Search

The aim of this paper is to assess the efficacy of non-conformal meshing in mesh-based generated reluctance network modeling. A representative semi-numerical example is introduced to demonstrate the possibilities and accuracy offered by a non-conformal meshing. In a conformal mesh, two reluctance block elements share the same branch. This makes the computation faster and more accurate but is not convenient for motion processing or mesh relaxation and it does not solve the air-gap modeling problem (rotor/stator connectivity). To solve this, different approaches are used. The interpolation approach developed in this paper aims to render motion processing independent of discretization. This approach is also applied to couple different meshes (spatial discretization) and makes it possible to connect a lumped parameter model to a meshed one. The model is divided into independent zones that are connected via the interpolation coupling. Several reluctance network (RN) non-conformal meshes are presented and global quantities are compared to a fine-meshed finite-element model. Magnetic saturation is considered in the iron parts. Comparisons are provided under open-circuit and on-load configurations for flux linkage and force. The main advantage is to overcome the limitations of generic RN for which the movement modeling requires remeshing at each position. The drawbacks of the method are the increased number of variables (additional interface nodes) and a certain loss of accuracy due to the interpolation function order. [ABSTRACT FROM AUTHOR]

This aim of this paper is to assess the efficacy of mesh-based generated reluctance network (MGRN) modeling for the performance evaluation of a permanent magnet linear machine under load conditions. In the previous publications related to the use of this modeling technique, only approach implementation under an open-circuit performance has been assessed. The MGRN approach is based on the discretization of the geometry using elementary reluctance blocks (reluctance elements). This modeling technique has been implemented in a software tool that allows the automated processing of an arbitrary geometry providing a gain in model development durations. Validation of the MGRN model has been realized by comparison with a finite element analysis (FEA). Comparisons showed that both local and global quantities evaluated by MGRN and FEA are in excellent agreement. [ABSTRACT FROM AUTHOR]

This paper discusses the construction and operating principle of an axial flux electric machine with hybrid excitation. Based on computer simulations using the Finite Element Method, an analysis was conducted with changes in the geometry of the magnetic circuit, which involves the rotation of the rotor disks relative to each other on the operating parameters of the machine. Both the generator state of operation, in the meaning of analyzing the induced voltage (adjustment at −11% ÷ +64%) and the cogging torque, and the motor state of operation, in the meaning of analyzing the ripple of the electromagnetic torque (possible reduction by almost 30%), were examined. The article concludes with observations on how the change in the angle of the rotor disks affects the efficiency of the disk machine with axial flux and hybrid excitation. [ABSTRACT FROM AUTHOR]

To further enhance the speed regulation range of the hybrid excited machine (HEM), the structure of a magnetic ring is optimized using a combination of the magnetic circuit method (MCM) and numerical analysis method in this paper, and a disc magnetic ring (DMR) is proposed. The magnetic density distribution of the proposed disc magnetic ring hybrid excited machine (DMRHEM) is compared to the radial-axial hybrid excited machine (RAHEM), and the superiority of alleviating a saturation problem in the proposed DMRHEM is determined. To improve the power density, the spoke-type permanent magnet (PM) rotor is applied. The influence of the proposed DMR on the HEM is analyzed, and the field adjustment capability of the proposed DMRHEM is better. Based on this, by combining the bypass principle, the analytical expressions for the relations between the rotor pole-pair number and the motor axial length/stator inner diameter (MAL/SID) as well as flux regulation capability are derived to further explore the superiority of the proposed DMRHEM. The influence mechanism of the rotor pole-pair number and the MAL/SID on the proposed DRMHEM is determined. The optimal MAL/SID and pole-pair number are obtained. [ABSTRACT FROM AUTHOR]

