Search

In this paper, the influence of sewer physical properties on the structural deterioration of the Leuven (Belgium) sewers was investigated using logistic regression. The analysis revealed that out of the 10 variables considered, only three significantly affected the deterioration process, namely, age, material and length. Comparing the results of this study with similar studies revealed that no single set of factors can explain sewer deterioration, i.e. the process is a localised phenomenon. This study contributes to the widening and ascertaining of the limited - and often conflicting - knowledge with regard to the relationship between sewer properties and sewer deterioration. [ABSTRACT FROM AUTHOR]

The way excess sludge must be disposed of is a key factor in the choice of the appropriate phosphorus removal technique at municipal wastewater treatment plants. In Europe the ongoing trend of tightening the sludge spreading rules called for a serious reduction of its agricultural utilisation and the expansion of the (co-)incineration disposal route, which led to a shift towards more sophisticated sludge handling techniques. This paper illustrates the impact of different sludge handling techniques on the performance of chemical and enhanced biological phosphorus removal at municipal WWTPs. The main conclusion is that although enhanced biological phosphorus removal is particularly sensitive to the problem of return liquors from sludge treatment processes indirect dewatering and anaerobic stabilisation cannot be discarded altogether when considering its implementation. [ABSTRACT FROM AUTHOR]

Reports on the use of a pilot study and dynamic modelling to optimize the dimensions of different tanks during the renovation of the Wastewater Treatment Plant in Bruges, Belgium. Hydraulic dimensions; Pilot plant; Key points of the dynamic model; Storm water treatment; Biological treatment; Budget.

Dynamic simulation can be used to improve the design and performanceof the activated sludge process. This is illustrated by means of twocase studies: 1. The simulation of a full scale industrial plant treating nitrogen-rich wastewater by an intensive nitrification-denitrification process. By means of simulation the most important operational cost (dosage of an external carbon source) was optimised and a control strategy was proposed. 2. The simulation of a municipal wastewater treatment plant with the extension of nitrogen removal. Based on simulation the feasibility of the redesign was evaluated. In both casesthe wastewater composition was characterised and the biological model (the activated sludge IAWQ-model No. 1) calibrated. By means of respirometry and standard laboratory analyses it was possible to estimate the COD fractions of the wastewater and the parameters for heterotrophic and autotrophic growth of biomass. [ABSTRACT FROM AUTHOR]

Introduction: Many natural or synthetic compounds used in foods, dietary supplements, and food contact materials (FCMs) are suspected endocrine disruptors (EDs). Currently, scientific evidence to predict the impacts on biological systems of ED mixtures is lacking. In this study, three classes of substances were considered: i) phytoestrogens, ii) plant protection products (PPP) and iii) substances related to FCMs. Fourteen compounds were selected based on their potential endocrine activity and their presence in food and FCMs. Methods: These compounds were evaluated using an in vitro gene expression assay, the ERα-CALUX, to characterize their responses on the estrogen receptor alpha. Cells were exposed to fixed ratio mixtures and non-equipotent mixtures of full and partial agonists. The concentration-response curves measured for the three classes of compounds were characterized by variable geometric parameters in terms of maximum response (efficacy), sensitivity (slope) and potency (median effective concentration EC50). To account for these variations, a generic response addition (GRA) model was derived from mass action kinetics. Results: Although GRA does not allow us to clearly separate the concentration addition (CA) and independent action (IA) models, it was possible to determine in a statistically robust way whether the combined action of the chemicals in the mixture acted by interaction (synergy and antagonism) or by additive behavior. This distinction is crucial for assessing the risks associated with exposure to xenoestrogens. A benchmark dose approach was used to compare the response of phytoestrogen blends in the presence and absence of the hormone estradiol (E2). At the same time, 12 mixtures of 2-5 constituents including phytoestrogens, phthalates and PPPs in proportions close to those found in food products were tested. In 95% of cases, the response pattern observed showed a joint and independent effect of the chemicals on ER. Discussion: Overall, these results validate a risk assessment approach based on an additive effects model modulated by intrinsic toxicity factors. Here, the CA and IA approaches cannot be distinguished solely based on the shape of the concentration response curves. However, the optimized GRA model is more robust than CA when the efficacy, potency, and sensitivity of individual chemical agonists show large variations., Competing Interests: The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest. The handling editor RD declared a past co-authorship with the authors ME and IB., (Copyright © 2023 Elskens, Boonen and Eisenreich.)

