Search

The provision of wireless and battery-free power is key to extending the applications of body-worn sensing electronics. This paper investigates the design of an IPT system for a body-worn scenario where the challenges include highly variable coupling, the requirement for the coil/s to be flexible, and close proximity to the body. Variable coupling results in a system that must operate with received powers ranging over orders of magnitude, whilst the use of flexible coils reduces the Q-factor and results in the potential for inductance variation. The human exposure considerations limit both the maximum field strengths that the wearer of a receiver coil might experience and the field strengths that a third party might be exposed to. In this paper, analytical models are used to identify key design variables and to guide the design synthesis of an IPT system for a wrist-worn medical sensor. Practical circuits to drive the transmit coil and to interface the receive coil with the load electronics are described. A prototype system is tested to validate the theoretical analysis, providing power greater than 2 mW to the sensor over a hemispherical region up to 250 mm in radius from the transmit coil. [ABSTRACT FROM AUTHOR]

E-textiles have emerged as a fast-growing area in wearable technology for sports and fitness due to the soft and comfortable nature of textile materials and the capability for smart functionality to be integrated into familiar sports clothing. This review paper presents the roles of wearable technologies in sport and fitness in monitoring movement and biosignals used to assess performance, reduce injury risk, and motivate training/exercise. The drivers of research in e-textiles are discussed after reviewing existing non-textile and textile-based commercial wearable products. Different sensing components/materials (e.g., inertial measurement units, electrodes for biosignals, piezoresistive sensors), manufacturing processes, and their applications in sports and fitness published in the literature were reviewed and discussed. Finally, the paper presents the current challenges of e-textiles to achieve practical applications at scale and future perspectives in e-textiles research and development. [ABSTRACT FROM AUTHOR]

The dc power collected by radio frequency energy harvesting (RFEH) absorbing surfaces is limited by their physical aperture. Here, a compact, conformable, and ultrathin sub-1 GHz large-area RFEH surface is proposed based on electrically small ($ka=0.58$) “wire-type” rectenna elements, with an effective area exceeding its physical aperture size. Using optimized large-signal complex source tuning, the rectifiers achieve up to 36% measured power conversion efficiency (PCE) at =20 dBm. The proposed 15 cm-diameter six-element array generates a 27.5 $\mu \text{W}$ at 1 V output from a $0.17~\mu \text{W}$ /cm2 incident power density across a 40 $\text{k}\Omega $ load. Owing to its series connection, the voltage output is boosted, and the load resistance dependence is suppressed enabling over 60% of the maximum RF-to-dc PCE to be preserved for loads between 7 and 100 $\text{k}\Omega $ , with an area-normalized figure-of-merit nearly 100% higher than previous arrays. The proposed array is integrated with a commercial DC-DC converter and demonstrated powering a Bluetooth low energy (BLE) wireless sensor node (WSN) from an unprecedented incident power density of 0.25 $\mu \text{W}$ /cm2. A practical demonstration using a commercial 3 W, 915 MHz Powercast source is presented, showing an 11 m operation range with a 1 V output and illustrating the impact of polarization mismatch on the proposed array. [ABSTRACT FROM AUTHOR]

Improvements of the d(sub 33) co-efficient for thick-film lead zirconate titanate (PZT) layers are detailed. The combination of small and large particles does increase the d(sub 33) of the film and justifies the investigation and it is shown that the consistency of the results can be increased in comparison to the ball milled devices, although they are not as consistent as the attritor3 devices.