Silicon rectifier generators, which are single-excitation generators, are commonly used in vehicles. However, a traditional single-excitation generator cannot satisfy the requirements of modern vehicles due to its low efficiency, high failure rate and large excitation loss; a hybrid excitation generator is more suitable for a wide range of applications in vehicles because of its many advantages. In this study, a novel, high-efficiency and energy-saving hybrid excitation generator with a claw-pole series magnetic circuit for vehicles was designed. The magnetic circuit and principle of operation were analyzed. The structure parameters of the hybrid excitation generator were initially designed according to motor design theory. The model of the hybrid excitation generator was built based on the finite element method, and the no-load characteristic was analyzed. Furthermore, the influences of the permanent magnet thickness and core slot width on the performance of the generator were analyzed. According to the results, the structural parameters were optimized. The no-load output characteristics and load characteristics were compared between the generator and a silicon rectifier generator, and the test results show that the design, simulation and optimization methods were reasonable. This provides theoretical support and research methods for the development of a hybrid excitation generator. [ABSTRACT FROM AUTHOR]

The contactless transmission between the conductor rotor and the permanent magnet (PM) rotor of an adjustable permanent magnet coupler (APMC) provides the device with significant tolerance for alignment errors, making the performance estimation complicated and inaccurate. The first proposal of an edge coefficient in this paper helps to describe the edge effect with better accuracy. Accurate equivalent magnetic circuit (EMC) models of the APMC are established for each region. Models of magnetic flux, magnetic resistance, and eddy current density are established by defining the equivalent dimensional parameters of the eddy current circuit. Furthermore, the concept of magnetic inductance is proposed for the first time, parameterizing eddy currents that are difficult to describe with physical models and achieving the modeling of the dynamic eddy current circuit. The magnetic resistance is subdivided into two parts corresponding to the output and slip according to the power relationship. Furthermore, eddy current loss and dynamic torque models are further derived. The method proposed in this paper enables the APMC to be modeled and calculated in a completely new way. The correctness and accuracy of the model have been fully demonstrated using finite element simulation and an experimental prototype. In addition, the limitations of the proposed method and the reasons are fully discussed and investigated. [ABSTRACT FROM AUTHOR]

In this paper, a new hybrid excitation drive motor (HEDM) was proposed to solve the problem of an uncontrollable magnetic field of a permanent magnet motor. The rotor part of the motor was composed of a combined magnetic pole permanent magnet rotor and a brushless electric claw rotor, in which the combined magnetic pole permanent magnet rotor has a parallel magnetic circuit structure. According to the characteristics of the parallel rotor structure, the equivalent magnetic circuit model was established, and the no-load leakage flux coefficient of the claw pole rotor was calculated. The Taguchi method was used for objective optimization of the permanent magnet rotor structure. The distortion rate of no-load back electromotive force (EMF) was taken as the first optimization goal; the cogging torque and the average torque were taken as the second optimization goal; and the torque fluctuation coefficient was a constraint condition. The optimal parameter matching under the mixed horizontal matrix was obtained. The parameters of the claw pole were optimized by using the method of uniform variables, and the dimension parameters of the motor were obtained. Finite element analysis and prototype tests were carried out for the optimized motor structure. The rationality and feasibility of the new HEDM as a vehicle motor were verified, which provided a possibility for the application of the new energy vehicle drive motor field. [ABSTRACT FROM AUTHOR]

Aiming to design a generator with high reliability, high efficiency, and especially a constant output voltage over a wide speed range for hybrid electric vehicles (HEVs), this paper proposes a novel topology of a hybrid excitation doubly salient generator with separate windings (HEDSGSW). The topology herein utilizes a hybrid excitation type of PMs and DC windings to generate parallel magnetic circuits. In addition, PMs are embedded in the magnetic bridge to insulate the excitation windings with armature windings. This design can achieve compactness, efficiency, and especially constant output capability over a wide speed range. The geometry and flux regulation principles, including magnetic flux circuits, are elaborated. After comparing three power generation modes, the most suitable mode, namely, the doubly salient generation 2 (DSG2) mode, is confirmed to ensure a stable voltage output performance. Then, considering the non-uniformity effect of the stator and rotor slots, the no-load back electromotive force (EMF) expressions are derived based on the EMF to air-gap relative permeance method. Furthermore, a 1 kW HEDSGSW FEA model, with an output voltage of 42 V and a rated speed of 6000 rpm, is built to demonstrate the effectiveness of the proposed method. Finally, the operating properties of the HEDSGSW, such as no-load characteristics and adjustment characteristics, are analyzed to further verify the rationality of its magnetic flux circuit and the flexibility of the excitation regulation capability. [ABSTRACT FROM AUTHOR]

