Search

A novel active vibration control technique based on positive position feedback method is developed. This method, which is a modified version of positive position feedback, employs a first-order compensator that provides damping control and a second-order compensator for vibration suppression. In contrast, conventional positive position feedback uses a single second-order compensator. The technique is useful for strain-based sensors and can be applied to piezoelectrically controlled systems. After introducing the concept of modified positive position feedback, this paper investigates the stability of the new method for locating gain limits. Stability conditions are global and independent of the dynamical characteristics of the open-loop system. Using root locus plots, proper compensator frequency is identified and damping of the closed-loop system is studied. The performance of the modified positive position feedback for both steady-state and transient dynamic control is studied. The experimental and numerical results show that the proposed method is significantly more effective in controlling steady-state response and slightly advantageous for transient dynamics control as compared with conventional positive position feedback. [DOI: 10.1115/1.3089565] Keywords: active control vibration compensation, positive position feedback, first-order compensator, second-order compensator

The problem of vibrations of microcantilevers has recently received considerable attention due to its application in several nanotechnological instruments, such as atomic force microscopy, nanomechanical cantilever sensors, and friction force microscopy. Along this line, this paper undertakes the problem of coupled flexural-torsional nonlinear vibrations of a piezoelectrically actuated microcantilever beam as a typical configuration utilized in these applications. The actuation and sensing are both facilitated through bonding a piezoelectric layer (here, ZnO) on the microcantilever surface. The beam is considered to have simultaneous flexural, torsional and longitudinal vibrations. The piezoelectric properties combined with nonlinear geometry of the beam introduce both linear and nonlinear couplings between flexural vibration as well as longitudinal and torsional vibrations. Of particular interest is the inextensibility configuration, for which the governing equations reduce to coupled flexural-torsional nonlinear equations with piezoelectric nonlinearity appearing in quadratic form while inertia and stiffness nonlinearities as cubic. An experimental setup consisting of a commercial piezoelectric microcantilever installed on the stand of an ultramodern laser-based microsystem analyzer is designed and utilized to verify the theoretical developments. Both linear and nonlinear simulation results are compared to the experimental results and it is observed that nonlinear modeling response matches the experimental findings very closely. More specifically, the softening phenomenon in fundamental flexural frequency, which is due to nonlinearity of the system, is analytically and experimentally verified. It is also disclosed that the initial twisting in the microcantilever can influence the value of the flexural vibration resonance. The experimental results from a macroscale beam are utilized to demonstrate such twist-flexure coupling. This unique coupling effect may lead to the possibility of indirect measurement of small torsional vibration without the need for any angular displacement sensor This observation could significantly extend the application of friction force microscopy to measure the friction of a surface indirectly. [DOI: 10.1115/l.2948379] Keywords: nonlinear vibration of microcantilever beams, coupled flexural-torsional vibrations, piezoelectrically-actuated microcantilevers, friction force microscopy

The equations of motion for a piezoelectric microcantilever are derived for a nonlinear contact force. The analytical expressions for natural frequencies and mode shapes are obtained. Then, the method of multiple scales is used to analyze the analytical frequency response of the piezoelectric probe. The effects of nonlinear excitation force on the microcantilever beam's frequency and amplitude are analytically studied. The results show a frequency shift in the response resulting from the force nonlinearities. This frequency shift during contact mode is an important consideration in the modeling of AFM mechanics for generation of more accurate imaging. Also, a sensitivity analysis of the system parameters on the nonlinearity effect is performed. The results of a sensitivity analysis show that it is possible to choose parameters such that the frequency shift minimizes. Certain parameters such as tip radius, microcantilever beam dimensions, and modulus of elasticity have more influence on the nonlinearity of the system than other parameters. By changing only three parameters--tip radius, thickness, and modulus of elasticity of the microbeam--a more than 70% reduction in nonlinearity effect was achieved. [ABSTRACT FROM AUTHOR]

