Search

Flexible electronic devices with skin-like properties are hailed as revolutionary for the development of next-generation electronic devices, such as electric-skin and humanoid robotics. Graphene is intrinsically flexible due to its structural thinness in nature and are considered next-generation materials for wearable electronics. These devices usually experience a large mechanical deformation in use so as to achieve intimate conformal contact with human skin and to coordinate complex human motions, while heat dissipation has been a major limitation when the device is under a large mechanical strain. Unlike the small deformation (<1%) induced by intrinsic material factors such as lattice mismatch between material components in devices, a large mechanical deformation (>1%) by an external loading condition could lead to apparent changes to global geometric shapes and significantly impact thermal transport. In this study, we investigated the thermal conductivities of graphene under several large mechanical strains: 2.9%, 4.3%, and 6.1%. We used a refined opto-thermal Raman technique to characterize the thermal transport properties and discovered the thermal conductivities to be 2092 ± 502, 972 ± 87, 348 ± 52, and 97 ± 13 W/(m K) for the relaxed state, 2.9%, 4.3%, and 6.1% tensile strain, respectively. Our results showed a significant decreasing trend in thermal conductivities with an increasing mechanical strain. The findings in this study reveal new thermal transport mechanisms in 2D materials and shed light on building novel flexible nanoelectronic devices with enhanced thermal management. [ABSTRACT FROM AUTHOR]

Bond line thickness (BLT) is an essential parameter of thermal conductive composite gels as the thermal interface material (TIM). Extensive research has been performed on designing next-generation TIMs with high thermal conductivity; however, it remains elusive how to link laboratory measurements and the theoretically predicted BLT. Here, we propose a new model to estimate BLT based on a rheological property, in which the TIM is assumed to be a simple power law fluid. To avoid the unrealistic situation of the BLT tending to zero, we introduce a decaying exponential function to describe the influence from fillers during the lid attach process and rebuild the force balance equation. Compared with previously reported models, the theoretical prediction BLT based on the proposed model is in good agreement with the experimental data. Our model has a guiding significance in predicting the BLT, which may help to optimize the thermal performance of TIMs. [ABSTRACT FROM AUTHOR]

The two-dimensional laser-based Ångstrom method measures the in-plane thermal properties for anisotropic film-like materials. It involves periodic laser heating at the center of a suspended film sample and records its transient thermal response by infrared imaging. These spatiotemporal temperature data must be analyzed to extract the unknown thermal conductivity values in the orthotropic directions, an inverse parameter fitting problem. Previous demonstration of the metrology technique used a least-squares fitting method that relies on numerical differentiation to evaluate the second-order partial derivatives in the differential equation describing transient conduction in the physical system. This fitting approach is susceptible to measurement noise, introducing high uncertainty in the extracted properties when working with noisy data. For example, when noise of a signal-to-noise ratio of 10 is added to simulated amplitude and phase data, the error in the extracted thermal conductivity can exceed 80%. In this work, we introduce a new alternative inverse parameter fitting approach using physics-informed neural networks (PINNs) to increase the robustness of the measurement technique for noisy temperature data. We demonstrate the effectiveness of this approach even for scenarios with extreme levels of noise in the data. Specifically, the PINN-approach accurately extracts the properties to within 5% of the true values even for high noise levels (a signal-to-noise ratio of 1). This offers a promising avenue for improving the robustness and accuracy of advanced thermal metrology tools that rely on inverse parameter fitting of temperature data to extract thermal properties. [ABSTRACT FROM AUTHOR]

The binary high-pressure phase diagram of the Ta–Sb system was constructed for the first time in this study, utilizing the evolutionary algorithm USPEX and density functional theory (DFT). Ten pressurized dynamically and mechanically stable or metastable novel phases of Ta–Sb were discovered, including I4/mmm-TaSb2, P4/nmm-TaSb, P-3-Ta2Sb7, I4/mmm-Ta2Sb3, P-4m2-Ta7Sb, Pm-3-Ta7Sb, Pmm2-Ta15Sb, P4/nmm-TaSb3, I4/mmm-Ta3Sb4, and I4/mmm-Ta2Sb5. The compounds P-4m2-Ta7Sb and Pmm2-Ta15Sb exhibit promising characteristics as non-centrosymmetric superconductors (NCSs), with their superconducting critical temperature (TC) being 3.831 and 3.221 K, respectively. The application of pressure tuning is predicted to transform the topological characteristics of P4/nmm-TaSb, causing it to transition from a topological insulator state to a Dirac semimetal state and ultimately reverting back to a topological insulator state. Therefore, the P4/nmm-TaSb compound is considered a promising candidate to investigate topological and superconducting excitations. Moreover, the mechanical and thermal properties of Ta–Sb binary phases were also investigated. The thermal conductivity of I4/mmm-TaSb2, P4/nmm-TaSb, and P4/nmm-TaSb3 all surpasses 20 W m−1 K−1 at 1000 K, showcasing their excellent thermal conductivity properties. The present study addresses the research gap concerning high-pressure structures in the Ta–Sb binary system, thereby offering valuable insights for the design and development of intermetallic compounds within this binary system. [ABSTRACT FROM AUTHOR]

Owing to the unique asymmetric geometry, Janus monolayer compounds exhibit various exotic thermal properties and have promising applications in thermal management. In this study, we combine machine learning potentials and the phonon Boltzmann transport equation to perform a comparative study of the thermal transport properties in Janus XBAlY (X = Se, S, Te; Y = S, Se, O; X ≠ Y) monolayers. Our findings unveil a thermal conductivity (κ p) ranking as SeBAlS > TeBAlO > SBAlSe, contradicting the conventional expectation that a higher κ p is typically observed when the average atomic mass is smaller. At room temperature, the κ p of SeBAlS is 174 Wm−1 K−1, which is 4.8 times that of SBAlSe when considering three-phonon scattering processes. Moreover, the consideration of four-phonon scatterings does not alter such ranking. The anomalous κ p phenomenon was explained through a detailed analysis of the phonon–phonon scattering mechanism, phonon bandgap, phonon anharmonicity, and chemical bond strength. This study highlights the intricate relationship between atomic mass, bonding characteristics, and thermal properties, offering insights for designing Janus materials with tailored thermal conductivity. [ABSTRACT FROM AUTHOR]

Hafnia (HfO2) is a potential candidate for the high-k gate dielectrics in next-generation high-power electronics. Its thermal transport properties, which determine the performance of these related high-power electronics, are critical while rarely investigated. Here, the thermal transport properties of HfO2 in a wide temperature range of 300–2000 K with a phase transition between monoclinic and tetragonal phases at ∼1765 K, are systematically studied based on the temperature-dependent effective potential landscapes with both propagating and coherence thermal transport considered. It is found that the cage-like structure of monoclinic HfO2 results in the avoid crossing in the phonon band structures, which increases the three-phonon scattering largely. Some phonon modes with significant scattering matrix can have relatively larger 3ph and 4ph scattering rates in tetragonal HfO2. Consequently, the thermal conductivity of HfO2 is only 11.95–1.72 W/mK at 300–2000 K. Our results further show that propagating phonon channels dominate the thermal transport in HfO2 and contribute at least 70% to the total thermal conductivity. The rest of the thermal conductivity of HfO2 results from the coherence thermal transport channels, which is caused by the overlap of phonons. Four-phonon scatterings are found to be significant for the thermal transport in tetragonal HfO2, which can result in a thermal conductivity reduction of ∼50%. Our results here advance the understanding of the thermal transport in HfO2, which may benefit the performance optimization of HfO2-related electronics. [ABSTRACT FROM AUTHOR]

