Search

Design for deconstruction (DfD) considers the end-of-life scenario of buildings at an early design stage to ensure that these buildings (or parts of the buildings) can be deconstructed without unproportional effort and material loss. After deconstruction, the elements or materials can be used for future purposes such as reusing (preferably), remanufacturing, or recycling. This opinion paper is aimed to advocate for DfD in timber–concrete composite (TCC) floors as it represents an important contribution toward circular economy design and creates a more sustainable built environment. Different end-of-life scenarios for TCC floors according to their original design and connection type were initially explored. Existing deconstructable connection systems that could enable DfD in TCC floors were reviewed. Furthermore, potential challenges relating to the implementation of DfD in TCC floors are briefly highlighted. Finally, a discussion around the outlook and actions that might be needed to address some of the identified challenges is provided. This paper proposes directions for future developments and contributes to the understanding and promotion of DfD in TCC floors with an emphasis on deconstructable connectors that can enable material recovery and reuse as the preferred end-of-life scenario.

Salvaged timber elements often have length limitations, and therefore, their reuse in structural products normally would require additional processing and end-to-end joining. This increases the costs of reusing such materials, which makes them even less attractive to the timber sector. In the presented research, a new approach is proposed for reusing short, salvaged timber elements combined with new (full-scale) timber boards to fabricate dowel-laminated timber (DLT) panels without significant processing or end-to-end joining or gluing. In this approach, salvaged timber elements are pressed in the system in such a way that they can contribute to the bending performance of the DLT panels by resisting compression stress. In order to evaluate the effectiveness, several small-scale and large-scale DLT panels were fabricated. Salvaged plywood tenons were used as connectors. The bending stiffness of the small-scale DLT panels and the first eigenfrequency, damping ratio, bending properties, and failure modes of the large-scale DLT panels were evaluated. The results exhibited that by using the proposed approach, the short, salvaged timber elements can contribute substantially to the bending stiffness of the DLT panels without requiring end-to-end joining or gluing. On average, about a 40% increase in the bending stiffness could be achieved by pressing in the salvaged timber elements, which results in relatively similar stiffness properties compared to conventional DLT panels. One further characteristic is that the failure of the panels, and therefore the panel’s strength, is mainly governed by the quality of the full-scale timber boards instead of the salvaged ones. This can be beneficial for practical use as the qualitative assessment of the strength properties of salvaged timber becomes less critical.

About one million hectares of plantation hardwoods, mostly eucalyptus trees of different sub-species (E. nitens and E. globulus), are annually being managed in Australia, which provides a promising resource of raw materials for fibre industries. However, the timber boards required by the Australian hardwood sector are still being either imported from other countries or harvested from the native forests. There is a need to find a practical way to use the plantation eucalyptus in the Australian timber industry. However, the fibre-managed plantation eucalyptus produces structurally low-grade timber which could not be used as individual boards for structural applications—such as building construction. Unsuitable for appearance applications, the structurally low-grade boards may be suitable for producing innovative high-mass engineered timber products. This editorial will briefly discuss drivers, opportunities, and challenges associated with conducting such a research project.

An experimental method was developed in this investigation to evaluate the shear strength of adhesive bonds in solid wood materials. The new method was tested against the standard test methods described in ASTM D-905, EN 205, and EN 302-1. Specimens were constructed of Oriental Beech (Fagus orientalis L.) and bonded with three different wood adhesives. Using the proposed method in the study, unintentional errors in cutting and testing processes of the shear specimens were decreased, which led to a decrease in the variability of the results. The worst stability was observed in the data obtained when the EN 205 and ASTM D-905 standard methods were used.

The impact of fastener type (glued and unglued butterfly dovetail keys, glued and unglued H-shaped dovetail keys, one-pin dowel, two-pin dowels, and plywood spline) and wood composite material type on the bending moment capacity of L-shaped mitered frame joints under diagonal tension and compression loads was investigated. Specimens were constructed of laminated medium-density fiberboard (LamMDF) and laminated particleboard (LamPB). The glued joint specimens were constructed with polyvinyl acetate (PVAc) adhesive. In both tests, joints reinforced with two dowels had the highest bending moment capacity, whereas unglued joints fastened with H-shaped dovetail keys had the lowest capacity. Splined joints were characterized by the second highest bending moment capacity. Two-pin dowel joints had, on average, 47% greater capacity than one-pin dowel joints. The glued dovetail joints were 31% stronger than the unglued joints. There was no statistically significant difference between the bending moment capacities of butterfly and H-shaped dovetail keys. The LamMDF joints exhibited 7.8% greater capacity than joints constructed of LamPB. Overall, the bending moment capacity of joints loaded in compression was 22% higher than that of joints loaded in tension—when the moment arm in the compression specimens was taken at the inside corner of the joint.

This study tested the machinability of three major timber species grown in Tasmania, Australia, under different resource management schemes: plantation fiber-managed hardwood (Eucalyptus globulus Labill. and Eucalyptus nitens Maiden) and plantation sawlog-managed softwood (Pinus radiata D. Don). P. radiata was used as a control to identify significant differences in machining fibre-managed plantation timber against sawlog-managed plantation timber with numerically controlled computer technology and manually fed timber production techniques. The potential to fabricate architectural interior products such as moldings with plantation fiber-managed hardwood timber that is high in natural features was the focus of this study. Correlations between wood species, variation in moisture content, and density of individual machinability characteristics were analyzed to determine factors impacting the overall quality of plantation wood machinability. Correlations between species and within species groups from the resulting machinability tests are highlighted and discussed. The results indicate that the machinability of sawlog-managed softwood P. radiata is superior in some circumstances to fiber-managed hardwood E. globulus and E. nitens specimens, according to the American Society for Testing and Materials D1666-11.

The use of fast-growing plantation eucalypt (i.e., pulpwood eucalypt) in the construction of high-value structural products has received special attention from the timber industry in Australia and worldwide. There is still, however, a significant lack of knowledge regarding the physical and mechanical properties of the lumber from such plantation resources as they are mainly being managed to produce woodchips. In this study, the physical and mechanical properties of lumber from a 16-year-old pulpwood Eucalyptus nitens H.Deane & Maiden resource from the northeast of Tasmania, Australia was evaluated. The tests were conducted on 318 small wood samples obtained from different logs harvested from the study site. The tested mechanical properties included bending modulus of elasticity (10,377.7 MPa) and modulus of rupture (53 MPa), shear strength parallel (5.5 MPa) and perpendicular to the grain (8.5 MPa), compressive strength parallel (42.8 MPa) and perpendicular to the grain (4.1 MPa), tensile strength perpendicular to the grain (3.4 MPa), impact bending (23.6 J/cm2), cleavage (1.6 kN) and Janka hardness (23.2 MPa). Simple linear regression models were developed using density and moisture content to predict the mechanical properties. The variations in the moisture content after conventional kiln drying within randomly selected samples in each test treatment were not high enough to significantly influence the mechanical properties. A relatively high variation in the density values was observed that showed significant correlations with the changes in the mechanical properties. The presence of knots increased the shear strength both parallel and perpendicular to the grain and significantly decreased the tensile strength of the lumber. The results of this study created a profile of material properties for the pulpwood E. nitens lumber that can be used for numerical modelling of any potential structural product from such a plantation resource.