Aiming at the problem of uncontrollable magnetic field of permanent magnet generators, a new hybrid excitation generator (HEG) with parallel magnetic circuit is proposed. The HEG consists of combined permanent magnet rotor (PMR) and brushless electric excitation rotor (EER). The PMR has surface-mounted and embedded magnets. The PMR provides the main air gap field, and the brushless EER is used to adjust the air gap field. The operating principle and electromagnetic design scheme of the proposed generator are given in detail. Besides, the matching with two different types of rotors and the flux regulation characteristics is analyzed by using the finite element method. Finally, the output performance of the proposed generator including no-load and load characteristics and output voltage are tested. The results show that the two different types of rotors can be matched efficiently and operated reliably. The internal magnetic flux is easy to adjust in both directions, and the proposed HEG can output stable voltage in the range of wide speed and load. [ABSTRACT FROM AUTHOR]

Summary: The switched reluctance motor (SRM) has the high level of vibration and noise, whose application is greatly limited in many fields. In this article, a novel stator for a SRM is designed to reduce torque ripple and is suitable for one‐directional or low‐speed reverse rotation. On the one hand, a shoe is added to the stator pole side in the rotating forward direction from the completely unaligned to the aligned position. On the other hand, a slot is set on the top of stator tooth. First, causes of vibration and torque ripple are analyzed. Second, it is indicated by the equivalent magnetic circuit (EMC) method that the air gap permeability of the model with the single‐sided pole shoe is larger than that of the conventional model in the nonoverlapping region between the stator and rotor. The influences of the angle and height of shoe on the air gap magnetic density, radial force, and torque ripple are analyzed. Third, the results from EMC method show that the radial force can be reduced by opening a slot at the top of stator pole arc. The width and depth of slot which has effect on the radial force and torque ripple are analyzed. Finally, finite element analysis results show that the decreases of 34.52% for the radial force wave peak and 43.39% for the torque ripple are achieved at the cost of a decrease of 8.54% for the average torque of the single‐sided pole and the slot model of the stator pole compared with the conventional model. Some experiments for the two prototypes verify that the torque ripple and radial force can be reduced by adopting the new model. [ABSTRACT FROM AUTHOR]

In this article, a Hybrid Excitation Synchronous Machine (HESM) is optimally designed for a specified Hybridization Ratio (HR). A new formulation of the design problem is proposed to be tackled by the Non-dominated Sorting Genetic Algorithm II (NSGA-II), while minimizing the material cost. This formulation includes a more comprehensive explanation of the key concept, HR, which considers the soft and hard saturation effects in the HESM design. The HESM model is based on a 3D nonlinear Magnetic Equivalent Circuit (MEC). For faster convergence, the number of design variables is reduced using two statistical analyses, namely Analysis of Level and Analysis of Variance (ANOVA). A HESM is optimally designed for HR = 0.5 and validated by a commercial Finite Element Analysis (FEA) software. [ABSTRACT FROM AUTHOR]

Summary: This article proposes an analytical model based on magnetic equivalent circuit for a transverse‐flux permanent magnet machine (TFPMM). Taking into account, the magnetic saturation in iron parts of the machine, the proposed method is capable of calculating the performance parameters of the machine such as flux density, flux linkage, cogging torque, back‐EMF and its harmonic contents with high accuracy. In order to evaluate the accuracy of proposed model, performance parameters of a TFPMM obtained analytically are compared to those achieved by three‐dimensional finite element method (3‐D FEM). A preliminary optimisation based on the proposed analytical modelling is presented to show suitability of the approach in performance parameter optimisation of TFPMM. In comparison to 3‐D FEM, the proposed model introduces less computational time, while the accuracy remains approximately the same. The results show that the proposed approach can be used during design stage and optimisation of the transverse flux machine as a simple, fast and accurate alternative to the precise but time consuming and tedious 3‐D FEM. [ABSTRACT FROM AUTHOR]

