Search

The mechanical properties for paper sheets composited with glucose (Glc), methyl cellulose (MC), and carboxymethyl cellulose (CMC) were investigated. The paper composites were prepared by immersing paper sheets in aqueous solutions of these materials and drying at 100 °C for 30 min. The stress–strain curves for these paper composites were measured by a uniaxial tensile apparatus with a stretching speed of 2 mm/min. The breaking stress and strain for untreated paper were 24 MPa and 0.016, respectively. The paper composites demonstrated stress–strain curves similar to the untreated paper; however, the breaking point largely differed for these composites. The breaking strain and breaking stress for the Glc composite slightly decreased and those for the MC composite gradually increased with the concentration of materials composited. Significant increases in the mechanical properties were observed for the CMC composite. The breaking stress, breaking strain, and breaking energy for the 3 wt.% CMC composite were 2.0-, 3.9-, and 8.0-fold higher than those for untreated paper, respectively. SEM photographs indicated that the CMC penetrated into the inner part of the paper. These results strongly suggest that the mechanical improvement for CMC composites can be understood as an enhancement of the bond strength between the paper fibrils by CMC, which acts as a bonding agent. It was also revealed that the breaking strain, breaking stress, and breaking energy for the CMC composites were at maximum at the first cycle and decreased gradually as the immersion cycles increased. [ABSTRACT FROM AUTHOR]

The demand for high-grammage paper, 150 g/m2 or more, is increasing for product protection and aesthetic value. Fold cracking, resulting from high mechanical pressure during folding, considerably decreases the economic feasibility of such products for papermaking companies. Fold cracking can be reduced through creasing, but defects possibly occur as fiber bonds are broken. In this study, the fold cracking of high-grammage paper that was not treated through creasing was explored. The mechanical and folding properties of six types of pulp fibers were evaluated based on their beating degree. The fines content of the fiber differed according to the beating condition. Using pulp with low fines content improved the folding properties. The mechanical properties of hardwood pulp were enhanced with increased beating degree. The mechanical properties of softwood pulp were considerably increased, and fold cracking occurred with increasing beating degree. Therefore, to improve the fold cracking, beating should be applied appropriately, following the type and mixing ratio of pulp fibers. Finally, softwood pulp mixing is proposed as a strategy to control fold cracking while maintaining the unique characteristics of high-grammage paper. [ABSTRACT FROM AUTHOR]

Hemp hurd fiber, a low-value waste stream from the hemp industry, has potential downstream applications as an alternative to non-renewable plastics for single-use food service ware and packaging applications. Packaging paper substrates made from chemically pulped hemp hurd, mixed in varying ratios with bleached thermomechanical radiata pine pulp were developed and tested. Handsheets were characterized using several mechanical property tests including tensile strength, tearing resistance, burst strength, short-span compression, ring crush, together with Gurley air resistance, contact angle, and Cobb60 tests. Generally, addition of hemp hurd fibers significantly improved handsheet mechanical properties. Hot-pressing of the handsheets so as to approximate molded fiber thermoforming further enhanced their performance, with pure hemp hurd handsheets having the highest mechanical properties and barrier performance. A prototype was successfully thermoformed from hemp fiber, demonstrating overall feasibility of this fibre source for molded fibre objects. [ABSTRACT FROM AUTHOR]

This review focuses on polymeric waste-paper composites, including state-of-the-art analysis with quantitative and qualitative discussions. Waste paper is a valuable cellulose-rich material, produced mainly from office paper, newspaper, and paper sludge, which can be recycled and returned to paper production or used in a new life cycle. A systematic literature review found 75 publications on this material over the last 27 years, with half of those published during the last five years. These data represent an increasing trend in the number of publications and citations that have shown an interest in this field. Most of them investigated the physicomechanical properties of composites using different contents of raw waste paper or the treated, modified, and cellulose-extracted types. The results show that polyethylene and polypropylene are the most used matrices, but polylactic acid, a biodegradable/sourced polymer, has the most citations. The scientific relevance of waste-paper composites as a subject includes the increasing trend of the number of publications and citations over the years, as well as the gaps identified by keyword mapping and the qualitative discussion of the papers. Therefore, biopolymers and biobased polymers could be investigated more, as well as novel applications. The environmental impact in terms of stability and degradation should also receive more attention regarding sustainability and life cycle analyses. [ABSTRACT FROM AUTHOR]

Thermal aging and ultraviolet (UV) irradiation are used as methods to prepare samples of kraft paper spanning its full lifecycle within a high-voltage transformer, from new to end of life. The mechanical break strain is correlated with the degree of polymerization (DP), representing a progressive deterioration of mechanical properties during aging. Subsequent exposure to oil flow mimicking both normal plant operation and reclamation activities shows that aged paper exposed to high rates of flow experiences noticeable surface roughening. Despite this, no measurable erosion occurs even after long-term temperature/flow cycling in used mineral oil containing a notable particulate content. This indicates that kraft paper is unlikely to be eroded by normal reclamation activities, even in a severely aged asset. This confirms the validity of using this approach to extend plant life. [ABSTRACT FROM AUTHOR]

Paper-based friction material is a typical paper-based composite that is usually cured via hot-pressing. This curing method does not account for the effect of pressure on the matrix resin, resulting in uneven distribution of resin in the material and reducing the mechanical properties of friction materials. To overcome the above shortcomings, a pre-curing method was introduced before hot-pressing, and the effects of different pre-curing degrees on the surface morphology and mechanical properties of paper-based friction materials were studied. The pre-curing degree significantly affected the resin distribution and interfacial bonding strength of the paper-based friction material. When the material was cured at 160 °C for 10 min, the pre-curing degree reached 60%. At this point, most of the resin was in a gel state, which could retain abundant pore structures on the material surface without causing mechanical damage to the fiber and resin matrix during hot-pressing. Ultimately, the paper-based friction material exhibited improved static mechanical properties, decreased permanent deformation, and reasonable dynamic mechanical properties. [ABSTRACT FROM AUTHOR]

The coefficient of friction for different contacting materials against skin is mainly influenced by the nature of the materials (synthetic and natural fabrics), mechanical contact parameters (interfacial pressure and sliding velocities), and physiological skin conditions (ambient humidity and skin moisture content). In the present research work, seven different types of papers used in everyday life were analyzed. The physical properties of these materials were determined through tensile tests and friction tests. By comparing mechanical properties with coefficient of friction, it was possible to conclude that the coefficient of friction is strongly correlated with the mechanical properties. [ABSTRACT FROM AUTHOR]

