Search

Solid polymer electrolytes (SPEs) have the potential to meet evolving Li‐ion battery demands, but for these electrolytes to satisfy growing power and energy density requirements, both transport properties and electrochemical stability must be improved. Unfortunately, improvement in one of these properties often comes at the expense of the other. To this end, a "hybrid aqueous/ionic liquid" SPE (HAILSPE) which incorporates triethylsulfonium‐TFSI (S2,2,2) or N‐methyl‐N‐propylpyrrolidinium‐TFSI (Pyr1,3) ionic liquid (IL) alongside H2O and LiTFSI salt to simultaneously improve transport and electrochemical stability is studied. This work focuses on the impact of HAILSPE composition on electrochemical performance. Analysis shows that an increase in LiTFSI content results in decreased ionic mobility, while increasing IL and water content can offset its impact. pfg‐NMR results reveal that preferential lithium‐ion transport is present in HAILSPE systems. Higher IL concentrations are correlated with an increased degree of passivation against H2O reduction. Compared to the Pyr1,3 systems, the S2,2,2 systems exhibit a stronger degree of passivation due to the formation of a multicomponent interphase layer, including LiF, Li2CO3, Li2S, and Li3N. The results herein demonstrate the superior electrochemical stability of the S2,2,2 systems compared to Pyr1,3 and provide a path toward further enhancement of HAILSPE performance via composition optimization. [ABSTRACT FROM AUTHOR]

Solid electrolyte interphase (SEI) formation and H2O activity reduction in Water‐in‐Salt electrolytes (WiSE) with an enlarged stability window of 3.0 V have provided the feasibility of the high‐energy‐density aqueous Li‐ion batteries. Here, we extend the cathodic potential of WiSE by rationally controlling intermolecular interaction and interphase chemistry with the introduction of trimethyl phosphate (TMP) into WiSE. The TMP not merely limits the H2O activity via the strong interaction between TMP and H2O but also contributes to the formation of reinforced SEI involving phosphate and LiF by manipulating the Li+ solvation structure. Thus, water‐tolerance LiMn2O4 (LMO)||Li4Ti5O12 (LTO) full cell with a P/N ratio of 1.14 can be assembled and achieve a long cycling life of 1000 times with high coulombic efficiency of >99.9 %. This work provides a promising insight into the cost‐effective practical manufacture of LMO||LTO cells without rigorous moisture‐free requirements. [ABSTRACT FROM AUTHOR]

Water‐in‐salt (WIS) electrolytes using super‐concentrated organic lithium (Li) salts are of interest for aqueous Li‐ion batteries. However, the high salt cost, high viscosity, poor wettability, and environmental hazards remain a great challenge. Herein, we present a localized water‐in‐salt (LWIS) electrolyte based on low‐cost lithium nitrate (LiNO3) salt and 1,5‐pentanediol (PD) as inert diluent. The addition of PD maintains the solvation structure of the WIS electrolyte, improves the electrolyte stability via hydrogen‐bonding interactions with water and NO3− molecules, and reduces the total salt concentration. By in situ gelling the LWIS electrolyte with tetraethylene glycol diacrylate (TEGDA) monomer, the electrolyte stability window can be further expanded to 3.0 V. The as‐developed Mo6S8|LWIS gel electrolyte|LiMn2O4 (LMO) batteries delivered outstanding cycling performance with an average Coulombic efficiency of 98.53 % after 250 cycles at 1 C. [ABSTRACT FROM AUTHOR]

Abstract: Solid electrolytes have been considered as a promising approach for Li dendrite prevention because of their high mechanical strength and high Li transference number. However, recent reports indicate that Li dendrites also form in Li2S‐P2S5 based sulfide electrolytes at current densities much lower than that in the conventional liquid electrolytes. The methods of suppressing dendrite formation in sulfide electrolytes have rarely been reported because the mechanism for the “unexpected” dendrite formation is unclear, limiting the successful utilization of high‐energy Li anode with these electrolytes. Herein, the authors demonstrate that the Li dendrite formation in Li2S‐P2S5 glass can be effectively suppressed by tuning the composition of the solid electrolyte interphase (SEI) at the Li/electrolyte interface through incorporating LiI into the electrolyte. This approach introduces high ionic conductivity but electronic insulation of LiI in the SEI, and more importantly, improves the mobility of Li atoms, promoting the Li depositon at the interface and thus suppresses dendrite growth. It is shown that the critical current density is improved significantly after incorporating LiI into Li2S‐P2S5 glass, reaching 3.90 mA cm−2 at 100 °C after adding 30 mol% LiI. Stable cycling of the Li‐Li cells for 200 h is also achieved at 1.50 mA cm−2 at 100 °C. [ABSTRACT FROM AUTHOR]

The electrochemical stability window of solid electrolyte is overestimated by the conventional experimental method using a Li/electrolyte/inert metal semiblocking electrode because of the limited contact area between solid electrolyte and inert metal. Since the battery is cycled in the overestimated stability window, the decomposition of the solid electrolyte at the interfaces occurs but has been ignored as a cause for high interfacial resistances in previous studies, limiting the performance improvement of the bulk-type solid-state battery despite the decades of research efforts. Thus, there is an urgent need to identify the intrinsic stability window of the solid electrolyte. The thermodynamic electrochemical stability window of solid electrolytes is calculated using first principles computation methods, and an experimental method is developed to measure the intrinsic electrochemical stability window of solid electrolytes using a Li/electrolyte/electrolyte-carbon cell. The most promising solid electrolytes, Li10GeP2S12 and cubic Li-garnet Li7La3Zr2O12, are chosen as the model materials for sulfide and oxide solid electrolytes, respectively. The results provide valuable insights to address the most challenging problems of the interfacial stability and resistance in high-performance solid-state batteries. [ABSTRACT FROM AUTHOR]

[Display omitted] Pre-lithiation is critical for improving the energy density of lithium-ion batteries (LIBs) in practical applications. The pre-lithiation of the high-capacity anode with a large surface area enhances the initial coulombic efficiency (ICE) by compensating the lithium loss from the formation of solid electrolyte interphase (SEI). However, pre-lithiation also affects cycle life, which has been paid little attention to. Here, we first discuss the impact of pre-lithiation on the cycling stability of the full cells, which is closely related to anode material, the degree of pre-lithiation, and the stability of SEI. Then we provide suggestions on how to achieve both high energy density and long cycle life by pre-lithiation. The understanding of the correlation between pre-lithiation and cycling stability sheds light on achieving the optimal performance of lithium-ion batteries from pre-lithiation technology. [ABSTRACT FROM AUTHOR]