A novel parallel-hybrid dual permanent magnet (PM) machine topology with both enhanced torque density and improved flux weakening capability is proposed for electric vehicle propulsion in this paper. The key is to artificially construct the harmonics diversity with a single-layer concentrated armature winding in the stator and thus simultaneously couple the armature field with the excitation field produced by slot PM, rotor PM, and stator dc source, respectively. Enhanced torque density is obtained in this new topology due to the symmetrical flux-modulation effect between dual PM sources. Moreover, benefiting from a parallel excitation characteristic of hybrid magnetic circuit, the demagnetization risk is significantly mitigated for slot PM source and thus an extended flux weakening range is obtained. In this paper, the proposed new topology and its design mechanism are investigated, along with its electromagnetic performance evaluated based on finite-element analysis. Further, some leading design parameters are analyzed and determined to provide a design guideline for the proposed new topology. Finally, a prototype is built and fully tested. Relevant experimental results agree well with the finite-element predication. [ABSTRACT FROM AUTHOR]

Aiming at the disadvantages of large leakage flux and low magnetic flux density of radial magnetic circuit and tangential magnetic circuit, a new type of permanent magnet (PM) rotor with parallel tangential and radial magnetic circuits is proposed. Based on Ohm's law and Kirchhoff's law of magnetic circuits, equivalent magnetic circuits for rotor poles are developed. The structure parameters of the generator are preliminarily determined. At the same time, by means of the Taguchi method and employing finite element analysis, the rotor poles of generator are optimized to improve air gap magnetic density, the cogging torque, and the distortion of back-EMF waveform. Finally, the validity of proposed design methods is validated by the analytical and experimental results. [ABSTRACT FROM AUTHOR]

In this study, a new sensitivity analysis based on non‐linear varying‐network magnetic circuit (VNMC) method is proposed for an outer‐rotor I‐shaped permanent magnet flux‐switching motor. By integrating concept of sensitivity analysis into the non‐linear VNMC method, the whole design efficiency can be improved effectively by using the comprehensive sensitivity method and sequential non‐linear programming algorithm. In the optimisation process, two design objectives are selected, including machine output torque and torque ripple. Based on the sensitivity analysis, the parameters possessing the significant influence on the design objectives can be selected purposely, thus the overall amount of calculation is obviously reduced. After the determination of the sensitive parameters, the rest of optimisation can be realised efficiently by the non‐linear VNMC method. Finally, a prototype motor is manufactured and tested. Both theoretical analysis and experimental results confirm the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

This study presents magnetic equivalent circuit (MEC) model of ring winding axial flux machine (AFM). The ring winding AFM is a new permanent magnet topology that presents many advantages like reliability, simple construction, low cost and ease of increasing pole and phase numbers. For optimal design of this new type of machine, a fast and accurate performance analysis tool is needed. In this regard, MEC model of the ring winding AFM is proposed. It is shown that the developed MEC model of the ring winding AFM provides very fast solution, yet accurate results compared with three‐dimensional finite‐element model (3D FEM). The proposed MEC model considers 3D geometry, magnetic saturation, leakage fluxes and rotor position. Furthermore, this study provides equations to consider fringing flux between arc segmented surface mounted permanent magnets and stator teeth. Experimental and 3D FEM results are employed to show the validity of the proposed MEC model. [ABSTRACT FROM AUTHOR]

Recently, studies on the hybrid excitation synchronous motor using permanent magnet (PM) together with field windings have been actively conducted. In this regard, this paper seeks to investigate brushless hybrid excitation synchronous motors with improved rotors. The design was performed using an equivalent magnetic circuit to determine the best of four possible different structures. Using a finite-element analysis (FEA), the back electromotive force (EMF) per PM usage and the phase back EMF of each type were calculated and compared, and the design that can best reduce costs and increase torque density was determined. A detailed design of one of the four structures with excellent characteristics was performed, and the associated characteristics and problems were verified. An improved rotor structure was proposed to resolve the identified problems and improve performance. The phase back EMF and the total harmonic distortion of the phase back EMF, cogging torque, load torque, and torque ripple of the improved rotor structure were verified through the application of the FEA. In addition, the prototype motor was fabricated, and a no-load test was conducted to compare the test results and analysis results on the phase back EMF. The reliability of the analysis results was confirmed by comparison between test results and analysis results on the input current, line to line voltage, and efficiency under the same output conditions through the load test. [ABSTRACT FROM AUTHOR]

