Search

Abstract Thickness-controlled transparent conducting films (TCFs) were fabricated by transfer printing a 100 nm thick Cu micromesh structure onto poly(vinyl alcohol) (PVA) substrates of different thicknesses (~ 50, ~ 80, and ~ 120 μm) to develop a lightweight transparent wearable heater with short response time. The Cu mesh-based TCF fabricated on a ~ 50 µm thick PVA substrate exhibited excellent optical and electrical properties with a light transmittance of 86.7% at 550 nm, sheet resistance of ~ 10.8 Ω/sq, and figure-of-merit of approximately 236, which are comparable to commercial indium tin oxide film-based transparent conductors. The remarkable flexibility of the Cu mesh-based TCF was demonstrated through cyclic mechanical bending tests. In addition, the Cu mesh-based TCF with ~ 50 μm thick PVA substrate demonstrated a fast Joule heating performance with a thermal response time of ~ 18.0 s and a ramping rate of ~ 3.0 ℃/s under a driving voltage of 2.5 V. Lastly, the reliable response and recovery characteristics of the Cu mesh/PVA film-based transparent heater were confirmed through the cyclic power test. We believe that the results of this study is useful in the development of flexible transparent heaters, including lightweight deicing/defogging films, wearable sensors/actuators, and medical thermotherapy pads.

We used capacitance–voltage (C–V), conductance–voltage (G–V), and noise measurements to examine the carrier trap mechanisms at the surface/core of an AlGaN/GaN nanowire wrap-gate transistor (WGT). When the frequency is increased, the predicted surface trap density promptly drops, with values ranging from 9.1 × 1013 eV−1∙cm−2 at 1 kHz to 1.2 × 1011 eV−1∙cm−2 at 1 MHz. The power spectral density exhibits 1/f-noise behavior in the barrier accumulation area and rises with gate bias, according to the 1/f-noise features. At lower frequencies, the device exhibits 1/f-noise behavior, while beyond 1 kHz, it exhibits 1/f2-noise behavior. Additionally, when the fabricated device governs in the deep-subthreshold regime, the cutoff frequency for the 1/f2-noise features moves to the subordinated frequency (~102 Hz) side.

Graphene oxide (GO) is one of the interesting ink materials owing to its fascinating properties, such as high dissolubility in water and high controllable electric properties. For versatile printing application, the viscosity of GO colloids should be controlled in order to meet the specific process requirements. Here, we report on the relatively rapid fabrication of viscosity-increased GO (VIGO) colloids mixed with electrophoretically deposited GO sheets (EPD-GO). As the GO colloid concentration, applied voltage, and deposition time increase, the viscosity of the GO colloids becomes high. The reason for the improved viscosity of GO colloids is because EPD-GO has parallel stacked GO sheets. The GO and VIGO colloids are compared and characterized using various chemical and structural analyzers. Consequently, our simple and fast method for the fabrication of GO colloids with enhanced viscosity can be used for producing inks for flexible and printed electronics.

Due to the increasing use of polypropylene-based nonwoven dust masks and air filters, environmental problems that occur due to the plastic pollution resulting from the disposal of these materials have also increased. Hence, an eco-friendly air filter based on PVA nanofibers (NFs) was fabricated by electrospinning on a nonwoven fabric, and its performance was evaluated as a filter capable of blocking or capturing particulate matter. The quality factor of the optimized PVA NF-based air filter was found to be 0.010606 Pa−1, which is lower than that of a HEPA filter (0.015394 Pa−1), but higher than that of a cabin air filter (0.010517 Pa−1) and a dust mask (0.009102 Pa−1). The contamination level of the PVA NF-based filter was analyzed by optical and structural analyses of the filter surface. Finally, the filter was soaked in water to selectively remove the contaminated PVA NF layer, and the remaining nonwoven fabric was able to be reused to make the filter.

Modern energy needs and the pressing issue of environmental sustainability have driven many research groups to focus on energy-generation devices made from novel nanomaterials. We have prepared platinum nanoparticle-decorated silicon nanowire/carbon core−shell nanomaterials (SiNW/C@Pt). The processing steps are relatively simple, including wet chemical etching to form the silicon nanowires (SiNWs), chemical vapor deposition to form the carbon shell, and drop-casting and thermal treatment to embed platinum nanoparticles (Pt NPs). This nanomaterial was then tested as the counter electrode (CE) in dye-sensitized solar cells (DSSCs). SiNW/C@Pt shows potential as a good electrocatalyst based on material characterization data from Raman spectroscopy and X-ray photoelectron spectroscopy (XPS). Raman spectroscopy shows that the surface reactivity of the SiNW/C is increased by the decoration of Pt NPs. These data also show that the carbon shell included both graphitic (sp 2 hybridization) and defective (sp 3 hybridization) phases of carbon. We achieved the minimum charge-transfer resistance of 0.025 Ω · cm 2 and the maximum efficiency of 9.46% with a symmetric dummy cell and DSSC device fabricated from the SiNW/C@Pt CEs, respectively.

To develop high-performance de- or anti-frosting/icing devices based on transparent heaters, it is necessary to study the evaporation-rate control of droplets on heater surfaces. However, almost no research has been done on the evaporation-rate control of liquid droplets on transparent heaters. In this study, we investigate the evaporation characteristics of water droplets on transparent heater surfaces and determine that they depend upon the surface wettability, by modifying which, the complete evaporation time can be controlled. In addition, we study the defrosting and deicing performances through the surface wettability, by placing the flexible transparent heater on a webcam. The obtained results can be used as fundamental data for the transparent defrosting and deicing systems of closed-circuit television (CCTV) camera lenses, smart windows, vehicle backup cameras, aircraft windows, and sensor applications.

In this study, we report for the first time on the convection phenomenon for the consistent and sensitive detection of target materials (particulate matter (PM) or gases) with a high-performance transparent heater. The high-performance transparent heater, based on Pt-decorated Ni micromesh, was fabricated by a combination of transfer printing process and Pt sputtering. The resulting transparent heater exhibited excellent mechanical durability, adhesion with substrates, flexibility, and heat-generating performance. We monitored the changes in the PM concentration and temperature in an airtight chamber while operating the heater. The temperature in the chamber was increased slightly, and the PM2.5 concentration was increased by approximately 50 times relative to the initial state which PM is deposed in the chamber. We anticipate that our experimental findings will aid in the development and application of heaters for sensors and actuators as well as transparent electrodes and heating devices.

Patterning of metal nanowires (NWs) is vital for the fabrication of NW-based, high-performance devices such as sensors, transparent conducting electrodes, and optoelectronics. However, the majority of existing patterning methods require complex and expensive technologies. For this reason, we report for the first time a facile and quick patterning method of silver (Ag) NWs using a magnetic printing method. We successfully demonstrated a patterned AgNW grid structure on a flexible substrate as transparent electrodes. The flexible AgNW grid electrode exhibited optical and electrical properties comparable to those of commercial transparent conducting electrodes. We believe our work will be broadly applicable to other NW-based devices such as sensors, energy storage devices, metadevices, nanoscale electronics, and optoelectronics. [ABSTRACT FROM AUTHOR]