Search

Accelerator driven fast nuclear reactors cooled by lead-bismuth eutectic (LBE) are developed for transmuting long-lived radionuclides in spent nuclear fuel. Due to the nature of the coolant, operating the reactor will result in a production of 210Po by neutron capture. Understanding the behavior of this highly radiotoxic nuclide in the event of a failure of the window separating the evacuated proton beam guide from the reactor core is required for safety assessments. The present work aims at acquiring this knowledge by studying the evaporation of polonium from neutron-irradiated LBE and its deposition in a scaled down model of the beam tube. Experimental results along with Monte Carlo simulations indicate that polonium adsorbs as a single species with an adsorption enthalpy of approximately −156 kJ/mol.

Fission and fusion reactors can only play a role in the future energy landscape if they are inherently safe by design. For some reactor concepts, a major remaining issue is the undesired production of radiotoxic Po-210. To filter out the volatile Po species, information on their molecular composition is needed. An experimental characterization is very challenging due to the large required amount of radioactive Po. An alternative quantum chemistry approach was taken to predict the temperature-dependent stability of relevant diatomic Po-containing molecules. Experimental data on lighter analogue molecules was used to establish a well-founded methodology. The relative occurrence of the Po species was estimated in the cover gas of (i) the lead-bismuth eutectic coolant in the accelerator-driven MYRRHA fission reactor and (ii) the Pb-Li eutectic tritium breeder in the DEMO fusion reactor. In both systems, Po is found to occur mainly as PbPo molecules and atomic Po.

Liquid lead-bismuth eutectic (LBE) is an important candidate to become the primary coolant of future, generation IV, nuclear fast reactors and Accelerator Driven System (ADS) concepts. One of the main challenges with the use of LBE as a coolant is to avoid its oxidation which results in solid lead oxide (PbO) precipitation. The chemical equilibria governing PbO formation are well understood. However, insufficient kinetic information is currently available for the development of LBE-based nuclear technology. Here, we report the results of experiments in which the nucleation, growth and dissolution of PbO in LBE during temperature cycling are measured by monitoring dissolved oxygen using potentiometric oxygen sensors. The metastable region, above which PbO nucleation can occur, has been determined under conditions relevant for the operation of LBE cooled nuclear systems and was found to be independent of setup geometry and thus thought to be widely applicable. A kinetic model to describe formation and dissolution of PbO particles in LBE is proposed, based on Classical Nucleation Theory (CNT) combined with mass transfer limited growth and dissolution. This model can accurately predict the experimentally observed changes in oxygen concentration due to nucleation, growth and dissolution of PbO, using the effective interfacial energy of a PbO nucleus in LBE as a fitting parameter. The results are invaluable to evaluate the consequences of oxygen ingress in LBE cooled nuclear systems under normal operating and accidental conditions and form the basis for the development of cold trap technology to avoid PbO formation in the primary reactor circuit.

It is widely recognized that the control of the activity of dissolved oxygen is essential for the use of lead–bismuth eutectic (LBE) as primary coolant for nuclear systems. A lead oxide mass exchanger (PbO MX) comprised of a packed bed of lead oxide spheres is a promising solution to regulate the dissolved oxygen activity in the LBE. In order to design and operate a PbO MX properly, the dissolution kinetics of PbO in flowing LBE should be determined. A high-fidelity Computational Fluid Dynamic (CFD) model of solid-to-liquid mass transfer has been developed to determine the mass transfer coefficient of a PbO MX in flowing LBE. We validated the developed CFD model against experimental data obtained from the LBE test loop CRAFT, at SCK•CEN. The model is in good agreement with the experimental data. The effect of the channel to particle diameter ratio ( R ) on the mass transfer coefficient was evaluated by using the validated model. A mass transfer correlation for PbO MX was obtained, in terms of the Sherwood number, by fitting the simulation results for the general case of a random packed bed with a porosity of about 0.4.

Understanding polonium evaporation from lead-bismuth eutectic (LBE) is required for the design of nuclear installations that use liquid LBE as coolant or spallation target. In the present study we measured the time-dependent release of polonium from LBE samples in Ar/5 %H2 and Ar between room temperature and 500 C. Our experiments revealed that the majority of polonium in the samples evaporated according to established temperature correlations for the Henry constant of polonium in LBE. However a small fraction of polonium in the LBE behaved differently, causing a relatively large but transient polonium release at the start of evaporation experiments. We showed that this volatile fraction of polonium was located near the sample surface and was formed after prolonged exposure of the samples to air at room temperature. We speculate that the peculiar evaporation behavior of this surface polonium is caused by enrichment and association with an oxide layer. ispartof: Journal Of Radioanalytical And Nuclear Chemistry vol:302 issue:1 pages:195-200 status: published

Synchrotron small angle X-ray scattering (SAXS) was used to characterize silicalite-1 zeolite crystallization from TEOS/TPAOH/water clear sol. SAXS patterns were recorded over a broad range of length scales, enabling the simultaneous monitoring of nanoparticles and crystals occurring at various stages of the synthesis. A simple two-population model accurately described the patterns. Nanoparticles were modeled by polydisperse coreshell spheres and crystals by monodisperse oblate ellipsoids. These models were consistent with TEM images. The SAXS results, in conjunction with in situ light scattering, showed that nucleation of crystals occurred in a short period of time. Crystals were uniform in size and shape and became increasingly anisotropic during growth. In the presence of nanoparticles, crystal growth was fast. During crystal growth, the number of nanoparticles decreased gradually but their size was constant. These observations suggested that the nanoparticles were growth units in an aggregative crystal growth mechanism. Crystals grown in the presence of nanoparticles developed a faceted habit and intergrowths. In the final stages of growth, nanoparticles were depleted. Concurrently, the crystal growth rate decreased significantly.

Zeolite synthesis is driven by structure-directing agents, such as tetrapropyl ammonium ions (TPA+) for Silicalite-1 and ZSM-5. However, the guiding role of these organic templates in the complex assembly to highly ordered frameworks remains unclear, limiting the prospects for advanced material synthesis. In this work, both static ab initio and dynamic classical modeling techniques are employed to provide insight into the interactions between TPA+ and Silicalite-1 precursors. We find that as soon as the typical straight 10-ring channel of Silicalite-1 or ZSM-5 is formed from smaller oligomers, the TPA+ template is partially squeezed out of the resulting cavity. Partial retention of the template in the cavity is, however, indispensable to prevent collapse of the channel and subsequent hydrolysis.

Aggregates of nanosized crystalline units of Silicalite-1 zeolite were detected in a detailed TEM analysis of a clear solution aged for 40 months at room temperature. Inspection of the TEM images reveals the aggregation of these building units into larger crystalline zeolite particles even without heating. The smaller individual units resemble the earlier proposed nanoslab and preferentially stack along a or b crystallographic directions.

n-Alkane hydroisomerisation and hydrocracking experiments reveal that ZSM-5 materials synthesized by self-assembly of nanoslabs show different molecular shape selectivity than ZSM-5 synthesized by hydrothermal methods.