Search

In solar thermal plants, the use of molten salt as a heat transfer fluid is an advantageous alternative, although it has some disadvantages such as the formation of salt plugs in the pipes due to possible stratification of the salt or its solidification. The aim of this study was to implement an electromagnetic acoustic transducer (EMAT) not only capable of identifying the position of the plug, but also of determining whether the plug blocks the entire conductive surface or, on the contrary, is partial, allowing the fluid to pass through a smaller section. The proposed transducer is intended to be minimally invasive, allowing it to be used in the same way as a temperature probe. To do so, it creates torsional waves in the pipe, which are then used for a combination of measurements: pulse-echo and attenuation of the acoustic waves. Two materials with different densities (silicone and cement) were used in the tests carried out, which made it possible to check that for a given size of blockage, it is possible to identify the type of material from which it is formed.

Capacitive De-Ionization (CDI) is becoming a suitable alternative for desalination. The low cost of the materials required and its reduced energy consumption can be critical factors for developing this technique. CDI technology does not require a high-pressure system and the energy storage capability of CDI cells allows it to be reused in other CDI cells, thus minimizing consumption. The goal of the power stage responsible of the energy recovery is transferring the stored energy from one cell to another with the maximum possible efficiency, thus allowing the desalination process to continue. Assuming hysteresis current control is implemented at the DC/DC (direct current) converter, this paper aims to determine the optimum peak current through the inductor in each switching period with a view to maximizing overall efficiency. The geometrical parameters of the desalination cell and the NaCl concentration modify the cell electrical properties. The peak current control of the power stage should be adapted to the cell characteristics so that the efficiency behavior of the whole CDI system can be improved. The mathematical model defined in this paper allows the CDI plant automation using the peak inductor current as control variable, adapting its value to the salt concentration during the desalination process.

With photovoltaic (PV) systems proliferating in the last few years due to the high prices of fossil fuels and pollution issues, among others, it is extremely important to monitor the efficiency of these plants and optimize the energy production process. This will also result in improvements related to the maintenance and security of the installation. In order to do so, the main parameters in the plant must be continuously monitored so that the appropriate actions can be carried out. This monitoring should not only be carried out at a global level, but also at panel-level, so that a better understanding of what is actually happening in the PV plant can be obtained. This paper presents a system based on a wireless sensor network (WSN) that includes all the components required for such monitoring as well as a power supply obtaining the energy required by the sensors from the photovoltaic panels. The system proposed succeeds in identifying all the nodes in the network and provides real-time monitoring while tracking efficiency, features, failures and weaknesses from a single cell up to the whole infrastructure. Thus, the decision-making process is simplified, which contributes to reducing failures, wastes and, consequently, costs.

A very interesting and useful complement to classical cash-registers is presented in this paper, coming up with a real-time auto-counting solution for the money inside a cash drawer. The system allows knowing not only the total amount of money but also how many coins and banknotes there are of each value. The embedded solution developed has been intended to become a low-cost solution, allowing better control over the money and helping both owners and workers in the establishments. By using this system, new utilities including automatic final balancing, instant error handling when making operations, and the lack of certain types of banknotes or coins inside the drawer or the excess of some in a certain compartment, could be implemented. Coins-counting solution is based on their weight, and small individual scales made by load cells have been integrated in each coin compartment. With respect to the banknotes, an innovative alternative based on the electrical properties of capacitors is presented. Additionally, considering the relevance of interoperability in today’s systems, a Bluetooth module has been integrated into the system, allowing for data to be accessed remotely from any smartphone, tablet or computer within the range of the module. In this work, an Android application to both control and interact with the system has also been designed.

The use of solar thermal power plants is considered a cost-effective alternative to produce renewable energy. Unlike other energy installations, in this type of plants the transfer and storage of energy has been solved by using molten salts. These salts run between two tanks through the steam generation system that feeds the turbine. Although the use of salts as a heat transfer fluid is considered an adequate solution, they are not without problems. One of them is the formation of blockages in the pipes due to a partial solidification of the salt, which leads to the shutdown of the installation, with the consequent economic losses. Fast location of these blockages in a minimally intrusive way is the objective pursued in this work. The method to achieve this is based on the use of a new magnetostrictive sensor that simplifies previous designs.

In solar thermal power plants molten salt is often used to store and transport the energy that is collected during the day. The external pipe temperature is measured to activate an electric heating system if the temperature approaches the melting point. However, salt solidification cannot be completely excluded from the plant management. Once occurred, the location of a salt blockage is very complex due to the high temperature of the pipe. Therefore, when this problem arises, power plants have to stop production with the consequences in time and cost that this entails. Electro-magnetic acoustic transducers can be used as non-destructive testing systems for this application. A method for salt blockage detection is proposed that is applicable in straight sections of pipes by employing torsional guided waves that are generated with magnetostrictive transducers. The present paper deals with the transducer conception and the design of the power supply to activate it. Two alternatives are proposed and compared to determine the improvement in the amplitude/noise ratio. Finally, the experimental results show the performance of the equipment in a small prototype, thus validating the technique presented.

Electrostatic precipitators (ESPs) are devices used in industry to eliminate polluting particles in gases. In order to supply them, an interface must be included between the three-phase main line and the required high DC voltage of tens of kilovolts. This paper describes an 80-kW power supply for such an application. Its structure is based on the series parallel resonant converter with a capacitor as output filter (PRC-LCC), which can adequately cope with the parasitic elements of the step-up transformer involved. The physical implementation of the prototype includes the use of silicon carbide—SiC—semiconductors, which provide better switching capabilities than their traditional silicon—Si—counterparts. As a result, a new control strategy results as a better alternative in which the resonant current is maintained in phase with the first harmonic of the inverter voltage. Although this operation mode imposes hard switching in one of the inverter legs, it minimizes the reactive energy that circulates through the resonant tank, the resonant current amplitude itself and the switching losses. Overall efficiency of the converter benefits from this. These ideas are supported mathematically using the steady state and dynamic models of the topology. They are confirmed with experimental measurements that include waveforms, Bode plots and thermal behavior. The experimental setup delivers 80 kW with an estimated efficiency of 98%.

Medical X-ray appliances use high-voltage power supplies that must be able to work with very different energy requirements. Two techniques can be distinguished in X-ray medical imaging: fluoroscopy and radioscopy. The former involves low power radiation with a long exposure time, while radioscopy requires large power during short radiographic exposure times. Since the converter has to be designed by taking into account the maximum power specification, it will exhibit a poor efficiency when operating at low power levels. Such a problem can be solved by using a new multilevel LCC topology. This topology is based on a classical series-parallel resonant topology, but includes an additional low-voltage auxiliary transformer whose function depends on the X-ray technique considered. When radioscopy operation is selected, the transformer will allow the power to be shared between two full-bridges. If fluoroscopy mode is activated, the auxiliary full bridge is disconnected and the magnetizing inductance of the auxiliary transformer is used to increase the resonant inductor in order to reduce the resonant currents, thus improving the efficiency of the converter.