold Coast in Queensland, Australia, in a prescriptive manner. The route itself was driven 5 times and the results compared against regulation boundary conditions.

Physico-chemical properties of microalgae biodiesel depend on the microalgae species and oil extraction method. Dioctyl phthalate (DOP) is a clear, colourless and viscous liquid as a plasticizer. It is used in the processing of polyvinyl chloride (PVC) resin and polymers. A new potential biofuel, hydrothermally liquefied microalgae bio-oil can contain nearly 11% (by mass) of DOP. This study investigated the feasibility of using up to 20% DOP blended in 80% diesel fuel (v/v) in an existing diesel engine, and assessed the performance and exhaust emissions. Despite reasonable differences in density, viscosity, surface tension, and boiling point, blends of DOP and diesel fuel were found to be entirely miscible and no separation was observed at any stage during prolonged miscibility tests. The engine test study found a slight decrease in peak cylinder pressure, brake, and indicated mean effective pressure, indicated power, brake power, and indicated and brake thermal efficiency with DOP blended fuels, where the specific fuel consumption increased. This is due to the presence of 16.4% oxygen in neat DOP, responsible for the relatively lower heating value, compared to that of diesel. The emission tests revealed a slight increase in nitrogen oxides (NOx) and carbon monoxide (CO) emissions from DOP blended fuels. However, particulate matter (PM) emissions were lower from DOP blended fuels, although some inconsistency in particle number (PN) was present among different engine loads. Refereed/Peer-reviewed