The lattice thermal conductivity (LTC) of Ga 2 O 3 is an important property due to the challenge in the thermal management of high-power devices. In this work, we develop machine-learned neuroevolution potentials (NEPs) for single-crystalline β - Ga 2 O 3 and κ - Ga 2 O 3 and demonstrate their accuracy in modeling thermal transport properties. Combining NEP-driven homogeneous non-equilibrium molecular dynamics simulations with tensor analysis, we determine the spatial distributions of LTCs for two Ga 2 O 3 crystals, showing dissimilar thermal behaviors. Specifically, β - Ga 2 O 3 shows isotropic thermal transport properties, with the LTCs along [100], [010], and [001] directions being predicted to be 10.3 ± 0.2 , 19.9 ± 0.2 , and 12.6 ± 0.2 W/(m K), respectively, consistent with previous experimental measurements. For κ - Ga 2 O 3 , our predictions suggest nearly isotropic thermal transport properties, with the LTCs along [100], [010], and [001] being estimated to be 4.5 ± 0.1 , 3.9 ± 0.1 , and 4.0 ± 0.1 W/(m K). The reduced LTC of κ -Ga 2 O 3 vs β -Ga 2 O 3 stems from its restricted low-frequency phonons up to 5 THz. Furthermore, we find that the β phase exhibits a typical temperature dependence slightly stronger than ∼ T − 1 , whereas the κ phase shows a weaker temperature dependence, ranging from ∼ T − 0.5 to ∼ T − 0.7 . [ABSTRACT FROM AUTHOR]

The carbon nano-peapod is a representative structure with interlayer van der Waals (vdW) interactions, in which encapsulated fullerene molecules play a critical role in modulating the transport properties of the carbon nanotubes (CNTs). In particular, their influence on the thermal transport characteristics has been the focal point of considerable attention. In this study, we trained an accurate machine learning potential for fullerene-encapsulated CNTs based on the efficient NEP model to investigate their thermal properties. Using equilibrium molecular dynamics simulation along with the spectral decomposition method for thermal conductivity, we find that the thermal conductivity of fullerene-encapsulated CNTs is roughly 55 % lower than that of empty CNTs, aligning with experimental observations for CNT bundles with fullerene encapsulation [Kodama et al., Nat. Mater. 16, 892 (2017)]. The research suggests that weak vdW interactions between both the fullerene and CNTs, as well as between fullerene molecules themselves, hinder phonon propagation. The encapsulated fullerene contributes to an increase in phonon scattering within the CNTs, ultimately leading to a reduction in thermal conductivity. We utilized machine learning potential to investigate the structure of fullerene-encapsulated CNTs and their heat transport property. This approach provides valuable insights for performance research of complex systems featuring interlayer vdW interactions. [ABSTRACT FROM AUTHOR]

When an impurity with a light mass is inserted into a crystal, it can undergo a high-frequency oscillation referred to as a local vibrational mode (LVM). A Fermi resonance may occur between the LVM and lower-frequency modes of the defect. The LVM may also interact with phonons or the electromagnetic field. Understanding these interactions can help model and control diffusion, defect reactions, and thermal conductivity. LVMs have been probed in semiconductors using pressure and alloying as experimental parameters, resulting in anticrossing between localized and extended vibrational modes. These types of vibrational interactions could play an important role in the stability and thermal properties of organic–inorganic hybrid semiconductors. The coupling between an LVM and electromagnetic wave yields an "LVM polariton," an excitation that has significant vibrational and electric-field amplitudes. [ABSTRACT FROM AUTHOR]

Time-domain thermoreflectance (TDTR) and frequency-domain thermoreflectance techniques have been widely used to measure thermal properties. However, the existence of the metal sensor brings some limitations to the experimental measurement, such as temperature limits, disability to measure low in-plane thermal conductivity, in situ measurement cannot be achieved, etc. This paper proposes a transducerless time-domain thermoreflectance method to measure in- and cross-plane thermal conductivity of nanofilms, in which the optical absorption depth and thermal conductivity tensor are considered to establish a new differential equation that can describe the heat conduction process in multilayer structures. This thermal model can also calculate the effects of spot ellipticity and spot offset distance. Then, the analytical solution and relative deviation of this new model and the surface heat flow boundary model used in conventional TDTR are compared by calculating the phase signals. In terms of experimental measurement, this model is successfully used to derive cross- and in-plane thermal conductivity of PdSi and IrNiTa amorphous alloy nanofilms without a metal sensor. [ABSTRACT FROM AUTHOR]

ABSTRACT Low‐temperature densification of alumina using calcium vanadate (CaV2O6, CV) having a similar dielectric constant as a liquid‐forming additive has been studied. The alumina‒CV composites containing 20‒40 vol.% CV achieve ∼94% of theoretical density at low temperatures of 1100°C‒900°C by liquid‐phase sintering. A reduction in the average size of grains from .87 to .42 µm with a surge in CV amount from 20 to 40 vol.% is observed. The permittivity decreases from 9.2 to 8.90, and the dielectric loss increases from 2.154 × 10‒3 to 4.761 × 10‒3 when the amount of CV in the alumina‒CV composite rises from 20 to 40 vol.%. The temperature coefficient of resonance frequency, thermal expansion coefficient, and thermal conductivity of the alumina‒CV composites are observed in the ranges of ‒54 to ‒72 ppm °C‒1, 6.94‒7.32 ppm °C‒1, and 13.78‒8.02 W m‒1 K‒1, respectively. The compatibility of the composites with Ag for low‐temperature co‐fired ceramics (LTCC) application is established through co‐sintering and energy‐Dispersive X‐ray spectroscopy line spectra analysis. The low‐temperature densification, acceptable range of dielectric and thermal properties, and silver compatibility make the alumina‒CV composite a candidate for LTCC application. [ABSTRACT FROM AUTHOR]

New C/SiC composites with continuous fibers were produced through impregnation of carbon fiber preforms and consolidation by hot pressing. The resulting sintered material was investigated as a potential target for nuclear applications, such as radioisotope production. Desired properties include high porosity and high thermal conductivity to allow isotope release from the targets while working at high temperature. To this end, porosimetry and thermal and mechanical characterizations were conducted up to 1250°C. It was shown that the addition of fibers resulted in high porosity, about 40%, while maintaining a very high thermal conductivity, 40 W/m∙K at 1250°C, a value particularly attractive for the intended application. Emissivity at 1250°C was 0.76, compressive strength at room temperature was 134 MPa, and flexural strength passed from about 90 MPa before thermal conductivity measurements to 50 MPa after the tests. [ABSTRACT FROM AUTHOR]

During the machining of Inconel 718 using SiAlON ceramics, the tool life can be significantly influenced by diffusion wear. To investigate this crucial wear behavior, this study focuses on the thermochemical interactions in the diffusion couple between SiAlON ceramics and Inconel 718 superalloy. So, we examine the microstructural characteristics and phase formation behavior in the reacted layer between these two materials. The interfaces between these two materials exhibit distinguishable elemental contrasts and phase formations. Particularly, the phases indicate vitrification or devitrification in the diffusion layer, influenced by the chemical composition. This issue in the diffusion couple was analyzed with thermophysical properties using light flash analysis (LFA). After, it was confirmed that the vitrification of the diffusion layer can be induced by the conduction behavior of heat trapped between SiAlON and Inconel 718 during supercooling. These characterizations verify that the devitrification of the welding layer (diffusion layer), resulting from the reaction between SiAlON ceramics and Inconel 718 superalloy, can depend on the thermal conductivity of the prepared ceramics. Furthermore, we discovered a possibility that this could contribute to improving tool performance by suppressing diffusion wear. [ABSTRACT FROM AUTHOR]

