Search

We have noted that, due to an unfortunate copy/paste error in the preparation of Table S3 (Supporting Information, SI), some data in the same Table S3 and in Figures 1c and 2 (left) are incorrect. Amended versions of Table S3, Figure 1, and Figure 2 are provided here. We underline that the above did not affect the results, discussion, and conclusions of the paper because the error was only cosmetic and limited to those two figures, whereas correct data were used throughout. (Table Presented) (Figure Presented).

Book of Abstracts-P60

Book of Abstracts -P09 G

Studies on the effects of hydrogen, monomer concentration and temperature in propene polymerization using high-activity MgCl2-supported catalysts have revealed that the effects of the catalyst on polymer yield, isotacticity and molecular weight are interrelated and dependent on both regio- and stereoselectivity. The high hydrogen sensitivity of catalysts containing a diether donor is mainly due to chain transfer following the occasional regioirregular (2,1-) monomer insertion. The probability of regio- and stereoirregular insertion decreases with monomer concentration, indicating the presence of nonsymmetric active centres. The stereoregularity of the isotactic polymer also increases with polymerization temperature, indicating a greater relative increase in productivity for highly isospecific as opposed to moderately isospecific centres.

The performance of a second-generation "violet" TiCl3-based catalyst in propene polymerization is compared with that of first-generation TiCl3's and of supported MgCl2/TiCl4 "high-yield" systems. The results suggest that a few "adjustments" may be needed in the current views on the nature of the active species in such systems.

The stereosequence distribution of the "atactic" and "isotactic" fractions of a polypropylene sample made with a MgCl2-supported catalyst was determined by means of high-resolution C-13 NMR and analyzed in terms of statistical models of increasing sophistication. Two-site models, including the one normally used for the interpretation of "routine" C-13 NMR data at pentad level, were shown to be inconsistent with the much finer high-resolution data. A good agreement between experimental and calculated distributions could be obtained only in terms of a three-site model, describing each fraction as a mixture of highly isotactic, weakly isotactic ("isotactoid") and syndiotactic sequences. According to such model, the two fractions comprise the same three building blocks (the configuration of the three different types of stereosequences being almost invariant) and differ merely in their relative amounts (which indicates a stereoblock nature). The correlations with the physical properties of the materials and the implications on the nature of the catalytic species are also briefly discussed.

45 years after the discovery of transition metals and organometallics as cocatalysts for the polymerization of olefins and for organic synthesis, these compounds have not lost their fascination. The birthday of Karl Ziegler, the great pioneer in this metalorganic catalysis, is now 100 years ago. Polyolefins and polydienes produced by Ziegler-Natta catalysis are the most important plastics and elastomers. New impulses for the polymerization of olefins have been brought about by highly active metallocenes and other single site catalysts. Just by changing the ligands of the organometallic compounds, the structure of the polymers produced can be tailored in a wide manner. In invited lectures and posters, relevant aspects of the metalorganic catalysts for synthesis and polymerization are discussed in this book. This includes mechanism and kinetics, stereochemistry, material properties, and industrial applications

POLY-001

"Classical" MgCl2-supported Ziegler-Natta Catalysts (ZNC) continue to monopolize the industrial prodn. of isotactic polypropylene. There is a growing awareness of the inherent competitive edge of these low-cost systems over single-center ones (primarily metallocenes), and of the potential for further improvement, particularly if a deeper insight into the structure of the catalytic surfaces and the mechanisms of their modification by means of electron donors can be achieved. In the framework of a project ultimately aiming at the implementation of ZNC with known and controlled surface structure, we started a re-visitation of the whole area by using High Resoln. Magic Angle Spinning 1H NMR. In this paper, we report on the results obtained for the neat MgCl2 matrix and for model MgCl2/electron donor adducts, which yield information on the relative stability of the lateral surfaces of the MgCl2 crystallites, and on the dynamic features of donor chemisorption as a function of donor nature and extent of surface coordinative unsatn. In our opinion, this exptl. approach opens new possibilities in the investigation of these complicated and challenging catalyst systems.