Objectives: Dental composites remain under scrutiny regarding their (long-term) safety. In spite of numerous studies on the release of monomers both in vitro and in vivo, only limited quantitative data exist on the in vivo leaching of degradation products from monomers and additives. The aim of this observational study was for the first time to quantitatively and qualitatively monitor the release of parent compounds and their degradation products in saliva from patients undergoing multiple restorations., Materials and Methods: Five patients in need of multiple large composite restorations (minimally 5 up to 28 restorations) due to wear (attrition, abrasion, and erosion) were included in the study, and they received adhesive restorative treatment according to the standard procedures in the university clinic for Restorative Dentistry. Saliva was collected at different time points, starting before the restoration up until 24 h after the treatment with composite restorations. Saliva extracts were analyzed by liquid chromatography-mass spectrometry., Results: Leaching of monomers and degradation products was highest within 30 min after the placement of the restorations. The highest median concentrations of monomers were recorded for UDMA, BisEMA-3, and TEGDMA; yet, besides BisEMA-3 and TEGDMA, no monomers could be detected after 24 h. Mono- and demethacrylated degradation products remained present up to 24 h and concentrations were generally higher than those of monomers. In patients with multiple restorations, degradation products were still present in the sample taken before the next operation, several weeks after the previous operation., Conclusions: Exposure to residual monomers and degradation products occurs in the first hours after restoration. Monomers are present in saliva shortly after restoration, but degradation products can be detected weeks after the restoration confirming a long-term release., Clinical Significance: Future research should focus more on the release of degradation products from monomers and additives from resin-based materials given their prolonged presence in saliva after restoration., (© 2023. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

As viral genomic imprints in host genomes, endogenous viral elements (EVEs) shed light on the deep evolutionary history of viruses, ancestral host ranges, and ancient viral-host interactions. In addition, they may provide crucial information for calibrating viral evolutionary timescales. In this study, we conducted a comprehensive in silico screening of a large data set of available mammalian genomes for EVEs deriving from members of the viral family Flaviviridae, an important group of viruses including well-known human pathogens, such as Zika, dengue, or hepatitis C viruses. We identified two novel pestivirus-like EVEs in the reference genome of the Indochinese shrew (Crocidura indochinensis). Homologs of these novel EVEs were subsequently detected in vivo by molecular detection and sequencing in 27 shrew species, including 26 species representing a wide distribution within the Crocidurinae subfamily and one in the Soricinae subfamily on different continents. Based on this wide distribution, we estimate that the integration event occurred before the last common ancestor of the subfamily, about 10.8 million years ago, attesting to an ancient origin of pestiviruses and Flaviviridae in general. Moreover, we provide the first description of Flaviviridae-derived EVEs in mammals even though the family encompasses numerous mammal-infecting members. This also suggests that shrews were past and perhaps also current natural reservoirs of pestiviruses. Taken together, our results expand the current known Pestivirus host range and provide novel insight into the ancient evolutionary history of pestiviruses and the Flaviviridae family in general., (© The Author(s) 2022. Published by Oxford University Press on behalf of Society for Molecular Biology and Evolution.)

Objectives: Only little is known about degradation of methacrylate monomers. Therefore, using in vitro chemical and saliva degradation this study aimed to identify the degradation products of organic compounds present in resin-based dental materials., Methods: Ten dental monomers and nine polymerized dental resin-based materials were immersed for 24 h in chemical media (0.1 M HCl, 0.1 M NaOH) and human pooled saliva in order to identify leached monomers and degradation products from chemical and saliva degradation. Samples were analyzed using liquid chromatography coupled to high-resolution mass spectrometry to identify previously unknown degradation products., Results: During in vitro chemical degradation, uncured monomers were rapidly hydrolyzed into mono- and demethacrylated degradation products. During chemical degradation in alkaline conditions of polymerized materials, considered the worst-case scenario, only degradation products could be detected. In acidic conditions, monomers and their degradation products were detected. In addition, different additives such as EDMAB, DMPA and HMBP were present in acidic degradation samples. Degradation in human pooled saliva for 24 h to mimic the in vivo situation, resulted in the identification of both monomers and their degradation products., Clinical Significance: Using state-of-the-art high-resolution mass spectrometry previously unknown degradation products of commonly used monomers were identified for the first time. Results show that patients may be exposed to monomers and their degradation products in the first 24 h after restorative procedures. The results provide a base for further research on the degradation of resin-based dental composites in order to assess their safety using elution and toxicity studies., Competing Interests: Conflicts of interest The authors declare they have no conflict of interest., (Copyright © 2021 The Academy of Dental Materials. Published by Elsevier Inc. All rights reserved.)

