Search

Stalk lodging contributes to significant crop yield losses. Therefore, understanding the biomechanical strength and structural rigidity of grain stalks can contribute to improving stalk lodging resistance in crops. From the structural constituents of the stalk, the rind provides the principal structure, supporting cells against tension and bending loads. In this work, the biomechanical and viscoelastic behavior of the rind from the internodes of two sweet sorghum varieties (Della and REDforGREEN (RG)), grown in two different growing seasons, were evaluated by three-point micro-bending tests using a dynamic mechanical analyzer (DMA). In addition, the chemical composition of rinds and the microfibril angle (MFA) of the cell wall were determined using XRD. The results revealed that the biomechanical behavior of Della varieties was stiffer and more resistant to loads than that of RG varieties. Two features of the rind biomechanical properties, flexural modulus (FM) and flexural strength (FS), showed a significant reduction for RG. Particularly, a reduction in FS of 16–37% and in FM of 22–41% were detected for RG1. Changes in the stalks' rind biomechanical properties were attributed to cell wall components. Total lignin and glucan/cellulose contents were positively correlated with the FM and FS of the rind. Subsequently, an increase in the two cell wall components drove an increase in stiffness. Furthermore, the MFA of the rind was also found to influence the rind strength. [ABSTRACT FROM AUTHOR]

This study examined the use of softwood mill residues (50–90%) with two thermosetting resins (i) urea-formaldehyde (UF) and (ii) phenol-resorcinol-formaldehyde (PRF) resin, for potential use in additive manufacturing (AM) of wood composite materials. The curing behavior of these blends was evaluated using differential scanning calorimetry and dynamic rheology. Curing kinetics was determined using the Kissinger and Cranes method. The presence of wood fibers reduced the curing peak temperatures for both resin blends at the same heating rates but curing peak temperatures increased with heating rates. The activation energy (Ea) increased with the addition of wood for the wood-PRF blends but reduced for the wood-UF blends in comparison to the neat resins. Ea values were 51 and 271 kJ/mol for PRF and wood-PRF samples and 100 and 367 kJ/mol for UF and wood-UF samples. Frequency sweep flow curves of the green wood-resin blends showed shear thinning behaviors with viscosity values between 103–108 Pa.s at 30°C. Mechanical properties of the wood-resin composites generally showed a reduction in flexural modulus with an increase in wood content. Wet wood (50%)-PRF blend was successfully extruded and showed promise for use in AM; however, the wood-UF blend was not successful. [ABSTRACT FROM AUTHOR]

This study investigated the efficacy of lauric arginate (LAE) as a potential preservative against wood deteriorating fungi. First, the antifungal properties of LAE against two brown rot fungi, Gloeophyllum trabeum (G.t.) and Rhodonia placenta (R.p.), and two white rot fungi, Trametes versicolor (T.v.) and Irpex lacteus (I.l.) were examined using malt-agar media as substrate. Then the biological resistance of LAE-treated wood specimens (10, 20, and 25 % LAE solutions) was tested following American Wood Protection Association (AWPA) E10 soil-block test procedures. The in vitro study showed LAE actively inhibited the growth of all the fungi tested compared to growth in control plates but there were no considerable changes observed in the morphology of fungi hyphae. Wood impregnated with LAE showed increased weight percent gain as a function of treatment concentration. Characterization of LAE-treated wood on a thermogravimetric analyzer showed LAE shifted the thermal degradation temperatures to lower stages but did not significantly improve the thermal stability of the treated specimen. LAE in wood significantly suppressed fungus growth, leading to decreased mass loss but it also leached out from wood specimens during fungi exposure. [ABSTRACT FROM AUTHOR]

The aim of this study was to evaluate the use of waste natural fibers from milled hop bines and hemp stalks, without chemical treatment, and compare them to a commercial wood fiber for use in wood–plastic composite (WPC) materials. The fibers were characterized (density, fiber size and chemical composition). WPCs were produced by the extrusion of a blend of fibers (50%), high-density polyethylene (HDPE) and coupling agent (2%). The WPCs were characterized for their mechanical, rheological, thermal, viscoelastic and water resistance properties. Pine fiber was about half the size of hemp and hop fibers and thus had a higher surface area. The pine WPC melts had a higher viscosity than the other two WPCs. Additionally, the tensile and flexural strengths of the pine WPC were higher than those of hop and hemp WPCs. The pine WPC was also shown to have the least water absorption followed by hop and hemp WPCs. This study highlights that different lignocellulosic fibers influence their WPC properties. The properties of the hop- and hemp-based WPCs were comparable to commercial WPCs and can be improved by further milling/screening the fibers to a smaller particle size (volumetric mean of ~88 μm) to increase their surface area, fiber–matrix interactions and improve stress-transfer. [ABSTRACT FROM AUTHOR]

Despite its massive potential, Raman imaging represents just a modest fraction of all research and clinical microscopy to date. This is due to the ultralow Raman scattering cross-sections of most biomolecules that impose low-light or photon-sparse conditions. Bioimaging under such conditions is suboptimal, as it either results in ultralow frame rates or requires increased levels of irradiance. Here, we overcome this tradeoff by introducing Raman imaging that operates at both video rates and 1,000-fold lower irradiance than state-of-the-art methods. To accomplish this, we deployed a judicially designed Airy light-sheet microscope to efficiently image large specimen regions. Further, we implemented subphoton per pixel image acquisition and reconstruction to confront issues arising from photon sparsity at just millisecond integrations. We demonstrate the versatility of our approach by imaging a variety of samples, including the three-dimensional (3D) metabolic activity of single microbial cells and the underlying cell-to-cell variability. To image such small-scale targets, we again harnessed photon sparsity to increase magnification without a field-of-view penalty, thus, overcoming another key limitation in modern light-sheet microscopy [ABSTRACT FROM AUTHOR]