Search

In the present research, glass and basalt fiber-reinforced polypropylene composites' behaviour in quasi-static and dynamic conditions is studied. Composites were fabricated by vacuum assisted Compression molding method. Composites failure under quasi-static tension and compressive conditions was studied along with its failure behaviour under low-velocity impact and super-sonic shock loading under dynamic conditions. The study results showed that basalt fiber-reinforced polypropylene (Basalt/PP) composite's tensile and compressive strength is higher than glass fiber-reinforced polypropylene (Glass/PP). The Basalt/PP showed no penetration against low velocity impact (LVI) with negligible deformations till 50 J. However, the Glass/PP perforated at 50 J with various failure patterns occurring at back side. The fiber-matrix interface adhesion plays an important role in super-sonic shock loading by absorbing shock wave energy due to ductile nature of polypropylene and the two composites absorbed energy via matrix and fibers failure, no brittle failure of laminates occurred under shock loading. [ABSTRACT FROM AUTHOR]

• High hardness steel (HHS) sheet with UHMWPE composite backing were tested against a hardened steel core projectile. • The projectile core was eroded by the HHS sheet and stopped in UHMWPE composite. • It is observed that only a core eroded to a certain length and weight by armor system can be defeated. • In numerical modeling core failure strain was determined from the residual weight of cores. • The numerical model can be used to evolve armor design. Thin high hardness steel sheets can be an alternative to expensive ceramic armor systems designed to defeat hardened core projectiles. A thin high hardness steel sheet backed with UHMWPE fiber-reinforced composite was ballistically tested against a 7.62 × 39 mm hardened steel core projectile in a single-stage gas gun. Thin steel sheets of 530 BHN hardness were adhesively bonded with UHMWPE fiber-reinforced composite to fabricate armor plates. Armor plates were able to defeat the projectile showing considerable potential. Tensile strength of steel sheet and UHMWPE-fiber reinforced ply was also determined. A detailed numerical simulation of the impact event was also performed to understand the phenomenon of defeat and penetration in greater detail. The numerical model was calibrated from the recovered projectile's core after the ballistic test. [ABSTRACT FROM AUTHOR]

Quasi-static tensile test of UHMWPE fiber-reinforced composite laminate is challenging to perform due to low interlaminar shear strength and low coefficient of friction. Tensile tests proposed in the literature were conducted and limitations associated with each method led to the evolution of a new method. Tensile test of single-ply was realized as the best representative of tensile strength of a composite than tensile test of UHMWPE laminate. A fixture was developed for single-ply tests which increased friction and provided the mechanical constraint to slipping. The fixture is easy to fabricate and has provided repeatable results for eight grades of UHMWPE fiber-based (0/90) fabrics. Reported tensile strengths are in quite high range of 900–1500 MPa. • Ballistic composites are quite different from structural composites. • Tensile strength difficult to determine with standard methods. • All available methods tested for efficacy. • A new method is suggested for efficient testing. • Properties of wight commercial grades determined by suggested method. [ABSTRACT FROM AUTHOR]

• Vacuum compression moulded Basalt-Polyeteherimide (PEI) composites manufacturing. • Optimization of Basalt-PEI composite manufacturing moulding parameters. • Basalt-PEI composite under quasi-static and dynamic high strain rate loading. • Elastic recovery of Basalt-PEI composite can help in reflecting the blast wave. High temperature blast and ballistic resistant light weight fibre reinforced plastic composites are very much in demand. Accordingly, the present investigation is focused on the quasi-static and high strain rate behaviour of Basalt/Polyetherimide (PEI) composite. Nine different types of composite samples were fabricated by compression moulding. The moulding pressures and temperatures were varied in the range of 15–25 bars and 325 °C−375 °C, respectively. Quasi-static testing was done at the rate of 3 mm/min to establish the optimum moulding parameters. High strain rate compression tests in the strain rate range of 900/s−3200/s were performed on the optimum moulded composite specimens. High strain rate testing revealed that 40 layered Basalt/PEI composite moulded at 25 bar pressure and 350 °C attained highest stress of 932 MPa whereas, the same was found to attain 446 MPa under quasi-static loading conditons. Thus, establishing the rate depedency of Basalt/PEI composite. Damage studies revealed that Basalt/PEI undergoes brittle damage, typically resulting in shear plane angle of 42°−45°. SEM micrographs revealed brittle fibre failure and matrix free fibre bundles, indicating the importance of process parameter optimiation. [ABSTRACT FROM AUTHOR]