Search

The microstructural features and mechanical properties of composites formed by spark plasma sintering (SPS) of Al + 20 vol.% Fe and Al + 20 vol.% Fe66Cr10Nb5B19 (glassy alloy) mixtures composed of micrometer-sized particles are presented. The interaction between the mixture components was studied by differential thermal analysis and through examining the microstructure of composites sintered at two different SPS pressures. When the pressure was increased from 40 MPa to 80 MPa, the thickness of the reaction products formed between the iron particles and aluminum increased due to a more intimate contact between the phases established at a higher pressure. When the metallic glass was substituted for iron, the pressure increase had an opposite effect. It was concluded that local overheating at the interface in the case of Al + 20 vol.% Fe66Cr10Nb5B19 composites governed the formation of the product layers at 40 MPa. The influence of the nature of reinforcement on the mechanical properties of the composites was analyzed, for which sintered materials with similar microstructural features were compared. In composites without the reaction products and composites with thin layers of the products, the hardness increased by 13–38% relative to the unreinforced sintered aluminum, the glassy alloy and iron inclusions producing similar outcomes. The effect of the nature of added particles on the hardness and compressive strength of composites was seen when the microstructure of the material was such that an efficient load transfer mechanism was operative. This was possible upon the formation of thick layers of reaction products. Upon compression, the strong glassy cores experienced fracture, the composite with the glassy component showing a higher strength than the composite containing core-shell structures with metallic iron cores. [ABSTRACT FROM AUTHOR]

Metallic-glass-reinforced metal matrix composites are a novel class of composite materials, in which particles of alloys with an amorphous structure play the role of reinforcement. During the fabrication of these composites, a crystalline metal is in contact with a multicomponent alloy of an amorphous structure. In the present work, the morphological features of the reaction products formed upon the interaction of Fe66Cr10Nb5B19 metallic glass particles with aluminum were studied. The composites were processed via spark plasma sintering (SPS), hot pressing or a combination of SPS and furnace annealing. The reaction products in composites with different concentrations of the metallic glass and different transformation degrees were examined. The products of the interaction of the Fe66Cr10Nb5B19 metallic glass with Al were observed as dense layers covering the residual alloy cores, needles of FeAl3 protruding from the dense shells as well as needles and platelets of FeAl3 distributed in the residual Al matrix. The possible role of the liquid phase in the structure formation of the reaction products is discussed. The formation of needle- and platelet-shaped particles presumably occurred via crystallization from the Al-Fe-based melt, which formed locally due to the occurrence of the exothermic reactions between aluminum and iron. At the same time, aluminum atoms diffused into the solid Fe-based alloy particles, forming an intermetallic layer, which could grow until the alloy was fully transformed. When aluminum melted throughout the volume of the composite during heating of the sample above 660 °C, a similar microstructure developed. In both Al–Fe66Cr10Nb5B19 and Al–Fe systems, upon the reactive transformation, pores persistently formed in locations occupied by aluminum owing to the occurrence of the Kirkendall effect. [ABSTRACT FROM AUTHOR]

When metals are modified by second-phase particles or fibers, metal matrix composites (MMCs) are formed. In general, for a given metallic matrix, reinforcements differing in their chemical nature and particle size/morphology can be suitable while providing different levels of strengthening. This article focuses on MMCs reinforced with metallic glasses and amorphous alloys, which are considered as alternatives to ceramic reinforcements. Early works on metallic glass (amorphous alloy)-reinforced MMCs were conducted in 1982–2005. In the following years, a large number of composites have been obtained and tested. Metallic glass (amorphous alloy)-reinforced MMCs have been obtained with matrices of Al and its alloys, Mg and its alloys, Ti alloys, W, Cu and its alloys, Ni, and Fe. Research has been extended to new compositions, new design approaches and fabrication methods, the chemical interaction of the metallic glass with the metal matrix, the influence of the reaction products on the properties of the composites, strengthening mechanisms, and the functional properties of the composites. These aspects are covered in the present review. Problems to be tackled in future research on metallic glass (amorphous alloy)-reinforced MMCs are also identified. [ABSTRACT FROM AUTHOR]