This study measured the decrease in some mechanical properties of kraft paper used in packaging and bag production by examining the colour changes occurring in accordingly prepared standard samples subjected to UV influence. Thus, it is aimed to predict the mechanical properties of packages that have been exposed to sunlight over long periods of time with the colour change measurement, which is a non-destructive test, without the packaging deformation. Since there are mechanical differences between the cross-machine width and machine length of fabricated papers, these were measured separately. Measurements were made on papers exposed to UV for 0, 120, 240, 360, 480, 600, and 720 h. Tensile strength, strain at break, and tensile energy absorption (TEA) values were measured and also predicted for the kraft paper. For the prediction, the time and colour change values were used as independent variables, whereas the mechanical properties were taken as the dependent variables. The relationship between the time and colour change and the tensile strength, strain at break, and TEA variables in both the crossmachine and the machine directions were significant at the 5% level, and the R2 values were within acceptable limits. The results showed that the mechanical properties of the papers under UV effect decreased proportionally with the increase of the UV time. [ABSTRACT FROM AUTHOR]

Simultaneous effects of using cellulose nanocellulose and chemical pulp in paper money were studied with bottom combers cotton pulp. The bottom combers pulp and chemical pulp were prepared in a factory that produced durable paper, and their products were transferred to the laboratory. The nanocellulose was prepared by Nano Novin Polymer Co. and was consumed at 4 levels, i.e., 0%, 0.3%, 0.6%, and 0.9%. After commixing the pulp with the nanocellulose at the identified percentages, handsheets of 90 g∙m-2 papers were produced. The results showed that by increasing the amount of nanocellulose, up to 0.9%, the tensile strength index, burst strength index, tear strength index, and folding endurance increased 22.7%, 38.9%, 7.7%, and 348%, respectively, when compared with the control sample. Enhancement via nanocellulose up to 0.9% increased the surface smoothness up to 7.9% compared with the control sample, while the air resistance and Cobb decreased 69% and 7.9% in comparison with control sample, respectively. By increasing the nanocellulose content up to 0.9% the opacity increased 0.7%; moreover, the brightness and whitening decreased 3.5% and 10.6, respectively. The scanning electron microscopy results indicated that enhancement via nanocellulose decreased the air resistance. [ABSTRACT FROM AUTHOR]

High-performance aramid papers are ideal insulating materials in the electric industry, due to their superior mechanical strength and insulation capabilities. However, when subjected to prolonged high-voltage and high-power operations, these papers are prone to electrical damage, such as breakdown or corona aging. Unfortunately, most damaged aramid papers are viewed as mere waste, discarded through landfill or other unsustainable disposal methods. It is not only contrary to circular economy principles but also poses a significant environmental threat due to the potential for pollution. Herein, a closed-loop recycling strategy is proposed that efficiently and effectively reclaims electrically damaged meta-aramid papers. Using the DMAc/LiCl deprotonation system, waste aramid papers are completely decomposed into molecular chains, exposing carbon residues resulting from electrical breakdown. These carbon residues are removed through a step-by-step purification process. A reprotonation treatment is then applied to regenerate new meta-aramid papers by reforming the intermolecular hydrogen bonds. This approach not only fully restores the original honeycomb-like structure but also ensures the crystallization and hydrogen bond content, maintaining both electrical and mechanical properties at above 90 % of their original values. Notably, our recycling method is also compatible with aramid-based composites, achieving exceptional recycling efficiency. [Display omitted] • Electrically damaged meta-aramid paper can be recycled in a closed loop. • The DMAc/LiCl system completely dissolves waste aramid into PMIA molecular chains. • Carbon residues induced by electrical breakdown can be removed by purification. • The synergistic conservation of electrical and mechanical properties exceeds 90 %. • Closed loop recycling strategy is also viable for inorganic-aramid composite paper. [ABSTRACT FROM AUTHOR]

The demand for particleboard has been increasing over the years. Currently, most particleboards are produced from wood which may not be sustainable in the long term. Therefore, there is need of exploring alternative materials such as making particleboards from waste materials. This study investigated the mechanical properties of particleboard consisting of waste leather shavings and waste papers blended together by unsaturated polyester. A single-layered particleboards were manufactured using compression method. Different resin contents (60%, 70%, 80%, and 90%) and leather/paper ratios (100:0, 25:75, 50:50, 75:25) were used to determine the effects on the mechanical properties (internal bond, bending strength, compression, and impact strength) of fabricated boards. From the results of this study, it was found that leather shavings and waste papers can be used as alternative raw materials for particleboard production and that mechanical properties were depended on the resin content and the blend ratio. Also, mechanical properties were reduced with resin content increment, except for impact strength, and improved by high paper blend ratio. It could be concluded that the produced particle panels could be used for indoor application or interior equipping. Additionally, it is recommended that further studies can be done on morphological analysis to establish the bonding between the particles and matrix. [ABSTRACT FROM AUTHOR]

The overall usefulness of the bursting energy absorption (BEA) was studied for a better analysis of paper strength properties. Additionally, the changes of the BEA during more complex deformations of paper products, e.g., preliminary or simultaneous tensile and burst, were determined. For the purpose of the research, an experimental setup was designed. The results showed that the correlation between BEA and bursting strength was linear, but the proportionality strongly depended on paper grade. Thus, a more accurate method to characterize the bursting resistance (BR) of paper was proposed. The BR parameter is described by the three following parameters: average bursting strength, average bursting energy absorption, and the slope of the fitted linear regression curve (relationship between the bursting energy absorption and the bursting strength). This method revealed new mechanical behaviors of papers related to their preloading. [ABSTRACT FROM AUTHOR]

In this study, high-pressure laminates (HPL) impregnated with phenol-formaldehyde (PF) resins enriched with kraft lignin were developed. Pulverised kraft lignin was added to the commercial PF resin in the amounts of 1% and 5% (solid to solid). Laminates were manufactured using pressure impregnation of the resins into the papers and using hot pressing of HPL in a laboratory press. Laminates with a lignin content of 1% (L-LPF-1) showed the highest bending strength (72.42 MPa) and Brinell hardness (9.41); they also exhibited the best moisture uptake (9.61) and thickness swelling after immersion in water (3.32%). Except for impact bending, laminates with a lignin content of 5% (L-LPF-5) had worse properties. However, the differences between the variants are mostly not statistically significant and are comparable with the results of commercial PF resin. Scanning electron microscopy confirmed the homogenous structure of produced laminates and the occurrence of cohesive failures in ruptured L-LPF-1 laminates, whereas in ruptured L-LPF-5 laminates adhesive failures were also observed. Based on the conducted research it can be said that the utilisation of kraft lignin as an additive to PF resin (in the amount of 1%) has a positive effect on the produced HPL. [ABSTRACT FROM AUTHOR]

The effects of nanoclay were studied relative to the physical, mechanical, optical, and morphological properties of chemimechanical pulping papers. Nanoclay was incorporated at 0%, 2%, 4%, 6%, 8%, or 10%. To increase the retention, 1% cationic starch was used in all test papers. Handsheets (60 g/m2 in weight) were tested to determine their physical, mechanical, optical, and morphological properties. Up to 2% nanoclay increased the tensile strength; at values greater than 2%, the tensile strength decreased. The addition of up to 4% nanoclay increased roughness; between 4% and 10% nanoclay, roughness decreased. With 10% nanoclay, the tear strength, burst strength, and brightness decreased, but the air resistance, opacity, and yellowness increased. Scanning electron microscopy showed that the nanoclay filled the pore spaces between fibers, thus increasing air resistance. X-ray diffraction patterns indicated an intercalated structure. [ABSTRACT FROM AUTHOR]