The continuous updating and iteration of electronic devices brings about a significant accumulation of heat. It is urgent to enhance the thermal properties of polymer‐based composites to alleviate the heat dissipation problem in the microelectronics industry. In this paper, the hot drawing process was introduced to increase the crystallinity of ultra‐high molecular weight polyethylene (UHMWPE) fiber and improve its thermal conductivity. The ultra‐high molecular weight polyethylene fiber/epoxy resin (UHMWPE fiber/Epoxy) composites with high thermal conductivity were prepared by compositing UHMWPE fiber with epoxy resin under vacuum conditions. Due to the good crystallinity of the UHMWPE fiber (86%), an efficient thermal conduction path is provided for phonons in the axial direction along the fibers. The results show that the thermal conductivity of the composites reaches a maximum of 3.51 W/mK (in‐plane), which is 17.47 times higher than that of the epoxy resin (0.19 W/mK). The thermography pictures indicate that the composites have better heat transfer capacity with an increase in the draw ratio (λ). In addition, the composites also have the characteristics of low density and low electrical conductivity. These researches will provide a new idea for the preparation of all‐polymer composites with high thermal properties. Highlights: A hot drawing process was introduced to increase the crystallinity of UHMWPE fiber for improving thermal conductivity.High crystallinity facilitates the reduction of phonon scattering and the transmission of thermal energy by phonons.The obtained polymer composites exhibit an ultra‐high in‐plane thermal conductivity. [ABSTRACT FROM AUTHOR]

Carbon fiber reinforced epoxy resin matrix composite is one of the most important composite materials in the world. Many researchers have conducted a lot of research on epoxy resin matrix systems in recent years, mainly to improve the problem with the short curing time of the matrix system and epoxy resin's high viscosity. The final aim is to enhance various aspects of composites' performance and optimize the production process. A new type of water dispersed epoxy resin matrix system is investigated in this paper and the target is to optimize the mechanical, thermal, and electrical performances of the composites with the water dispersed epoxy resin matrix by varying different doping particles and different resin/catalyst ratios. Through a series of experiments, it is evident that varying the ratio of resin to catalyst in the matrix system will not significantly improve the mechanical as well as thermal properties of the composites. However, increasing the amount of catalyst in the matrix system can greatly improve the electrical properties of its composite samples. In addition to this, the addition of doping particles to the matrix systems has the effect of slightly enhancing the tensile modulus, thermal conductivity, and electrical conductivity of their composites. Highlights: A new water‐dispersed epoxy resin matrix system improves processing technology.Increasing amount of catalyst in the matrix system improves electrical resistivity.Adding particles to matrix systems has a slight effect on different properties. [ABSTRACT FROM AUTHOR]

Fluorine rubber (FKM) stands as a pivotal sealing material extensively employed in aerospace and nuclear industries. However, its efficacy will be seriously affected by ionizing radiation. Enhancing its radiation resistance becomes imperative to uphold the stability and safety of associated equipment. This study introduced hexagonal boron nitride (h‐BN) into the FKM as radioprotective fillers through mechanical blending. The interfacial interaction between matrix and h‐BN, the mechanical performances, thermal properties, and radiation stability of composites were systematically examined. Noteworthy findings highlight the presence of robust interaction forces between h‐BN and the matrix, leading to increased crosslink density and improved mechanical properties. The tensile strength of composite with 10 phr fillers (BN/FKM‐10) increased by 30% compared to that of pure FKM. Simultaneously, the introduction of h‐BN greatly enhanced thermal conductivity and radiation stability. The absorbed dose required to achieve a 50% reduction in elongation at break of BN/FKM‐10 surpassed that of FKM by 1.69 times. These results underscore the potential of incorporating h‐BN to simultaneously enhance the mechanical performance, thermal property, and radiation resistance of fluorine rubber. Highlights: The chemical interaction force between h‐BN and FKM was confirmed.FKM composites tensile strength was enhanced by h‐BN as an additive crosslinker.The incorporation of h‐BN improves FKM composites thermal conductivity.The radiation resistance of FKM composites has been improved with h‐BN. [ABSTRACT FROM AUTHOR]

Highlights Increasing miniaturization and integration of microelectronic devices have led to an unprecedented attention on heat dissipation and signal transmission of electronic equipment. However, the mostly used method to enhance the thermal conductivity of polymers by adding thermally conductive fillers usually results in the increase of dielectric constant (Dk). It was still challenging to synergistically achieve low Dk and high thermal conductivity of polymer‐matrix composites. Herein, hydroxylated boron nitride nanosheet (BNNS‐OH) with a high yield of 35.67% was prepared by the liquid ultrasonic exfoliation under the assistance of sodium cholate (SC), and grafted with (1H,1H,2H,2H‐perfluorodecyl) trimethoxy silane to prepare fluorinated boron nitride nanosheets (F‐BNNS), which can uniformly disperse in liquid silicone rubber (LSR) and reduce the Dk of LSR composites. The thermal conductivity of LSR composites with 20 wt% F‐BNNS reached 0.489 W·m−1·K−1, showing an increase of 307.35% in comparison with pure LSR (0.12 W·m−1·K−1). Meantime, the Dk of as‐obtained LSR/F‐BNNS (20 wt%) composites is reduced from 3.4 to 2.6, and the dielectric loss (Df) is less than 0.012. The facile and rational design of fluorinated BNNS offers a new insight for the high‐end electronic packaging materials. A new method of exfoliation and fluorinated treatment of h‐BN was proposed. The LSR composites achieved an ultralow Dk of 2.63 via fluorinated BNNS. Thermal conductivity of LSR composites increased by 307.35% than pure LSR. [ABSTRACT FROM AUTHOR]

Here, we propose a sensing scheme based on an all-dielectric metamaterial with the smooth reflection and transmission spectral lines in 10-60THz, and verify the applications of the measuring the resonance characteristics of Xuan paper samples. The reflection and thermal conductivity of Xuan paper samples enhance with the concentration of alum water increasing and weaken due to the thickness increasing. These results provide a solid foundation for this metamaterials in measuring the reflective and thermal resonance properties of Xuan paper samples. [ABSTRACT FROM AUTHOR]

This work addresses the problem of obtaining of Ca 3 Co 4 O 9+δ -based ceramics with enhanced thermoelectric performance. Phase-inhomogeneous layered calcium cobaltite ceramics with cationic nonstoichiometry were prepared by solid-state reactions method and a field assisted sintering technology (FAST). Comprehensive experimental characterizations were conducted on the prepared bulk samples, focusing on their phase composition, as well as thermal (including thermal expansion, thermal diffusivity, and thermal conductivity), electrical (encompassing electrical conductivity and the Seebeck coefficient), and functional properties (such as power factor and figure-of-merit). The FAST technique allowed to obtain ceramics with low porosity and high electrical conductivity, which increased as the Ca:Co ratio within the samples decreased, while sample phase inhomogeneity considerably increased the Seebeck coefficient. The best thermoelectric performance was demonstrated for cationic nonstoichiometric Ca 3 Co 4.4 O 9+δ , which power factor and figure-of-merit values at 825 °C reached 427 μW⋅m−1⋅K−2 and 0.146, respectively. • Ca 3 Co 4 O 9+δ -based ceramics prepared by field assisted sintering technology possessed low porosity and high conductivity. • Electrical conductivity of bulk samples increased at decreasing Ca:Co ratio. • Phase inhomogeneity of prepared ceramics increased the Seebeck coefficient. • Ca 3 Co 4.4 O 9+δ ceramics showed the best thermoelectric performance. [ABSTRACT FROM AUTHOR]