In metallic glass-reinforced metal matrix composites, the glassy phase can serve a dual purpose: (i) it can behave as soft binder and porosity remover during consolidation; and (ii) it can act as the hard reinforcing phase after densification. The present work aimed to demonstrate the benefit of the glassy reinforcing particles for the densification of aluminum matrix composites. The consolidation behavior of Al–50 vol.% Fe-based alloy mixtures prepared using a glassy Fe66Cr10Nb5B19 alloy powder (Tg = 521 °C, Tx = 573 °C) or a crystalline Fe62Cr10Nb12B16 alloy powder was studied under spark plasma sintering (SPS) and hot pressing (HP) conditions. The powders were consolidated by heating above the glass transition temperature of the glassy alloy (up to 540 °C in SPS and 570 °C in HP). When the coarse aluminum powder was used, the reinforcing particles formed chains within the microstructure. In composites formed from the fine Al powder, the particles of the Fe-based alloy were separated from each other by the metallic matrix, and the tendency to form agglomerates was reduced. The glassy state of the alloy was shown to be beneficial for densification, as the metallic glass acted as a soft binder. The densification enhancement effect was more pronounced in the case of reinforcing particles forming chains. The hardness of the Al–50 vol.% glassy Fe66Cr10Nb5B19 composites obtained by SPS was twice the hardness of the unreinforced sintered aluminum (110 HV1 versus 45 HV1). [ABSTRACT FROM AUTHOR]

Metal matrix composites (MMCs) are a constantly developing class of materials. Simultaneously achieving a high strength and a high ductility is a challenging task in the design of MMCs. This article aims to highlight a recent trend: the development of MMCs reinforced with particles of core–shell structure. The core–shell particles can be synthesized in situ upon a partial transformation of metal (alloy) particles introduced into a metal matrix. MMCs containing core–shell particles with cores of different compositions (metallic, intermetallic, glassy alloy, high-entropy alloy, metal-ceramic) are currently studied. For metal core–intermetallic shell particle-reinforced composites, the property gain by the core–shell approach is strengthening achieved without a loss in ductility. The propagation of cracks formed in the brittle intermetallic shell is hindered by both the metal matrix and the metal core, which constitutes a key advantage of the metal core–intermetallic shell particles over monolithic particles of intermetallic compounds for reinforcing purposes. The challenges of making a direct comparison between the core–shell particle-reinforced MMCs and MMCs of other microstructures and future research directions are discussed. [ABSTRACT FROM AUTHOR]

Abstract We have studied the phase and structure evolution of the Ti33Cu67 amorphous alloy subjected to electrical pulses of high current density. By varying the pulse parameters, different stages of crystallization could be observed in the samples. Partial polymorphic nanocrystallization resulting in the formation of 5- to 8-nm crystallites of the TiCu2 intermetallic in the residual amorphous matrix occurred when the maximum current density reached 9.7·108 A m-2 and the pulse duration was 140 μs, though the calculated temperature increase due to Joule heating was not enough to reach the crystallization temperature of the alloy. Samples subjected to higher current densities and higher values of the evolved Joule heat per unit mass fully crystallized and contained the Ti2Cu3 and TiCu3 phases. A common feature of the crystallized ribbons was their non-uniform microstructure with regions that experienced local melting and rapid solidification. PACS: 81; 81.05.Bx; 81.05.Kf.

Without the availability of slip systems and dislocation glide as in crystalline materials, metallic glasses resist irreversible deformation to elastic strains of 2% or more before undergoing heterogeneous plastic flow via the formation of shear bands. Observation of crystallite formation under compressive load was previously obtained by transmission electron microscopy. In this Letter, we present results of nondestructive x-ray diffraction microprofiling of the section of a bent glassy Pd40Cu30Ni10P20 ribbon in transmission using a synchrotron microbeam. Crystallization was clearly detected but only on the compression side of the neutral fiber. The experimental results and crystal nucleation frequency analysis are consistent with massive nucleation in shear bands forming under compressive stress but mainly for metallic glasses that show a large supercooled liquid temperature range &Dgr;T = Tx -- Tg between glass transition at Tg and crystallization at Tx. The phenomenon is sensitively dependent on the volume change that accompanies crystallization in the supercooled liquid temperature range where the much larger liquid-state thermal expansion coefficient significantly increases the specific volume difference between the liquid and crystalline states. The results are also consistent with the many reports of extensive strain to fracture of metallic glasses under compressive load but not under tension. [ABSTRACT FROM AUTHOR]