The potential utilization of melamine impregnated paper (MIP) waste in thermoplastic composites was investigated. Composites were also manufactured utilizing wood flour (WF) at the same filler rates for comparison. The composites were manufactured using a compression molding method. The effects of filler type and filler rate on the mechanical properties of low-density polyethylene (LDPE)-based composites were evaluated. Mechanical properties, such as tensile and flexural strengths, were determined in accordance with ASTM D638 (2001) and ASTM D790 (2003), respectively. Results showed that filler type and filler content had significant effects on all mechanical properties investigated. Both fillers improved all mechanical properties except for tensile strength and elongation at break of LDPE. In conclusion, MIP waste has a potential to be utilized in thermoplastic-based composite manufacturing and might generate some economic and environmental benefits. [ABSTRACT FROM AUTHOR]

Embossing is a functional and strategic process for creating high-quality multi-sensory tissue-paper products. Embossing modifies the sheet surface by generating hill and/or valley designs, changing the third-dimension z with a compressive die. This research work specifically concerns the impact study of the engraving finishing geometry on the final properties of tissue paper. This work led us to conclude that, even though the sheets individually present a higher hand-feel (HF) value for the straight finishing geometry, the highest softness was obtained in the two-ply prototype for the round finishing geometry. Moreover, this study confirmed that the HF value reduces with the increase of the bulk, being more accentuated for the micropattern. Relevant differences could not be seen in the spreading kinetics of the liquid droplets over time. Thus, the finishing geometry of the 3D plates did not impact the absorption kinetics on these samples. The finite element model allows us to understand the effect of the plate pattern and its finishing geometry on the paper, and the simulation results were in accordance with the experimental results, showing the same trend where patterns with a round finishing geometry marked the tissue-paper sheet more than patterns with a straight finishing did. [ABSTRACT FROM AUTHOR]

This review presents the research conducted to date in the field of cement-based composites reinforced with waste paper-based cellulose fibres, focusing on their composition, mechanical properties, and durability characteristics. The literature demonstrates that the properties of raw material (depending on their own chemical composition) significantly influence the formation of the cement composite binders. When considering fresh properties, the presence of silica and magnesium compounds generally lead to favourable effects on the setting of the cement composite when combined with waste paper cellulose fibre. Reduction in density values, i.e., approximately 25%, was observed with the inclusion of waste paper fibres from 20 to 80% in cement composites. The homogeneous dispersion of fibres in the matrix is one of the crucial factors to achieve in order to develop composites with well-balanced mechanical properties incorporating waste paper cellulose fibres. Hence, dispersion of fibres can be improved by increasing water quantity corresponding to the optimal value, which was a water/cement ratio of 0.64 leading to optimum strength properties of the composite. Even though the effect of fibre dispersion in the matrix improves with the addition of water, higher porosity and voids govern the strength properties beyond an optimum water-to-cement ratio. Higher porosity leads to an increase in the water absorption and a lowering of the thermal conductivity properties with the addition of paper fibre in cement binders. Paper fibre absorbs a high amount of water leading to higher water absorption. This phenomenon is related to the hydrophilic nature of cellulosic fibres absorbing some volume of water due to their microporous structure. [ABSTRACT FROM AUTHOR]

The embossing operation is one of the processes of tissue paper converting. The embossing parameters influence the final properties of tissue products, such as mechanical, softness, and bulk. In this study, the influence of the rubber hardness used against the embossing steel rolls with a pattern created by intaglio engraving was studied. Three different configurations of rubber plates stacking, each plate with different hardness, were studied. After embossing, mechanical properties, softness, and bulk were evaluated to analyze the effect of rubbers hardness on these properties. Furthermore, a Finite Element Model of the embossing operation was used that considered the same rubber plates stacking configurations used in experiments, and it was able to replicate the experimental results. This work led us to conclude that the configuration where two rubber plates with different hardness, where the rubber plate with higher hardness is in contact with the tissue paper sheet, has shown to be the best solution to obtain higher softness. These findings support the use of embossing operations rubber rolls with a low hardness internal layer and a high hardness external layer in industry. Thus, finite element models were also shown to be reliable tools to virtually test other configurations, such as, for example, three or more rubber plates with different hardness. Since embossing is one of the tissue paper transformation operations with the greatest impact on the key properties of the final product, this study allows the producer to optimize them by varying the hardness of the rubber roll, as well as its configuration. [ABSTRACT FROM AUTHOR]

Embossing is a converting process in which the surface of a tissue paper sheet is changed under high pressure, allowing different functions. In this work, the authors intend to study how the embossing pressure affects the main properties of tissue paper, using a laboratory embossing system. An optimum pressure was achieved at 2.8 bar to this embossing laboratory set-up. The effect of pressure when densifying the paper sheet gives it a gain in mechanical strength but no differences in terms of liquid absorbency. The two embossing patterns present different behaviors but both evidence losses in mechanical and softness properties. On the other hand, the finite element method (FEM) does not show clear evidence of how the pressure affects the paper strength. For the deco die, it is possible to observe that the amount of yielding is slightly higher for lower pressure (2.4 bar), but this plasticity state parameter is very similar for 2.8 bar and 3.2 bar. For the micro die, FEM simulations of the manufacturing pressure do not show a considerable impact on the amount of plasticity state of the material; only for 3.2 bar, it shows a change in the pattern of the plasticity state of the paper during the embossing processes. In the end, to achieve a final product with excellent quality, it is important to make a compromise between the various properties. [ABSTRACT FROM AUTHOR]

The paper tissue industry is a constantly evolving sector that supplies markets that require products with different specific properties. In order to meet the demand of functional properties, ensuring a green approach at the same time, research on bio-coatings has been very active in recent decades. The attention dedicated to research on functional properties has not been given to the study of the morphological and mechanical properties of the final products. This paper studied the effect of two representative bio-based coatings on paper tissue. Coatings based on chitin nanofibrils or polyphenols were sprayed on paper tissues to provide them, respectively, with antibacterial and antioxidant activity. The chemical structure of the obtained samples was preliminarily compared by ATR-FTIR before and after their application. Coatings were applied on paper tissues and, after drying, their homogeneity was investigated by ATR-FTIR on different surface areas. Antimicrobial and antioxidant properties were found for chitin nanofibrils- and polyphenols-treated paper tissues, respectively. The mechanical properties of treated and untreated paper tissues were studied, considering as a reference the same tissue paper sample treated only with water. Different mechanical tests were performed on tissues, including penetration, tensile, and tearing tests in two perpendicular directions, to consider the anisotropy of the produced tissues for industrial applications. The morphology of uncoated and coated paper tissues was analysed by field emission scanning electron microscopy. Results from mechanical properties evidenced a correlation between morphological and mechanical changes. The addition of polyphenols resulted in a reduction in mechanical resistance, while the addition of chitin enhanced this property. This study evidenced the different effects produced by two novel coatings on paper tissues for personal care in terms of properties and structure. [ABSTRACT FROM AUTHOR]