Radio frequency identification (RFID) represents an emerging platform for passive RF-powered wireless sensing. Differential Multi-port RFID systems are widely used to enable multiple independent measurands to be gathered, or to overcome channel variations. This paper presents a dual-port/dual-integrated circuit (IC) RFID sensing tag based on a shared aperture dual-polarized microstrip antenna. The tag can be loaded with different sensors where the received signal strength indicator (RSSI) of one IC is modulated using a sensor, and the other acts as a measurand-insensitive reference, for differential sensing. The 868 MHz tag maintains a minimum unloaded read range of 14 m insensitive to deployment on metals or lossy objects, which represents the longest reported range of a multi-port RFID sensing tag. The tag is loaded with a light-dependent resistor (LDR) to demonstrate its functionality as a battery-less wireless RFID light sensor. Following detailed RF characterization of the LDR, it is shown that the impedance, and consequently the RSSI, of the sensing tag are modulated by changing the light intensity, whereas the reference port maintains a mostly unchanged response for a correlated channel. The proposed tag shows the potential for channel variations-tolerant differential RFID sensing platforms based on polarization-diversity antennas. [ABSTRACT FROM AUTHOR]

This article presents a textile antenna for dual-band simultaneous wireless information and power transfer (SWIPT). The antenna operates as a 2.4 GHz off-body communications antenna and a sub-1 GHz (785–875 MHz) broad-beam rectenna. Incorporated within the broadside microstrip antenna is a high-impedance rectenna for sub-1 GHz power harvesting. Utilizing antenna-rectifier co-design, the rectenna eliminates the rectifier matching network. The textile antenna is fabricated on a felt substrate and utilizes conductive fabrics for the antenna. At 2.4 GHz, the antenna achieves a realized gain of 7.2 dBi on a body phantom and a minimum radiation efficiency of 63%, with and without the rectifier. The rectenna achieves a best-in-class RF to dc efficiency of 62% from 0.8 $\mu \text{W}$ /cm2, representing over 25% improvement over state-of-the-art textile rectennas and demonstrating that SWIPT does not detrimentally affect the energy harvesting or communications performance. The antenna/rectenna occupies an electrically small area of $0.213\times 0.19\,\,\lambda ^{2}_{0}$. This antenna is the first dual-band, dual-mode antenna demonstrated on textiles for SWIPT applications and the first dual-band matching network-free SWIPT rectenna. [ABSTRACT FROM AUTHOR]

This paper presents the modeling and optimization of an electromagnetic-based generator for generating power from ambient vibrations. Basic equations describing such generators are presented and the conditions for maximum power generation are described. Two-centimeter scale prototype generators, which consist of magnets suspended on a beam vibrating relative to a coil, have been built and tested. The measured power and modeled results are compared. It is shown that the experimental results confirm the optimization theory. Index Terms--Displacement, energy conversion, generators and resonance.

Despite the recent advances in textile antennas, in complete systems such as a rectenna, the efficiency of fully textile solutions has been over 46% lower than hybrid textile/rigid implementations. This article presents a fully textile rectenna for ultralow-power sub-μW/cm2 applications. A dual-polarized omnidirectional low-profile textile antenna is presented. The rectenna is based on a compact inductively matched rectifier. The textile-based rectifier occupies 0.22 cm2 and achieves a state-of-the-art power conversion efficiency (PCE) of 41.8% at −20 dBm, at 820 MHz, despite its lossy substrate. A triple-band rectifier is then designed and fabricated to show the scalability of the matching approach. The rectifier is characterized using a new figure of merit “average PCE” over a time period while charging a capacitor. Time-varying S-parameters are used to quantify the impact of the capacitor’s charge on the impedance matching. The rectifier directly charges a 1.32 mF capacitor up to 1 V in 0.41 and 4.5 s from 10 and 0 dBm, respectively. Wireless testing of the proposed rectenna demonstrates over 50% and 40% (PCE) below 1 μW/cm2 in space and on-body, respectively. The rectenna efficiently receives power from mismatched polarization and with a 360° half-power beamwidth. [ABSTRACT FROM AUTHOR]