Ni- and Cu-free Zr-Al-Co-Ag bulk metallic glasses (BMGs) with diameters up to 20 mm were synthesized by copper mold casting. The effects of Ag alloying on the superior glass-forming ability (GFA) of Zr-Al-Co-Ag alloys were studied based on the localized atomic structure and crystallization behavior. High-energy synchrotron radiation x-ray diffraction result reveals that Ag addition in Zr-Al-Co system results in a more homogeneous local atomic structure, which could be an origin for the improved GFA of the Zr-Al-Co-Ag alloy. Crystallization products of the Zr-Al-Co-Ag glassy alloy are more complex than those of the Zr-Al-Co glassy alloy. The Zr-Al-Co-Ag BMGs free from highly toxic elements Ni and Cu exhibited a combination of superior GFA, high compressive fracture strength over 2000 MPa, low Young's modulus of 93 to 94 GPa, and good corrosion resistance in phosphate-buffered solution (PBS), inspiring their potential biomedical applications. [ABSTRACT FROM AUTHOR]

At present, metallic glasses are evaluated as alternative reinforcements for aluminum matrix composites. These composites are produced by powder metallurgy via consolidation of metallic glass-aluminum powder mixtures. In most studies, the goal has been to preserve the glassy state of the reinforcement during consolidation. However, it is also of interest to track the structure evolution of these composites when partial interaction between the matrix and the metallic glass is allowed during sintering of the mixtures. The present work was aimed to study the microstructure and mechanical properties of composites obtained by spark plasma sintering (SPS) of Al-20 vol.% Fe66Cr10Nb5B19 metallic glass mixtures and compare the materials, in which no significant interaction between the matrix and the Fe-based alloy occurred, with those featuring reaction product layers of different thicknesses. Composite materials were consolidated by SPS at 540 and 570 °C. The microstructure and mechanical properties of composites obtained by SPS and SPS followed by forging, composites with layers of interfacial reaction products of different thicknesses, and metallic glass-free sintered aluminum were comparatively analyzed to conclude on the influence of the microstructural features of the composites on their strength. [ABSTRACT FROM AUTHOR]

The appropriate design of feeders in a rigging system is critical for ensuring efficient compensation for solidification shrinkage, thus eliminating (shrinkage-related) porosity and contributing to the production of superior quality castings. In this study, a multi-objective optimisation framework combined with Computational Fluid Dynamics (CFD) simulations has been introduced to investigate the effect of the feeders' geometry on shrinkage porosity aiming to optimise casting quality and yield for a novel counter-gravity casting process (CRIMSON). The weighted sum technique was employed to convert this multi-objective optimisation problem to a single objective one. Moreover, an evolutionary multi-objective optimisation algorithm (NSGA-II) has been applied to estimate the trade-off between the objective functions and support decision makers on selecting the optimum solution based on the desired properties of the final casting product and the process characteristics. This study is one of the first attempts to combine CFD simulations with multi-objective optimisation techniques in counter-gravity casting. The obtained results indicate the benefits of applying multi-objective optimisation techniques to casting processes. [ABSTRACT FROM AUTHOR]

Using a cold graphite mold casting method, bulk AlNiY chill-zone alloys were prepared at hypereutectic compositions with Al content from 85 at.% to 94 at.%. It was found that ultra-hard surface layers with a thickness of about 200 µm and submicron grain size form when the melt can be undercooled without heterogeneous nucleation at the mold contact surface. This hard chill-zone forming in contact with the mold possesses Vickers microhardness Hv about 350-420 and is thus harder than fully amorphous Al alloys. In compression, ultimate strength more than 1.1 GPa and true strain more than 150% without failure were achieved simultaneously. The combination of high strength and good plasticity will be discussed in relation to the special structure of the chill-zone alloy. [ABSTRACT FROM AUTHOR]