Polyhedral oligomeric silsesquioxane (POSS) has a total of eight substituents. The number of substituents determines the modification effect of POSS. Through simulation of molecular dynamics, this paper explores how the number of substituents affects the POSSmodified cellulose insulation paper. Specifically, the mechanical properties, thermal stability and polarizability were calculated for cellulose models with 1-phenyl POSS, 2-phenyl POSS, 3-phenyl POSS, 4-phenyl POSS, 5-phenyl POSS, 6-phenyl POSS, 7-phenyl POSS, and 8-phenyl POSS, respectively. The results show that the cellulose model modified by 6-phenyl POSS achieved better effect than the other seven models, as evidenced by its distinctively large bulk modulus, shear modulus, and elastic modulus. Besides, the cellulose model modified by 6-phenyl POSS had the most stable and the minimum mean square displacement (MSD). This is because the mechanical properties of the insulation paper are improved, as the motion of cellulose chains is inhibited by the nano-size effect of POSS and the effect of phenyls. Further, the cellulose model modified by 6-phenyl POSS also had the smallest polarizability among the modified models. Therefore, the 6-phenyl POSS-modified cellulose model can effectively reduce the polarizability of cellulose, uniform the electric field distribution in oil-paper insulation system, and thus enhance the insulation property of transformers. [ABSTRACT FROM AUTHOR]

Highlights • Mechanical properties of waste papers are closely correlated with devolatilization. • Start of devolatilization caused a sudden decrease in relative storage modulus ( E ′ r). • Kinetics of storage modulus change is investigated referring to activation energy. • E ′ r can be predicted with mass loss ratio and CO 2 emission. Abstract This article details a correlation study on early devolatilization behaviors (drying & volatile emission at 25–240 °C) and the change in mechanical properties (expressed by viscoelasticity) of four types of waste papers. The early stage of devolatilization was investigated using the TG-FTIR and mechanical properties using the dynamic mechanical analysis (DMA) method. The results show that the elastic and viscous mechanical properties showed obvious correlations with free and bound water evaporation and volatile emission. The storage modulus (E ′) and loss modulus (E ″) of the papers decreased as temperature increased and at the two important temperatures, namely 100 °C, the start of bound water evaporation, and 150 °C, the start of devolatilization in TG & DTG curves, E ′ showed extrema. Especially the relative storage modulus ( E ′ r) exhibited a sudden decrease at around 150 °C, where the activation energy of thermochemical conversion jumps from low values to high values, indicating the start of devolatilization. CO 2 is the major compound of the volatiles and it is well correlated with E ′ r in exponential function model and can be used as an index for predicting the E ′ r of the waste papers in their early devolatilization stage; while during the drying stage, mass loss ratio can be used to predict E ′ r of the waste papers. [ABSTRACT FROM AUTHOR]

Xylan is the primary hemicellulose in most hardwood species, especially in birch. Research has highlighted the exploitation of xylans as a strengthenhancing additive to paper due to the current trend for the effective utilization of biomass. In this paper, a new pulping process was proposed, which involved the extraction of xylan prior to pulping, followed by the readsorption of the pulp after the final stage in the digester, followed by a suitable bleaching process. The aim of this work was to bleach hardwood kraft pulp (brown pulp) with adsorbed birch xylan via hydrogen peroxide and study the effect of the bleaching parameters on the paper properties. The results showed that the optical properties of paper decreased; however, the mechanical properties increased after the brown pulp adsorbed birch xylan. During the bleaching process, better mechanical properties were obtained with shorter bleaching times and lower bleaching temperatures, initial pHs, and MgSO4 dosages. However, the optical properties were improved as the bleaching time, temperature, initial pH, and MgSO4 dosage were increased. The adsorption of birch xylan could effectively modify the mechanical properties of paper made from brown pulp under various phases. [ABSTRACT FROM AUTHOR]

Alkyl ketene dimer (AKD) and rosin sizing are used in papermaking to decrease paper's tendency to absorb liquid water. Earlier information regarding the effects of internal sizing on paper dry strength is not consistent. In the present laboratory study, AKD sizing of handsheets made from Nordic bleached softwood pulp (NBSK), and rosin sizing of handsheets made from Nordic hardwood chemi-thermomechanical pulp (CTMP) were done via an internal sizing method, and by immersing handsheets in aqueous sizing agent dispersion. In the study, AKD sizing had no significant effect on the dry strength of NBSK handsheets. The result corresponds to practical experiences of papermakers. However, both AKD sizing methods resulted in a substantial and long-lasting increase of handsheet wet-strength. Unlike internal AKD sizing of NBSK handsheets, rosin internal sizing of CTMP handsheets resulted in decreased handsheet dry strength. The decrease indicates that, under the conditions present during the experiment, rosin sizing agents interfered with interfiber hydrogen bonding of CTMP fibers. Given that, in practice, no such undesired effects have been commonly linked to rosin sizing, the observed effect may be specific to sheet-making conditions. However, the effect of rosin sizing on strength properties and their variation cannot be ruled out completely. [ABSTRACT FROM AUTHOR]

In this work, a robust and flexible bilayered MXene/cellulose paper sheet with superhigh electrical conductivity was prepared via vacuum-assisted filtration and a subsequent hot-pressing process for electromagnetic interference (EMI) shielding applications. By tightly assembling few-layered MXene (f-Ti 3 C 2 T x) on the cellulose substrate via hydrogen bonds, an effective and interconnected conductive network was constructed in the paper sheet, resulting in a high electrical conductivity of 774.6–5935.4 S m−1 at various f-Ti 3 C 2 T x loadings. The highly conductive MXene layer can promptly reflect a great amount of incident EM waves, a process which preceded the transmission of EM waves in the cellulose matrix. Owing to the highly efficient reflection-dominated EMI shielding mechanism, the resultant bilayered MXene/cellulose paper sheets exhibit excellent EMI shielding effectiveness of 34.9–60.1 dB and specific EMI shielding efficiency of 290.6–600.7 dB mm−1. Moreover, the MXene/cellulose paper sheets demonstrated improved mechanical strength (up to 25.7 MPa) and flexibility due to the mechanical frame effect acted by the cellulose substrate. Consequently, the robust and flexible bilayered MXene/cellulose paper sheet is a promising candidate for application in next-generation electric devices. [ABSTRACT FROM AUTHOR]

