Search

Levocetirizine dihydrochloride is an effective antiallergenic drug applied mostly orally; however, developing a topical formulation for localized treatment could be beneficial. To achieve this, a modified formulation technique is necessary to enhance bioavailability efficiency and minimize possible side effects. Therefore, levocetirizine particles were prepared by immobilization on mesoporous silica material. Both the dihydrochloride form and its free base of levocetirizine were fixed on a silica-type Syloid support. Immobilization of the active ingredient levocetirizine in a free base form on a Syloid support by mixing in a dichloromethane solution provides better surface coverage (65.5%) than immobilization in the dihydrochloride form in water or methanol (24.5% for both). The successful binding of levocetirizine was confirmed by X-ray photoelectron spectroscopy and infrared measurements. The active ingredient in the form of hydrochloride is more likely to be in the pores, while the free base is bound to the surface in larger quantities. The time-dependent levocetirizine release showed that the liberation of the active ingredient from the Syloid is slower than the dissolution of the starting active ingredient itself, so it may be suitable for exerting a more reliable and prolonged local effect. A gel containing a Syloid-fixed levocetirizine free base was tested in vivo in a croton oil-induced ear edema mouse model. When compared to a reference gel, the half-dose formulation containing levocetirizine free base demonstrated a similar efficacy to Fenistil gel, indicating that the new formulation may offer superior effectiveness at lower doses.

In this work, we study the influence of reduced graphene oxide (rGO) on the morphology and chemistry of highly porous N,S-doped carbon cryogels. Simultaneously, we propose an easily upscalable route to prepare such carbons by adding graphene oxide (GO) in as-received suspended form to the aqueous solution of the ι-carrageenan and urea precursors. First, 1.25–5 wt% GO was incorporated into the dual-doped polymer matrix. The CO2, CO, and H2O emitted during the thermal treatments resulted in the multifaceted modification of the textural and chemical properties of the porous carbon. This facilitated the formation of micropores through self-activation and resulted in a substantial increase in the apparent surface area (up to 1780 m2/g) and pore volume (up to 1.72 cm3/g). However, adding 5 wt% GO led to overactivation. The incorporated rGO has an ordering effect on the carbon matrix. The evolving oxidative species influence the surface chemistry in a complex way, but sufficient N and S atoms (ca. 4 and >1 at%, respectively) were preserved in addition to the large number of developing defects. Despite the complexity of the textural and chemical changes, rGO increased the electrical conductivity monotonically. In alkaline oxygen reduction reaction (ORR) tests, the sample with 1.25 wt% GO exhibited a 4e− mechanism and reasonable stability, but a higher rGO content gradually compromised the performance of the electrodes. The sample containing 5 wt% GO was the most sensitive under oxidative conditions, but after stabilization it exhibited the highest gravimetric capacitance. In Li-ion battery tests, the coulombic efficiency of all the samples was consistently above 98%, indicating the high potential of these carbons for efficient Li-ion insertion and reinsertion during the charge–discharge process, thereby providing a promising alternative for graphite-based anodes. The cell from the 1.25 wt% GO sample showed an initial discharge capacity of 313 mAh/g, 95.1% capacity retention, and 99.3% coulombic efficiency after 50 charge–discharge cycles.

S and N double-doped high surface area biomass-derived carbons were obtained from marine biomass-derived ι-carrageenan. Adding carbon nanoparticles (CNPs), namely graphene oxide (GO) or carbon nanotubes (CNTs), in the early stage of the synthesis leads to a modified porous texture and surface chemistry. The porous textures were characterized by N2 (−196.15 °C) and CO2 (0 °C) isotherms. The best GO- and CNT-added carbons had an apparent surface area of 1780 m2/g and 1170 m2/g, respectively, compared to 1070 m2/g for the CNP-free matrix. Analysis of the Raman spectra revealed that CNT was more efficient in introducing new defects than GO. Based on XPS, the carbon samples contain 2–4.5 at% nitrogen and 1.1 at% sulfur. The Dubinin–Radushkevich (DR) and Henry models were used to assess the strength of the interactions between various gases and the surface. The N2/H2 and CO2/CH4 selectivities were estimated with ideal adsorbed solution theory (IAST). While the CNPs, particularly GO, had a remarkable influence on the porous texture and affected the surface chemistry, their influence on the separation selectivity of these gases was more modest.

The manufacturing process has been drastically influenced by the advent of three-dimensional (3D) printing as it enables complicated structures to be designed using customized features that traditional processing methods cannot handle. Simultaneously, graphene is increasingly being considered as a reinforcement material to be used for metals and polymers because of its exceptional properties. Although several studies have examined the additively manufactured graphene/polymer composite parts’ mechanical properties, few have explored how graphene affects the 3D printed polymers’ tribological properties considering friction and wear. Thus, the present study aims to examine the tribological behavior concerning 3D printed graphene/resin composite. For this, the digital light processing (DLP) technique is used. Graphene’s impact and the variation in the printing process parameters were assessed by considering aspects such as the surface roughness, microstructure, wear, friction, and hardness characteristics of the tested materials. According to the results, a considerable decrease was observed in the friction coefficient of graphene specimens (0.5 wt%) as it reduced by approximately 50% compared with pure resin material. The present study is unique as the quantity of added graphene (up to 2 wt%) was substantially more than what has typically been used in other studies concerning photopolymerization printing capability.