The solution structure and dynamics of three prototypical bis-indenyl ansa-zirconocenium methyl cations (Me2Si(2-methyl-4-phenyl-6-tert-butylindenyl)2ZrMe+, [1Me]+ Me2Si(2,4-dimethylindenyl)2ZrMe+, [2Me]+ Me2Si(indenyl)2ZrMe+, [3Me]+) paired with the weakly coordinating B(C6F5)4- anion have been investigated by NMR spectroscopy in aromatic hydrocarbons with different polarities (toluene, ϵr = 2.38; chlorobenzene, ϵr = 5.69; 1,2-difluorobenzene (ODFB), ϵr = 13.38). These highly electrophilic cations are stabilized by solvent coordination, as evidenced by the unequivocal identification of [1Me·C7H8]+B(C6F5)4-, a rare example of a toluene-stabilized ion pair that has been fully characterized in solution. Combining spectroscopic and DFT methods allowed us to evaluate how solvent coordination modulates the dynamic processes typical of this class of catalysts. An exchange between the two faces of coordinated toluene (face inversion, FI) occurs without solvent decomplexation (ΔH⧧FI = 14.6 kcal mol-1 ΔS⧧FI = 3 cal mol-1 K-1 ΔG⧧FI(298) = 13.7 kcal mol-1) and is about 20 times faster than the exchange between coordinated and free solvent (solvent decomplexation, SD, ΔH⧧SD = 17.9 kcal mol-1 ΔS⧧SD = 10 cal mol-1 K-1 ΔG⧧SD(298) = 14.9 kcal mol-1) and ion pair symmetrization (IPS, ΔH⧧IPS = 18.6 kcal mol-1 ΔS⧧IPS = 12 cal mol-1 K-1 ΔG⧧IPS(298) = 14.9 kcal mol-1). For the ion pairs [1-3Me·solvent]+B(C6F5)4-, IPS rate constants (kIPS) do not correlate with the solvent polarity (kIPS(ODFB) > kIPS(toluene) > kIPS(chlorobenzene)). For the more coordinating toluene and chlorobenzene solvents, ΔG⧧IPS nicely tracks with the amount of positive charge at the metal, increasing as the positive charge increases (qZrMe2,CM5; 1Me2 > 3Me2 > 2Me2). In contrast, in the less coordinating ODFB, differences in the IPS barriers for [1-3Me·ODFB]+B(C6F5)4- appear to correlate better with steric parameters, as measured by the percent buried volume on the open quadrants (%VBur,open) for the corresponding neutral precursors (%VBur,open = 34.8, 35.5, 34.6% for 1Me2, 2Me2, and 3Me2, respectively).

The performance of C2-symmetric ansa-hafnocene catalysts for isotactic polypropylene typically deteriorates at increasing temperature much faster than that of their zirconium analogues. Herein, we analyze in detail a set of five Hf/Zr metallocene pairs—including some of the latest generation catalysts—at medium- to high-polymerization temperature. Quantitative structure–activity relationship (QSAR) models for stereoselectivity, the ratio allyl/vinyl chain ends, and 2,1/3,1 misinsertions in the polymer indicate a strong dependence of polymerization performance on electrophilicity of the catalyst, which is a function of the ligand framework and the metal center. Based on this insight, the stronger performance decline of hafnocenes is ascribed to electrophilicity-dependent stabilization effects.

Absolute rigidity is rare in the "soft" world of organometallics. Here we introduce two cyclopenta[a]triptycyl ansa-zirconocene catalysts for isotactic-selective propene polymerization, designed by means of an integrated high-throughput experimentation/quantitative structure-activity relationship modeling approach. An ultrarigid ligand precisely wrapped around the Zr center enforces an enzyme-like lock and key fit, effectively hampering undesired reactive events, even at high temperature. Stereodefective units are hardly detectable by 13C NMR in the polymer produced at 120 °C; this corresponds to an enantioselectivity exceeding 6-7 kcal/mol: i.e., less than 1 propene misinsertion every 4000 (and at room temperature, one every ∼40000!).

“Structural” AlMe2(bht) was found to be an integral building block of the “TMA-free” olefin polymerization cocatalyst MAO/BHT (TMA = trimethylaluminum, MAO = methylaluminoxane, BHT = 2,6-di-tert-butyl-4-methylphenol). NMR studies show that treatment of MAO/BHT with the neutral N-donor pyridine (py) leads to selective generation of neutral AlMe2(bht)(py). The reaction of MAO/BHT with 2,2'-bipyridine (bipy) generates cationic [AlMe(bht)(bipy)]+ fragments (bht = BHT phenolate), analogously to what happens when unmodified MAO is treated with bipy, causing [AlMe2(bipy)]+ formation. This suggests that the activation of an olefin polymerization precatalyst LnMX2 (X = Me or Cl) can occur via an indirect pathway involving [AlMeR]+ (R = Me or bht) transient species (rather than direct Cl/Me abstraction by the Al-cages) not only when unmodified MAO is exploited but also in the case of “TMA-free” BHT-modified MAO. The high chemoselectivity of py for neutral Al adducts however presents a distinct difference to unmodified MAO. These observations indicate that a) “structural” TMA is converted into “structural” AlMe2(bht) upon reaction of MAO with BHT and that b) MAO/BHT is harder to ionize than unmodified MAO. A refined formula and cluster size estimation [(AlOMe)0.87(AlMe2bht)0.13]n (n = 57–84) is proposed for MAO/BHT based on this new experimental evidence, accounting for the presence of “structural” AlMe2(bht) units.