The paper describes the structure and properties of preceramic paper-derived Ti 3 Al(Si)C 2 -based composites fabricated by spark plasma sintering. The effect of sintering temperature and pressure on microstructure and mechanical properties of the composites was studied. The microstructure and phase composition were analyzed by scanning electron microscopy (SEM) and X-ray diffraction (XRD), respectively. It was found that at 1150 °C the sintering of materials with the MAX-phase content above 84 vol% leads to nearly dense composites. The partial decomposition of the Ti 3 Al(Si)C 2 phase becomes stronger with the temperature increase from 1150 to 1350 °C. In this case, composite materials with more than 20 vol% of TiC were obtained. The paper-derived Ti 3 Al(Si)C 2 -based composites with the flexural strength > 900 MPa and fracture toughness of >5 MPa m1/2 were sintered at 1150 °C. The high values of flexural strength were attributed to fine microstructure and strengthening effect by secondary TiC and Al 2 O 3 phases. The flexural strength and fracture toughness decrease with increase of the sintering temperature that is caused by phase composition and porosity of the composites. The hardness of composites increases from ~9.7 GPa (at 1150 °C) to ~11.2 GPa (at 1350 °C) due to higher content of TiC and Al 2 O 3 phases. [ABSTRACT FROM AUTHOR]

In this study, extractives from Pinus rigida heartwood (PRW), Eucalyptus camaldulensis var. obtusa aerial parts (ECL), and Eucalyptus flower buds (ECF) were used as additives in paper sheets produced from the pulp of linen fibers, and their effects on the mechanical and antifungal properties of the paper sheets were studied. The highest tensile and tear indices were 31.5 Nm/g, and 17.3 mNm2/g as pulp treated with PRW (4%), and ECL (1%), respectively. All the pulp additives yielded lower burst index values compared to the control (2.24 KPa.m2/g); the nearest value was 2.23 KPa.m2/g (ECL 4% pulp additive). The brightness percentages (ISO%) ranged from 65.7% to 70.2%, which were lower than the control treatment (70.3%). The paper sheets produced from pulp treated with 2% or 4% PRW, and with 4% ECL suppressed Aspergillus niger growth on the paper disc; pulp treated with 2% or 4% PRW, 4% ECL, and with 2% or 4% ECF completely suppressed A. terreus growth. However, all pulp extract additives did not inhibit the growth of Fusarium culmorum. [ABSTRACT FROM AUTHOR]

Various approaches have been exploited to copy nacreous structure into human‐made structural nanocomposites with similar structure and impressive mechanical performance. However, it is still facing a great challenge to produce large‐sized, strong, and tough, biopolymer‐based nanocomposite, especially for further scale‐up in practical application. Herein, a large‐sized and nacre‐inspired nanocomposite paper can be successfully prepared via a simple evaporation‐induced self‐assembly technique, based on assembling hybrid graphene oxide/sodium alginate (GO/SA) building blocks. Through optimizing the lamellar hybrid interfacial interactions derived from hydrogen‐bonding network, the nacre‐inspired nanocomposite achieves a unique integration of high strength (up to 350.3 MPa) and high toughness (22.4 ± 2.9 MJ m−3), are superior to natural nacre, almost all GO and SA‐related composites, and many engineering materials. The hydrogen bond‐property correlation, combined with a simple assembling technique, will provide a powerful path for the large‐scale production of lightweight, biopolymer‐based materials with excellent mechanical properties. [ABSTRACT FROM AUTHOR]

[Display omitted] • The simulation results successfully guided the preparation of the insulating paper. • Nano-SiO 2 enhances the interfacial binding and compatibility of composite fiber. • Nano-SiO 2 improved the mechanical and insulating properties of the insulating paper. • Nano-SiO 2 reduced the energy barrier of composite fiber and reduce polarization loss. Following the surge in power loads and continuous improvement in the voltage level, insulating papers' mechanical and electrical properties face new challenges. However, traditional inefficient "tentative" trial and error experiments are formidable to rapidly and efficiently prepare cellulose composite insulating paper because the direct scientific theory or simulation guidance is insufficient. To solve this problem, the nano-silica(nano-SiO 2)/polyimide(PI)/cellulose composite models were designed and their mechanical, and dielectric properties were predicted by molecular dynamics (MD) simulation. The preparation of corresponding nano-SiO 2 /PI/cellulose insulating paper was guided by the MD simulation results and their surface morphology, mechanical properties, and electrical properties were investigated. The experimental results are in good agreement with the MD simulation results and confirmed that P3 insulating paper possesses the best comprehensive performance, and its tensile strength, relative permittivity, dielectric loss, volume resistivity, and breakdown strength are 71.44 MPa, 2.39, 0.2%, 5.16 × 1015 Ω∙m, and 75.8 kV∙mm−1, respectively. This work proves the feasibility and effectiveness of using MD simulation to guide the development of new insulating papers, and compared with the existing traditional preparation methods, this method is expected to be applied to study various new materials in the future and promote the vigorous development of new materials. [ABSTRACT FROM AUTHOR]

Paper money passes through various environments during its life span, causing its physical, chemical, and optical properties to change. More than 90% of paper money worldwide is composed of natural cotton fiber. The present study examined the properties of paper money made of bleached softwood kraft fibers or its blends with cotton fibers, where nanofibrilled cellulose was employed as a strengthening agent. Nano-cellulose was added at 4 levels: 0, 0.3, 0.6, and 0.9%. Handsheets with a basis weight of 90 g·m-1 were made by mixing the pulp furnish with nano-cellulose in the identified percentages, and the physical and mechanical properties of the handsheets were tested. By increasing the amount of nano-cellulose up to 0.9% in cotton pulp, the tensile strength, bursting resistance, tear resistance, and resistance to folding endurance were increased by 33, 33.5, 6.6, and 63.2%, respectively, compared with the control sample. The addition of nano-cellulose up to 0.9% in cotton pulp increased the surface smoothness by up to 13.5% compared with the control sample, and porosity and water absorbance decreased by 16.6 and 4%, respectively, in comparison with the control sample. By increasing nano-cellulose up to 0.9% in cotton pulp, the opacity, brightness, and whiteness were decreased by 0.1, 1, and 4%, respectively. The SEM results indicated that the increased nano-cellulose percentage led to decreased porosity. [ABSTRACT FROM AUTHOR]

The effect of nanofibrillated cellulose (NFC) was investigated relative to the strength of chemi-mechanical pulp (CMP) and paper. The NFC was added at five levels: 0%, 2%, 4%, 6%, and 8%. Handsheets with a basis weight of 60 g/m² were prepared, and the physical properties (air resistance and surface roughness), the mechanical properties (tensile strength, burst strength, and tear strength), and the optical properties (brightness, opacity, and yellowness) were measured according to TAPPI standards. By increasing the NFC content, the tensile strength, burst strength, air resistance, brightness, and whiteness increased by 10.9%, 12.5%, 23.6%, 0.6%, 3.5%, and 6.8%, respectively, compared to the control (0% NFC) samples. By increasing the NFC content, the tear strength, roughness, and opacity decreased by 10.4%, 11.1%, and 0.6% compared to the control samples. [ABSTRACT FROM AUTHOR]

The mechanical performance of two commercial papers used as solid insulation in power transformers, namely standard Kraft and a thermally upgraded Kraft paper, were studied during accelerated aging in Luminol oil at 170 ?C. The results show a relationship between the degree of polymerization and the mechanical properties measured by tensile testing. A linear relationship was found between the mechanical properties of paper, the tensile index (Tidx), and the concentration of methanol present in the oil. The methanol chemical marker has been proven to be an accurate assessment tool for the aging of cellulosic paper. The results show a promising tool for correlating the methanol concentration in oil, as an indirect indicator, with the mechanical performance of the paper. This approach can be used to monitor the real state of the cellulose chains in the power transformer insulation paper. [ABSTRACT FROM AUTHOR]

