Search

Os taninos são compostos naturais que têm a propriedade de complexarem com as proteínas formando agregados insolúveis em solução. A interação destes compostos com as proteínas salivares leva à sensação de adstringência de alguns frutos (especialmente se pouco maduros) e bebidas como o vinho tinto e o chá. No presente estudo pretende-se verificar de que forma a concentração de protéina e tanino, as suas estruturas, hidratos de carbono e ainda a força iónica, podem influênciar a formação de complexos tanino-proteina. Verificou-se que menores concentrações de proteína no meio vão provocar um aumento da adstringência. A estrutura da proteína também irá influência a formação de complexos tanino-proteína, o aumento da força iónica irá provocar uma diminuição da formação de complexos tanino-proteína, hidratos de carbono com uma estrutura não capsolante em elevadas concentrações irão provocar uma aumento da adstringência, ao contrário de hidratos de carbono com uma estrutura capsolante. Influence of protein concentration, ionic strength and type of carbon hydrate in training complex tannin-protein Abstract: The tannins are natural compounds which have the property of complexing with proteins form insoluble aggregates in solution. The interaction of these compounds with salivary proteins leads to the sensation of astringency of some fruits (especially if unripe) and drinks such as red wine and tea. The present study intends to check how the concentration of protein and tannin, their structures, carbohydrate and ionic strength also may influence the formation of tannin-protein complexes. It was found that lower protein concentrations in the medium will cause an increase in astringency. The protein structure will also influence the formation of tannin-protein complexes. Increasing the ionic strength will cause a reduction in the formation of tannin-protein complexes. Carbohydrates with a structure not capsolante in high concentrations will cause an increase in astringency, unlike carbohydrates with a capsolante structure.

Strategies for obtaining deep slots in soft materials can vary significantly. Conventionally, the tool travels along the slot, removing material mainly with the side cutting edges. However, a “plunge milling” strategy is also possible, performing the cut vertically, taking advantage of the tip cutting edges that almost reach the center of the tool. Although both strategies are already commonly used, there is a clear gap in the literature in studies that compare tool wear, surface roughness, and productivity in each case. This paper describes an experimental study comparing the milling of deep slots in AA7050-T7451 aluminum alloy, coated with a novel DLCSiO500W3.5O2 layer to minimize the aluminum adhesion to the tool, using conventional and plunge milling strategies. The main novelty of this paper is to present a broad study regarding different factors involved in machining operations and comparing two distinct strategies using a novel tool coating in the milling of aeronautical aluminum alloy. Tool wear is correlated with the vibrations of the tools in each situation, the cycle time is compared between the cases studied, and the surface roughness of the machined surfaces is analyzed. This study concludes that the cycle time of plunge milling can be about 20% less than that of conventional milling procedures, favoring economic sustainability and modifying the wear observed on the tools. Plunge milling can increase productivity, does not increase tool tip wear, and avoids damaging the side edges of the tool, which can eventually be used for final finishing operations. Therefore, it can be said that the plunge milling strategy improves economic and environmental sustainability as it uses all the cutting edges of the tools in a more balanced way, with less global wear.

Plastics injection molding is a sector that is becoming increasingly competitive due to the environmental issues it entails, pressuring consumers to reduce its use. Thus, plastics processing companies attempt to minimize costs, with the aim of increasing competitiveness. This pressure is transmitted to the mold manufacturers, as the mold conditions the equipment that it is used for, which may have significantly different amortization costs. The present work aimed to design a novel mechanism able to deal with the necessary movements in 2K injection molding in a more compact way. A novel hybrid mechanical and hydraulic movement was developed. More compact movements lead to smaller molds, which can be used on smaller injection machines, leading to reduced costs. This methodology consists of multiplying a disproportionate movement to the mold through several movements, which results in a slightly more complex, but much more compact, system for molds devoted to multi-material injected parts.