In the present research, the impacts of Ce additions at various concentrations (0, 1.0, 3.4, and 4.0 wt.%) on the evolution of the microstructure, mechanical properties, and thermal conductivity of as-cast and as-extruded Mg-3Sn alloys were investigated. The findings demonstrate that adding Ce caused the creation of a new ternary MgSnCe phase in the magnesium matrix. Some new Mg17Ce2 phases are generated in the microstructure when Ce levels reach 4%. The thermal conductivity of the Mg-3Sn alloy is significantly improved due to Ce addition, and the Mg-3Sn-3.4Ce alloy exhibits the highest thermal conductivity, up to 133.8 W/(m·K) at 298 K. After extrusion, both the thermal conductivity and mechanical properties are further improved. The thermal conductivity perpendicular to the extrusion direction of Mg-3Sn-3.4Ce alloy could achieve 136.28 W/(m·K), and the tensile and yield strengths reach 264.3 MPa and 227.2 MPa, with an elongation of 7.9%. Adding Ce decreases the dissolved Sn atoms and breaks the eutectic α-Mg and Mg2Sn network organization, leading to a considerable increase in the thermal conductivity of as-cast Mg-3Sn alloys. Weakening the deformed grain texture contributed to the further enhancement of the thermal conductivity after extrusion. [ABSTRACT FROM AUTHOR]

Thermal and electrical properties were investigated for five nominally phase‐pure high entropy carbide ceramics. The compositions (Hf0.2Nb0.2Ta0.2Ti0.2Zr0.2)C, (Cr0.2Hf0.2Ta0.2Ti0.2Zr0.2)C, (Hf0.2Mo0.2Ta0.2Ti0.2Zr0.2)C, (Hf0.2Ta0.2Ti0.2W0.2Zr0.2)C, and (Hf0.2Mo0.2Ti0.2W0.2Zr0.2)C were synthesized by carbothermal reduction of oxides. The thermal diffusivity and heat capacity were measured from room temperature to 1800°C. The room temperature thermal conductivity ranged from 5.1 W/mK for (Hf0.2Mo0.2Ti0.2W0.2Zr0.2)C to 9.0 W/mK for (Cr0.2Hf0.2Ta0.2Ti0.2Zr0.2)C. The thermal conductivity increased over the temperature range with maximum conductivities of 19.6 W/mK measured for (Hf0.2Mo0.2Ta0.2Ti0.2Zr0.2)C to 29.7 W/mK for (Cr0.2Hf0.2Ta0.2Ti0.2Zr0.2)C at 1800°C. The electron contribution to thermal conductivity calculated from measured electrical resistivity varied from 41% to 52% of the total thermal conductivity. The tungsten and molybdenum containing compositions had higher phonon contributions while the niobium and chromium containing compositions had nearly equal electron and phonon contributions to thermal conductivity. [ABSTRACT FROM AUTHOR]

YBCO openwork structures were 3D-printed as cuboids with 4.5 × 4.5 × 2 mm dimensions and various filling degrees. Initial pycnometric data showed a slight variation in specimen densities (∼6.153 g/cm3), proving the production process uniformity. The consistency of YBCO superconducting phase (Y-123) was confirmed by Raman spectroscopy, X-ray diffraction and X-ray absorption spectroscopy. Microstructural and chemical homogeneity was proven by scanning electron microscopy with microprobe analysis. Transport (electrical and thermal) measurements accompanied by simulations of magnetic flux density at the produced structures revealed that they are heavily dependent of filling ratio and geometry. Additionally, this work proves that the 3D printing is an excellent method of fabricating high-quality superconducting structures of desired shapes accordingly to applicational demands. [ABSTRACT FROM AUTHOR]

High-entropy ceramics have garnered significant attention in recent years owing to their exceptional properties and structural diversity. In this work, single-phase medium/high entropy ceramics, namely (Ca 0.2 Sr 0.4 Ba 0.4)(Zr 0.5 Ti 0.5)O 3 and (Ca 0.2 Sr 0.4 Ba 0.4)(Zr 0.1 Ti 0.9)O 3 , were successfully designed and prepared utilizing Spark Plasma Sintering (SPS). A comprehensive investigation was conducted into the phase structure, microscopic morphology, dielectric properties, and thermal behavior of these ceramics. It was observed that all ceramics maintained a cubic perovskite structure (space group: Pm 3 ‾ m), and the introduction of multi-element doping rendered them more stable across a wide frequency and temperature range. Notably, (Ca 0.2 Sr 0.4 Ba 0.4)(Zr 0.5 Ti 0.5)O 3 exhibited remarkably low dielectric loss (0.0001 at 1 kHz) at room temperature, along with excellent dielectric temperature stability (25–400 °C). By reducing the zirconium concentration in (Ca 0.2 Sr 0.4 Ba 0.4)(Zr 0.1 Ti 0.9)O 3 , a slight decrease in dielectric temperature stability was observed (25–350 °C); however, it demonstrated lower thermal conductivity (0.41 W/(m·K), 1200 °C) and maintained good high-temperature stability. The discovery highlights the promising practicality of both ceramics for high-temperature dielectric applications. [ABSTRACT FROM AUTHOR]

Aluminum nitride (AlN), prized for its high thermal conductivity and electronic insulating properties, finds widespread use in electronic applications, particularly as a substrate material. However, its relatively low fracture toughness limits its application. In this study, to enhance both the thermal and mechanical properties of AlN ceramics, we thoroughly investigate the microstructure, thermal, and mechanical properties of self-reinforced AlN ceramics fabricated by spark plasma sintering, with self-reinforcement achieved through the integration of AlN whiskers within the AlN matrix. Unlike previous studies utilizing conventional pressureless sintering with limited sintering conditions, this work employs spark plasma sintering with a wide range of temperatures (1600–1900 °C) and holding times (10–30 min), providing a comprehensive understanding of the sintering behavior. Microstructural features, observed through optical and scanning electron microscopy, reveal distinct toughening mechanisms via crack deflection and branching, with a maximum 20% enhancement. The self-reinforced AlN ceramics exhibit remarkable improvements in thermal conductivity, reaching up to 150 W m−1 K−1, surpassing reported values for spark plasma-sintered AlN ceramics. Adding AlN whiskers enhances the thermal and mechanical properties of AlN simultaneously, particularly at 1800 °C for 10 min with controlled grain size and nicely integrated AlN whiskers. This work not only contributes valuable insights into the complex relationship between processing parameters, microstructure, and resulting thermal and mechanical properties but also highlights the enhanced thermal and mechanical properties of self-reinforced AlN ceramics. [ABSTRACT FROM AUTHOR]

Multi-layered graphene and graphene oxide have been used as reinforcements in nanodevices and nanocomposites due to their extraordinary mechanical and thermal properties. However, compared to graphene, graphene oxide has a lower Young's modulus and lower thermal conductivity. Nanodevices and nanocomposites based on multi-layered graphene and graphene oxide require different mechanical properties and thermal conductivity. This study employed molecular dynamics simulation to investigate 10 models of multi-layered graphene and graphene oxide (in the form of different layer arrangements) in single, double, and triple layers. The results showed that an increase in the number of graphene oxide layers leads to irregularities in the nanosheets, resulting in decreased thermal conductivity (by 64.4%) of the nanosheets decreases. Furthermore, the greater number of graphene layers in multi-layer nanosheets resulted in an increase in Young's modulus (by 79.3%) and tensile strength (by 73.7%). Moreover, the arrangement of graphene and graphene oxide is a crucial factor that can significantly impact the mechanical properties and thermal conductivity of the models. Moreover, an increase in temperature can lead to a decrease in Young's modulus of multilayered nanosheets. Increasing the number and size of graphene layers enhances both the ultimate tensile strength and the critical energy release rate. [ABSTRACT FROM AUTHOR]

