Search

Copyright of Polimery is the property of Industrial Chemistry Research Institute and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Abstract Three novel Schiff base polymers were synthesized by using the Schiff base monomer obtained using aldehyde containing boric acid and amines containing hydroxyl groups as the starting materials. The polymers were synthesized at the same temperature and using the same amount of oxidizing agent by the oxidative polycondensation method. The characterization of all polymers and monomers was achieved by using Fourier transform infrared spectroscopy (FT-IR), ultraviolet–visible spectroscopy (UV–vis), nuclear magnetic resonance spectroscopy (1H-NMR), liquid chromatography-mass spectrometry (LC–MS), gel permeation chromatography (GPC) and scanning electron microscopy (SEM). The thermal stability of these compounds was studied by employing thermogravimetric analysis (TGA), and thermodynamics parameters such as activation energy (Ea), enthalpy (∆H), entropy (∆S), and Gibbs free energy(∆G) for the decomposition process were calculated using the Flynn–Wall–Ozawa method.

Current highly integrated devices require heat interface materials with excellent heat conductivity. A simple approach was employed to synthesize thermally conductive and outstanding thermal stability nanocomposite. Calcium carbonate nanoparticles (nano CaCO 3) reinforced with reduced graphene oxide (rGO) nanoparticles (rGO/CaCO 3) are synthesized using a novel process, and the effect of rGO in CaCO 3 structure is examined by Field Emission Scanning Electron Microscope, X-ray diffraction, TGA-DTA, and thermal conductivity. The experimental results show that adding rGO resulted in higher crystallinity and thermal stability. As the wt.% of rGO increases from 1 to 5%, the crystallite size was suppressed by 21.06%, 27.39%, 32.48%, 41.5%, and 45.30%, respectively, compared to the pure nano-CaCO 3. Additionally, rGO enhances the thermal conductivity by 35.31% and thermal diffusivity to 1.834 mm2/s by adding 5% rGO. [ABSTRACT FROM AUTHOR]

In this work, we present the effect of graphene nanoplatelets (GnPs) modification with ionic liquids (ILs). The textural properties of graphene nanoplatelets (GnPs) used as styrene-butadiene rubber's filler and the thermal properties of the composites obtained with the use of the mentioned fillers were investigated. GnPs were modified with 1-butylpyridinium bromide (BPyBr) and 4-methyl-1-butylpyridinium bromide (BmPyBr) through two different ways. One strategy has been to deposit the filler modifier from the solution. The second one involved the modification of the filler with ionic liquids in bulk during the preparation of elastomer blends. Settlement of the proposed ionic liquids onto the GnPs' surface led to significant changes in the textural characteristics. BPyBr has restricted the filler's microporosity, whereas BmPyBr has caused the formation of a more opened filler structure without the increase in its average pore size. GnPs modified with ILs led to reducing the temperature of vulcanization of SBR compounds and affected the thermal stability of the composites. [ABSTRACT FROM AUTHOR]

By using the aerodynamic levitation and laser melting technique to well extend the glass‐forming region into the Mg‐rich and peraluminous regime, a series of magnesium aluminosilicate glasses were prepared to investigate the Mg and Al mixed effects on thermal properties, including glass transition temperature (Tg), crystallization behavior, and thermal stability. With the gradual substitution of Mg by Al, Tg exhibits two types of near‐linear rises with different slopes in two compositional regions separated by r = 0.57, where r is equal to the molar ratio of [Al2O3]/([Al2O3] + [MgO]). Moreover, when it comes to other properties, that is, crystallization behavior and thermal stability, this critical point precisely appears at the same r = 0.57. Compared to the slower increase of Tg in Mg‐rich region, the steeper rise of Tg in the peraluminous region is mainly ascribed to the step‐by‐step formation of oxygen triclusters driven by Pauling's second rule. Moreover, the occurrence of the critical point for Tg rise at r = 0.57 rather than the theoretical 0.5 can be seen as a proof of the role of Mg cations partly as a network former. [ABSTRACT FROM AUTHOR]