Improvement of microcantilever-based sensors and actuators chiefly depends on their modeling accuracy. Atomic force microscopy (AFM) is the most widespread application of microcantilever beam as a sensor, which is usually influenced by the tip-sample interaction force. Along this line of reasoning, vibration of AFM microcantilever probe is analyzed in this paper, along with analytical and experimental investigation of the influence of the sample interaction force on the microcantilever vibration. Nonlinear integropartial equation of microcantilever vibration subject to the tip-sample interaction is then derived and multiple time scales method is utilized to estimate the tip amplitude while it is vibrating near the sample. A set of experiments is performed using a commercial AFM for both resonance and nonresonance modes, and the results are compared with the theoretical results. Hysteresis, instability and amplitude drop can be identified in the experimental curves inside the particle attraction domain. They are likely related to the interaction force between the tip and sample as well as the ever-present water layer during the experiments. A fair agreement is observed between the theoretical simulations and experimental findings, which obviously demonstrates the effectiveness and applicability of the developed model. [ABSTRACT FROM AUTHOR]

This paper proposes a new leader–follower-based consensus vibration controller to actively suppress unwanted oscillations in distributed-parameter flexible structures. Actuation and sensing is performed via piezoelectric layers in a collocated sense. The actuator/sensor patches for the vibration control system are considered to collaborate in a network, and follow a virtual leader which is accessible to all agents. Hence, a vibration controller law is defined, to remove disagreement between agents and force the agents to follow the virtual leader. The proposed approach is an observer-based design, in which an optimal consensus state estimator is initially designed. Stability of the closed-loop system is investigated and the optimality conditions of the system are derived. Although the designed vibration controller could be implemented for suppression tasks in different distributed-parameter systems, a flexible clamped-clamped beam is used here for equation derivation and numerical performance verification. According to the results, the optimal observer estimates the system states in a finite time, as expected, and the vibration controller suppresses unwanted oscillations, either in resonant or arbitrary form, to a much lower level; while the disagreement between agents converges to zero. Additionally, suppression performance and robustness of the controller to failure in control system elements is investigated in comparison with a conventional positive position feedback controller, and its superiority is illustrated and discussed. [ABSTRACT FROM AUTHOR]

A new multi-piezoelectric microcantilever sensor is introduced in this article for replacing laser sensors in atomic force microscopes. This microcantilever consists of multiple piezoelectric layers over its surface, and a consensus algorithm is designed to provide a robust and accurate estimation of the deflections at the tip of the microcantilever. The dynamic equation set of the microcantilever is developed first and then the consensus observer is designed. A set of Riccati equations is used to obtain the optimal gains for the observer, and the robustness of the microcantilever is considered by designing a H∞ norm constraint. A set of numerical simulations is conducted to evaluate the performance of the microcantilever. Results show that the consensus-based multi-piezoelectric microcantilever can successfully provide an accurate estimation of the deflections at the tip of the microcantilever. It is also shown that the robustness of the design can positively improve the estimation performance in the presence of noise. Additionally, a comparison with a single-layered design shows the advantages of the new sensor. [ABSTRACT FROM AUTHOR]

This paper proposes a consensus state estimator for sensor networks of distributed parameter structures. A thin beam with clamped-clamped boundary conditions enhanced by piezoelectric sensors is considered, and individual observers are assigned for each of these sensors. The so-called estimation agents are then connected to one another in a network with certain directed topology, and consensus is enforced between the agents estimated output in observers dynamics. Observer gains are optimized using algebraic Riccati equations (AREs), and robustness to measurement disturbances is applied via H∞ design. The consensus state estimator is then numerically investigated for a sensor network of five agents. According to the results of the optimal and robust designs, the proposed consensus observer successfully estimates the modal system states in finite time, whereas the estimation output is resilient to measurement disturbances. Implementation of the consensus sensor network increases the robustness of the estimation, due to its inherent redundancy. [ABSTRACT FROM AUTHOR]

In this paper, H∞ modified positive position feedback (HMPPF) and H∞ modified positive velocity feedback (HMPVF) controllers are developed as two innovative controllers for active vibration reduction in flexible collocated structures. The controllers use the concept of modified positive feedback and are enhanced by the H∞ feedback design to provide effective vibration suppression of multiple modes. An aluminum cantilever beam is used to experimentally evaluate the performance of the two controllers. The objective of the HMPPF controller is to suppress vibration displacement when all of the fundamental modes are excited. In this case which considers the first three modes of the flexible structure, overall vibration displacement is reduced to 38% of the uncontrolled value. The HMPVF, on the other hand, uses the control energy to reduce the vibration velocity to the lowest possible value. Vibration velocity amplitude using the HMPVF approach was reduced more than displacement, which makes this controller more effective for fatigue failure prevention purposes. [ABSTRACT FROM AUTHOR]