Objectives: There is still much debate about the release of bisphenol A (BPA) from resin-based dental materials. Therefore, this study aimed to quantify BPA present as an impurity and to evaluate whether their degradation by salivary, bacterial, and chemical challenges could increase its release., Methods: BPA was determined in three different amounts (300, 400, and 500 µg) of eight unpolymerized resin-based materials (four composites, one fissure sealant, two adhesives and one root canal sealer). Next, polymerized samples (n = 5) of each material were immersed in 1 mL of whole human pooled saliva collected from adults, Streptococcus mutans (2 × 10 7 CFU/mL), and acidic (0.1 M HCl), alkaline (0.1 M NaOH), and control media, respectively. The amount of BPA was quantified using an UPLC-MS/MS method including derivatization of BPA by pyridine-3-sulfonyl chloride., Results: Only the composites contained trace amounts of BPA above the limit of quantification (ranging from 301±32 pg PBA/mg to 1534±62 pg BPA/mg), most likely as impurity from the synthesis of the monomers. The amounts of BPA released from polymerized materials upon salivary and bacterial degradation were too low for accurate quantification, but in water, quantifiable amounts of BPA were released from all materials. In alkaline media, the BPA release from two composites was significantly decreased, while the release from one adhesive was significantly increased, compared to water., Conclusions: BPA already present in unpolymerized resin-based materials may account for the release of BPA after polymerization. There was no clear indication that short-term material degradation leads to increased release of BPA., (Copyright © 2021 Elsevier Ltd. All rights reserved.)

Objective: The biocompatibility of resin based dental composites has not yet been fully characterized even though certain monomers used in these composites are synthesized from Bisphenol A (BPA), a well-known estrogenic endocrine disruptor. As a result, they show structural relationship to BPA and can contain it as an impurity. Therefore, the estrogenic activity of 9 monomers, 2 photoinitiators, one photostabilizer and leachates of 4 commercially available composites was determined., Methods: The ERα-CALUX bioassay was used to determine both agonistic and antagonistic estrogenic activities of the pure compounds (BPA, BisDMA, BisGMA, BisEMA(3), BisEMA(6), BisEMA(10), TEGDMA, TCD-DI-HEA, BADGE, UDMA, HMBP, DMPA, CQ) and the leachates of cured composite disks. The leachates of 4 commercially available composites (Solitaire 2, Ceram.x Spectra ST, G-ænial Posterior and Filtek Supreme XTE) in water and 0.1 M NaOH (pH = 13, 'worst-case scenario') were tested for estrogenic activity (pooled leachates from 10 cured composite disks)., Results: Agonistic estrogenic activity was found for the monomer BisDMA, the photostabilizer HMBP and photoinitiator DMPA. All leachates from the 4 tested composites showed significant agonistic estrogenic activity higher than the DMSO control, and the highest activity (potency and efficacy) was found for Solitaire 2, followed by Ceram.x Spectra ST. Furthermore, antagonistic estrogenic activity was found in the leachates from G-ænial Posterior., Significance: These results show that significant estrogenic activity was found in all leachates of the cured composite disks, and that this estrogenicity is most likely due to a mixture effect of multiple estrogenic compounds (including BPA, HMBP and DMPA). This indicates that further research into the endocrine activity of all the compounds that are present in these composites (even at low quantities) and their possible mixture effect is warranted to guarantee their safe use., (Copyright © 2021 The Academy of Dental Materials. Published by Elsevier Inc. All rights reserved.)