In the present work, hybrid nanobiocomposites based on poly(3-hydroxybutyrate), P3HB, with the use of aromatic linear polyurethane as modifier and organic nanoclay, Cloisite 30B, as a nanofiller were produced. The aromatic linear polyurethane (PU) was synthesized in a reaction of diphenylmethane 4,4′-diisocyanate and polyethylene glycol with a molecular mass of 1000 g/mole. The obtained nanobiocomposites were characterized by the small-angle X-ray scattering technique, scanning electron microscopy, Fourier infrared spectroscopy, thermogravimetry, and differential scanning calorimetry, and moreover, their selected mechanical properties, biodegradability, and cytotoxicity were tested. The effect of the organomodified montmorillonite presence in the biocomposites on their properties was investigated and compared to those of the native P3HB and the P3HB-PU composition. The obtained hybrid nanobiocomposites have an exfoliated structure. The presence and content of Cloisite 30B influence the P3HB-PU composition's properties, and 2 wt.% Cloisite 30B leads to the best improvement in the aforementioned properties. The obtained results indicate that the thermal stability and mechanical properties of P3HB were improved, particularly in terms of increasing the degradation temperature, reducing hardness, and increasing impact strength, which were also confirmed by the morphological analysis of these bionanocomposites. However, the presence of organomodified montmorillonite in the obtained polymer biocomposites decreased their biodegradability slightly. The produced hybrid polymer nanobiocomposites have tailored mechanical and thermal properties and processing conditions for their expected application in the production of biodegradable, short-lived products for agriculture. Moreover, in vitro studies on human skin fibroblasts and keratinocytes showed their satisfactory biocompatibility and low cytotoxicity, which make them safe when in contact with the human body, for instance, in biomedical applications. [ABSTRACT FROM AUTHOR]

Abstract This work is an attempt to develop flexible radiation shielding based on a blend of polymethyl methacrylate (PMMA)/polyvinyl acetate (PVAc) and LaFeO3 nanoparticles (NPs). LaFeO3 and LaFeO3/PMMA/PVAc were made using simple chemical techniques. A high-resolution transmission electron microscope (HR-TEM) and X-ray diffraction (XRD) showed that well-crystallized LaFeO3 NPs with particles 79 nm in size and an orthorhombic shape were obtained. In addition, XRD confirmed the existence of PMMA, PVAc, and LaFeO3 in the nanocomposite films. Fourier transform infrared (FTIR) confirmed that the LaFeO3 NPs and the reactive functional groups in the blend interacted with each other. Field emission-scan electron microscope (FE-SEM) analysis showed that PMMA and PVAc form a homogenous blend and that the LaFeO3 NPs were spread out inside and on the blend surface. The samples showed transmittance in the range of 30–74% and a small extinction coefficient (≤ 0.08). The samples exhibited a dual-band gap structure, and the direct (indirect) band gap shrank from 5.1 to 4.7 eV (4.9 to 4.4 eV). The thermal analyses showed that the samples are thermally stable up to 260 °C. The Phy-X/PSD software was used to figure out the theoretical gamma-ray attenuation parameters, such as the mass attenuation coefficient, the mean free path, and the half-value layer, for different PMMA/PVAc + x% LaFeO3 composites. It is demonstrated that the PMMA/PVAc + 10 wt% LaFeO3 sample exhibits much better shielding effectiveness than PMMA/PVAc, and hence it is suitable for protecting against radiation.

Abstract L‐ and D‐ form oligo(lactic acid)s (OLLA and ODLA) grafted α‐cellulose (OLLA‐g‐cellulose and ODLA‐g‐cellulose) were prepared by the graft polycondensation reaction in C6H5CH3 medium at 130°C and 380 mm of mercury pressure. Para‐toluene sulphonic acid (5 wt% of oligo(lactic acid)) was used as a catalyst whereas potassium persulfate (0.01 wt% of oligo(lactic acid)) was used as a co‐catalyst in the graft polycondensation reaction. OLLA and ODLA with a degree of polymerization (DP) 6–7 used in polycondensation reaction were also prepared by ring‐opening polymerization of L‐ and D‐lactides at 140°C for 10 h with stannous octoate (C16H30O4Sn) as a motivator, L, and D monomer of lactic acids as co‐motivators. FTIR analysis proved the bonding of OLLA and ODLA onto the α‐cellulose surface. The thermal properties of poly(L‐lactic) acid (PLLA) composites were explored by thermal analysis (TG, DTA, and DTG). Degradation, melting, and maximum weight loss temperature of the composites were increased with the increase of grafted cellulose up to 10% and then decreased. TG and DTA results showed that the incorporation of grafted α‐cellulose (grafted cellulose) can improve the thermal properties of PLLA composites. Highlights Synthesis of oligo(lactic acid)s from L‐ and D‐lactides by ring‐opening polymerization reactions. α‐cellulose extraction and graft modification with oligo(lactic acid)s. Preparation of grafted α‐cellulose composite with PLLA matrix. Evaluation of thermal properties of the grafted α‐cellulose‐reinforced composites.

