Search

The present project investigated the hygrothermal performance and risk of mould growth in solid masonry walls retrofitted internally with three diffusion-open bio-based insulation materials (two loose-fill cellulose and one hemp fibre), installed in test containers with controlled indoor climate. Focus was on bio-based insulation materials, as these are upcoming due to necessary CO2 reductions and because the hygroscopic properties of bio-based materials are different from traditional insulation materials like mineral wool therefore, some manufacturers claim a vapour barrier is unnecessary, even in relatively cold climates. The project was a large experimental study in two reefer containers with reconfigured facades, in which solid masonry walls with embedded wooden elements were constructed. The study focused on the conditions in the masonry/insulation interface and in the embedded wooden elements. The effect of hydrophobization and different indoor moisture loads were also investigated. Moreover, the bio-based insulation systems were compared with a wall insulated with the traditional mineral wool and vapour barrier system. Relative humidity and temperature were measured at several locations in the test walls for 1 year and 9 months. Measurements show that exposed masonry walls retrofitted internally with diffusion-open bio-based insulation materials resulted in unacceptably high moisture levels (>80% RH over longer periods). Lower moisture levels were observed when the internal insulation was combined with hydrophobization against wind-driven rain, but unacceptably high moisture levels still occurred (60%–70% in summer and 95%–100% in winter in the interface). Hydrophobization reduced the moisture levels in the interface and embedded wooden elements only in walls facing southwest, which is the direction with the most wind-driven rain. Mould growth tests showed no growth in the interface in walls insulated with cellulose insulation (mycometer surface value <25). Meanwhile growth was found in all four walls insulated with hemp fibre matts (mycometer surface value >400). [ABSTRACT FROM AUTHOR]

The number of buildings experiencing humidity problems and fungal growth appears to be increasing as energy-saving measures and changes in construction practices and climate become more common. Determining the cause of the problem and documenting the type and extent of fungal growth are complex processes involving both building physics and indoor mycology. New detection and identification methods have been introduced, and new fungal species have been added to the list of building-related fungi. However, the lack of standardised procedures and general knowledge hampers the effort to resolve the problems and advocate for an effective renovation plan. This review provides a framework for building inspections on current sampling methods and detection techniques for building-related fungi. The review also contains tables with fungal species that have been identified on commonly used building materials in Europe and North America (e.g., gypsum wallboard, oriented strand board (OSB), concrete and mineral wool). The most reported building-associated fungi across all materials are Penicillium chrysogenum and Aspergillus versicolor. Chaetomium globosum is common on all organic materials, whereas Aspergillus niger is common on all inorganic materials. [ABSTRACT FROM AUTHOR]

The study investigated the hygrothermal performance and risk of mould growth in two thermal insulation systems for internal retrofitting purposes; a phenolic foam system with a closed cell structure, and a capillary active diffusion-open lime-cork based insulating plaster. The setup consisted of a 40-feet (12.2 m) insulated reefer container with controlled indoor climate, reconfigured with several holes (1x2 m each) containing solid masonry walls with embedded wooden elements on the interior side and different interior insulation systems, with and without exterior hydrophobisation. Focus was on the conditions in the interface between wall and insulation system, and in the embedded wooden elements. Relative humidity and temperature were measured in several locations in the test walls over two years, and the mould risk was evaluated by measurements and the VTT mould growth model. Findings for the interior phenolic foam system indicated that exposed walls experienced high relative humidity and high risk of moisture-induced problems. Exterior hydrophobisation had a positive effect on the moisture balance for the southwest oriented wall with phenolic foam. The lime-cork based insulating plaster showed high relative humidity and risk of moisture-induced problems, with and without hydrophobisation.

This project investigated fungal growth conditions in artificially contaminated interfaces between solid masonry and adhesive mortar for internal insulation. The project comprised several laboratory experiments: test of three fungal decontamination methods; investigation of development of fungal growth in solid masonry walls fitted with five internal insulation systems; and investigation of volatile organic compounds (VOC) diffusion through materials and whole insulation systems. One aim was to examine whether the alkaline environment (pH > 9) in the adhesive mortars could prevent fungal growth despite the water activity (aw) in the interface exceeds the level (aw > 0.75) commonly considered critical for fungal growth. The findings indicate that do‐it‐yourself decontamination solutions were inadequate for removal of fungal growth, while professional solutions were successful. However, the choice of decontamination method was of minor importance in the case of application of internal insulation with high pH adhesive mortar, as the high pH adhesive mortars were found to inactivate existing growth and prevented spore germination during the experimental period. The three tested VOCs were capable of diffusing through most of the examined products and could potentially affect the indoor air quality. [ABSTRACT FROM AUTHOR]