Objectives: BPA release from composites on the short term has been reported in several in-vitro and in-vivo studies. However, it remains unclear whether these materials also leach BPA on the long term. Even though composites may release various (BPA-based) methacrylate monomers up to one year, quantitative data about BPA have not been reported due to the lack of a sensitive method to accurately quantify low levels of BPA. In this context, the aim of the study was to quantify the one-year release of BPA with an optimized analytical method., Methods: Composite disks (n = 6, 6 mm diameter and 2 mm height) from four commercial materials (G-ӕnial Posterior, Venus, Ceram.x mono and Filtek Supreme XTE) were immersed in 1 mL of water or ethanol as extraction solvent and stored in the dark at 37 °C. The extraction solvent was renewed weekly for a period of 52 weeks. Samples were derivatized with pyridine-3-sulfonyl chloride before analysis with ultra-pressure liquid chromatography tandem mass spectrometry (UPLC-MS/MS)., Results: Derivatizing BPA increased the sensitivity of the analytical method and allowed accurate quantification of very low levels of BPA (i.e. 0.78 pmol BPA). BPA eluted continuously in ethanol from all four tested composites over a period of one year. BPA elution was clearly higher when ethanol was used as extraction solution. In water, BPA eluted could be detected up to one year, but levels could not be accurately quantified anymore after several weeks., Significance: Composites can be considered as a potential long-term source of BPA, and thus should not be neglected when assessing the overall exposure to endocrine disrupting chemicals., (Copyright © 2021 The Academy of Dental Materials. Published by Elsevier Inc. All rights reserved.)

Here, we identified a novel class of compounds which demonstrated good antiviral activity against dengue and Zika virus infection. These derivatives constitute intermediates in the synthesis of indole (ervatamine-silicine) alkaloids and share a tetracyclic structure, with an indole and a piperidine fused to a seven-membered carbocyclic ring. Structure-activity relationship studies indicated the importance of substituent at position C-6 and especially the presence of a benzyl ester for the activity and cytotoxicity of the molecules. In addition, the stereochemistry at C-7 and C-8, as well as the presence of an oxazolidine ring, influenced the potency of the compounds. Mechanism of action studies with two analogues of this family (compounds 22 and trans -14) showed that this class of molecules can suppress viral infection during the later stages of the replication cycle (RNA replication/assembly). Moreover, a cell-dependent antiviral profile of the compounds against several Zika strains was observed, possibly implying the involvement of a cellular factor(s) in the activity of the molecules. Sequencing of compound-resistant Zika mutants revealed a single nonsynonymous amino acid mutation (aspartic acid to histidine) at the beginning of the predicted transmembrane domain 1 of NS4B protein, which plays a vital role in the formation of the viral replication complex. To conclude, our study provides detailed information on a new class of NS4B-associated inhibitors and strengthens the importance of identifying host-virus interactions in order to tackle flavivirus infections.

Objective: There is still much debate about the release of bisphenol-A (BPA) from dental materials. Therefore, this study aimed to quantify BPA present as an impurity in both BPA-based and non-BPA-based monomers and to evaluate whether these monomers may degrade to BPA upon salivary, bacterial, and chemical challenges., Methods: BPA was determined in three different amounts (1, 2, and 3 μmol) of each monomer (TEGDMA, UDMA, mUDMA, BisGMA, BisEMA-3, -6, -10, -30, BisPMA, EBPADMA urethane, BADGE, and BisDMA). Next, the monomers (3 μmol) were immersed in whole human pooled saliva collected from adults, Streptococcus mutans (2 × 10 7 CFU/mL), and acidic (0.1 M HCl), alkaline (0.1 M NaOH), and control media. The amount of BPA was quantified using a specific and highly sensitive UPLC-MS/MS method including derivatization of BPA by pyridine-3-sulfonyl chloride., Results: The monomers BisGMA and BisEMA-3 contained trace amounts (0.0006% and 0.0025%, respectively) of BPA as impurities of their synthesis process. BPA concentrations increased when the monomers BisGMA, BisEMA-3, BisEMA-6, BisEMA-10, BisPMA and BADGE were exposed to saliva and S. mutans, indicating degradation of a small amount of monomer into BPA. In addition, BisPMA and BADGE degraded into BPA under alkaline conditions. The conversion rate of the monomers into BPA ranged between 0.0003% and 0.0025%., Significance: Impurities and degradation of BPA-based monomers may account for the release of BPA from resin-based dental materials. Even though the detected amounts of BPA due to monomer impurity were small, manufacturers of dental materials can reduce the BPA content by using only monomers of the highest purity. Considering the overall current trend towards BPA-free materials, it may be recommendable to investigate whether non-BPA based monomers can be used in dental resin-based materials., (Copyright © 2021 The Academy of Dental Materials. Published by Elsevier Inc. All rights reserved.)