This paper suggests a possible design of variable flux motor for adjustable speed operation. A method to calculate electrical parameters to meet variable speed conditions is suggested, and the basic motor shape is decided using the relationships between the calculated electrical parameters and motor geometry. The difference between coercivity of two types of magnet is used to control the flux. To prevent irreversible demagnetization of low-coercivity magnet, the approximate shape of magnet is decided by calculating the operating point of the magnet using an equivalent magnetic circuit. The optimum shape of magnet considering the nonlinear characteristics is suggested using a finite-element method. To validate the design, magnetizing/demagnetizing, and load operation tests are conducted. [ABSTRACT FROM PUBLISHER]

Hybrid-excited permanent magnet (PM) machines utilise the coordinated operation between the PM and the field excitation current. To enhance the effectiveness of the field excitation current, iron flux bridges are applied to hybridexcited switched-flux PM machines. This study proposes a new control strategy in which the d-axis current is utilised, while the field excitation current is controlled towards zero rather than negative in the flux-weakening mode. These reference currents are determined by the voltage error regulation method. The special magnetic circuit can effectively reduce the d-axis flux-linkage by either partially short-circuiting the PM flux via the iron bridge or removing the field excitation current. The proposed method exhibits advantages, such as highly enhanced torque response in the constant torque region, extended speed range, robustness against machine parameters, and higher efficiency in fluxweakening region. The feasibility of the proposed method is verified by detailed experimental results. [ABSTRACT FROM AUTHOR]

Hybrid‐excited permanent magnet (PM) machines utilise the coordinated operation between the PM and the field excitation current. To enhance the effectiveness of the field excitation current, iron flux bridges are applied to hybrid‐excited switched‐flux PM machines. This study proposes a new control strategy in which the d‐axis current is utilised, while the field excitation current is controlled towards zero rather than negative in the flux‐weakening mode. These reference currents are determined by the voltage error regulation method. The special magnetic circuit can effectively reduce the d‐axis flux‐linkage by either partially short‐circuiting the PM flux via the iron bridge or removing the field excitation current. The proposed method exhibits advantages, such as highly enhanced torque response in the constant torque region, extended speed range, robustness against machine parameters, and higher efficiency in flux‐weakening region. The feasibility of the proposed method is verified by detailed experimental results. [ABSTRACT FROM AUTHOR]

Most of the electrical machines designed to have their stators on the outside and their rotors on the inside. However, it was noticed that the shaft fills a relatively high volume inside the machine without producing any torque. That means there is a wasted volume within the machine and this volume does not produce any torque. From this point of view, there are some trends in designing and building electrical machines to have their rotors outside the machine and their stators inside the machine. Here the example used for the machines using those designs is the permanent magnet (PM) machine, which is an electrical machines designed by the two different methods, inner and outer rotors to be used in many applications such as wind turbines and electric vehicle wheel motors. This paper is dedicated to prove that the external rotor permanent magnet machine is preferred for some significant reasons. The paper uses two approaches to demonstrate that. The first approach is using the geometrical volume of each machine to compare the torque capabilities in case of two possible topologies of the PM machines. The second approach is to compare the PM machine with another type of electrical machine, that has the same magnetic circuit topology and the rotor can be inside and outside as well. [ABSTRACT FROM AUTHOR]

This study presents a novel switched reluctance machine (SRM) with modular E‐core stators and multi‐layer common rotors for high reliability applications. The stator is composed of six independent modular E‐cores with the windings wound around the yoke of the E‐cores. The rotor consists of three magnetically independent common rotors which are place in the same shaft without any angular shift. The equivalent magnetic circuit (EMC) models of this new SRM at the aligned and unaligned positions are described. To evaluate the motor performance, two types of analysis, namely, approximate simplified two‐dimensional (2D) model and 3D model finite‐element analysis (FEA) have been utilised. The 2D FEA static and dynamic results are compared with 3D FEA results. Furthermore, comparisons between the novel modular SRM and a conventional 6/4 SRM are made. Finally, a prototype of this modular SRM has been fabricated and tested in the laboratory. Comparison between FEA and EMC analysis for flux linkage are made and compared with measured characteristics. The simulated and measured phase currents and average torque are also presented and compared to verify the analytical and simulation results. [ABSTRACT FROM AUTHOR]

