Search

The soil sorptivity, S , which is defined as a measure of the capacity of a porous medium to absorb or desorb liquid by capillarity, is commonly estimated under laboratory conditions from upward infiltration measurements. The objective of this work is to compare different methods to estimate S from a single upward infiltration curve obtained from both theoretical and experimental soils. An additional analysis of the influence of synthetic infiltration noise on the estimation of S was also performed on the theoretical soils. Five different methods were compared: Short Time model for horizontal infiltration (ST), the Cumulative Linearization method (CL) and the Differentiated Linearization (DL) linear regressions models, Short-time (SIM) methods that use the simplified Haverkamp et al. (1994) model, and Complete-time (CIM) upward infiltration method that uses the quasi-analytical Haverkamp et al. (1994) function. Since finite soil columns were considered, the saturated hydraulic conductivity needed to estimate S with the Haverkamp et al. (1994) model was calculated from an overpressure step at the end of the water absorption process, using the Darcy's law. The methods were contrasted on four theoretical and six sieved experimental soils, ranging from sand to clay textures. Although all methods showed acceptable estimates of S on clean theoretical upward infiltration curves, the ST, SIM and CIM were the methods that gave significant ( p < 0.001) regression analysis on noisied infiltration curves, and only SIM and CIM presented a relative error < 1%. From these results we can conclude that although acceptable approaches of S were obtained with the simplest ST method, the CIM procedure was the most accurate method to estimate S in both clean and noised theoretical and experimental upward infiltration curves. [ABSTRACT FROM AUTHOR]

Summary In-situ measurements of soil hydraulic properties on covered soil surfaces (i.e. vegetated or residue covered surfaces) are of paramount importance in many agronomic or hydrological researches. These soil parameters are commonly estimated with the tension infiltrometry technique. This paper presents a portable and modified design of the hood infiltrometer (MHI) that, unlike to the original hood infiltrometer, allows estimating the soil hydraulic properties from the transient cumulative infiltration curve. The MHI consists of a water-supply reservoir attaches to a hat-shaped base placed on the soil surface. The base of the hat is closed by a system of sticks and a malleable material ring. To test the viability of this new design, the hydraulic conductivity ( K s ) estimated with MHI in a loam soil using the multiple head approach was compared to the corresponding values calculated from the transient infiltration curve analysis. Next, the MHI was tested on three different soils at saturated conditions, and the sorptivity ( S ) and K s estimated by the transient infiltration curve analysis were compared to the corresponding values obtained with a disc infiltrometer (DI). An additional field experiment was performed to compare the hydraulic properties measured with MHI on a bare soil and a soil covered with plants. Results demonstrated that this design allows hermetically closing the base of the hat without disturbing the soil surface. The K s estimated with the multiple head approach was not statistically different ( p = 0.61) to that obtained with the transient infiltration curve analysis. No significant differences between the K s ( p = 0.66) and S ( p = 0.50) values estimated with DI and MHI were observed. The S values measured with MHI on the covered soil surface were significantly higher than that measured on the adjacent bare soil. These results indicate that MHI can be a viable alternative to estimate the hydraulic properties of covered soils from the measured transient infiltration curve. [ABSTRACT FROM AUTHOR]

• A method to estimate θ s , α , n and K s from an upward infiltration is presented. • The influence of θ s, θ r and h i , on the α , n and K s optimization was studied. • It was applied to 50 mm high undisturbed cores under different soil management. • θ s and h i affected α , n and K s , and h i should be located the d θ dh ≈ 0 region. • It was sensible to different texture and structure due to the soil management. Estimation of the α and n van Genuchten (1980) parameters and the saturated hydraulic conductivity, K s , of undisturbed soil samples is critical for realistic water flow simulations in the vadose zone. Given the Latorre and Moret-Fernández (2019) method, which allows estimating K s , α and n from the inverse analysis of a single upward infiltration, the objective of this work is to advance on the theoretical understanding of this method and to apply it on undisturbed soil cores. To this end, the influence of the saturated, θ s , and residual, θ r , water content and initial soil tension, h i , on the α , n and K s optimization was first studied on synthetic soils. A procedure to simultaneously estimate θ s , α , n and K s , which consisted on optimizing α , n and K s for a range of θ s values, was proposed. To this end, α , n and K s were optimized leaving each θ s as a fixed value. The method was next applied to experimental curves measured from sieved and undisturbed soil cores of 50 mm high and diameter, sampled the last ones from three fields with different management: bare vs. under plant soil; agricultural soil under conservation vs. conventional tillage; and overburden soil from mine vs. topsoil formed by the original soil. Results showed that θ s had an important effect on α , n and K s optimization, where the minimum error within the selected θ s interval corresponded to the theoretical θ s. An important effect of h i on the optimization was also observed. However, this influence was omitted by using a h i value located in the θ r region, where d θ dh ≈ 0. Under this assumption, θ r only affected the θ s optimization, which value varied with θ r. A robust relationship (R2 = 0.99; p < 0.0001) was found between theoretical and optimized θ s , K s and α and n calculated for the synthetic soils. Thus, the method allowed estimating four of the five van Genuchten (1980) parameters. An absolute minimum was also observed when the method was applied on experimental infiltration curves. The θ s measured gravimetrically on the undisturbed samples was, on average, 8.1% higher than the optimized one. Overall, the method allowed detecting significant differences (p < 0.05) in hydraulic properties between bare and under plant soils and among tillage treatments. The large variability found in the mine's soils prevented to find significant differences within this scenario. [ABSTRACT FROM AUTHOR]

Summary Based on the analysis of Haverkamp et al. (1994), this paper presents a new technique to estimate the soil hydraulic properties (sorptivity, S , and hydraulic conductivity, K ) from the full-time cumulative infiltration curves. The proposed method, which will be named as the Numerical Solution of the Haverkamp equation (NSH), was validated on 12 synthetic soils simulated with HYDRUS-3D. The K values used to simulate the synthetic curves were compared to those estimated with the NSH method. A procedure to detect and remove the effect of the contact sand layer on the cumulative infiltration curve was also developed. A sensitivity analysis was performed using the water level measurement as uncertainty source and the procedure was evaluated considering different infiltration times and data noise (e.g. air-bubbling in the infiltrometer). The good correlation between the K used in HYDRUS-3D to model the infiltration curves and those obtained by the NSH method ( R 2 = 0.98) indicates this technique is robust enough to estimate the soil hydraulic conductivity from complete infiltration curves. The numerical procedure to detect and remove the influence of the contact sand layer on the K and S estimates resulted to be robust and efficient. A negative effect of the curve infiltration noise on the K estimate was observed. The results showed that infiltration time was an important factor to estimate K . Smaller values of K or lower uncertainty required longer infiltration times. In a second step, the technique was tested in field conditions on 266 different soils at saturation conditions, using a 10 cm diameter disc infiltrometer. The NSH method was compared to the standard differentiated linearization procedure (DL), which estimates the hydraulic parameters using the simplified Haverkamp et al. (1994) equation, valid only for short to medium times. Compared to DL, NSH was considerably less affected by the infiltration bubbling and the contact sand layer, and allowed more robust estimates of K and S . Although comparable S values were obtained with both methods, the NSH technique, which is not limited to short times, resulted in more accurate and robust estimates for K . This paper demonstrates the NSH method is a significant advance to estimate of the soil hydraulic properties from the transient water flow. [ABSTRACT FROM AUTHOR]