Search

Using the new polarized neutron diffraction (PND) setup at MLZ the spin reorientation transition in the magnetocaloric orthoferrite HoFeO3 was studied at different wavelength. The various experiments provided reproducible results demonstrating high reliability of the used setup. We show that during the phase transition at TSR=53 K in an external magnetic field applied along crystal c-axis, the ordered magnetic moment of the Fe sublattice rotates from the crystallographic direction b to a not just in the ab plane, but through z axis. This means that the applied field breaks the orthorhombic symmetry allowing some magnetization parallel to z within a short temperature region. Interestingly, this is the same temperature region where large magnetocaloric effect for HoFeO3 was previously reported. A general model of the magnetic structure of HoFeO3, unconstrained by the orthorhombic symmetry, would allow the magnitudes and directions of the moments on each of the 8 magnetic sublattices in the unit cell to be independent of one-another, leading to 24 independent magnetic parameters. PND measurements were used to determine the absolute sign of the Dzyaloshinskii-Moriya interaction (DMI) in the ab plane for the Fe magnetic sublattice at 65 K. DMI plays an important role in the energy balance of the system.

‘Organ-on-chip’ devices which integrate three-dimensional (3D) cell culture techniques with microfluidic approaches have the capacity to overcome the limitations of classical 2D platforms. Although several different strategies have been developed to improve the angiogenesis within hydrogels, one of the main challenges in tissue engineering remains the lack of vascularization in the fabricated 3D models. The present work focuses on the high-definition (HD) bioprinting of microvascular structures directly on-chip using two-photon polymerization (2PP). 2PP is a nonlinear process, where the near-infrared laser irradiation will only lead to the polymerization of a very small volume pixel (voxel), allowing the fabrication of channels in the microvascular range (10–30 µm in diameter). Additionally, 2PP not only enables the fabrication of sub-micrometer resolution scaffolds but also allows the direct embedding of cells within the produced structure. The accuracy of the 2PP printing parameters were optimized in order to achieve high-throughput and HD production of microfluidic vessel-on-chip platforms. The spherical aberrations stemming from the refractive index mismatch and the focusing depth inside the sample were simulated and the effect of the voxel compensation as well as different printing modes were demonstrated. Different layer spacings and their dependency on the applied laser power were compared both in terms of accuracy and required printing time resulting in a 10-fold decrease in structuring time while yielding well-defined channels of small diameters. Finally, the capacity of 2PP to create vascular structures within a microfluidic chip was tested with two different settings, by direct embedding of a co-culture of endothelial- and supporting cells during the printing process and by creating a supporting, cell-containing vascular scaffold barrier where the endothelial cell spheroids can be seeded afterwards. The functionality of the formed vessels was demonstrated with immunostaining of vascular endothelial cadherin (VE-Cadherin) endothelial adhesion molecules in both static and perfused culture.

Various biopolymers, including gelatin, have already been applied to serve a plethora of tissue engineering purposes. However, substantial concerns have arisen related to the safety and the reproducibility of these materials due to their animal origin and the risk associated with pathogen transmission as well as batch-to-batch variations. Therefore, researchers have been focusing their attention toward recombinant materials that can be produced in a laboratory with full reproducibility and can be designed according to specific needs (e.g., by introducing additional RGD sequences). In the present study, a recombinant protein based on collagen type I (RCPhC1) was functionalized with photo-cross-linkable methacrylamide (RCPhC1-MA), norbornene (RCPhC1-NB), or thiol (RCPhC1-SH) functionalities to enable high-resolution 3D printing via two-photon polymerization (2PP). The results indicated a clear difference in 2PP processing capabilities between the chain-growth-polymerized RCPhC1-MA and the step-growth-polymerized RCPhC1-NB/SH. More specifically, reduced swelling-related deformations resulting in a superior CAD-CAM mimicry were obtained for the RCPhC1-NB/SH hydrogels. In addition, RCPhC1-NB/SH allowed the processing of the material in the presence of adipose tissue-derived stem cells that survived the encapsulation process and also were able to proliferate when embedded in the printed structures. As a consequence, it is the first time that successful HD bioprinting with cell encapsulation is reported for recombinant hydrogel bioinks. Therefore, these results can be a stepping stone toward various tissue engineering applications.