The study investigated the hygrothermal performance and risk of fungal growth in a phenolic foam system with a closed cell structure and a diffusion-open and capillary active lime-cork based insulating plaster, for internal retrofitting purposes. The setup comprised two 40-feet (12.2 m) insulated reefer container with controlled indoor climate, reconfigured with 24 holes (1 × 2 m each) containing solid masonry walls with embedded wooden elements on the interior side. Focus was on the conditions in the masonry/insulation interface and embedded wooden elements, and the performance of the two systems were compared to three diffusion-open insulation systems and one diffusion-tight. The effect of exterior hydrophobisation was also investigated. Relative humidity and temperature were measured in several locations in the test walls over 2½ years, and the risk of fungal growth was evaluated by on-site measurements and the VTT mould-growth model. The findings indicate that internally insulated walls with bare brick exterior surfaces performed poorly with high risk of fungal growth. The effect of exterior hydrophobisation was found to vary with the orientation and the installed insulation system, with a generally positive effect on walls facing south-west but limited effect for north-east. Furthermore, the more diffusion-tight insulation systems were found to perform better in combination with exterior hydrophobisation than the highly diffusion-open systems. The lime-cork insulating plaster showed high relative humidity and risk of moisture-induced problems. The on-site fungal tests showed no growth in the masonry/insulation interface inside the two insulation systems, probably due to high initial pH-value. [ABSTRACT FROM AUTHOR]

The objective of this study was to test whether compliance with the current Danish best practice recommendations concerning design of the cold attic space will prevent damaging moisture levels. The project was performed as a full-scale experimental setup in the cool temperate climate of Denmark. The setup comprised 18 north-facing attic spaces with varying ventilation principles and varying infiltration scenarios. The relative humidity and temperature were measured in attic spaces, indoor and outdoor, for almost 3 years. The hygrothermal performance of the attics was evaluated by post-processing and comparing the data with predicted mould growth risk and with visual observations of mould growth. The results showed that following the recommended passive ventilation strategies made the hygrothermal performance in attics with diffusion-open roofing underlay worse. In addition, increasing vapour diffusion tightness of the roofing underlay made the hygrothermal performance of the cold attic spaces under the eaves worse, except for attics with passive ventilation but without infiltration. The hygrothermal performance of the attics with diffusion-tight roofing underlay was poor when combining infiltration and the assessed ventilation strategy. The performance of the same attic without infiltration showed that some degree of ventilation was needed. External roof insulation did not significantly improve the hygrothermal performance of the attic. [ABSTRACT FROM AUTHOR]

The present research project investigates the hygrothermal performance of four insulation systems for internal retrofitting solid masonry walls with embedded wooden wall plate and beam end. The study was carried out through numerical simulations calibrated with 2–4 years of measurements and material data from a large field experimental in the cool, temperate climate of Lyngby, Denmark. The experiment comprised two 40-foot insulated reefer containers reconfigured with 24 1 × 2 m holes, accommodating the solid masonry walls. The calibrated simulation models were used to investigate several untested design variations which included alternative brick and mortar types, masonry and insulation thickness, indoor moisture load and future climate conditions. The findings indicate that a reduction of the indoor moisture load would improve the hygrothermal performance in the interface between wall and insulation, and in the embedded wooden elements. Increased masonry thickness was seen to make the hygrothermal conditions worse due to increased drying time for the built-in moisture, while in the case of low initial moisture content, increased masonry thisckness improved the hygrothermal performance in the interface and embedded wooden elements. Increased insulation thickness also made the hygrothermal conditions worse. Regarding the brick and mortar types, the results showsed increased relative humidity in the critical locations in the case of high cement mortar compared to low cement mortar. The brick type was however found not to impact the relative humidity levels considerably. Robustness against future climate conditions was seen only for two of the four insulation systems, when combined with exterior hydrophobisation. • Hygrothermal assessment of four insulation systems for interior retrofitting of solid masonry based on numerical simulations calibrated with four years of measurements. • Investigation of the effect of varying brick and mortar types. • Investigation of the effect of increased masonry- and insulation thickness. • A reduction of the indoor moisture load improved the hygrothermal conditions. • Two systems were found robust against future climate conditions. [ABSTRACT FROM AUTHOR]