In this paper, the 12-slot/4-pole (12/4) synchronous reluctance motor (SynRM) with concentrated windings is proposed for low-cost hybrid vehicles. The non-linear magnetic equivalent circuit (MEC) model of the 12/4 SynRM is built to obtain the main electromagnetic characteristics such as coil flux, inductances, torque, etc. The magnetic saturation is also counted in by the MEC. Results calculated by MEC are validated by 2D finite element analysis (FEA). Then, aiming at larger average torque, lower torque ripple and lower total harmonic distortion (THD) in phase voltage, the parameter optimization method of the SynRM is proposed based on the Taguchi method and the MEC model. The proposed Taguchi-MEC method enables a fast optimization with satisfactory accuracy. Finally, the motor prototype is manufactured, and experimental validations are carried out. [ABSTRACT FROM AUTHOR]

This paper deals with the modeling by reluctant network of a linear actuator used for electromagnetic valves. Flux paths through the magnetic circuit of the actuator are firstly provided and analyzed. Then, equivalent reluctant branches corresponding to each flux path are defined. The so established model is resolved to calculate the actuator force applied on valves and obtained results are compared to ones carried out using a 2D finite element calculation. [ABSTRACT FROM AUTHOR]

In this study, hybrid excitation doubly salient machines (HEDSMs) with parallel excitation structures are introduced. The three types of main poles in the HEDSMs are described and researched, respectively. A 30/20-pole HEDSM is analysed by the magnetic circuit means. Regulation performance of the air-gap fluxes of different main poles is presented. The expression of the total air-gap flux shows the ideal linear relationship between the total air-gap flux and the field excitation ampere-turns. The finite element analysis also verifies the perfect effect of the field control. And the flux line plots and no-load electromagnetic force (EMF) waveforms are presented. The experimental EMF waveforms and no-load characteristic curve are coincident with the simulation results. [ABSTRACT FROM AUTHOR]

Magnetic flux distributions of the permanent magnet (PM) section and the homopolar induction (HI) section in a hybrid excitation synchronous generator (HESG) are calculated by using the finite element method (FEM). The influences of the axial-length ratio of the two sections on the back EMF, inductance, and terminal characteristics of the PM section, the HI section, and the HESG are analyzed. The prototype experiments have verified the validity of the calculation and analysis processes. The studies on the HI section have shown the following: 1) The operating air-gap flux distribution along the axial direction is uneven; 2) there is an approximate linear relationship between the radial component average of the operating air-gap flux density and the axial length; 3) a quadratic relationship between the back EMF and the axial length exists; and 4) it is necessary to compute and optimize the axial-length ratio of the PM section and HI section to increase the output voltage and improve the terminal characteristics of the HESG. [ABSTRACT FROM AUTHOR]

Hybrid-excited machines utilize the synergies of permanent magnet (PM) and wound field machines. Flux-switching PM machines have emerged as an attractive machine type due to the fact that the excitation sources are located in the stator allowing a simple robust rotor whilst providing high torque density. This paper proposes topologies of hybrid-excited flux-switching PM machines incorporating iron flux bridges to enhance the effectiveness of the field coil excitation. A simple lumped parameter magnetic circuit model is developed to predict the effect of adjusting various parameters. Two-dimensional finite-element analysis has also been used to predict the machine performance, while a prototype machine has been built and tested to validate the predicted results. [ABSTRACT FROM AUTHOR]

This paper presents a Hybrid Excited Double-Sided Linear Flux Switching Machine (HEDSLFSM) with a crooked tooth modular stator. Generally, the conventional stators are made of a full-length iron core, increasing manufacturing costs and iron losses. Higher iron losses result in lower efficiency and lower overall performance. A U-shaped modular stator with a crooked tooth is used to lower iron consumption and increase the machine's efficiency. Ferrite magnets are used to replace rare earth magnets, which also reduces the machine cost. Two DC excitation windings are used above and below the ferrite magnet to reduce the PM volume. 2D electromagnetic performance analysis is done to observe the key performance indices. Geometric optimization is used to optimize the Split Ratio (S.R), DC winding slot area (DCw), and AC winding slot area (ACw). Stator Tooth Width (STW), space between the modules (S.S.), and crooked angle (α) are optimized through JMAG in-built Genetic Algorithm (G.A.) optimization. High thrust force density and modular stator make it a good candidate for long-stroke applications like railway transits. The thermal analysis of the machine is performed by FEA analysis and then validated by 2D LPMC (Lumped Parametric Magnetic Equivalent Circuit) model. Both analyses are compared, and an error percentage of less than 4% is achieved. [ABSTRACT FROM AUTHOR]