The z-scan technique has become a standard method to measure 2-photon absorption (2PA) properties of materials used for 2-photon applications. Here we present a completely automated, easily tunable z;-scan setup for spectral scanning. An algorithm collecting the required laser beam parameters allows to reliably determine the optimal working window of newly synthesized 2PA photoinitiators (PI) used for two-photon polymerization (2PP) in a wide spectral range. A complete spectrum (3 measurements per wavelength in 10 nm steps) can be obtained within an hour. Matching the wavelength used for 2PP to the maximum 2PA significantly increased the 2PP performance of the system. Published by The Optical Society under the terms of the Creative Commons Attribution 4.0 License.

Gelatin is frequently used in various biomedical applications. However, gelatin is generally extracted from an animal source, which can result in issues with reproducibility as well as pathogen transmittance. Therefore, we have investigated the potential of a recombinant peptide based on collagen I (RCPhC1) for tissue engineering applications and more specifically for adipose tissue regeneration. In the current paper, RCPhC1 was functionalized with photo-crosslinkable methacrylamide moieties to enable subsequent UV-induced crosslinking in the presence of a photo-initiator. The resulting biomaterial (RCPhC1-MA) was characterized by evaluating the crosslinking behaviour, the mechanical properties, the gel fraction, the swelling properties and the biocompatibility. The obtained results were compared with the data obtained for methacrylamide-modified gelatin (Gel-MA). The results indicated that the properties of RCPhC1-MA networks are comparable to those of animal-derived Gel-MA. RCPhC1-MA is thus an attractive synthetic alternative for animal-derived Gel-MA and is envisioned to be applicable for a wide range of tissue engineering purposes.

Over the recent decades gelatin has proven to be very suitable as an extracellular matrix mimic for biofabrication and tissue engineering applications. However, gelatin is prone to dissolution at typical cell culture conditions and is therefore often chemically modified to introduce (photo-)crosslinkable functionalities. These modifications allow to tune the material properties of gelatin, making it suitable for a wide range of biofabrication techniques both as a bioink and as a biomaterial ink (component). The present review provides a non-exhaustive overview of the different reported gelatin modification strategies to yield crosslinkable materials that can be used to form hydrogels suitable for biofabrication applications. The different crosslinking chemistries are discussed and classified according to their mechanism including chain-growth and step-growth polymerization. The step-growth polymerization mechanisms are further classified based on the specific chemistry including different (photo-)click chemistries and reversible systems. The benefits and drawbacks of each chemistry are also briefly discussed. Furthermore, focus is placed on different biofabrication strategies using either inkjet, deposition or light-based additive manufacturing techniques, and the applications of the obtained 3D constructs. STATEMENT OF SIGNIFICANCE: Gelatin and more specifically gelatin-methacryloyl has emerged to become one of the gold standard materials as an extracellular matrix mimic in the field of biofabrication. However, also other modification strategies have been elaborated to take advantage of a plethora of crosslinking chemistries. Therefore, a review paper focusing on the different modification strategies and processing of gelatin is presented. Particular attention is paid to the underlying chemistry along with the benefits and drawbacks of each type of crosslinking chemistry. The different strategies were classified based on their basic crosslinking mechanism including chain- or step-growth polymerization. Within the step-growth classification, a further distinction is made between click chemistries as well as other strategies. The influence of these modifications on the physical gelation and processing conditions including mechanical properties is presented. Additionally, substantial attention is put to the applied photoinitiators and the different biofabrication technologies including inkjet, deposition or light-based technologies.