Machining processes remain an unavoidable technique in the production of high-precision parts. Tool behavior is of the utmost importance in machining productivity and costs. Tool performance can be assessed by the roughness left on the machined surfaces, as well as of the forces developed during the process. There are various techniques to determine these cutting forces, such as cutting force prediction or measurement, using dynamometers and other sensor systems. This technique has often been used by numerous researchers in this area. This paper aims to give a review of the different techniques and devices for measuring the forces developed for machining processes, allowing a quick perception of the advantages and limitations of each technique, through the literature research carried out, using recently published works.

Turning continues to be the largest segment of the machining industry, which highlights the continued demand for turned parts and the overall improvement of the process. The turning process has seen quite an evolution, from basic lathes using solid tools, to complex CNC (Computer Numerical Control) multi-process machines, using, for the most part, coated inserts and coated tools. These coatings have proven to be a significant step in the production of high-quality parts and a higher tool life that have captivated the industry. Continuous improvement to turning coated tools has been made, with many researches focusing on the optimization of turning processes that use coated tools. In the present paper, a presentation of various recently published papers on this subject is going to be made, mentioning the various types of coatings that have recently been used in the turning process, the turning of hard to machine materials, such as titanium alloys and Inconel, as well as the interaction of these coatings with the turned surfaces, the wear patterns that these coatings suffer during the turning of materials and relating these wear mechanisms to the coated tool’s life expectancy. Some lubrication conditions present a more sustainable alternative to current methods used in the turning process; the employment of coated tool inserts under these conditions is a current popular research topic, as there is a focus on opting for more eco-friendly machining options.

Following more than a century of cocaine hydrochloride extraction from Erythroxylon coca, this drug remains representing a serious social and public health problema around the world. This paper intends to provide a review about the cocaine theme, focusing on historical background and on its different neurotransmission systems, as well as addresses therapeutics aspects about drug addiction.Electronic search in databases Medline, Pubmed and Lilacs was accomplished in order to select classics and recent studies relevant to the discussion of issue addressed.Previous studies have shown high vulnerability to relapse to cocaine seeking following prolonged withdrawal periods. Such behavioral consequences have been cre-dited to induced changes in brain neurotransmitters provoked by repeated cocaine use. In recent years, the growing abuse of this drug has mobilized researchers worldwide in seeking for new therapies that reduce the behavioral and neurochemical changes resulting from addiction.Numerous advances regarding the treatment of cocaine abuse and dependence have emerged in recent years. However, researche aiming at a safe and effective users' pharmacological treatment remain necessary and should be continued.

The results of the first 9 patients with proctocolectomy and ileal pouch operated on between 1983 and 1990 were analysed. This procedure was carried out in 8 patients with adenomatous polyposis. Three of these patients had an associated rectal cancer and one a degenerated sigmoid polyp. One patient had ulcerative colitis and was previously submitted to a colectomy related with perforated fulminant colitis. Three types of pouches were constructed: 3 S, 3 J and 3W, all with a temporary ileostomy. A circular stapler was used in 2 cases for ileoanal anastomosis. Three postoperative complications were observed: two patients with pouchitis during the presence of a diverting ileostomy and an ileal fistula following ileostomy closure, all medically treated. Clinical and functional results were evaluated 1 to 7 years after the procedure. The average daytime stool frequency was 4 with 1 nocturnal. All patients indicated normal continence. One patient had her professional life affected due to the increased number of defecations. Differences in the clinical results of the patients with S, J and W pouches were not statistically different. The functional results expressed as median and range were as follows: resting and pressure 45 cm H2O (20-60), voluntary anal pressure 70 cm H2O (34-120), compliance 3.70 ml/cm H2O (1.14-11.40), maximal tolerated volume (MTV) 320 ml (110-48) and threshold volume 95 ml (40-170). The MTV values of the groups with J and W pouches were 190 ml (180-200) and 370 ml (340-480), respectively (p = 0.05).(ABSTRACT TRUNCATED AT 250 WORDS)