Ternary half-Heusler (HH) alloys are under intense investigations recently towards achieving high thermoelectric (TE) figure-of-merit (ZT). Of particular interest is the ZrNiPb-based HH alloy, where an optimal value of ZT ~ 0.7 at 773 K has been achieved by co-doping Sn and Bi at Pb site. In this work, we identify an excellent ZT of 1.3 in ZrNi1+xPb0.38Sn0.6Bi0.02 (x = 0.03, at 773 K) composite alloy. This is achieved by synergistic modulation of electronic as well as thermal properties via introduction of minor phase of full-Heusler (FH) in the HH matrix through compositional tuning approach. These Ni-rich ZrNi1+xPb0.38Sn0.6Bi0.02 (0 ≤ x ≤ 0.07) alloys were synthesized via energy efficient and time-curbed techniques that involved Arc melting followed by consolidation via spark plasma sintering. These alloys were characterized by XRD and SEM, which show formation of nanocomposites comprising of HH matrix phase and FH secondary minor phases. Enhancement in ZT is mainly attributed to a synchronized increase in power factor (~42%) and ~25% decrease in its thermal conductivity. Here, TE compatibility factor (S) was also calculated for all samples. The value of |S| ~ 2.7 V−1 (at 773 K) is observed for x = 0.03, which is ~17% higher than bare HH composition (x = 0.0). The theoretically calculated TE device efficiency of best-performing sample ZrNi1.03Pb0.38Sn0.6Bi0.02 is estimated to be η ~ 13.6%. Our results imply that deliberately controlled fine tuning in compositions of HH compounds through compositional tuning approach would lead to novel off-stoichiometric HH phases with enhanced ZT value for efficient TE device fabrication. [ABSTRACT FROM AUTHOR]

Copyright of Journal of Engineering (17264073) is the property of Republic of Iraq Ministry of Higher Education & Scientific Research (MOHESR) and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

The energy consumption of buildings presents a significant concern, which has led to a demand for materials with better thermal performance. Thermal conductivity (TC), among the most relevant thermal properties, is essential to address this demand. This study introduces a methodology integrating a Multilayer Perceptron (MLP) and a Generative Adversarial Network (GAN) to predict the TC of concrete based on its mass composition and density. Three scenarios using experimental data from published papers and synthetic data are compared and reveal the model's outstanding performance across training, validation, and test datasets. Notably, the MLP trained on the GAN-augmented dataset outperforms the one with the real dataset, demonstrating remarkable consistency between the model's predictions and the actual values. Achieving an RMSE of 0.0244 and an R2 of 0.9975, these outcomes can offer precise quantitative information and advance energy-efficient materials. [ABSTRACT FROM AUTHOR]

Purpose: In everyday life, people generally wear two layers of clothes (a knitted vest and a knitted t-shirt) during the summer. It is essential to understand which types of innerwear and outerwear maximize comfort. The primary objective of this research is to investigate the influence of layering outerwear on innerwear, as well as the air gap between two layers, on thermal comfort properties. Design/methodology/approach: In this study, a total of 12 combinations were created from four vest fabrics and three T-shirt fabrics. The thermal properties (thermal conductivity, thermal resistance, thermal absorptivity, thermal diffusion and peak heat flow) were evaluated for the individual inner and outer layers. Each inner layer was layered with an outer layer to observe the effect of layering on the thermal properties. An air gap of 2 mm was introduced between the inner and outer layers to study the effect of air gap on thermal properties. Findings: Tencel fibre exhibits higher thermal conductivity and absorptivity than cotton and polyester. Upon layering an outer layer on an inner layer, the thermal conductivity and thermal absorptivity increase to a slight extent, thermal resistance and diffusion increase drastically and the peak heat flow reduces. With an air gap between the two layers, the thermal conductivity did not improve, the difference in thermal resistance among all the combinations reduced, the thermal absorptivity of the combination textiles was lower than that of the innerwear alone, the thermal diffusion increased and the peak heat flow diminished for all the combinations. Practical implications: In practice, this comprehensive thermal comfort analysis provides specific combinations of inner and outer articles of clothing that are most appropriate for enhancing comfort during the summer season. Originality/value: Though there are many studies on the effect of multilayer fabrics on thermal properties, no extensive research analyses the influence of innerwear and outerwear combinations on thermal comfort properties. [ABSTRACT FROM AUTHOR]

This paper presents an experimental and numerical study of the freezing-thawing behavior of water in fully saturated sand. A relatively inexpensive and easily replicable experimental procedure was developed to simulate the freezing-thawing cycles in a medium-sized sand sample placed in a modified commercial freezer. By insulating the sides and bottom of the sample well, while allowing good thermal conductivity at the top of the sample, a nearly vertical advance of the freezing and thawing front was achieved. A series of freeze-thaw cycles were performed with higher and lower temperature gradients. A numerical multiphysics model, assuming an axially symmetric geometry based on the transient heat transfer during the phase transition, used a parametric approach to estimate the effective thermal properties of the sand-water-ice system. A good agreement between experimental and modelling results was shown, but slightly different parameter sets were obtained for each temperature gradient. The presented method could be a simple way to characterize the freeze-thaw process in natural and artificial porous materials. [ABSTRACT FROM AUTHOR]

Lattice vibrations or phonons play an important role in determining material properties, including thermal conductivity. To model the phenomenon accurately and efficiently, the most important factors governing phonon physics need to be identified, for example, polarization branches. Research continues into many aspects of the fundamental physical processes involved in phonons and into possible applications of these processes in modern physics. One of the most interesting controversies in the thermal properties of graphene involves the importance of out-of-plane acoustic phonons. The need for clarity in understanding this importance dictates that the thermal conductivity of graphene should be evaluated in various circumstances. The nanoscale heat conduction properties of graphene are studied by iteratively solving the Boltzmann transport equation and rigorously treating the normal and Umklapp collisions in the frame of three-phonon interactions. This captures the mechanistic aspects of thermal conductivity by revealing what phonon branches are present. The thermal conductivity is evaluated in different crystallite sizes and at different frequencies and temperatures. The results indicated that out-of-plane acoustic phonons become increasingly important in the frame of three-phonon interactions. The out-of-plane acoustic branch dominates thermal transport whereas the other acoustic branches make small contributions. The importance of this branch is generally attributed to the high density of states and restrictions governing anharmonic effects. The three-phonon normal and Umklapp processes must be clearly accounted for and the contribution from optical branches is not negligible at higher temperatures. The results have implications in the quest for predictive and quantitative calculations of thermal conductivity. [ABSTRACT FROM AUTHOR]

Silicene has recently been revisited as a 2D material with potential thermoelectric applications. Here, the thermal properties of supported silicene are determined by optothermal Raman spectroscopy. Single and multilayer silicene is grown either directly on silver (Ag) substrates or on an intermediate tin (Sn) monolayer, introduced to reduce the influence of the substrate on the physical properties of silicene. Experimental values of an effective cross‐plane thermal conductivity of 0.5 W/mK are obtained for silicene on Ag and 0.3 W/mK for silicene on stanene‐Ag. The values of the interfacial thermal conductance, on the other hand, are 0.3 and 0.5 GW/m2K, respectively. Heterostack engineering is confirmed as a versatile strategy for extracting relevant physical parameters in silicene and for modulating the thermal response in the 2D limit. [ABSTRACT FROM AUTHOR]

