Search

The detection of 100 ppm of butane in superatmospheric N2 on air with an m-lines setup is reported. The sensing elements were ZnO-nanostructured coatings prepared by pulsed laser deposition and a refractive index in the 1.95 region was observed.

We demonstrated that doping or covering with Au nanoclusters boosts gas sensing effectiveness of optical metal oxide sensors. The sensing response of pulsed laser deposited ZnO films as sensing element was tested by m-line technique for low concentration (1000 ppm) of butane in environmental N2. The optical interrogation was performed for three types of coatings: undoped ZnO, undoped ZnO structures partially covered with Au nanoclusters, or obtained from Au (0.5 wt %) doped ZnO targets. Nanocluster coating tripled the sensitivity, while doping resulted in an increase of up to 45% as compared with simple structures. [ABSTRACT FROM AUTHOR]

Active protein and bioceramic calcium hydroxyapatite (HA) bilayers were grown by combining conventional pulsed laser deposition (PLD) and matrix-assisted pulsed laser evaporation (MAPLE) techniques. A pulsed UV KrF* excimer laser was used for the irradiations. The HA layers were grown by PLD. Proteins with antimicrobial action were attached to the bioceramic layers using MAPLE. The composite MAPLE targets were obtained by dissolving the proteins powder in distilled water. The crystalline status and chemical composition of the obtained structures were studied by X-ray diffractometry and Fourier transform infrared spectroscopy. The layers were grown for the design of advanced future metal implants coatings, ensuring both enhanced bone formation and localized antimicrobial therapy. Our results demonstrated that protein coatings improve bone cell proliferation in vitro. Immunofluorescence experiments show that actin filaments stretch throughout bone cells and sustain their optimal spreading. © 2013 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 101A: 2706-2711, 2013. [ABSTRACT FROM AUTHOR]

We introduce a combinatorial approach for the fabrication of organic biopolymer thin films. Structures with compositional gradient are obtained by simultaneous laser vaporization of two distinct targets. Matrix-assisted pulsed laser evaporation deposition method was applied to obtain a compositional library of levan and oxidized levan in form of thin film. The gradient of film composition and structure was demonstrated by infrared spectroscopy while in vitro cell culture assays illustrated characteristic responses of cells to specific surface regions. The method can rapidly generate discrete areas of organic film compositions with improved properties than starting materials. [ABSTRACT FROM AUTHOR]

Nafion/oxide composite membranes were produced by pulsed laser ablation method using UV laser pulses generated by a COMPEXPro 205 KrF* excimer laser source λ = 248 nm and τFWHM ≈ 25 ns. We selected TiO2 material and distributed it uniformly over the surface of Nafion 112 membrane using 100 and 250 laser pulses and an incident laser fluence set at 5 J cm–2 were applied to improve the water retention property and corresponding proton conductivity under high temperature operating conditions. TGA and DSC methods were used to characterize the thermal stability of the membranes. Furthermore, UV-Vis spectroscopy experiments showed incorporation of the inorganic phase in the polymer matrix. Water uptake and proton conductivity characterizations of the Nafion composite membranes were carried out, and the results demonstrated that there was higher water uptake and an increased proton conductivity at 120 °C temperature, compared with Nafion 112 membrane. [ABSTRACT FROM AUTHOR]

Aluminium nitride (AlN) films obtained by pulsed laser deposition (PLD) at different low ambient nitrogen pressure have been optically investigated by spectral ellipsometry within the 300–800 nm wavelength range, Sellmeier and Wemple–DiDomenico approximation approaches have been applied for the ellipsometric data analysis. Optical parameters such as refractive index and single oscillator energies of deposited films were estimated and their dependence on the N2 pressure was studied. The obtained refractive index values of AlN films are around 2 in a wide wavelength region above 400 nm and suggest the growth of a polycrystalline structure. The relatively low (<3.4 eV) threshold energies indicate the formation of a defective and disordered structure, formed during the deposition process. [ABSTRACT FROM AUTHOR]

The purpose of the present study was to examine the possibility of laser-machining of CuInSe2-based photovoltaic devices. Therefore, ablation thresholds and ablation rates of ZnO, CuInSe2 and Mo thin films have been measured for irradiation with nanosecond laser pulses of ultraviolet and visible light and subpicosecond laser pulses of a Ti : sapphire laser. The experimental results were compared with the theoretical evaluation of the samples heat regime obtained from numerical calculations. In addition, the photo-electrical properties of the solar cells were measured before and after laser-machining. Scanning electron microscopy and energy dispersive x-ray analyses were employed to characterize the laser-induced ablation channels. As a result, two phenomena were found to limit the laser-machining process: (i) residues of Mo that were projected onto the walls of the ablation channel and (ii) the metallization of the CuInSe2 semiconductor close to the channel. Both effects lead to a shunt in the device that decreases the photovoltaic efficiency. As a consequence of these limiting effects, micromachining of CuInSe2-based solar cells was not possible with nanosecond laser pulses. Only subpicosecond laser pulses provided selective or complete ablation of the thin layers without a relevant change in the photoelectrical properties. [ABSTRACT FROM AUTHOR]