Since there is a hypothesis that qualitative and/or quantitative differences of specific proteins may be associated with morphological variants in cacti of the Cereus genus (phenotypes erect, tortuosus and monstruosus), in current study we tested three different methods for protein extraction from shoots of the phenotypic variants to obtain protein fractions for further proteomic analysis. The TCA/acetone method for protein extraction revealed a larger number of welldefined bands in SDSPAGE system than the methods with phenol. The quantification of protein extracted by TCA/acetone ranged between 0.488 (tortuosus) and 2.92 µg·mL-1 (monstruosus). Although the use of phenol is the most appropriate procedure for protein extraction from recalcitrant tissues, results have shown that extraction buffer containing two antioxidant agents (EDTA and ßmercaptoethanol) and PMSF to prevent protein degradation was efficient to avoid proteolysis and lower protein yield, than using TCA/acetone precipitation for protein extraction from shoots of Cereus sp. The use of extraction buffer with appropriate combinations of antioxidant agents, phenolcomplexing agents, and protease inhibitors may be an efficient alternative for proteins extraction from succulent and recalcitrant tissues (such as cactus plants) using a simple protein extraction method. [ABSTRACT FROM AUTHOR]

A solution to the equivalence problem in three-dimensional gravity is given and a practically useful method to obtain a coordinate invariant description of local geometry is presented. The method is a nontrivial adaptation of the Karlhede invariant classification of spacetimes of general relativity. The local geometry is completely determined by the curvature tensor and a finite number of its covariant derivatives in a frame where the components of the metric are constants. The results are presented in the framework of real two-component spinors in three-dimensional spacetimes, where the algebraic classifications of the Ricci and Cotton-York spinors are given and their isotropy groups and canonical forms are determined. As an application we discuss Gödel-type spacetimes in three-dimensional general relativity. The conditions for local space and time homogeneity are derived and the equivalence of three-dimensional Gödel-type spacetimes is studied and the results compared with previous work on four-dimensional Gödel-type spacetimes. [ABSTRACT FROM AUTHOR]

Although additive manufacturing is gaining prominence in the market, many applications require very high levels of precision, which are currently not attainable by additive manufacturing [...]

Inconel 718 is a highly valued material in the aerospace and nuclear industries due to the fact of its exceptional properties. However, the processing of this material is quite difficult, especially through machining processes. Machining this material results in rapid tool wear, even when low material removal rates are considered. In this study, instrumented turning experiments were employed to evaluate the machinability of Inconel 718 alloy using PCBN tools while assessing the usage of two distinct binder phases, TiN and TiC, for those cutting tools. It was found that the tool life was highly sensitive to the cutting speeds but also affected by the workpiece mechanical properties. At lower cutting speeds, notch wear significantly impacted the tool integrity, whereas at higher cutting speeds, flank wear was the primary failure mode of the tool. The flank wear of the tools with TiN-based binder outperformed TiC by almost 30%, presenting a more consistent behavior when machining.

Due to Inconel 718’s high mechanical properties, even at higher temperatures, tendency to work-harden, and low thermal conductivity, this alloy is considered hard to machine. The machining of this alloy causes high amounts of tool wear, leading to its premature failure. There seems to be a gap in the literature, particularly regarding milling and finishing operations applied to Inconel 718 parts. In the present study, the wear behavior of multilayered PVD HiPIMS (High-power impulse magnetron sputtering)-coated TiN/TiAlN end-mills used for finishing operations on Inconel 718 is evaluated, aiming to establish/expand the understanding of the wear behavior of coated tools when machining these alloys. Different machining parameters, such as cutting speed, cutting length, and feed per tooth, are tested, evaluating the influence of these parameters’ variations on tool wear. The sustained wear was evaluated using SEM (Scanning electron microscope) analysis, characterizing the tools’ wear and identifying the predominant wear mechanisms. The machined surface was also evaluated after each machining test, establishing a relationship between the tools’ wear and production quality. It was noticed that the feed rate parameter exerted the most influence on the tools’ production quality, while the cutting speed mostly impacted the tools’ wear. The main wear mechanisms identified were abrasion, material adhesion, cratering, and adhesive wear. The findings of this study might prove useful for future research conducted on this topic, either optimization studies or studies on the simulation of the milling of Inconel alloys, such as the one presented here.