The continuous upgrading of electronic technology has facilitated the integration and miniaturization of electronic and electrical equipment, as well as putting great pressure on the multifunctional demand for internal materials. Developing insulating materials with both low permittivity and high thermal conductivity has become imperative. This perspective focuses on polyimide (PI), which is the top material of the polymer material pyramid, discusses the characteristic parameters that affect its dielectric property and thermal conductivity. A series of basic schemes to regulate the dielectric/thermal properties of PI are summarized, revealing the bottlenecks and drawbacks of the current research. Future development trends of PIs featured low permittivity-high thermal conductivity are anticipated, and novel ideas are proposed for the development of new generation of multifunctional PIs. [ABSTRACT FROM AUTHOR]

Halide perovskites emerge as promising candidates for thermoelectrics due to their ultralow thermal conductivity. The conventional theory based on the phonon gas model, which treats thermal transport as particle‐like behavior, shows limitations to describe the unusual thermal transport property in some halide perovskites with strong anharmonicity. Here, the significance of phonon coherence effect on thermal transport of bismuth‐halide perovskite Cs3Bi2Br9 is reported by inelastic neutron scattering and simulations including density functional theory and machine‐learning potential based molecular dynamics. This study shows that the restrictive low‐energy acoustic phonons lead to the limited particle‐like thermal conductivity, which seriously underestimates the lattice thermal conductivity of Cs3Bi2Br9. The significant contribution of wave‐like optical phonon modes, driven by the coherence effect, accounts for an additional ≈50% wave‐like thermal conductivity. Besides, the experimental weak temperature dependence of thermal conductivity along z direction (κ ≈T−0.35) is well reproduced by calculation (κ ≈T−0.37) when including phonon coherence. This work highlights the critical role of phonon coherence in Cs3Bi2Br9 and enhances understanding on the unusual thermal transport properties in halide perovskites and other related materials with strong anharmonicity. [ABSTRACT FROM AUTHOR]

While improving the thermal conductivity of composites, single‐size carbon nanotubes (CNT) often degrade their mechanical properties due to the agglomerates. To overcome this limitation, this study reported thermoplastic resin matrix composites synergistically reinforced with small, medium, and large‐size carbon nanotubes (S‐CNT, M‐CNT, and L‐CNT). Using the thermal conductivity (λ) and mechanical properties (flexural strength [F], compressive strength [C] and tensile strength [T]) as the response values, we conducted 21 sets of mixing design experiments and developed the associated quadratic term models. Further multi‐objective optimization was carried out for the above response values. Optimized multiscale CNT synergistically modified composites (S‐CNT, M‐CNT, and L‐CNT contents of 1.25, 7.02, and 2.56 wt%) exhibited a λ value of 1.168 W/mK, which was 121% higher than that of pure composite and also superior to the same content of S‐CNT‐ (1.031 W/mK), M‐CNT‐ (1.016 W/mK), and L‐CNT‐modified composites (0.983 W/mK). Additionally, the optimized composite demonstrated excellent mechanical properties (F = 1482 MPa, C = 848 MPa, and T = 1759 MPa), which were 13%, 11%, and 13% higher than those of the pure composites, respectively, and also surpassed those of the S‐CNT‐, M‐CNT‐and L‐CNT‐modified composites. Highlights: Using three different scales of carbon nanotubes modified CF/PPBESK composites.Polynomial modeling of composite's thermal conductivity and mechanical properties.Synergistic interactions between carbon nanotubes to improve the composite's thermal conductivity and mechanical properties. [ABSTRACT FROM AUTHOR]

The relationship between interfacial structure and thermal conductivity in epoxy resin/Al2O3 composite is important but is still elusive. Here, we illuminate this issue by investigating the role of four silane coupling agents in thermal conductivity for epoxy resin/Al2O3 composites. The results show that 3‐glycidoxypropyltrimethoxysilane (KH560) is the best silane coupling agent to modify Al2O3, resulting in the lowest viscosity and the highest thermal conductivity of the epoxy resin/Al2O3‐KH560 composite compared with alternative systems. This is attributed to the strong interfacial interaction between Al2O3‐KH560 and epoxy resin, as confirmed by the Fowkes model and broadband dielectric spectroscopy. The interfacial thermal resistance between the epoxy resin and Al2O3 is also quantitatively measured via a photothermal radiometry technique. The epoxy resin/Al2O3‐KH560 also has the lowest interfacial thermal resistance (1.50 ± 0.02 × 10−6 m2 K W−1), compared with the other three systems. This study advances the understanding of the relationship between interfacial structure and thermal conductivity in polymer composites. Highlights: The relationship between interfacial structure and thermal conductivity in epoxy resin/Al2O3 composite is understood.The interfacial structure is characterized by broadband dielectric spectroscopy.The interfacial thermal resistance is quantitatively measured via a photothermal radiometry technique. [ABSTRACT FROM AUTHOR]

Thermal conductivity of moulding sands is very poorly known. In addition, the study of thermal conductivity variation of moulding sand as a function of its properties is a crucial step in the prediction of moulding defects. So, this study investigates the effects of moisture content, compactibility and permeability of green sand on its thermal conductivity variation, with a specific focus on the combination of bentonite, sand and water for thermal characterization of the transient hot-bridge (THB) method. Three levels of active clay content were selected: 8.1%, 8.98% and 10.03%. For each level of active clay, different mixes were made by varying the amount of added water. Compactibility, permeability and thermal conductivity tests were carried out for each combination of active clay and moisture contents. The experimental results show that thermal conductivity increases with water content and compactibility for different active clay contents, whereas thermal conductivity decreases with permeability, and this variation is highly significant especially for 8.07% of active clay content. [ABSTRACT FROM AUTHOR]

In this paper, a novel composite phase change material (CPCM) is prepared with inorganic PCM through impregnation and dispersion method which can be used for thermal management applications. Inorganic PCMs have high latent heat and good thermal conductivity and are non-flammable, but there exist leakage (shape stability) and corrosion problems. To overcome these issues, a porous structured material is impregnated with the inorganic PCM (disodium hydrogen orthophosphate dodecahydrate). The CPCM is prepared by loading various wt% of expanded graphite and boron nitride nanoparticles with the PCM, and characterization is performed to find the thermal properties and stability. The findings from FTIR and XRD analyses validate both the chemical compatibility and crystalline nature of the samples. DSC thermographs reveal the CPCM5 sample has a latent heat value of 168.05 J/g during the heating process, an encapsulation efficiency of 78.8% and a thermal conductivity of 4.69 W/mK. The thermal stability and resistance to corrosion of the composite samples are also enhanced. The best composite PCM sample is then selected, and subsequently, the thermal performance of the heat sink is experimentally investigated. The thermal performance of rectangular cavity heat sink filled with CPCM5 is the highest for various power sources and temperatures with a maximum enhancement ratio of 6.57. [ABSTRACT FROM AUTHOR]