Multimode modified positive position feedback (MMPPF) is proposed to suppress vibrations at multi-resonance frequencies in flexible collocated structures. Typically, flexible structures have large numbers of active modes in low frequency bandwidths, which make them susceptible to multi-frequency resonant vibrations. Hence, it is essential for the controller to have effective suppression on all participating modes. The MMPPF controller consists of a first- and a second-order compensator for each mode, as they are all set parallel for all active modes. Because of suppression performance sensitivity to controller gain parameters, proper gain selection is essential. Here, the linear quadratic regulator (LQR) approach and a proposed method called M-norm are used for gain optimization of the MMPPF controller. The optimized controller is then evaluated experimentally using a cantilever beam, enhanced by a piezoelectric actuator. According to the obtained results, the MMPPF controller reduces vibration amplitudes to the expected lower level, under both LQR and M-norm optimization methods. In some cases, vibration amplitude at the place of piezo-actuator is reduced to even less than the vibration amplitude level of the disturbance input at clamped end. [ABSTRACT FROM AUTHOR]

This paper develops H2 modified positive position feedback (H2-MPPF) and H∞-MPPF controllers for spatial vibration suppression of flexible structures in multimode condition. Resonant vibrations in a clamped-clamped (c-c) and a cantilever beam are aimed to be spatially suppressed using minimum number of piezoelectric patches. These two types of beams are selected since they are more frequently used in macro- and microscale structures. The shape functions of the beams are extracted using the assumed-modes approach. Then, they are implemented in the controller design via spatial H2 and H∞ norms. The controllers are then evaluated experimentally. Vibrations of multiple points on the beams are concurrently measured using a laser vibrometer. According to the results of the c-c beam, vibration amplitude is reduced to less than half for the entire beam using both H2- and H∞-MPPF controllers. For the cantilever beam, vibration amplitude is suppressed to a higher level using the H2-MPPF controller compared to the H∞-MPPF method. Results show that the designed controllers can effectively use one piezoelectric actuator to efficiently perform spatial vibration control on the entire length of the beams with different boundary conditions. [ABSTRACT FROM AUTHOR]

The nonlinear vibrations of the tapping-mode atomic force microscopy probe are investigated due to both nonlinearity in tip–sample contact force and curvature of the microcantilever probe. The nonlinear equations of motion for vibrations of the probe are obtained using Hamilton’s principle. In this work, the contact force is considered to be more dominant while previous works only consider Van der Waals force. The nonlinear contact force is expanded using a Taylor series to provide a polynomial with coefficients that are functions of the tip–sample distance. The outcome of this work allows the proper distance to be chosen before scanning to avoid instability in the response. Instability regions must be avoided for accurate imaging. The results show that initial tip–sample distance has a major effect on the stability of the frequency response and force response curves. For analytical investigation, the mode shapes of the atomic force microscopy probe are derived based on the presence of the nonlinear contact force as a boundary condition at the free end of the probe. The frequency response curve is obtained using the method of multiple scales. The results show that the effects of the nonlinearities due to probe geometry and contact force can be minimized. Minimizing the effects of nonlinearities allows for less cumbersome and calculation intensive software packages for atomic force microscopies. This research shows that one possible method of decreasing the nonlinearity effect is increasing the excitation force; however, this can increase the contact region and is not the best solution for canceling the nonlinearity effect. The superior method which is the major contribution of this paper is to find the optimal initial tip–sample distance and excitation force that minimize the nonlinearity effect. It is shown that at a certain tip–sample distance the quadratic and cubic nonlinearities cancel each other and the system responds linearly. [ABSTRACT FROM PUBLISHER]