Many municipal facilities, such as pools and drinking water treatment facilities, are subject to ongoing maintenance due to the corrosion of their metallic materials caused by chlorine, leading to high costs and a possible risk to public health. A proper study of the employed product’s effect could lead to the use of better materials, which significantly increase the lifetime of metallic equipment more attacked by corrosion, through studies evaluating their cost-effectiveness. This paper was carried out with the objective of studying the degradation of some metallic materials (AISI 316L, AISI 321 and Duplex 14462) used in the referred facilities in order to select the one that possessed a better behavior. It was observed that the introduction of some more adequate materials can drastically reduce maintenance operations, with Duplex 14462 showing the best results, ideal for greater chlorine concentrations, followed by AISI 321, which may be employed for components in less contact with chlorine, since it is more easily affordable.

Nickel-based superalloys, namely INCONEL® variants, have had an increase in applications throughout various industries like aeronautics, automotive and energy power plants. These superalloys can withstand high-temperature applications without suffering from creep, making them extremely appealing and suitable for manufactured goods such as jet engines or steam turbines. Nevertheless, INCONEL® alloys are considered difficult-to-cut materials, not only due to their superior material properties but also because of their poor thermal conductivity (k) and severe work hardening, which may lead to premature tool wear (TW) and poor final product finishing. In this regard, it is of paramount importance to optimise the machining parameters, to strengthen the process performance outcomes concerning the quality and cost of the product. The present review aims to systematically summarize and analyse the progress taken within the field of INCONEL® machining sensitively over the past five years, with some exceptions, and present the most recent solutions found in the industry, as well as the prospects from researchers. To accomplish this article, ScienceDirect, Springer, Taylor & Francis, Wiley and ASME have been used as sources of information as a result of great fidelity knowledge. Books from Woodhead Publishing Series, CRC Press and Academic Press have been also used. The main keywords used in searching information were: “Nickel-based superalloys”, “INCONEL® 718”, “INCONEL® 625” “INCONEL® Machining processes” and “Tool-wear mechanisms”. The combined use of these keywords was crucial to filter the huge information currently available about the evolution of INCONEL® machining technologies. As a main contribution to this work, three SWOT analyses are provided on information that is dispersed in several articles. It was found that significant progress in the traditional cutting tool technologies has been made, nonetheless, the machining of INCONEL® 718 and 625 is still considered a great challenge due to the intrinsic characteristics of those Ni-based-superalloys, whose machining promotes high-wear to the tools and coatings used.

Due to the automotive industry’s strict demands, customers submit constant production pressure, leading to the adoption of new methodologies, techniques, and management ideas. The goal is always to minimise losses and waste. These demands also affect the maintenance department, which has to keep the balance between machines’ availability for production and ensuring that the machines’ proper running conditions translate into excellent-quality products. Thus, continuous improvement and correct management of maintenance activities are crucial for a company to maintain effective production, without defects, breakdowns, and accidents. Nevertheless, some maintenance activities should also prevent the degradation of equipment conditions in order to produce high-quality products. This paper presents an improvement of maintenance activities conducted on equipment that produces large tires. The main problems and technical difficulties of Machine Tolerance Check (MTC) activities are explored by analysing existing documents, internal knowledge, and changes to working methods. We discuss the implementation of the SMED (Single-Minute Exchange of Die) methodology in calibration procedures, as this method is commonly applied to machines’ setups to reduce downtime. At the end of the study, a 31% decrease in the duration of machine tolerance check activities was achieved, which led to a significant increase in the equipment’s availability.