Background: As a result of use of library and archival documents, defined as reading with handling in the context of general access, mechanical degradation (wear and tear) accumulates. In contrast to chemical degradation of paper, the accumulation of wear and tear is less well studied. Previous work explored the threshold of mechanical degradation at which a paper document is no longer considered to be fit for the purpose of use by a reader, while in this paper we explore the rate of accumulation of such damage in the context of object handling. Results: The degree of polymerisation (DP) of historic paper of European origin from mid-19th-mid-20th Century was shown to affect the rate of accumulation of wear and tear. While at DP > 800, this accumulation no longer depends on the number of handlings (the process is random), a wear-out function could be developed for documents with DP between 300 and 800. For objects with DP < 300, one large missing piece (i.e. such that contains text) developed on average with each instance of handling, which is why we propose this DP value as a threshold value for safe handling. Conclusions: The developed model of accumulation of large missing pieces per number of handlings of a document depending on DP, enables us to calculate the time required for an object to become unfit for use by readers in the context of general access. In the context of the average frequency of document use at The UK National Archives (Kew), this period is 60 years for the category of papers with DP 300, and 450 years for papers with DP 500. At higher DP values, this period of time increases beyond the long-term planning horizon of 500 years, leading to the conclusion that for such papers, accumulation of wear and tear is not a significant collection management concern. [ABSTRACT FROM AUTHOR]

This article describes a study on the viability of using waste from the paper industry: biomass boiler ash and green liquor dregs to fabricate mortars and concretes. Both types of ash were characterized by obtaining their chemical and mineralogical composition, their organic matter content, granulometry, adsorption and other common tests for construction materials. Seven different mortars were fabricated, one for reference made up of cement, sand, and water, three in which 10, 20, or 30% of the cement was replaced by biomass ash, and three others in which 10, 20, or 30% of the cement was replaced with dregs. Test specimens were fabricated with these mortars to conduct flexural and compression tests. Flexural strength is reduced for all the mortars studied. Compressive strength increases for the mortars fabricated with biomass ash and decreases for the mortar with dregs. Finally, 5 concretes were made, one of them as a reference (neither biomass ash nor dregs added), two of them with replacements of 10 and 20% of biomass ash instead of cement and another two with replacements of 10 and 20% of dregs instead of cement. The compressive and tensile splitting strength increase when a 10% of ash is replaced and decrease in all the other cases. The modulus of elasticity always decreases. [ABSTRACT FROM AUTHOR]

Abstract Al 2 O 3 /Cu-O composites were fabricated from the paper-derived alumina matrix infiltrated with a Cu-3.2 wt% O alloy. Paper-derived alumina preforms with an open porosity ranging from ∼ 14 to ∼ 25 vol% were prepared by sintering of alumina-loaded preceramic papers at 1600 °C for 4 h. Pressureless infiltration at 1320 °C for 4 h of the preforms with Cu–O alloy resulted in the nearly dense materials with good mechanical and electrical properties, e.g. fracture toughness up to 6 MPa m0.5, four-point-bending strength up to 342 MPa, Young's modulus up to 281 GPa and electrical conductivity up to 2 MS/m depending on the volume fraction of copper alloy in the composites. The technological capability of this approach was demonstrated using prototypes in various engineering fields fabricated by lamination, corrugating and Laminated Object Manufacturing (LOM) methods. [ABSTRACT FROM AUTHOR]

The article presents continued considerations presented in a prior publication on the development of a model for calculating the bending stiffness BS of cellular honeycomb paperboards, applying the strength properties of paper raw materials used for the production of paperboard and the geometric parameters of cellular board. The results of BS calculations obtained by using the analytical model presented in the prior publication were significantly overestimated in relation to the value obtained by measurements. The calculation error in relation to the measurement value for the tested group of paperboards in the case of bending stiffness in the machine direction MD was within the range from 23% to 116%, and the average error was 65%, while in the cross direction CD, it was within the range from 2% to 54%, and the average error was 31%. The calculation model proposed in this work based on the physical properties of cellular paperboard reduces the error values for bending stiffness in both the machine and cross directions. The value of the average error for both main directions in the paperboard plane was 10%. The method enables more accurate determination of BS in the machine direction MD and in the cross direction CD at the paperboard design stage. In order to validate the proposed analytical model, the calculation results were compared with the results of BS laboratory measurements performed using the four-point bending method and, in order to expand the group of tested paperboards, with the measurement results presented in the prior article for cardboards with different raw material composition and different geometric parameters. [ABSTRACT FROM AUTHOR]

Abstract We developed a paper-type electrode for the next-generation wearable devices by complementary hybridization of methyl cellulose and carbon nanotubes (CNTs). The large-scale hybrid paper was fabricated using an incomparably simple and low-cost solution process. Structural features, surface hydrophobicity, and chemical interaction between CNTs and cellulose of the hybrid papers were systematically explored by adjusting the concentration of CNTs. The hybrid papers demonstrated superb mechanical durability even under highly strained conditions such as folding, crumpling and re-flattening regardless of the concentration of CNTs. The electrical properties of the CNTs/methyl cellulose were well-preserved even when folded as origami or submerged in water. [ABSTRACT FROM AUTHOR]

The goal of this study was to analyze the effects of cellulose fibers loading by precipitation in-situ of calcium carbonate over the properties of printing paper obtained from mixtures of the softwood and hardwood fibers. The effects of fibers with in-situ loading were analyzed comparatively with conventional paper loading respectively, by adding precipitated calcium carbonate into fiber stock. The effectiveness of the methods was evaluated by various analyses and investigations: calcium carbonate content, Scanning electron microscope (SEM) images, X-ray diffraction, optical and mechanical properties of the paper sheets. The evaluation of the effects on paper properties led to the conclusion that, at the same filler content, the in-situ loading method gives higher opacity and brightness than conventional methods. The utilization of cellulose fibers with in-situ loading as additive, shown as a modification of the ratio between fibers with in-situ loading and fibers without loading, regardless of whether they are softwood or hardwood fibers, allowed us to optimize printing paper properties, especially regarding the relationship between optical and strength properties. [ABSTRACT FROM AUTHOR]

Many researchers are interested in using natural fibres to treat due to recent advancements in polymer characteristics. The mechanical properties of three types of bars are studied in this paper: Cotton Fibre-Reinforced Polymer bars, Cotton/Carbon Fibre-Reinforced Polymer bars, and Cotton/Glass Fibre-Reinforced Polymer bars. The goal of the paper was to create low-cost bars with comparable mechanical performance and corrosion resistance to steel reinforcement. The bars were made using two methods: fibres immersed in polymer and fibres coated with polymer by repeated tension and relaxation of fibres. The second method produced better results in terms of the tensile strength of Cot.CFRP, Cot.GFRP, and Cot.FRP bars, which were 688, 477, and 284 MPa, respectively, and the stress–strain curve revealed brittle behaviour for all bars and modulus of elasticity of 43, 31 and 22 GPa. When sand was put on the bar's surface, the bars demonstrated a good connection with the concrete. It also showed good resistance to moisture, alkaline solutions and acids, as well as heat resistance at temperatures below 200°C. [ABSTRACT FROM AUTHOR]