The analytical model of a permanent magnet eddy current coupler (PMECC) is mainly used for evaluation of its characteristics and the initial optimization of design. Based on the equivalent magnetic circuit method, this paper carries out analytical modeling for four typical PMECCs composed of surface-mounted and interior permanent magnet, slotted and non-slotted conductor rotors, which provides a theoretical basis for the subsequent research in this paper. The basic electromagnetic characteristics of the PMECCs are investigated by the established analytical model. Simultaneously, the analytical results about permeance, flux density, torque and power are verified by FEA simulation. The analysis results show that the slotted CR will obtain a much higher power density, and the iron loss mainly exists in the CRs. In addition, the analytical and FEA results agree well, which proves the reliability of the proposed, nearly unified analytical model. [ABSTRACT FROM AUTHOR]

Flux-switching permanent magnet (FSPM) motors have a doubly salient structure, the magnets being housed in the stator and the stator winding comprising concentrated coils. They have attracted considerable interest due to their essentially sinu- soidal phase back electromotive force (EMF) waveform. However, to date, the inherent nature of this desirable feature has not been investigated in detail. Thus, a typical three-phase FSPM motor with 12 stator teeth and ten rotor poles is considered. It is found that, since there is a significant difference in the magnetic flux paths associated with the coils of each phase, this results in harmonics in the coil back EMF waveforms being cancelled, resulting in es- sentially sinusoidal phase back EMF waveforms. In addition, the influence of the rotor pole-arc on the phase back EMF waveform is evaluated by finite-element analysis, and an optimal pole-arc for minimum harmonic content in the back EMF is obtained and verified experimentally. [ABSTRACT FROM AUTHOR]

A nonlinear adaptive lumped parameter magnetic circuit model is developed to predict the electromagnetic performance of a flux- switching permanent-magnet machine. It enables the air-gap field distribution, the back-electromotive force (back-EMF) waveform, the winding inductances, and the electromagnetic torque to be calculated. Results from the model are compared with finite-element predictions and validated experimentally. The influence of end effects is also investigated, and optimal design parameters, such as the rotor pole width, the stator tooth width, and the ratio of the inner to outer diameter of the stator, are discussed. [ABSTRACT FROM AUTHOR]

In recent years, innovative magnetic materials have been introduced in the field of electrical machines. In the ambit of soft magnetic materials, laminated steels guarantee good robustness and high magnetic performance but, in some high-frequency applications, can be replaced by Soft Magnetic Composite (SMC) materials. SMC materials allow us to reduce the eddy currents and to design innovative 3D magnetic circuits. In general, SMCs are characterized at room temperature, but as electrical machines operate at high temperature (around 100 °C), an investigation analysis of the temperature effect has been carried out on these materials; in particular, three SMC samples with different binder percentages and process parameters have been considered for magnetic and energetic characterization. [ABSTRACT FROM AUTHOR]

Interior Permanent Magnet Synchronous Machine (IPMSM) are high torque density machines that usually work under heavy load conditions, becoming magnetically saturated. To obtain properly their performance, this paper presents a node mapping criterion that ensure accurate results when calculating the performance of a highly saturated IPMSM via a novel magnetic reluctance network approach. For this purpose, a Magnetic Circuit Model (MCM) with variable discretization levels for the different geometrical domains is developed. The proposed MCM caters to V-shaped IPMSMs with variable magnet depth and angle between magnets. Its structure allows static and dynamic time stepping simulations to be performed by taking into account complex phenomena such as magnetic saturation, cross-coupling saturation effect and stator slotting effect. The results of the proposed model are compared to those obtained by Finite Element Method (FEM) for a number of IPMSMs obtaining excellent results. Finally, its accuracy is validated comparing the calculated performance with experimental results on a real prototype. [ABSTRACT FROM AUTHOR]