Additive manufacturing is defined as a process based on the superposition of layers of materials in order to obtain 3D parts; however, the process does not allow achieve the adequate and necessary surface finishing. In addition, with the development of new materials with superior properties, some of them acquire high hardness and strength, consequently decreasing their ability to be machined. To overcome this shortcoming, a new technology assembling additive and subtractive processes, was developed and implemented. In this process, the additive methods are integrated into a single machine with subtractive processes, often called hybrid manufacturing. The additive manufacturing process is used to produce the part with high efficiency and flexibility, whilst machining is then triggered to give a good surface finishing and dimensional accuracy. With this, and without the need to transport the part from one machine to another, the manufacturing time of the part is reduced, as well as the production costs, since the waste of material is minimized, with the additive–subtractive integration. This work aimed to carry out an extensive literature review regarding additive manufacturing methods, such as binder blasting, directed energy deposition, material extrusion, material jetting, powder bed fusion, sheet laminating and vat polymerization, as well as machining processes, studying the additive-subtractive integration, in order to analyze recent developments in this area, the techniques used, and the results obtained. To perform this review, ScienceDirect, Web of Knowledge and Google Scholar were used as the main source of information because they are powerful search engines in science information. Specialized books have been also used, as well as several websites. The main keywords used in searching information were: “CNC machining”, “hybrid machining”, “hybrid manufacturing”, “additive manufacturing”, “high-speed machining” and “post-processing”. The conjunction of these keywords was crucial to filter the huge information currently available about additive manufacturing. The search was mainly focused on publications of the current century. The work intends to provide structured information on the research carried out about each one of the two considered processes (additive manufacturing and machining), and on how these developments can be taken into consideration in studies about hybrid machining, helping researchers to increase their knowledge in this field in a faster way. An outlook about the integration of these processes is also performed. Additionally, a SWOT analysis is also provided for additive manufacturing, machining and hybrid manufacturing processes, observing the aspects inherent to these technologies.

One of the most critical factors in producing plastic injection molds is the cost estimation of machining services, which significantly affects the final mold price. These services’ costs are determined according to the machining time, which is usually a long and expensive operation. If it is considered that the injection mold parts are all different, it can be understood that the correct and quick estimation of machining times is of great importance for a company’s success. This article presents a proposal to apply artificial neural networks in machining time estimation for standard injection mold parts. For this purpose, a large set of parts was considered to shape the artificial intelligence model, and machining times were calculated to collect enough data for training the neural networks. The influences of the network architecture, input data, and the variables used in the network’s training were studied to find the neural network with greatest prediction accuracy. The application of neural networks in this work proved to be a quick and efficient way to predict cutting times with a percent error of 2.52% in the best case. The present work can strongly contribute to the research in this and similar sectors, as recent research does not usually focus on the direct prediction of machining times relating to overall production cost. This tool can be used in a quick and efficient manner to obtain information on the total machining cost of mold parts, with the possibility of being applied to other industry sectors.

Wire rope manufacturing is an old industry that maintains its place in the market due to the need for products with specific characteristics in different sectors. The necessity for modernization and performance improvement in this industry, where there is still a high amount of labor dedicated to internal logistics operations, led to the development of a new technology method, to overcome uncertainties related to human behaviour and fatigue. The removal of successive yarn coils from a twisting and winding machine, as well as cutting the yarn and connecting the other end to the shaft in order to proceed with the process, constitutes the main problem. As such, a mobile automatic system was created for this process, due to its automation potential, with a project considering the design of a 3D model. This novel robotic manipulator increased the useful production time and decreased the winding coil removal cycle time, resulting in a more competitive, fully automated product with the same quality. This system has led to better productivity and reliability of the manufacturing process, eliminating manual labor and its cost, as in previously developed works in other industries.