This paper presents a novel approach to enhance the energy absorption (EA) of honeycombs in the out-of-plane direction. Inspired by the Koch fractal, a fractal hexagonal honeycomb (FHH) is presented in this paper. In our study, we use Abaqus/Explicit to build a finite element model of the honeycomb, through which we conduct a series of studies on the performance of this honeycomb. Initially, we compare the mechanical properties and deformation modes of the FHH with those of a conventional hexagonal honeycomb. The results demonstrate notable improvements in crashworthiness metrics for the FHH, including a 52% increase in specific EA, a 45% enhancement in crushing load efficiency (CLE), and an 8% reduction in peak crushing force (PCF) compared to the conventional counterpart. Subsequently, this paper investigates the fractal arc honeycomb and evaluates the effect of the center angle on mechanical properties by varying its value. Furthermore, the mechanical properties of layered honeycomb and fractal honeycomb structures with different wall thicknesses are systematically examined. In the last section, we explore the theoretical analysis of the fractal-hexagonal honeycomb and find that the results of the theoretical analysis are in good agreement with those of the simulation, indicating that the experimental simulation results are reliable. Overall, the findings of this study offer valuable insights for the innovative design of hexagonal honeycomb structures, providing a reference for future advancements in this field. [ABSTRACT FROM AUTHOR]

Selective laser melting (SLM) forms specimens that often exhibit anisotropic mechanical properties. Most existing research only explains that the mechanical properties of specimens perpendicular to the build direction are superior to those parallel to the build direction. In this paper, the mechanical properties of SLM 316L SS specimens with different surfaces and different directions are compared. Finally, it was found that the mechanical properties of specimens on Face 3 are stronger than those on Face 1 and Face 2, while the mechanical properties of specimens on Face 1 and Face 2 are similar. For specimens in different directions on the same surface, the mechanical properties of Face 1 and Face 2 exhibit clear anisotropy, while the mechanical properties of Face 3 tend to be isotropic. In this paper, the EBSD technique was used to analyze the specimens. It was found that the anisotropy of the mechanical properties of Face 1 and Face 2 are attributed to the presence of texture and columnar crystals in the sample. This paper can provide accurate and reliable material performance data for the practical application of SLM 316L SS, thereby guiding the optimization of engineering design and manufacturing processes. [ABSTRACT FROM AUTHOR]

This article presents a comparative study of two types of transformer solid insulation: standard Kraft and thermally upgraded Kraft papers. The paper samples were impregnated with two different fluids, namely a synthetic dielectric ester fluid, Midel 7131, and a synthesized mineral oil, Luminol Tri. The impregnated papers were submitted to, accelerated aging at 150°C, temperature higher than the temperatures found inside transformers, for extended periods. The results show that for the first hours of aging, the cellulose depolymerization was similar for all the four studied cases. At a specific point, the paper samples aged in the ester fluid exhibited a lower depolymerization exceeding the 8000 hours of aging without reaching the levelling-off degree of polymerization (LODP). A similar trend was observed through the decrease of mechanical properties of papers in the ester-based oil. However, the difference in performance of both fluids was amplified due to the temperature used; at lower temperatures the difference should be smaller. Additionally, a relationship between the degree of polymerization and the mechanical properties accessed by the tensile testing was obtained regardless of the type of paper or oil. The total acidity in the ester fluid was higher than in mineral oil. Methanol, a chemical marker that is closely linked to the rupture of 1,4-ß-glycosidic bonds of cellulose, showed a partial sensitivity to the cellulose aging in the ester fluid. Furan (C4H4O) content was monitored during the aging and its concentration was found to be sensitive to the depolymerization along with the decrease in the mechanical properties of cellulose papers regardless of the type of paper. More importantly, its concentration was found to be dependent on the type of oil. More investigations are needed to further confirm the importance of furan as an indirect indicator of the mechanical performance along with its correlation with the depolymerization of paper aged in ester fluids. [ABSTRACT FROM AUTHOR]

The objective of this study was to investigate the influence of acetylation on properties of paper made using the chemi-mechanical pulp (CMP) process. Industrial unbleached CMP pulp was provided (before and after refining), and paper handsheets were made. After drying, the specimens were acetylated on a heated cylinder at 120 °C, with acetic anhydride without catalyst. Physical and mechanical properties including water absorption, porosity, printability, brightness, D-folding, breaking length, tear resistance, and burst strength of samples were measured and compared between treated samples and the controls. The results showed that acetylation intensity was increased by increasing reaction time. Water absorption exhibited a significant reduction due to acetylation. Brightness, D-folding, and burst showed an increasing trend as a function of the degree of acetylation. Tear resistance was decreased by acetylation. The refining process improved acetylation and decreased porosity. The results indicated that most of the important factors were significantly influenced and improved by both acetylation and the refining process. [ABSTRACT FROM AUTHOR]

Developing 3D printable waste paper based biocomposites is a potentially greener alternative to traditional waste paper recycling methods. In this paper, waste office paper (WOP) filled polylactide acid (PLA) biocomposites were prepared as filaments for Fused Filament Fabrication (FFF). The morphology, rheology, thermal properties, and physical properties of PLA-WOP composites were investigated. Results revealed that the addition of WOP improved the composites' melt flow abilities. The T g and T m of composites remained similar to the neat PLA. However, tensile strengths of the prints decreased with the increase of WOP content, which could be attributed to the heterogeneous dispersion and aggregation caused by the abundance of WOP in the system. When 5% WOP was used, the elongation at break increased in comparison with pure PLA specimens. Nonetheless, when the WOP content was increased to 15%, the elongation at break decreased. To improve the mechanical properties of the prints, a silane coupling agent (γ-methacryloxypropyltrimethoxylsilane, KH570) was used to modify WOP granules. The mechanical properties were clearly enhanced post KH570 treatment. Furthermore, FTIR analyses demonstrated that the hydrogen bonding improved interfacial adhesion between WOP fillers and the PLA matrix. Thermal decomposition showed that the PLA-WOP composites had virtually no degradation below 260 °C, indicating that the composite filaments are safe for indoor 3D printing. [ABSTRACT FROM AUTHOR]