Hepatitis C virus (HCV; genus Hepacivirus ) represents a major public health problem, infecting about three per cent of the human population. Because no animal reservoir carrying closely related hepaciviruses has been identified, the zoonotic origins of HCV still remain unresolved. Motivated by recent findings of divergent hepaciviruses in rodents and a plausible African origin of HCV genotypes, we have screened a large collection of small mammals samples from seven sub-Saharan African countries. Out of 4,303 samples screened, eighty were found positive for the presence of hepaciviruses in twenty-nine different host species. We, here, report fifty-six novel genomes that considerably increase the diversity of three divergent rodent hepacivirus lineages. Furthermore, we provide strong evidence for hepacivirus co-infections in rodents, which were exclusively found in four sampled species of brush-furred mice. We also detect evidence of recombination within specific host lineages. Our study expands the available hepacivirus genomic data and contributes insights into the relatively deep evolutionary history of these pathogens in rodents. Overall, our results emphasize the importance of rodents as a potential hepacivirus reservoir and as models for investigating HCV infection dynamics., (© The Author(s) 2021. Published by Oxford University Press.)

Recently collected dietary exposure data on mineral oil saturated (MOSH) and aromatic (MOAH) hydrocarbons were used to evaluate the risks associated with exposure to mineral oil through food for the Belgian population. For MOSH, the no observed adverse effect level (NOAEL) value of 19 mg kg -1 bw day -1 based on the hepatic inflammation-associated granulomas found in a 90-day oral study in F-344 rats was used as point of departure (PoD). Due to existing toxicological uncertainties, the margin of exposure (MOE) approach was applied. In all investigated scenarios, the MOE values were well above 100, indicating that there is no direct health concern related to MOSH exposure for the Belgian population. Nevertheless, more appropriate risk assessment approaches for MOSH based on adequate PoD are needed. For dietary exposure to MOAH, which are potentially genotoxic and carcinogenic, no MOE values could be calculated due to the lack of adequate dose-response carcinogenicity data. In two investigated worst-case scenarios, a health concern related to MOAH exposure could not be excluded, highlighting that more data are needed to perform an adequate risk assessment. The possibility to use in vitro bioassays to collect such additional toxicological information for MOAH present in food samples was also investigated., (Copyright © 2021 Elsevier Ltd. All rights reserved.)

Root canal sealers are commonly used to endodontically treat teeth with periapical infections. Some root canal sealers based on epoxy resin contain bisphenol A diglycidyl ether (BADGE) and bisphenol F diglycidyl ether (BFDGE). The presence of these chemicals is of concern due to the close contact to the blood stream at the apex and the long setting times of up to 24 h. These chemicals, or any of their degradation products or metabolites, can then exert their toxic effects before being excreted. This study aimed to identify the phase I in vitro biotransformation products of BADGE and BFDGE using human liver microsomes. During incubation with microsomal fractions, the epoxides were rapidly hydrolysed in a NADPH independent manner resulting in the formation of BADGE.2H 2 O and BFDGE.2H 2 O. Further, oxidative reactions, such as hydroxylation and carboxylation, generated other BADGE metabolites, such as BADGE.2H 2 O-OH and BADGE.H 2 O.COOH, respectively. For BFDGE, further oxidation of BFDGE.2H 2 O led to the newly reported carboxylic acid, BFDGE.H 2 O.COOH. In total, three specific metabolites have been identified which can serve in future human biomonitoring studies of BADGE and BFDGE., Competing Interests: Declaration of Competing Interest The authors declare they have no conflict of interest., (Copyright © 2020 Elsevier B.V. All rights reserved.)

Dental resin systems have been in use for several decades. (Meth)acrylic monomers are an important part of the matrix system and are either based on BPA while others lack the BPA core. The degree of conversion during restoration is in general between 50-70 % allowing leaching from unreacted monomers to the oral cavity where they can be taken up through the pulp or gastrointestinal tract after ingestion with subsequent hepatic metabolism. This study identified the in vitro Phase I and Phase II metabolism of the dental resin monomers BisGMA, UDMA, BisPMA and TCD-DI-HEA, using human liver microsomes (HLM) and human liver cytosols. During Phase I incubation with HLM, the (meth)acrylic acid in the monomers was rapidly removed followed by oxidative and hydroxylation pathways. For BisPMA an O-dealkylation pathway occurred resulting in the formation of BPA. The carbamates present in TCD-DI-HEA and UDMA were resistant to biotransformation reactions. Phase II biotransformation products were only observed for BisPMA and included conjugation reactions with sulphate and glucuronic acid. In total 4, 3, 12 and 3 biotransformation products were identified in this study for BisGMA, UDMA, BisPMA and TCD-DI-HEA respectively. Possible human health effects of these biotransformation products remain unclear due to limited data availability., (Copyright © 2019 Elsevier B.V. All rights reserved.)