In this paper, polystyrene (PS)-based reduced graphene oxide (rGO) composites were prepared by mixing PS latex particles with graphene oxide (GO) and the following in-situ reduction. The structure and morphology of PS/rGO composites were characterized, and the effects of rGO content on the dielectric properties as well as thermal stability of PS/rGO composites were investigated. Results showed that rGO sheets armoured on the surface of PS particles and exhibited well dispersion in the PS matrix after hot compression. The introduction of rGO improved the dielectric properties of the composites remarkably. When rGO content was 0.12 vol%, the dielectric permittivity and breakdown strength of PS/rGO arrived at 6.3 at102 Hz and 107 kV/mm, with 50% and 35.4% enhancement compared to the pristine PS. Furthermore, PS/rGO presented better thermal stability than the pristine PS, but the overlapping of rGO sheets in PS matrix induced the instability of dielectric loss with frequency. [ABSTRACT FROM AUTHOR]

Some photosensitive resins have poor mechanical properties after 3D printing. To overcome these limitations, a polyurethane acrylate oligomer (PUA) microsphere was prepared using the Pickering emulsion template method and ultraviolet (UV) curing technology in this paper. The prepared PUA microspheres were added to PUA-1,6-hexanediol diacrylate (HDDA) photosensitive resin system for digital light processing (DLP) 3D printing technology. The preparation process of PUA microspheres was discussed based on micromorphology, and it was found that the oil-water ratio of the Pickering emulsion and the emulsification speed had a certain effect on the microsphere size. As the oil-water ratio and the emulsification speed increased, the microsphere particle size decreased to a certain extent. Adding a suitable proportion of PUA microspheres to the photosensitive resin can improve the mechanical properties and thermal stability. When the modified photosensitive resin microsphere content was 0.5%, the tensile strength, elongation at break, bending strength, and initial thermal decomposition temperature were increased by 79.14%, 47.26%, 26.69%, and 10.65%, respectively, compared with the unmodified photosensitive resin. This study provides a new way to improve the mechanical properties of photosensitive resin 3D printing. The resin materials studied in this work have potential application value in the fields of ceramic 3D printing and dental temporary replacement materials. [ABSTRACT FROM AUTHOR]

In the present work, hybrid nanobiocomposites based on poly(3-hydroxybutyrate), P3HB, with the use of aromatic linear polyurethane as modifier and organic nanoclay, Cloisite 30B, as a nanofiller were produced. The aromatic linear polyurethane (PU) was synthesized in a reaction of diphenylmethane 4,4′-diisocyanate and polyethylene glycol with a molecular mass of 1000 g/mole. The obtained nanobiocomposites were characterized by the small-angle X-ray scattering technique, scanning electron microscopy, Fourier infrared spectroscopy, thermogravimetry, and differential scanning calorimetry, and moreover, their selected mechanical properties, biodegradability, and cytotoxicity were tested. The effect of the organomodified montmorillonite presence in the biocomposites on their properties was investigated and compared to those of the native P3HB and the P3HB-PU composition. The obtained hybrid nanobiocomposites have an exfoliated structure. The presence and content of Cloisite 30B influence the P3HB-PU composition’s properties, and 2 wt.% Cloisite 30B leads to the best improvement in the aforementioned properties. The obtained results indicate that the thermal stability and mechanical properties of P3HB were improved, particularly in terms of increasing the degradation temperature, reducing hardness, and increasing impact strength, which were also confirmed by the morphological analysis of these bionanocomposites. However, the presence of organomodified montmorillonite in the obtained polymer biocomposites decreased their biodegradability slightly. The produced hybrid polymer nanobiocomposites have tailored mechanical and thermal properties and processing conditions for their expected application in the production of biodegradable, short-lived products for agriculture. Moreover, in vitro studies on human skin fibroblasts and keratinocytes showed their satisfactory biocompatibility and low cytotoxicity, which make them safe when in contact with the human body, for instance, in biomedical applications.