The placenta is a transient organ, essential for development and survival of the unborn fetus. It interfaces the body of the pregnant woman with the unborn child and secures transport of endogenous and exogenous substances. Maternal and fetal blood are thereby separated at any time, by the so-called placental barrier. Current in vitro approaches fail to model this multifaceted structure, therefore research in the field of placental biology is particularly challenging. The present study aimed at establishing a novel model, simulating placental transport and its implications on development, in a versatile but reproducible way. The basal membrane was replicated using a gelatin-based material, closely mimicking the composition and properties of the natural extracellular matrix. The microstructure was produced by using a high-resolution 3D printing method – the two-photon polymerization (2PP). In order to structure gelatin by 2PP, its primary amines and carboxylic acids are modified with methacrylamides and methacrylates (GelMOD-AEMA), respectively. High-resolution structures in the range of a few micrometers were produced within the intersection of a customized microfluidic device, separating the x-shaped chamber into two isolated cell culture compartments. Human umbilical-vein endothelial cells (HUVEC) seeded on one side of this membrane simulate the fetal compartment while human choriocarcinoma cells, isolated from placental tissue (BeWo B30) mimic the maternal syncytium. This barrier model in combination with native flow profiles can be used to mimic the microenvironment of the placenta, investigating different pharmaceutical, clinical and biological scenarios. As proof-of-principle, this bioengineered placental barrier was used for the investigation of transcellular transport processes. While high molecular weight substances did not permeate, smaller molecules in the size of glucose were able to diffuse through the barrier in a time-depended manner. We envision to apply this bioengineered placental barrier for pathophysiological research, where altered nutrient transport is associated with health risks for the fetus.

We present an experimental technique to determine the degenerate two-photon absorption (2PA) spectra by performing a single Z-scan using a high-spectral-irradiance white light continuum (WLC) generated by a hollow core fiber. The hollow fiber was filled with Argon (Ar) gas at a pressure of 0.6 bar and was pumped with 500 mJ, 30 fs, and 800 nm pulses. The broadband WLC pulses with 350 nm bandwidth in the range of 600-950 nm were compressed to sub-8 fs pulses. To characterize and interpret the data obtained from this method, the spectral, temporal and spatial characteristics of the WLC were first analyzed. The WLC emerging from the compressor was dispersed using a prism pair and then focused into the sample by a cylindrical lens. Since different spectral components are spatially separated, any part of the sample in the beam cross section is irradiated with almost single wavelength pulses leading to only a degenerate 2PA process. The nonlinear transmittance was then measured by a charge-coupled-device (CCD) line camera as a function of the sample position while the sample was moved along the beam direction by a motorized translation stage. In this way the Z-scans at different wavelengths in the WLC spectral range can be measured and thus the wavelength-resolved degenerate 2PA spectra can be obtained by performing a single scan using dispersive WLC. This method was verified on a well-characterized dye Rhodamine B and yield a reasonable agreement with the data found in the literature. We used this method to determine the 2PA spectra of some two-photon initiators (2PIs) developed for two-photon polymerization (2PP) based 3D micro-structuring.

The possibility of the direct encapsulation of living cells via two-photon induced photopolymerization enables the microfabrication of hydrogel scaffolds with high initial cell loadings and intimate matrix-cell contact. While highly efficient water-soluble two-photon initiators based on benzylidene ketone dyes have been developed, they exhibit considerable cyto- and phototoxicity. To address the problem of photoinitiator migration from the extracellular matrix into the cytosol, a two-photon initiator bound to a polymeric hyaluronan backbone (HAPI) was synthesized in this work. HAPI exhibited a distinct improvement of cytocompatibility compared to a reference two-photon initiator. Basic photophysical investigations were performed to characterize the absorption and fluorescence behavior of HAPI. Laser scanning microscopy was used to visualize and confirm the hindered transmembrane migration behavior of HAPI. The performance of HAPI was tested in two-photon polymerization at exceedingly high printing speeds of 100 mm s-1 producing gelatin-based complex 3D hydrogel scaffolds with a water content of 85%. The photodamage of the structuring process was low and viable MC3T3 cells embedded in the gel were monitored for several days after structuring.