Since 2011, the World Health Organization has encouraged a global phase-down of the use of dental amalgam and actively supported the use of alternative, resin-based dental materials. The resins consist of (meth)acrylate monomers derived from Bisphenol A (BPA), such as Bisphenol A glycidyl methacrylate (BisGMA) and Bisphenol A ethoxylate methacrylate (BisEMA) or triethylene glycol dimethacrylate (TEGDMA) and urethane dimethacrylate (UDMA) which lack the BPA backbone. Besides monomers, other compounds such as photoinitiators and stabilizing agents can be present in the dental resin matrices. The current study consists in the development of an analytical method for the separation and identification of dental material components using LC-QTOF-MS. The developed method was applied on several dental material ingredients, unpolymerized composite resins, and a common dental sealant. The acquired high resolution accurate-mass data was analyzed using suspect screening with an in-house developed library. Next to the main components, various isomers and impurities related to the production of the main component have been detected and identified in the dental material ingredients. In total, 39 chemicals have been identified in the analyzed dental materials. On average 15 chemicals have been identified. Major components, such as BisEMA, BisGMA and TEGDMA were identified although they were not always stated in the material safety data sheets. Minor components included photoinitiators, such as ethyl 4-dimethyl aminobenzoate (EDMAB) and (meth)acrylates impurities originating from production of main ingredients., (Copyright © 2018 Elsevier B.V. All rights reserved.)

There is a growing necessity to acquire more profound knowledge on the quantity of eluates from resin-based dental materials, especially with regard to bisphenol A (BPA). The aim of the present study was to develop a highly sensitive method to characterize the short-term release of BPA in saliva with ultra-performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS), using an extraction step and additional derivatization of BPA with pyridine-3-sulfonyl chloride. Light-cured resin-based composites were incubated at 37 °C in 1 mL artificial saliva, which was refreshed daily for one week. The final protocol allows accurate quantification of very low levels of BPA in samples of artificial saliva (i.e. 1.10 pmol BPA/mL or 250 pg/mL). The daily BPA-release from dental composites, ranging from 1.10 to 7.46 pmol BPA/mL, was characterized over a period of 7 days. The highest total amount of BPA was released from Solitaire 2 (24.72 ± 2.86 pmol), followed by G-ænial Posterior (15.51 ± 0.88 pmol) and Filtek Supreme XTE (12.00 ± 1.31 pmol). In contrast, only trace amounts of BPA were released from Ceram.x Universal. This UPLC-MS/MS method might be used for clinical research focusing on the evaluation of the clinical relevance of BPA release from dental materials.

A new one-dimensional clarifier model was developed, including components of existing models, and extended with a height-dependent cross-sectional area and two flowrate-dependent dispersion coefficients. This model is evaluated using data from a detailed one-month measuring campaign on a full-scale wastewater treatment plant. The data included hourly sludge concentration profile, sludge heights at 10 minute intervals, sludge concentrations in inlet, effluent and recycle flows and regular settling properties characterised by batch setting tests. Due to the poor quality concentration measurements at the surface of the clarifier, the model was not calibrated to perform well in concentration predictions at this surface. However, excellent descriptive capabilities were obtained for sludge profiles and blanket level. The Cho et al. setting velocity function was found to be significantly better in terms of description capability than the more traditional Vesilind function.

The provision of reliable treatment has always been a priority in sanitary engineering. However, there is an ever-increasing pressure to meet desirable standards at reduced costs. This paper sets out a methodology to enhance the likelihood of a satisfactory allocation of the resources while providing reliable treatment. The procedure was gradually developed to optimise the massive capital investment of the Flemish Government to comply with the effluent standards set in the EU Directive 271/91. The methodology makes an extended use of dynamic modelling. To facilitate the identification and estimation of the uncertainty, a probabilistic Monte Carlo engine is coupled to the dynamic models. In doing so this approach provides a way of explicitly incorporating uncertainty and variability in the process analysis. The procedure is examined in an upgrade of a conventional WWTP towards stricter effluent norms on nutrients. The results suggest that the procedure can support the decision-making process under uncertainty conditions and enhance the likelihood of meeting effluent standards not entailing above-normal capital investments. The analysis led to reducing the capital investment by 43%, producing savings of more than 1.2 million Euros.