In recent decades, fiber membranes have garnered significant attention and found numerous applications across various fields. This work used the electrospinning method to create fiber membranes with cellulose acetate (CA) as a primary polymer material. The characteristics of the fiber membrane, such as mechanical and thermal properties, were investigated by incorporating Pahae Natural Zeolite (PNZ) microparticles into the CA matrix. The fiber membranes' mechanical properties are improved by adding PNZ to the CA matrix, and the CA/PNZ 10% exhibits the maximum tensile strength of 0.97 MPa and elongation at a break of 4.52%. Meanwhile, incorporating PNZ filler into CA fiber membranes significantly enhances their thermal stability. This improvement is attributed to the formation of hydrogen bonds between CA and PNZ, as evidenced by the increasing residue values with higher PNZ content. Specifically, the residue of pure CA membrane fiber is 13.46%, which increases to 44.06% for CA/PNZ 15% fiber membranes. These favorable thermal and mechanical properties of the fiber membranes indicate the promising potential of CA/PNZ-based membranes for filtration applications. [ABSTRACT FROM AUTHOR]

In this paper, polystyrene (PS)-based reduced graphene oxide (rGO) composites were prepared by mixing PS latex particles with graphene oxide (GO) and the following in-situ reduction. The structure and morphology of PS/rGO composites were characterized, and the effects of rGO content on the dielectric properties as well as thermal stability of PS/rGO composites were investigated. Results showed that rGO sheets armoured on the surface of PS particles and exhibited well dispersion in the PS matrix after hot compression. The introduction of rGO improved the dielectric properties of the composites remarkably. When rGO content was 0.12 vol%, the dielectric permittivity and breakdown strength of PS/rGO arrived at 6.3 at102 Hz and 107 kV/mm, with 50% and 35.4% enhancement compared to the pristine PS. Furthermore, PS/rGO presented better thermal stability than the pristine PS, but the overlapping of rGO sheets in PS matrix induced the instability of dielectric loss with frequency.

The bisphenol A-type phthalonitrile (BAPH) was blended with the classic epoxy system E51/DDS to prepare the epoxy/phthalonitrile thermoset. The curing kinetics were investigated by differential scanning calorimetry (DSC) using the isoconversional principle, and the average activation energy (Eα) of the E51/DDS curing reaction was found to decrease from 87 kJ/mol to 68.6 kJ/mol. Combining the results of the rheological study, the promoting effect of phthalonitrile on the crosslink of epoxy/amine is confirmed. The curing reaction of the blended resin was characterized using FTIR, and the results showed that BAPH could react with DDS. The thermal behaviors of the thermosets were investigated via DMA and TGA. The glass transition temperature (Tg) is found to increase from 181 °C to 195 °C. The char yield increases from 16% to 59.6% at 800 °C in a N2 atmosphere, which is higher than the calculated value based on the proportional principle. The AFM phase images show that there is no phase separation in the cured thermoset. The results imply that the cured epoxy/amine/phthalonitrile blend is probably a kind of copolymer. The real-time TG-MS indicated that the pyrolysis of the thermoset can be divided into two relatively independent stages, which can be assigned to the cleavage of the E51/DDS network, and the phthalocyanine/triazine/isoindoline, respectively.

Amphiphilic block copolymers of N-vinyl pyrrolidone (NVP) and various vinyl esters (VEs), PNVP-b-PVEs, namely vinyl butyrate (VBu), vinyl decanoate (VDc), and vinyl stearate (VSt), were synthesized through RAFT polymerization techniques. The sequential addition of the monomers methodology was employed starting from the polymerization of NVP followed by the polymerization of the Ves’ monomer. The polymerization of NVP was conducted at 60 °C in benzene solution using AIBN as the initiator and O-ethyl S-(phthalimidylmethyl) xanthate as the CTA. The resulting PNVP macro-CTA was further applied for the polymerization of the vinyl ester in dioxane solution at 80 °C using, again, AIBN as the initiator. The block copolymers were characterized through size-exclusion chromatography (SEC) and NMR spectroscopy. The thermal behavior of the copolymers was studied by Differential Scanning Calorimetry (DSC), whereas their thermal stability via Thermogravimetric Analysis (TGA) and Differential Thermogravimetry (DTG).