Highly active molecular catalysts for olefin polymerization are extremely difficult to run in high-throughput experimentation (HTE) platforms. With common activators like methylaluminoxane (MAO) or a combination of tri-iso-butylaluminum and trityl tetrakis(perfluorophenyl)borate (TIBA/TTB), the necessary downscaling ends up with (sub)nanomole precatalyst loadings and poorly reproducible results due to the presence of adventitious impurities in similar amounts. Unexpectedly, we have now discovered that a convenient solution to this problem is provided by TIBA/AB (AB = N,N-dimethylanilinium tetrakis(perfluorophenyl)borate), a long-known but relatively uncommon protic activator. Indeed, with a proper operating protocol, a tunable precatalyst activation delay (minutes to hours) can be achieved, and even at high (≥10 nmol) catalyst loadings, a transient phase of well-controlled activity can be maintained long enough to produce the polymer amounts necessary for the characterizations under highly reproducible conditions. Importantly, polymer properties were not affected by choice of the activator, provided that the polymerization was kinetically controlled, which makes TIBA/AB the best option for HTE screenings of industrially relevant catalysts.

The crystalline morphology of ethylene/1-octene (EO-BC) statistical multiblock copolymers is investigated by transmission electron microscopy (TEM). EO-BCs are an important class of thermoplastic elastomers characterized by alternating crystalline, octene-poor, hard blocks and amorphous, octene-rich, soft blocks and statistical distribution of block length (BL) and number of blocks/chain (NB). Adopting similar crystallization conditions, samples with only subtle differences in the chain microstructure, are shown to display different solid-state morphology as probed by TEM and different melt rheology. In particular, the homogeneous or heterogeneous lamellar morphology which develops in the solid state reflects the tendency of the samples to show homogeneous or heterogeneous melt-rheology, respectively. As EO-BCs are a reactor blend of non-uniform chains, it is argued that the solid state and melt phase behavior of EO-BCs is controlled by differences in the relative abundance of chains including a prevalence of hard blocks of short and/or high length.

New ansa-zirconocene with bis(inden-2-yloxy)dimethylsilane ligand was synthesized and characterized by NMR spectroscopy and X-ray crystallography. The zirconocene was found to be highly active catalyst of ethylene polymerization and ethylene/hex-1-ene copolymerization upon methylaluminoxane activation.

The established model cluster (AlOMe)16(AlMe3)6 for methylaluminoxane (MAO) cocatalyst has been studied by density functional theory, aiming to rationalize the different behaviors of unmodified MAO and TMA-depleted MAO/BHT (TMA = trimethylaluminum; BHT = 2,6-di-tert-butyl-4-methylphenol), highlighted in previous experimental studies. The tendency of the three model Lewis acidic sites A–C to release neutral Al fragments (i.e., AlMe2R; R = Me or bht) or transient aluminum cations (i.e., [AlMeR]+) has been investigated both in the absence and in the presence of neutral N-donors. Sites C are most likely responsible for the activation capabilities of TMA-rich MAO, but TMA depletion destabilizes them, possibly inducing structural rearrangements. The remaining sites A and B, albeit of lower Lewis acidity, should be still able to release cationic Al fragments when TMA-depleted modified MAOs are treated with N-donors (e.g. [AlMe(bht)]+ from MAO/BHT). These findings provide tentative interpretations for earlier observations of donor-dependent ionization tendencies of MAO and MAO/BHT and how TMA depleted MAOs can still be potent activators., A model cluster for methylaluminoxane (MAO) was used to study the tendency of model Lewis acidic sites to release neutral Al fragments or transient aluminum cations both for unmodified MAO and TMA-depleted MAO/BHT (TMA = trimethylaluminum; BHT = 2,6-di-tert-butyl-4-methylphenol). Albeit only sites of lower Lewis acidity are found in TMA depleted modified MAOs, they can release cationic Al fragments when treated with certain N-donors. This shows how TMA depleted MAOs can still be potent activators.