The thermal barrier coatings (TBCs) system, a pivotal technology for advanced aviation engines and ground gas turbines, mitigates direct interaction between high-temperature gas and high-temperature alloy substrates. In this investigation, a series of high-entropy Eu 2 B 2 O 7 (where B = Y, Yb, Ce, Zr, Hf, Ta, and Nb) oxides were synthesized through solid-state reactions. By manipulating B-site cations and introducing substantial atomic size disparities, as well as mass and charge disorder, we synthesized a highly disordered high-entropy Eu 2 B 2 O 7 oxide. This oxide exhibits a disordered fluorite structure and commendable thermal insulation attributes. The observed thermal conductivity of Eu 2 (Y 0.2 Yb 0.2 Zr 0.2 Nb 0.2 Ta 0.2) 2 O 7 ranges from 0.94 to 1.13 W·m–1·K–1, which can be ascribed to amplified lattice anharmonicity and disorder causing supplementary phonon scattering. In addition, It also shows the thermal expansion coefficient of 10.52 × 10−6 K−1 and high-temperature stability. These results denote that the high-entropy Eu 2 B 2 O 7 oxide may become a prospective contender for thermal barrier coatings and thermal insulators. [ABSTRACT FROM AUTHOR]

The effects of Ta doping on the thermal and electrical properties of SnO 2 varistors were researched. The results showed that the thermal conductivity is 2.01 WK−1m−1, the nonlinearity coefficient is 43, and the leakage current density is 0.7 μA/cm2 when the Ta doping level reaches 0.2 mol%. According to the measurement results of the EPR, SEM/EDS, and XRD, the Ta dopant can reduce the oxygen vacancy concentration, which was generated during the sintering. The decline of the oxygen vacancy concentration reduces the phonon scattering, then the thermal conductivity of the varistors is improved. On the other hand, the reduction of the oxygen vacancy concentration elevates the barrier height, so the nonlinearity coefficient is improved and the leakage current density is declined. [ABSTRACT FROM AUTHOR]

In present work, high entropy (MoTaTiVW)C X ceramics with different carbon stoichiometries (X = 3–6) were produced using spark plasma sintering. The microstructure, mechanical properties, and thermal properties of (MoTaTiVW)C X with different carbon stoichiometries were studied. At X = 3, the carbon deficiency resulted in a multiphase structure of the sample, (MoTaTiVW)C 3 with a Mo-rich carbide phase. At X = 3.5, the single-phase rock salt structure was formed despite carbon vacancies of up to 30 %. The relative density of (MoTaTiVW)C X gradually decreases as the carbon stoichiometry increases from X = 3 to X = 6. The concentration of carbon vacancies affects the sintering activation energy, which can enhance mass transfer and promote the densification process. The Vickers hardness of (MoTaTiVW)C X shows an overall decreasing trend as the carbon stoichiometry increases from X = 3.5 to X = 6, peaking at 20.4 ± 0.4 GPa at X = 3.5. The fracture toughness increases and then decreases, peaking at 4.4 ± 0.2 MPa m1/2 at X = 4. The thermal conductivity of (MoTaTiVW)C X gradually increases, then decreases and finally increases with the increase of carbon stoichiometry. At room temperature, the maximum value of thermal conductivity is 6.35 ± 0.29 W/m·K of (MoTaTiVW)C 5 and the minimum value is 5.32 ± 0.35 W/m·K of (MoTaTiVW)C 5.5. At 1000 °C, the thermal conductivity of (MoTaTiVW)C X ranges from 15.94 ± 0.37 W/m·K to 19.56 ± 0.45 W/m·K. As the concentration of carbon vacancies decreases, the decrease in point defect concentration will reduce the degree of lattice distortion, thereby reducing phonon scattering and affecting thermal conductivity. The study suggests that carbon stoichiometry can be used to adjust the microstructure, mechanical properties, and thermal properties of high entropy carbide ceramics. [ABSTRACT FROM AUTHOR]

Highlights Acrylonitrile butadiene styrene (ABS) polymer has received considerable attention due to its high versatility for applications, including additive manufacturing. However, its electrical and thermal transport properties limit its application potential. One route to enhance electrical and thermal conductivities is the development of ABS‐based composites by using carbonaceous fillers, which have exceptional mechanical properties and remarkable functional properties. Here, we testing the presence of carbonaceous fillers with different dimensionalities on the electrical and thermal conductivity of ABS composites. In particular, one dimensional (1D) carbon nanotubes (CNT), two dimensional (2D) reduced graphene oxide (rGO), and three dimensional (3D) carbon black (CB) have been used to develop ABS‐based composites with different filler contents. A similar trend exist for the electrical and thermal conductivity results, where the highest conductivity values (electrical conductivity 0.0305 S·cm−1 and thermal conductivity 0.56 W·mK−1) being achieved for ABS‐based composites with 2D rGO filler, highlighting the relevance of specific characteristics of the 2D type filler. In addition, electromagnetic interference (EMI) shielding effectiveness (SE) of the ABS‐based composites containing rGO was superior to other 1D and 3D fillers. The stated correlation between electrical and thermal properties and their dependence on carbonaceous filler dimensionality are essential to be taken into account for properly tailoring functional properties of ABS‐based composites. Carbonaceous fillers are used to tailor several properties of ABS composites Significant differences are established between filler type or content Electrical percolation threshold strongly depends on the dimensionally 2D rGO more effective to improve electrical/thermal conductivities 1D CNT and 2D rGO fillers exhibit best EMI shielding properties [ABSTRACT FROM AUTHOR]

First-principles computations are used to investigate the structural, stability, mechanical, optical, thermal, and electronic characteristics of perovskite material. A novel RbBa 2 Ti 3 O 10 perovskite material is studied by using the generalized gradient approximation (GGA) suggested by Perdew, Burke, and Ernzerhof (PBE) approach in the CASTEP code. According to findings, the compound structure is tetragonal in nature with a space group of 123 (p4/mmm), a lattice parameter, and a volume. RbBa 2 Ti 3 O 10 exhibits indirect bandgap semiconductor behavior, according to its electronic characteristics. The Kramer-Kroning (KK) relations are used for determining optical properties to observe light-matter interaction. Perovskites' mechanical attributes, including their ductility, compressibility, elastic anisotropy, modulus, and mechanical index, were assessed and assigned. The thermal properties of the compound are examined, including its density, minimum thermal conductivity, melting temperature, and Debye temperature. Our investigation shows that RbBa 2 Ti 3 O 10 has potential use in photocatalytic applications. • The compound structure is tetragonal with a space group of 123 (p4/mmm). • RbBa 2 Ti 3 O 10 exhibits indirect bandgap (1.66 eV) semiconductor behavior. • Perovskites' mechanical attributes, like compressibility, anisotropy, modulus, and mechanical index, were assessed. • The thermal properties are examined, including its minimum thermal conductivity, melting temperature, and Debye temperature. • RbBa 2 Ti 3 O 10 has potential use in photocatalytic applications to separate water for H 2 and O 2 production. [ABSTRACT FROM AUTHOR]

Highlights A fluorinated polyimide (PI‐FTD) was synthesized for preparing a thermally conductive PI matrix and composites. Additionally, surface‐treated boron nitride (BN) was incorporated into the PI‐FTD via the solution casting method to form efficient heat paths along the through‐plane direction. The resultant composite demonstrated remarkable characteristics, including an impressive through‐plane thermal conductivity of 3.6 W mK−1, a substantial tensile strength of 69.4 MPa, and excellent thermal stability. When this composite was applied to light‐emitting diodes, it effectively managed heat, reducing the operating temperature by 29°C. The PI‐FTD/BN‐OH composites can potentially improve thermal management in electronic devices. A novel fluorinated polyimide (PI‐FTD) was fabricated. Introducing CF3 functionalities in the PI‐FTD provides high thermal stability. BN‐OH reinforced the thermal and mechanical properties of the composites. The PI‐FTD/BN‐OH composites achieved excellent thermal management. [ABSTRACT FROM AUTHOR]