The natural extracellular matrix (ECM) represents a complex and dynamic environment. It provides numerous spatio-temporal signals mediating many cellular functions including morphogenesis, adhesion, proliferation and differentiation. The cell–ECM interaction is bidirectional. Cells dynamically receive and process information from the ECM and remodel it at the same time. Theses complex interactions are still not fully understood. For better understanding, it is indispensable to deconstruct the ECM up to the point of investigating isolated characteristics and cell responses to physical, chemical and topographical cues. Two-photon polymerization (2PP) allows the exact reconstruction of cell specific sites in 3D at micro- and nanometer precision. Processing biocompatible synthetic and naturally-derived hydrogels, the microenvironment of cells can be designed to specifically investigate their behavior in respect to key chemical, mechanical and topographical attributes. Moreover, 3D manipulation can be performed in the presence of cells, guiding biological tissue formation in all stages of its development. Here, advances in 2PP microfabrication of synthetic and naturally based hydrogels are reviewed. Key components of photopolymerizable hydrogel precursors, their structure–property relationships and their polymerization mechanisms are presented. Furthermore, it is shown how biocompatible 2PP fabricated constructs can act as biologically relevant matrices to study cell functions and tissue development.

Adipose stem cells (ASCs) spheroids show enhanced regenerative effects compared to single cells. Also, spheroids have been recently introduced as building blocks in directed self-assembly strategy. Recent efforts aim to improve long-term cell retention and integration by the use of microencapsulation delivery systems that can rapidly integrate in the implantation site. Interlockable solid synthetic microscaffolds, so called lockyballs, were recently designed with hooks and loops to enhance cell retention and integration at the implantation site as well as to support spheroids aggregation after transplantation. Here we present an efficient methodology for human ASCs spheroids biofabrication and lockyballs cellularization using micro-molded non-adhesive agarose hydrogel. Lockyballs were produced using two-photon polymerization with an estimated mechanical strength. The Young's modulus was calculated at level 0.1362 +/-0.009 MPa. Interlocking in vitro test demonstrates high level of loading induced interlockability of fabricated lockyballs. Diameter measurements and elongation coefficient calculation revealed that human ASCs spheroids biofabricated in resections of micro-molded non-adhesive hydrogel had a more regular size distribution and shape than spheroids biofabricated in hanging drops. Cellularization of lockyballs using human ASCs spheroids did not alter the level of cells viability (p › 0,999) and gene fold expression for SOX-9 and RUNX2 (p › 0,195). The biofabrication of ASCs spheroids into lockyballs represents an innovative strategy in regenerative medicine, which combines solid scaffold-based and directed self-assembly approaches, fostering opportunities for rapid in situ biofabrication of 3D building-blocks.

Photografting is a method utilizing light activation for covalent incorporation of functional molecules into a polymer surface or polymer matrix. It has been widely applied as a simple and versatile method for tailoring physical–chemical properties of various surfaces. Grafting induced via multi-photon absorption provides additional advantages of spatial and temporal control of the process. Here, a novel fluoroaryl azide photografting compound (AFA) was synthesized and compared with the commercially available azide BAC-M. Using Z-scan technique, it was determined that AFA is a two-photon absorber at 798nm, whereas BAC-M is a three-photon absorber at this wavelength. Both azides were employed for 3D photografting within a PEG-based matrix using femtosecond laser pulses. Both Z-scan measurements and 3D photografting tests indicated that, the intensity threshold for nonlinear absorption and photografting process is lower for AFA. As a result the processing window of AFA is much broader than that of BAC-M. But on the other hand, since BAC-M is characterized by the three-photon absorption (3PA) process, patterns with finer features can be produced using this molecule. The choice of the appropriate compound for 3D grafting will depend on the final application and the requirements associated with the resolution and post-modification protocol.