We investigate electron-phonon coupling in metals by analyzing the composition of plumes produced by laser ablation with two delayed short laser pulses. Samples of Ti, Zr, and Hf are chosen since they have similar thermo-physical properties but significant different atomic masses. It is shown that the atomic emission intensity increases with the interpulse delay, whereas the nanoparticle emission intensity decreases. The characteristic time of plume changes is found to depend linearly on the metals' atomic mass. Theoretical considerations suggest that the measured times equal to the characteristic times of electron-lattice relaxation. [ABSTRACT FROM AUTHOR]

Abstract: The extension of pulsed laser deposition to the synthesis on Ti substrates of β-tricalcium phosphate (β-TCP) coatings doped with manganese is reported. Targets sintered from two crystalline Mn-doped β-TCP powders (with the composition Ca2.9Mn0.1(PO4)2 and Ca2.8Mn0.2(PO4)2) were ablated with an UV KrF* (λ =248nm, τ ∼7ns) laser source. X-ray diffraction and energy dispersive X-ray spectroscopy investigations showed that the films, while prevalently amorphous, had a Ca/P ratio of about 1.50–1.52. Scanning electron microscopy analyses revealed a rather homogeneous aspect of the coatings which were molded to the relief of the chemically etched Ti substrate. Fluorescence microscopy was applied to test the proliferation of mesenchymal stem cells grown on the obtained biostructures. Our investigations found that, even 14 days after cultivation, the synthesized films were not cytotoxic. On the contrary, they showed excellent bioactivity, as demonstrated by the neat spread of the cells over the entire surface of Mn-doped β-TCP. When tested in osteoprogenitor cell culture, the Ca2.8Mn0.2(PO4)2 samples revealed a higher potential for proliferation and better viability compared with Ca2.9Mn0.1(PO4)2. [Copyright &y& Elsevier]

Abstract: Anatase phase titanium dioxide (TiO2) thin films were grown by pulsed laser deposition on 〈001〉 SiO2 substrates. An UV KrF* (λ =248nm, τ FWHM ≅20ns, ν =2Hz) excimer laser was used for the irradiation of the TiO2 targets. The substrates were kept at room temperature or heated during the film deposition at values within the 100–500°C range. The crystalline quality of the films and their chemical composition were investigated by X-ray diffractometry and energy dispersive X-ray spectroscopy. The optical properties were studied by a double beam spectrophotometer in the spectral range of 400–1200nm. At substrate temperatures higher than 300°C, the structure of the deposited thin films changes from poorly to well crystallised, corresponding to the tetragonal TiO2 anatase phase. The average optical transmittance in the visible-infrared spectral range of the films is higher than 85% which makes them suitable for sensor applications. [Copyright &y& Elsevier]

We demonstrate that elemental analysis of glass with a measurement precision of about 10% can be performed via calibration-free laser-induced breakdown spectroscopy. Therefore, plasma emission spectra recorded during ultraviolet laser ablation of different glasses are compared to the spectral radiance computed for a plasma in local thermodynamic equilibrium. Using an iterative calculation algorithm, we deduce the relative elemental fractions and the plasma properties from the best agreement between measured and computed spectra. The measurement method is validated in two ways. First, the LIBS measurements are performed on fused silica composed of more than 99.9% of SiO 2 . Second, the oxygen fractions measured for heavy flint and barite crown glasses are compared to the values expected from the glass composing oxides. The measured compositions are furthermore compared with those obtained by X-ray photoelectron spectroscopy and energy-dispersive X-ray spectroscopy. It is shown that accurate LIBS analyses require spectra recording with short enough delays between laser pulse and detector gate, when the electron density is larger than 10 17 cm − 3 . The results show that laser-induced breakdown spectroscopy based on accurate plasma modeling is suitable for elemental analysis of complex materials such as glasses, with an analytical performance comparable or even better than that obtained with standard techniques. [ABSTRACT FROM AUTHOR]

We report the film deposition of Poly(D,L-lactide-co-glycolide) (PLGA) particle systems by matrix assisted pulsed laser evaporation (MAPLE) technique. PLGA+polyvinyl alcohol (PVA), PLGA+PVA+ bovine serum albumin (BSA) and PLGA+PVA+chitosan (CH) nanoparticles were prepared by an oil-in-water emulsion-diffusion-evaporation method. The average diameter of PLGA particles was between 180-250 nm. The coatings were obtained by laser evaporation of frozen targets prepared by mixing appropriate PLGA aqueous suspensions and dimethyl sulfoxide (DMSO) in three ratios. Depending on the DMSO content, we deposited PLGA particles embedded into polymeric layer mainly obtained due to the entirely or partially dissolving of nanoparticles into the initial solution. In vitro results showed that the distribution and morphology of osteoblast-like SaOs-2 cells on some PLGA particle coatings were similar with that of the positive control. The purpose of this study was to develop layers of PLGA particles for local controlled drug delivery. [ABSTRACT FROM AUTHOR]