Compared to heterogenous Ziegler&ndash, Natta systems (ZNS), ansa-metallocene catalysts for the industrial production of isotactic polypropylene feature a higher cost-to-performance balance. In particular, the C2-symmetric bis(indenyl) ansa-zirconocenes disclosed in the 1990s are complex to prepare, less stereo- and/or regioselective than ZNS, and lose performance at practical application temperatures. The golden era of these complexes, though, was before High Throughput Experimentation (HTE) could contribute significantly to their evolution. Herein, we illustrate a Quantitative Structure &ndash, Activity Relationship (QSAR) model trained on a robust and highly accurate HTE database. The clear-box QSAR model utilizes, in particular, a limited number of chemically intuitive 3D geometric descriptors that screen various regions of space in and around the catalytic pocket in a modular way thus enabling to quantify individual substituent contributions. The main focus of the paper is on the methodology, which should be of rather broad applicability in molecular organometallic catalysis. Then again, it is worth emphasizing that the specific application reported here led us to identify in a comparatively short time novel zirconocene catalysts rivaling or even outperforming all previous homologues which strongly indicates that the metallocene story is not over yet.

Isotactic polypropylene (i-PP) is mainly produced with heterogeneous Ziegler-Natta (ZN) catalyst systems. Direct structural information on the active species is very difficult to achieve; as a matter of fact, the 13C NMR microstructure of the polymer has long been used as an indirect "fingerprint". For a long time, however, the intrinsically poor sensitivity of natural abundance 13C NMR spectroscopy hampered a complete evaluation of the microstructure, and many rare albeit important details escaped detection with standard tools and methods. The most prominent case is that of the regiodefects, which are specially important because they dictate ZN catalyst response to molecular hydrogen used as a chain transfer agent. In recent papers we have reported on the quantification of regioirregular 2,1 units in ZN i-PP by means of high-temperature cryoprobe 13C NMR. Here we shift the focus onto the stereochemical environment of such units, which was highlighted by comparing the spectra of suitable ZN PP fractions with those of model PP samples made with molecular catalysts of different structures and symmetries. The results lend support to our three-site model of ZN catalytic species, originally based on the stereochemistry of regioregular PP chains/blocks.

The field of stereoselective propene polymerization has been dramatically innovated by the discovery of homogeneous metallocene-based catalysts with well-defined and tunable molecular structure. Of all, "oscillating" metallocenes are probably the most ingenious and challenging example of catalyst design. Their catalytic species were built to "flip-flop" between a chiral and an achiral conformation, at a rate intermediate between those of monomer insertion and chain transfer. The result of this molecular switching would be a polypropylene with an isotactic/atactic stereoblock structure, performing as a thermoplastic elastomer. This essay discusses how the real polymerization mechanism differs from what the catalyst inventors had in mind, but also how - through fortunate circumstances their optimism has been rewarded.

The 150 MHz (13)C NMR microstructural analysis of polypropylene samples produced with two representative "oscillating" metallocene catalysts of largely different steric hindrance, namely [(2-(3,5-di-tert-butyl-4-methoxyphenyl)indenyl)(2)ZrP](+) and [(2-phenylindenyl)(2)ZrP](+) (P = polymeryl), and the implications on the origin of the stereocontrol are presented and discussed in detail. The original mechanistic proposal of an "oscillation" between a rac-like (isotactic-selective) and a meso-like (nonstereoselective) conformation cannot explain the observed polymer configuration. The isotactic-stereoblock nature of the polymers obtained with the former catalyst proves unambiguously that the active cation "oscillates" between the two enantiomorphous rac-like conformations at an average frequency that, even at high propene concentration, is only slightly lower than that of monomer insertion. The less-hindered [(2-phenylindenyl)(2)ZrP](+) gives instead a largely stereoirregular polypropylene, which is the logical consequence of a faster ligand rotation; however, depending on the use conditions (in particular, on the nature of the cocatalyst and the polarity of the solvent), the polymerization products may also contain appreciable amounts of a fairly isotactic fraction. The peculiar microstructure of this fraction, with isotactic blocks of the same relative configuration spanned by very short atactic ones, rules out the possibility that the latter are due to an active species in meso-like conformation and points rather to a conformationally "locked" rac-like species with restricted ring mobility. The hypothesis of a stereorigidity induced by the proximity to a counteranion, which would play the role of the interannular bridge in the rac-bis(indenyl) ansa-metallocenes, was tested by computer modeling on a [rac-(2-phenylindenyl)(2)ZrMe(C(3)H(6))][B(C(6)F(5))(4)] ion couple and found viable.