Microneedles are small-scale devices that may be used for drug delivery and biosensing. In this study, the forces required for mechanical failure, the modes of mechanical failure, as well as the mechanisms for microneedle penetration into porcine skin were examined. Microneedles produced from the acrylate-based polymer e-Shell 200 using an indirect rapid prototyping approach involving two-photon polymerization and poly(dimethylsiloxane) micromolding were found to possess sufficient strength for penetration of porcine skin. The failure forces were an order of magnitude greater than the forces necessary for full insertion into the skin. Bending was the most common form of failure; an increasing aspect ratio and a decreasing tip diameter were associated with lower failure forces. Video captured during skin penetration revealed that microneedle penetration into the skin occurred by means of a series of insertions and not by means of a single insertion event. Images obtained during and after skin penetration confirmed microneedle penetration of skin as well as transdermal delivery of lucifer yellow dye. These findings shed insight into the mechanisms of microneedle penetration and failure, facilitating design improvements for polymer microneedles.

The natural cell environment is characterized by complex three-dimensional structures, which contain features at multiple length scales. Many in vitro studies of cell behavior in three dimensions rely on the availability of artificial scaffolds with controlled three-dimensional topologies. In this paper, we demonstrate fabrication of three-dimensional scaffolds for tissue engineering out of poly(ethylene glycol) diacrylate (PEGda) materials by means of two-photon polymerization (2PP). This laser nanostructuring approach offers unique possibilities for rapid manufacturing of three-dimensional structures with arbitrary geometries. The spatial resolution dependence on the applied irradiation parameters is investigated for two PEGda formulations, which are characterized by molecular weights of 302 and 742. We demonstrate that minimum feature sizes of 200 nm are obtained in both materials. In addition, an extensive study of the cytotoxicity of the material formulations with respect to photoinitiator type and photoinitiator concentration is undertaken. Aqueous extracts from photopolymerized PEGda samples indicate the presence of water-soluble molecules, which are toxic to fibroblasts. It is shown that sample aging in aqueous medium reduces the cytotoxicity of these extracts; this mechanism provides a route for biomedical applications of structures generated by 2PP microfabrication and photopolymerization technologies in general. Finally, a fully biocompatible combination of PEGda and a photoinitiator is identified. Fabrication of reproducible scaffold structures is very important for systematic investigation of cellular processes in three dimensions and for better understanding of in vitro tissue formation. The results of this work suggest that 2PP may be used to polymerize poly(ethylene glycol)-based materials into three-dimensional structures with well-defined geometries that mimic the physical and biological properties of native cell environments.

In the present work, the two-photon polymerization (2PP) technique was applied to develop precisely defined biodegradable 3D tissue engineering scaffolds. The scaffolds were fabricated via photopolymerization of gelatin modified with methacrylamide moieties. The results indicate that the gelatin derivative (GelMod) preserves its enzymatic degradation capability after photopolymerization. In addition, the developed scaffolds using 2PP support primary adipose-derived stem cell (ASC) adhesion, proliferation and differentiation into the anticipated lineage.

Two-photon-induced photopolymerization (2PP) has gained increased interest due to the capability of manufacturing three-dimensional structures with very high feature resolution. To assess the suitability of photopolymer systems for 2PP, methods have to be developed that allow a screening of the efficiency of monomer-initiator combinations in the context of high throughput, large processing window and geometric quality of the final parts. In this paper, a method for evaluating 2PP structures is described. For this purpose, the double-bond conversion of fabricated 2PP structures was measured giving quantifiable results about the efficiency of the photoinitiator. The method is based on local measurement of the double-bond conversion of the photopolymer using a microscope in combination with infrared spectroscopy. The obtained double-bond conversion is a measure for the efficiency of the photopolymer system (initiator in combination with monomer), and thus allows to compare different photopolymers in a quantitative way. Beside this evaluation of 2PP structures, fabrication of complex 3D structures was done to determine the limits of the 2PP technology for miscellaneous components.