Melt-quenching techniques were employed to produce a series of Nd 2 O 3 doped Al 2 O 3 –Na 2 O–WO 3 –B 2 O 3 glasses. Structure, optical, and thermal properties were investigated to illustrate the effectiveness of the Nd3+ ions in enhancement performance and analyze their behaviour. Nd 2 O 3 demonstrably contributed to the composite, as evidenced by evaluating all features. The density marginally rises with the addition of Nd 2 O 3 instead of B 2 O 3. The relevant physical characteristics had been calculated. The structure was analyzed by FTIR measurement and identified the vibration modes of varied concentrations. From FTIR spectra, N 4 values were reckoned, and the conversion of the network structure unit from BO 3 to BO 4 was verified. Numerous significant peaks have been caught in the absorption bands of the UV–Vis–NIR measurement. Optical bandgap and band tail are determined. DSC measurements were utilized to identify the thermal characteristics. As Nd3+ ions increased, glass thermal stability improved. Overall, the Nd3+ ion modifier rule was realized. [ABSTRACT FROM AUTHOR]

In this research work, we aim to study the effect of the incorporation of vegetable fiber reinforcement on the thermo-mechanical and dynamic properties of a composite formed by a polymeric matrix reinforced with cellulosic fibers with the various Washingtonia fiber (WF) loadings (0%, 10%, 20%, and 30% by wt%) as reinforced material in high-density polyethylene (HDPE) Biocomposites to evaluate the optimum fiber loading of biocomposites. In addition, several characterization techniques (i.e., thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and thermal mechanical analysis (TMA)) were used to better understand the characteristics of the new composites prepared. With these techniques, we managed to verify the rigidity and thermal stability of the composites so elaborated, as well as the success of the polymer and the structural homogeneity of the obtained biocomposites. Hence, the biocomposite with the best ratio (HDPE/20WF) showed a loss modulus (E″) of 224 MPa, a storage modulus (E′) of 2079 MPa, and a damping factor (Tanδ) of 0.270 to the glass transition (Tg) of 145 °C. In addition, thermomechanical analysis (TMA) of the biocomposite samples exhibited marginally higher Ts compared to the HDPE matrix. The best results were recorded with biocomposites with 20% WF, which showed better thermal properties. This composite material can be used as insulation in construction materials (buildings, false ceilings, walls, etc.). [ABSTRACT FROM AUTHOR]

Aging of polymers is a natural process that occurs during their usage and storage. Predicting the lifetime of polymers is a crucial aspect that should be considered at the design stage. In this paper, a series of bio-based thermoplastic poly(ether-urethane) elastomers (bio-TPUs) with modified hard segments were synthesized and investigated to understand the structural and property changes triggered by accelerated aging. The bio-TPUs were synthesized at an equimolar ratio of reagents using the prepolymer method with the use of bio-based poly(trimethylene ether) glycol, bio-based 1,3-propanediol, and hexamethylene diisocyanate or hexamethylene diisocyanate/partially bio-based diisocyanate mixtures. The polymerization reaction was catalyzed by dibutyltin dilaurate (DBTDL). The structural and property changes after accelerated aging under thermal and hydrothermal conditions were determined using Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and dynamic mechanical thermal analysis (DMTA). Among other findings, it was observed that both the reference and aged bio-TPUs decomposed in two main stages and exhibited thermal stability up to approximately 300 °C. Based on the research conducted, it was found that accelerated aging impacts the supramolecular structure of TPUs.

Scholars are looking for solutions to substitute hazardous substances in manufacturing nanocellulose from bio-sources to preserve the world’s growing environmental consciousness. During the past decade, there has been a notable increase in the use of cellulose nanocrystals (CNCs) in modern science and nanotechnology advancements because of their abundance, biocompatibility, biodegradability, renewability, and superior mechanical properties. Spherical cellulose nanocrystals (J–CNCs) were successfully synthesized from Jenfokie micro-cellulose (J–MC) via sulfuric acid hydrolysis in this study. The yield (up to 58.6%) and specific surface area (up to 99.64 m2/g) of J–CNCs were measured. A field emission gun–scanning electron microscope (FEG-SEM) was used to assess the morphology of the J–MC and J–CNC samples. The spherical shape nanoparticles with a mean nano-size of 34 nm for J–CNCs were characterized using a transmission electron microscope (TEM). X-ray diffraction (XRD) was used to determine the crystallinity index and crystallinity size of J–CNCs, up to 98.4% and 6.13 nm, respectively. The chemical composition was determined using a Fourier transform infrared (FT–IR) spectroscope. Thermal characterization of thermogravimetry analysis (TGA), derivative thermogravimetry (DTG), and differential thermal analysis (DTA) was conducted to identify the thermal stability and cellulose pyrolysis behavior of both J–MC and J–CNC samples. The thermal analysis of J–CNC indicated lower thermal stability than J–MC. It was noted that J–CNC showed higher levels of crystallinity and larger crystallite sizes than J–MC, indicating a successful digestion and an improvement of the main crystalline structure of cellulose. The X-ray diffraction spectra and TEM images were utilized to establish that the nanocrystals’ size was suitable. The novelty of this work is the synthesis of spherical nanocellulose with better properties, chosen with a rich source of cellulose from an affordable new plant (studied for the first time) by stepwise water-retted extraction, continuing from our previous study.