In this study, the multifunctionality of structural dielectric capacitor made by integrating graphene oxide paper into carbon fibre reinforced composite has been investigated. The study is based on an earlier work on the use of graphene oxide for dielectric material in the structural dielectric capacitor, in which electrical properties have been characterized. In this work, an in-depth study on electrical and mechanical properties of this kind of structural dielectric capacitor have been carried out. In addition, the multifunctional efficiency of structural dielectric capacitors were evaluated and compared with existing structural dielectric capacitors. Through experiments, it is revealed that both electrical and mechanical properties of the structural dielectric capacitors were significantly enhanced by interleaving a graphene oxide paper in the middle of composite. Therefore, the multifunctional efficiency of this kind of structural dielectric capacitors has been ultimately improved, indicating the excellent potential of graphene oxide paper in the development of multifunctional materials for energy storage, potentially for high-strength required applications, such as electric vehicles and unmanned aerial vehicles. [ABSTRACT FROM AUTHOR]

Nanostructured materials are difficult to prepare rapidly and at large scale. Melt-processed polymer-clay nanocomposites are an exception, but the clay content is typically below 5 wt%. An approach for manufacturing of microfibrillated cellulose (MFC)/kaolinite nanocomposites is here demonstrated in pilot-scale by continuous production of hybrid nanopaper structures with thickness of around 100 μm. The colloidal nature of MFC suspensions disintegrated from chemical wood fiber pulp offers the possibility to add kaolinite clay platelet particles of nanoscale thickness. For initial lab scale optimization purposes, nanocomposite processing (dewatering, small particle retention etc) and characterization (mechanical properties, density etc) were investigated using a sheet former (Rapid Köthen). This was followed by a continuous fabrication of composite paper structures using a pilot-scale web former. Nanocomposite morphology was assessed by scanning electron microscopy (SEM). Mechanical properties were measured in uniaxial tension. The fire retardancy was evaluated by cone calorimetry. Inorganic hybrid composites with high content of in-plane oriented nanocellulose, nanoclay and wood fibers were successfully produced at pilot scale. Potential applications include fire retardant paperboard for semi structural applications and as reinforcement mats in molded thermoset biocomposites. [ABSTRACT FROM AUTHOR]

The ceramic materials studied in this paper consist of finely dispersed crystalline phases embedded in a glassy matrix, which is similar to glass-ceramic materials, porcelain, and VC products. The strength depends then not only on the properties of the individual crystalline phases but also on their interactions and the matrix. Differences in mechanical properties for materials with similar chemical compositions are most likely related to diverging microstructures. Crystal orientation, grain-size distribution and shape, the ratio of the glass matrix to the crystalline phase, and homogeneity control the flexural strength of glass-ceramic materials. The subject of the study is whiteware ceramic materials from the SiO 2 –Al 2 O 3 –Na 2 O–K 2 O–MgO–SrO system, fired similarly to the regime used for VC products. The effect of the type of alkali oxide and the share of SrO were tested. This paper presents the results of hot-stage microscopy, X-ray diffraction (XRD), scanning electron microscopy with a micro-analyzer (SEM-EDS) and biaxial flexural strength measurements. Additionally, nanoindentation technique was used to access local mechanical properties. [ABSTRACT FROM AUTHOR]

The accelerated ageing of wood in terms of heating or iron rusting has a potential effect on the physio-mechanical, chemical and biological properties of wood. The effects of accelerated ageing on the mechanical, physical and fungal activity properties of some wood materials (Schinus terebinthifolius, Erythrina humeana, Tectona grandis, Pinus rigida and Juglans nigra) were studied after several cycles of heating and iron rusting. The fungal activity was assayed against the growth of Aspergillus terreus, Aspergillus niger, Fusarium culmorum and Stemphylium solani. In addition, the mechanical and optical properties of paper sheets produced from those wood pulps by means of Kraft cooking were evaluated. The mechanical and chemical properties of the studied wood species were affected significantly (p < 0.05) by the accelerated ageing, compared to control woods. With Fourier transform infrared (FTIR) spectroscopy, we detected an increase in the intensity of the spectra of the functional groups of cellulose in the heated samples, which indicates an increase in cellulose content and decrease in lignin content, compared to other chemical compounds. For pulp properties, woods treated by heating showed a decrease in the pulp yield. The highest significant values of tensile strength were observed in pulp paper produced from untreated, heated and iron-rusted P. rigida wood and they were 69.66, 65.66 and 68.33 N·m/g, respectively; we calculated the tear resistance from pulp paper of untreated P. rigida (8.68 mN·m2/g) and T. grandis (7.83 mN·m2/g) and rusted P. rigida (7.56 mN·m2/g) wood; we obtained the values of the burst strength of the pulp paper of untreated woods of P. rigida (8.19 kPa·m2/g) and T. grandis (7.49 kPa·m2/g), as well as the fold number of the pulp paper of untreated, heated and rusted woods from P. rigida, with values of 195.66, 186.33 and 185.66, respectively. After 14 days from the incubation, no fungal inhibition zones were observed. Accelerated ageing (heated or iron-rusted) produced significant effects on the mechanical and chemical properties of the studied wood species and affected the properties of the produced pulp paper. [ABSTRACT FROM AUTHOR]

The mechanical loads that gas diffusion layers (GDLs) withstand in polymer electrolyte membrane fuel cell (PEMFC) stacks are sensitive to the assembly and working conditions. The mechanical properties of GDLs mostly depend on their composition materials, microstructural characteristics, operation conditions, etc. An accurate and comprehensive understanding of the mechanical performance of GDLs is significant for predicting the stress distribution and improving the assembly technology of PEMFC stacks. This study presented a novel 3-D nonlinear and orthotropic constitutive model of a carbon paper GDL to represent the material stiffness matrix with its compressive, tensile, and shear properties. Numerical simulations were performed based on the 3-D constitutive model, and the proposed 3-D model was validated against the experimental data reported previously. It is found that the simulation results of the 3-D constitutive model show a good agreement with the experimental results. Besides, the novel 3-D nonlinear and orthotropic model was applied in the overall stress simulation of a simplified PEMFC unit cell, compared to a conventional 3-D linear and isotropic model, and the simulation results of the two models show a significant difference. [ABSTRACT FROM AUTHOR]

Ultra-high-performance concrete (UHPC) is a cementitious composite combining high-strength concrete matrix and fiber reinforcement. Standing out for its excellent mechanical properties and durability, this material has been widely recognized as a viable choice for highly complex engineering projects. This paper proposes (i) the review of the influence exerted by the constituent materials on the mechanical properties of compressive strength, flexural tensile strength, and elastic modulus of UHPC and (ii) the determination of optimal quantities of the constituent materials based on simplified statistical analyses of the developed database. The data search was restricted to papers that produced UHPC with straight steel fibers at a content of 2% by volume. UHPC mixture models were proposed based on graphical analyses of the relationship of constituent materials versus mechanical properties, aiming to optimize the material's performance for each mechanical property. The results proved to be in accordance with the specifications present in the literature, characterized by high cement consumption, significant presence of fine materials, and low water-to-binder ratio. The divergences identified between the mixtures reflect how the constituent materials uniquely impact each mechanical property of the concrete. In general, fine materials were shown to play a significant role in increasing the compressive strength and flexural tensile strength of UHPC, while water and superplasticizers stood out for their influence on the material's workability. [ABSTRACT FROM AUTHOR]