Metronidazole (MTZ) is a widely used drug, but due to its many side effects, there is a growing trend today to use a minimum dose while maintaining high efficacy. One way to meet this demand is to reduce the size of the drug particles. A relatively new method of size reduction is attaching the drug molecules to a mesoporous carrier. In this paper, we studied the fixation of MTZ molecules on mesoporous silica carriers. The drug was immobilized on two mesoporous silica materials (Syloid, SBA-15) with the use of a variety of immersion techniques and solvents. The immobilized drug was subjected to physicochemical examinations (e.g., SEM, XPS, XRD, nitrogen uptake, DSC) and dissolution studies. A significantly higher immobilization was attained on SBA-15 than on a Syloid carrier. Among the processing parameters, the type of MTZ solvent had the highest influence on immobilization. Ultrasonic agitation had a lower but still significant impact, while the concentration of MTZ in the solution made no difference. Under optimal conditions, with the application of an ethyl acetate solution, the surface coverage on SBA-15 reached as much as 91%. The immobilized MTZ exhibited a ca. 10% faster dissolution rate as compared to the pure micron-sized drug particles.

The development of delivery systems for the immobilization of nucleic acid cargo molecules is of prime importance due to the need for safe administration of DNA or RNA type of antigens and adjuvants in vaccines. Nanoparticles (NP) in the size range of 20–200 nm have attractive properties as vaccine carriers because they achieve passive targeting of immune cells and can enhance the immune response of a weakly immunogenic antigen via their size. We prepared high capacity 50 nm diameter silica@zirconia NPs with monoclinic/cubic zirconia shell by a green, cheap and up-scalable sol–gel method. We studied the behavior of the particles upon water dialysis and found that the ageing of the zirconia shell is a major determinant of the colloidal stability after transfer into the water due to physisorption of the zirconia starting material on the surface. We determined the optimum conditions for adsorption of DNA building blocks, deoxynucleoside monophosphates (dNMP), the colloidal stability of the resulting NPs and its time dependence. The ligand adsorption was favored by acidic pH, while colloidal stability required neutral-alkaline pH; thus, the optimal pH for the preparation of nucleic acid-modified particles is between 7.0–7.5. The developed silica@zirconia NPs bind as high as 207 mg dNMPs on 1 g of nanocarrier at neutral-physiological pH while maintaining good colloidal stability. We studied the influence of biological buffers and found that while phosphate buffers decrease the loading dramatically, other commonly used buffers, such as HEPES, are compatible with the nanoplatform. We propose the prepared silica@zirconia NPs as promising carriers for nucleic acid-type drug cargos.

Among microporous storage materials copper benzene-1,3,5-tricarboxylate (CuBTC MOF, Cu3(BTC)2 or HKUST-1) holds the greatest potential for clean energy gases. However, its usefulness is challenged by water vapor, either in the gas to be stored or in the environment. To determine the protection potential of graphene oxide (GO) HKUST-1@GO composites containing 0–25% GO were synthesized and studied. In the highest concentration, GO was found to strongly affect HKUST-1 crystal growth in solvothermal conditions by increasing the pH of the reaction mixture. Otherwise, the GO content had practically no influence on the H2, CH4 and CO2 storage capacities, which were very similar to those from the findings of other groups. The water vapor resistance of a selected composite was compared to that of HKUST-1. Powder X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), thermogravimetric (TG/DTG) and N2 adsorption techniques were used to monitor the changes in the crystal and pore structure. It was found that GO saves the copper–carboxyl coordination bonds by sacrificing the ester groups, formed during the solvothermal synthesis, between ethanol and the carboxyl groups on the GO sheets.

Cellulose acetate was modified with caprolactone in an internal mixer at temperatures between 120 and 220 °C, and reaction times between 5 and 45 min in the presence of tinoctoate catalyst. The effect of plasticization on the properties of the polymer was studied by dynamic mechanical analysis and tensile testing. The dynamic mechanical spectrum of cellulose acetate exhibits three main relaxation transitions. These can be assigned to segments (α), to smaller structural units of the main chain, probably individual glucose rings (β), and to hydroxyl or hydroxylmethyl groups (γ). Plasticization by caprolactone leads to the decrease of the glass transition temperature of CA, but also to the breakdown of relatively large segments to smaller structural units. Free hydroxyl groups interact with the plasticizer forming larger units with higher transition temperature. Grafting decreases the intensity of the γ‐transition peak. External plasticization creates a larger number of small structural units, but the external plasticizer is less efficient in the decrease of stiffness than grafted polycaprolactone chains. Internal plasticization is more advantageous because it leads to higher flexibility at larger strength than external plasticization, and the migration of the plasticizer is prevented at the same time. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 873–883, 2007 [ABSTRACT FROM AUTHOR]