In this article, organic light-emitting electrochemical cells (OLECs) have been fabricated on a substrate consisting of a standard woven polyester cotton textile. The textile substrate is presmoothed by first screen printing an ultraviolet (UV) curable polyurethane layer, termed the interface layer. Solution-processed spray coating is then utilized to deposit all the functional layers on the textile to achieve fully spray-coated flexible OLECs. OLEC devices were initially fabricated on ITO-coated glass substrates for process optimization. Then, the OLECs were fabricated on flexible textile using the optimized spray coating process. Finally, both OLECs devices on the glass and textile substrates were encapsulated by stencil printing epoxy before testing in an ambient environment. The OLECs on ITO-coated glass exhibit a turn-on voltage of 3 V, a brightness level of 200 cd/m2 and a lifetime of at least 60 min. The OLECs on textile exhibit a turn-on voltage of 4 V, a brightness level of 80 cd/m2 level and a lifetime of at least 30 min. [ABSTRACT FROM AUTHOR]

According to current trends in healthcare sensing technologies, we describe a textile-based pressure sensing matrix that can be integrated in the mattress of a smart bed to characterize sleeping posture/movement of a subject and to extract breathing activity. The pressure mapping layer is developed as a matrix of 195 piezoresistive sensors, it is entirely made of textile materials, and it is the basic component of a smart bed that can perform sleep analysis, can extract physiological parameters, and can detect environmental data related to subject's health. In this paper, we show the principle of the pressure mapping layer and the architecture of the dedicated electronic system that we developed for signal acquisition. In addition, we describe the algorithms for posture/movement classification (dedicated artificial neural network) and for extraction of the breathing rate (frequency domain analysis). We also perform validation of the system to quantify the accuracy/precision of the posture classification and the statistical analysis to compare our breathing rate estimation with the gold standard. [ABSTRACT FROM AUTHOR]

Millimeter-wave (mmWave) bands, a key part of future 5G networks, represent a potential channel for RF energy harvesting, where the high-gain antenna arrays offer improved end-to-end efficiency compared with sub-6-GHz networks. This article presents a broadband mmWave rectenna, the first rectenna realized on a flexible textile substrate for wearable applications. The proposed novel antenna’s bandwidth extends from 23 to 40 GHz, with a minimum radiation efficiency of 67% up to 30 GHz, over 3-dB improvement compared with a standard patch. A stable gain of more than 8 dB is achieved based on a textile reflector plane. The antenna is directly connected to a textile-based microstrip voltage doubler rectifier utilizing commercial Schottky diodes. The rectifier is matched to the antenna using a tapered line feed for high-impedance matching, achieving broadband high voltage sensitivity. The rectifier has a peak RF–dc efficiency of 12% and a 9.5-dBm 1-V sensitivity from 23 to 24.25 GHz. The integrated rectenna is demonstrated with more than 1.3-V dc output from 12 dBm of mmWave wireless power across a 28% fractional bandwidth from 20 to 26.5 GHz, a 15% half-power fractional bandwidth, and a peak output of 6.5 V from 20 dBm at 24 GHz. [ABSTRACT FROM AUTHOR]

Radio-frequency (RF) energy harvesting (RFEH) and radiative wireless power transfer (WPT) have attracted significant interest as methods of enabling battery-free sustainable wireless networks. Rectifying antennas (rectennas) are the cornerstone of WPT and RFEH systems and critically affect the amount of dc power delivered to the load. The antenna element of the rectenna directly impacts the radiation-to-ac harvesting efficiency, which can vary the harvested power by orders of magnitude. In this article, antenna designs employed in WPT and ambient RFEH applications are reviewed. Reported rectennas are categorized based on two main criteria: the antenna-rectifier impedance bandwidth and the antenna's radiation properties. For each criterion, the figure of merit (FoM) is identified for different applications and reviewed comparatively. [ABSTRACT FROM AUTHOR]

The theory, design and simulation of electromagnetic micropower generators with electroplated micromagnets fabricated using standard microelectromechanical system processing techniques are discussed. The voltage and power that can be generated from different designs are determined using electromagnetic two-dimensional finite element analysis simulations.