Nonlinear vibrations of viscoelastic microcantilevers with a piezoelectric actuator layer on the top surface are investigated. In this work, the microcantilever follows a classical linear viscoelastic model, i.e., Kelvin-Voigt. In addition, it is assumed that the microcantilever complies with Euler-Bernoulli beam theory. The Hamilton principle is used to obtain the equations of motion for the microcantilever oscillations. Then, the Galerkin approximation is utilized for separation of time and displacement variables, thus the time function is obtained as a second order nonlinear ordinary differential equation with quadratic and cubic nonlinear terms. Nonlinearities appear in stiffness, inertia and damping terms. Using the method of multiple scales, the analytical relations for nonlinear natural frequency and amplitude of the vibration are derived. Using the obtained analytical relations, the effects of geometric factors and material properties on the free nonlinear behavior of this beam are investigated. The results are also verified by numerical analysis of the equations. [ABSTRACT FROM AUTHOR]

Abstract: Frequency response behavior of microcantilever is analytically and experimentally investigated in amplitude modulation Atomic Force Microscopy (AFM). AFM microcantilever probe is modeled as a continuous beam, and tip-sample interaction force is considered to include both attractive and repulsive force regimes. The developed model is compared with the linear lumped-parameters model that has been extensively used in the literature so far. Experimental measurements are also provided for the frequency response of a typical microcantilever-sample system to demonstrate the advantages of the developed model over the linear formulation. The results indicate that the nonlinear continuous model is more accurate, particularly in the estimation of the saturated amplitude value and frequency zone in which the tip-sample contact happens. [ABSTRACT FROM AUTHOR]

The modified positive position feedback (MPPF) controller, an active vibration control method that uses collocated piezoelectric actuator actuators and sensors, is developed using an adaptive controller. The adaptive mechanism consists of two main parts: (1) frequency adaptation and (2) adaptive controller. Frequency adaptation only tracks the frequency of vibrations using fast Fourier transforms. The obtained frequency is then fed to MPPF compensators and the adaptive controller. This provides a unique feature for MPPF by extending its domain of capabilities from controlling tonal vibrations to broadband disturbances. The adaptive controller mechanism consists of a reference model that is of the same order as the MPPF system and its compensators. The adaptive law provides the additional control force that is needed for controlling frequency changes caused by broadband vibrations. The experimental results show that the frequency adaptation method that is derived has worked quite well. The results also indicate that the MPPF can provide significant vibration reduction on a cantilever beam that is used throughout the experiments. [ABSTRACT FROM AUTHOR]

Despite the widespread adoption of membrane technologies for efficient water treatment, membrane fouling remains a significant challenge, reducing separation efficiency, shortening lifespan, and increasing operational costs. Various studies have explored chemical membrane modifications to mitigate fouling, often resulting in adverse effects on flux and selectivity. Based on numerical modeling and experimental investigation, this work introduces real-time induced magnetic vibration as a sustainable approach for membrane antifouling without compromising permeability and selectivity. By preventing or delaying particle deposition on the membrane surface, magnetic vibration reduces fouling intensity. Experimental results demonstrated that different frequencies of magnetic vibration influenced the deposition of foulants (Humic Acid and Sodium Alginate) on the membrane surface. Notably, vibrating the membrane at 10 Hz with centrally attached iron particles led to a 22.4 % reduction in flux when treated with Humic Acid, compared to a 33.9 % reduction without vibration. Exposure to vibrations at the resonance frequency (5 Hz) for 6 h resulted in only a 10 % reduction in flux, effectively preventing the formation of a dense cake layer. Similarly, in the case of Sodium Alginate, a 10 Hz vibration for 2 h decreased the flux reduction from 21.4 % without vibration to 7.3 %, suggesting the preventive effect of vibration on aggregated SA deposition or facilitating continuous displacement for flux retention. Moreover, the study examined the influence of the configuration of iron particles attached to the membranes on the effectiveness of vibration. The study revealed that a striped configuration was more effective than a centralized configuration, owing to the distributed vibration effect across each part of the membrane. Furthermore, the fouling mechanism and rejection percentage were further investigated to enhance understanding of the fouling processes. [Display omitted] • Real-time induced vibration prevents the cake layer formation. • Vibration at the resonance frequency of the membrane provides the maximum antifouling. • The position of magnetic particles in/on the membrane affects the vibration effectiveness. [ABSTRACT FROM AUTHOR]