Currently, there is a lack of affordable and simple tools for the estimation of these costs, especially for machining operations. This is particularly true for manufacturing SMEs, in which the cost estimation of machined parts is usually performed based only on required material for part production, or involves a time-consuming, non-standardized technical analysis. Therefore, a cost estimation tool was developed, based on the calculated machining times and amount of required material, based on the final drawing of the requested workpiece. The tool was developed primarily for milling machines, considering milling, drilling, and boring/threading operations. Regarding the considered materials, these were primarily aluminum alloys. However, some polymer materials were also considered. The tool first estimates the required time for total part production and then calculates the total cost. The total production time is estimated based on the required machining operations, as well as drawing, programming, and machine setup time. A part complexity level was also introduced, based on the number of details and operations required for each workpiece, which will inflate the estimated times. The estimation tool was tested in a company setting, comparing the estimated operation time values with the real ones, for a wide variety of parts of differing complexity. An average error of 14% for machining operation times was registered, which is quite satisfactory, as this time is the most impactful in terms of machining cost. However, there are still some problems regarding the accuracy in estimating finishing operation times.

Due to their high mechanical property values and corrosion resistance, duplex stainless steels (DSSs) are used for a wide variety of industrial applications. DSSs are also selected for applications that require, especially, high corrosion resistance and overall good mechanical properties, such as in the naval and oil-gas exploration industries. The obtention of components made from these materials is quite problematic, as DSSs are considered difficult-to-machine alloys. In this work, the developed wear during milling of the UNS S32101 DSS alloy is presented, employing four types of milling tools with different geometries and coatings. The influence of feed rate and cutting length variations on the tools’ wear and their performance was evaluated. The used tools had two and four flutes with different coatings: TiAlN, TiAlSiN and AlCrN. The cutting behavior of these tools was analyzed by collecting data regarding the cutting forces developed during machining and evaluating the machined surface quality for each tool. After testing, the tools were submitted to SEM analysis, enabling the identification of the wear mechanisms and quantification of flank wear, as well as identifying the early stages of the development of these mechanisms. A comparison of all the tested tools was made, determining that the TiAlSiN-coated tools produced highly satisfactory results, especially in terms of sustained flank wear.

Duplex stainless steels are being used on applications that require high corrosion resistance and excellent mechanical properties, such as the naval and oil-gas exploration industry. The components employed in these industries are usually obtained by machining; however, these alloys have low machinability when compared to conventional stainless steels, usually requiring the employment of tool coatings. In the present work, a comparative study of TiAlSiN coating performance obtained by these two techniques in the milling of duplex stainless-steel alloy LDX 2101 was carried out. These coatings were obtained by the conventional direct current magnetron sputtering (dc MS) and the novel high power impulse magnetron sputtering (HiPIMS). The coatings were analyzed and characterized, determining mechanical properties for both coatings, registering slightly higher mechanical properties for the HiPIMS-obtained coating. Machining tests were performed with varying cutting length and feed-rate, while maintaining constant values for axial and radial depth of cut and cutting speed. The surface roughness of the material after machining was assessed, as well as the wear sustained by each of the tool types, identifying the wear mechanisms and behavior of these tools, as well as registering the flank wear values presented for each of the tested tools. The HiPIMS-obtained coating exhibited a very similar behavior when compared to the other, producing similar surface roughness quality. However, the HiPIMS coating exhibited less wear for higher cutting lengths, proving to be a better choice in this case, especially regarding tool life.

Copper-Beryllium alloys have excellent wear resistance and high mechanical properties, they also possess good electrical and thermal conductivity, making these alloys very popular in a wide variety of industries, such as aerospace, in the fabrication of tools for hazardous environments and to produce injection molds and mold inserts. However, there are some problems in the processing of these alloys, particularly when these are subject to machining processes, causing tools to deteriorate quite rapidly, due to material adhesion to the tool’s surface, caused by the material’s ductile nature. An assessment of tool-wear after machining Cu-Be alloy AMPCOLOY 83 using coated and uncoated tools was performed, offering a comparison of the machining performance and wear behavior of solid-carbide uncoated and DLC/CrN multilayered coated end-mills with the same geometry. Multiple machining tests were conducted, varying the values for feed and cutting length. In the initial tests, cutting force values were registered. The material’s surface roughness was also evaluated and the cutting tools’ edges were subsequently analyzed, identifying the main wear mechanisms and how these developed during machining. The coated tools exhibited a better performance for shorter cutting lengths, producing a lower degree of roughness on the surface on the machined material. The wear registered for these tools was less intense than that of uncoated tools, which suffered more adhesive and abrasive damage. However, it was observed that, for greater cutting lengths, the uncoated tool performed better in terms of surface roughness and sustained wear.