Optimizing carrier concentration in PbTe materials can be achieved effectively through the chemical doping of sodium. Nevertheless, the valence balance can lead to the presence of "deleterious defects" in the PbTe matrix, resulting in low sodium solubility at room temperature. Herein, a strategy for fine‐tuning Pb vacancies to improve sodium solubility is developed. By a trace amount of Se‐doping, the solubility of Na in Pb0.99Te1‐xSex through the preservation of Pb vacancies in the matrix is substantially increased. Additionally, a large number of dense dislocations in the grains, which greatly reduced the lattice thermal conductivity is induced. A high power factor of ≈26 mW cm−1 K−2 and low lattice thermal conductivity of ≈0.43 W m−1 K−1 at 823 K in Pb0.95Na0.04Te0.97Se0.03 is achieved. Ultimately, a high figure of merit, ZT ≈2.2, is obtained at 823 K in quaternary PbTe compound. The current findings not only demonstrate that the introduction of trace amounts of Se and Pb vacancies in the PbTe matrix can effectively enhance Na solubility and minimize thermal conductivity, attaining synergistic improvement in electrical and thermal properties, but also indicate that the synergistic effect of Pb vacancies with a specific dopant is an alternative approach for enhancing ZT. [ABSTRACT FROM AUTHOR]

The strength of zirconium diboride ceramics was tested by three different methods, 3‐point flexure, 4‐point flexure, and compression. Nearly full‐density ceramics were obtained by hot pressing commercial ZrB2 powder with the addition of .5 wt.% carbon as a sintering aid. The thermal properties and hardness were studied for ZrB2 milled with ZrB2 and WC media. Based on phase purity and higher thermal conductivity, ZrB2 ceramics prepared from powders milled with ZrB2 media were selected for mechanical property studies. The strength in 3‐point flexure was 546 ± 55 MPa. The flexure strength was 476 ± 41 MPa in 4‐point bending, which was ∼20% higher than the previously reported value of 398 MPa for ZrB2 with similar grain sizes due to higher relative density and lower impurity contents. Compression testing was performed at room temperature, and the strength was 1110 ± 358 MPa. Finally, the fracture toughness of pure ZrB2 ceramics was determined by the chevron‐notched beam method to be 3.6 ± .7 MPa m1/2. The strength and fracture toughness values are higher than those previously published for ZrB2 ceramics and can be attributed to higher density and lower grain size. The strength‐limiting flaw sizes were comparable to the grain size, suggesting that porosity and impurity phases did not play a significant role in the strength of these ceramics. [ABSTRACT FROM AUTHOR]

The advancement of implantable biomedical devices (IMDs) hinges on the development of biocompatible solid-state electrolytes with outstanding electrochemical performance, safety, and reliability for flexible solid-state supercapacitors. This study focuses on the development of gel polymer electrolytes (GPEs) using polyvinyl alcohol (PVA) and potassium chloride (KCl). The GPEs obtained were subjected to comprehensive characterization using a diverse range of techniques to evaluate their spectral features, morphological properties, thermal and mechanical performance, biocompatibility, ionic conductivity, and cyclic stability. What distinguishes our research is its comprehensive exploration of the profound impact of varying PVA molecular weights and PVA/KCl weight ratios on the ionic conductivity and thermal characteristics of these gels. Notably, we observed a decrease in ionic conductivity with increasing PVA molecular weight, whereas an increase in salt concentration under the same molecular weight led to higher ionic conductivity. In particular, the optimal gel electrolyte with a molecular weight (Mw) of 195,000 g/mol and a PVA/KCl weight ratio of 1/2 demonstrated a promising ionic conductivity of 3.48 ± 0.25 mS/cm. Even after 5000 cycles, it retained 88% of its initial specific capacitance. Our findings reveal that the GPEs exhibit remarkable mechanical robustness alongside unparalleled ionic conductivity, characterized by minimal interfacial resistance. Moreover, these gel electrolytes exhibit remarkable biocompatibility, evident in a cell viability test where 72.3% of cells remained unaffected after a 72-h exposure to PVA/KCl. These findings present a promising avenue towards the fabrication of stable and high-performance biocompatible gel polymer electrolytes which can be used in solid-state supercapacitors, thereby laying the foundation for their integration into flexible, safer, and wearable bio-electronics. [ABSTRACT FROM AUTHOR]

Silicon carbide (SiC), as a third‐generation semiconductor material, has attracted significant research attention. Various empirical potentials and machine learning potentials have been developed, but there are few comparative studies on phonon and thermal properties. Herein, the Tersoff and Vashishta empirical potentials, as well as the Bayesian force field constructed by the FLARE framework using principled Gaussian process uncertainties (FLARE BFF), for a comparative study, are selected. The phonon dispersion relation, phonon density of states, Grüneisen constants, and the average phonon‐weighted Grüneisen constants are calculated using different potentials, and it is found that the FLARE BFF potential has the highest accuracy with respect to the first‐principles calculations. Furthermore, the thermal conductivity using molecular dynamics simulation with different potentials is calculated. The calculation results using the FLARE BFF potential closely match the experimental reports at high temperature, but the longest computing time is required. This study can facilitate the understanding of thermal properties of SiC. [ABSTRACT FROM AUTHOR]

In the context of ecological sustainability, this study focuses on the effect of variables of pasture fibers on the thermal properties of slag bricks made from a green recyclable material. This experiment uses slag as the binder, sand as the aggregate, and pasture fiber as an additive. The experimental variables include the additive content ratio of the pasture fiber, the size of the pasture fiber, and the type of pasture fiber. Significance analysis of the experimental results of the thermal performance tests is carried out using Minitab 18.1.0 software, and the optimal ratios for the thermal performance of the composite samples are derived from the response optimizer and conformity analysis. The results of the experiment's test analysis using Minitab 18 software indicate that, with an increase in pasture fiber content, the thermal performance of the composite samples initially decreases before increasing. Additionally, the lower the thermal conductivity of the composite sample, the lower the apparent density and the higher the porosity. Incorporating pasture fibers into slag bricks, as revealed in this study, reduces the waste of pasture resources in pastoral areas and promotes the development of sustainable building materials with favorable thermal properties. [ABSTRACT FROM AUTHOR]

Rare earth silicates are promising environmental/thermal barrier coating (E/TBC) materials facing severe CMAS (CaO‐MgO‐Al2O3‐SiO2) corrosion. Previous studies mainly focused on the intrinsic properties of precorrosion coatings, but there were few studies on their CMAS corrosion products that play a crucial role in the performance of coatings in postservice stage. In this work, the mechanical and thermal properties of nine corrosion products between lutetium silicates and CMAS are studied using first‐principles calculations. Their differences of elastic stiffness are attributed to the different crystal structures and bonding strength. The T:O ratio is identified as a factor of the crystal structure for silicate products, and it has a good correlation with their elastic stiffness. Moreover, the divergences of thermal conductivity are dominated by three essential factors, that is, atomic vibration intensity, lattice vibrational anharmonicity, and complexity of crystal structure. Compared with rare earth silicates, six products, that is, the α‐CaSiO3, β‐CaSiO3, Ca2MgSi2O7, Ca2Al2SiO7, CaAl2Si2O8, and Ca2Lu8(SiO4)6O2, showing good damage tolerance and low thermal conductivities, are predicted to be advantageous to E/TBCs. These discoveries reveal the mechanical/thermal properties of corrosion products between lutetium silicates and CMAS and are expected to support the future researches on the performance of E/TBC in the postservice stage. [ABSTRACT FROM AUTHOR]