The structure of car seats is becoming increasingly complex, with mixing of wire conformation and plastic injection. The plastic over-molding process implies some labor, which can be reduced if novel solutions are applied in this manufacturing area. The handling of the wires used in car seats is the main problem identified in the process, wasting time both in the feeding and in the extraction of the molds used in the wire over-molding process. However, these machines are usually extremely compact and the free space around them is too short. In classic molding injection machines, there are just two half-molds, the female, and the male. In the over-molding process of wires used in car seats, three half-molds are used in order to increase the cycle time. Thus, to solve this problem, the classic robotic solutions are not appliable due to lack of space and elevated cost. This work describes the development of an automated solution able to handle the wires in both the feeding and the extracting phases of the production cycle, avoiding the traditional labor costs associated with this type of machine. Departing from an industrial need, the developed novel solution is described in detail and can be successfully adapted to other situations of low added-value products where it is needed to increase the productivity and competitiveness of the product. The system developed uses mechanical and pneumatic solutions which, combined, can be used to solve the identified problem, occupying a restricted space and requiring a small budget. This solution can be translated into guidelines that will allow the analysis of situations where the same system can be applied.

Grade P91 is a relatively new class of steel, which has received special attention from designers because it presents extremely interesting characteristics for specific applications. This steel exhibits ideal properties for demanding applications, especially involving high temperature and pressure, being employed in facilities such as power plants and other equipment, such as heat exchangers. P91 welds usually need heat treatments, which are already parameterized in the codes. However, standardized treatments are time-consuming and harmful to the environment, as they massively consume energy. Some attempts have been made in the past to reduce the time and energy spent on these treatments. This work aims to extend this study, now presenting better solutions than those obtained previously. This work presents four new conditions for the heat treatment of joints carried out on P91 steel, with a view to reducing processing time, reducing energy consumption, and an even better balance between mechanical strength and elongation after failure. Heat treatment conditions were established in which there was a loss of about 14% in Ultimate Tensile Strength (UTS), but in which a gain of about 50% in elongation was obtained, compared to welding without any treatment, but also with 10% losses in the UTS and 30% gains in elongation when compared to the solution recommended as more correct in the codes, saving a lot of time and energy in the treatment process. Thus, these solutions may be adopted in the future with gains in terms of productivity and economic and environmental sustainability.

The machining process is still a very relevant process in today’s industry, being used to produce high quality parts for multiple industry sectors. The machining processes are heavily researched, with the focus on the improvement of these processes. One of these process improvements was the creation and implementation of tool coatings in various machining operations. These coatings improved overall process productivity and tool-life, with new coatings being developed for various machining applications. TiAlN coatings are still very present in today’s industry, being used due to its incredible wear behavior at high machining speeds, high mechanical properties, having a high-thermal stability and high corrosion resistance even at high machining temperatures. Novel TiAlN-based coatings doped with Ru, Mo and Ta are currently under investigation, as they show tremendous potential in terms of mechanical properties and wear behavior improvement. With the improvement of deposition technology, recent research seems to focus primarily on the study of nanolayered and nanocomposite TiAlN-based coatings, as the thinner layers improve drastically these coating’s beneficial properties for machining applications. In this review, the recent developments of TiAlN-based coatings are going to be presented, analyzed and their mechanical properties and cutting behavior for the turning and milling processes are compared.