Polymer nanocomposites, which combine the advantages of polymers and fillers, are widely used in the field of automobile and aviation. Polyimine (PI) is an emerging thermoset material with remarkable properties, such as malleability, recyclability, and self-healing. Silicon carbide nano-whiskers (SiCw), as a cheap and high-hardness filler material, are chosen to enhance the properties of polyimine matrix. Silicon carbide nano-whisker-reinforced polyimine (PI-SiCw) nanocomposites were successfully fabricated by heat pressing, which was confirmed by FTIR and XPS tests. According to the results of mechanical tests, the mechanical properties of PI-SiCw nanocomposites were obviously improved. For example, with the addition of 0.5% SiCw, bending strength and bending elongation at break can be simultaneously increased by 33% and 148%, respectively. Surprisingly, the impact strength of PI-SiCw nanocomposites with 2% SiCw was increased by 154% compared to the matrix. SEM and EDS tests showed that the evenly distributed SiCw in the polyimine matrix enhanced the mechanical properties of PI-SiCw nanocomposites according to the mechanism of whiskers pulling out and the bridging principle. According to the TGA test results, the PI composites with SiCw retain a higher weight percentage at 800 °C. The reason was the combined effect of the good thermal stability of SiCw and their strong interactions with the PI matrix. As a result, introducing SiCw into the PI matrix imparts a slight improvement in thermal stability. This article presents an avenue of cost-effective research to enhance the mechanical properties of polyimine composites. [ABSTRACT FROM AUTHOR]

Scholars are looking for solutions to substitute hazardous substances in manufacturing nanocellulose from bio-sources to preserve the world's growing environmental consciousness. During the past decade, there has been a notable increase in the use of cellulose nanocrystals (CNCs) in modern science and nanotechnology advancements because of their abundance, biocompatibility, biodegradability, renewability, and superior mechanical properties. Spherical cellulose nanocrystals (J–CNCs) were successfully synthesized from Jenfokie micro-cellulose (J–MC) via sulfuric acid hydrolysis in this study. The yield (up to 58.6%) and specific surface area (up to 99.64 m2/g) of J–CNCs were measured. A field emission gun–scanning electron microscope (FEG-SEM) was used to assess the morphology of the J–MC and J–CNC samples. The spherical shape nanoparticles with a mean nano-size of 34 nm for J–CNCs were characterized using a transmission electron microscope (TEM). X-ray diffraction (XRD) was used to determine the crystallinity index and crystallinity size of J–CNCs, up to 98.4% and 6.13 nm, respectively. The chemical composition was determined using a Fourier transform infrared (FT–IR) spectroscope. Thermal characterization of thermogravimetry analysis (TGA), derivative thermogravimetry (DTG), and differential thermal analysis (DTA) was conducted to identify the thermal stability and cellulose pyrolysis behavior of both J–MC and J–CNC samples. The thermal analysis of J–CNC indicated lower thermal stability than J–MC. It was noted that J–CNC showed higher levels of crystallinity and larger crystallite sizes than J–MC, indicating a successful digestion and an improvement of the main crystalline structure of cellulose. The X-ray diffraction spectra and TEM images were utilized to establish that the nanocrystals' size was suitable. The novelty of this work is the synthesis of spherical nanocellulose with better properties, chosen with a rich source of cellulose from an affordable new plant (studied for the first time) by stepwise water-retted extraction, continuing from our previous study. [ABSTRACT FROM AUTHOR]

The experimental studies on the thermal properties and decomposition course of a novel class of potential anticancer drugs (1–5) containing in their heterobicyclic structures the asymmetrical triazine template were performed with the use of differential scanning calorimetry (DSC) and simultaneous thermogravimetry/differential scanning calorimetry (TG/DTG/DSC) coupled online with Fourier transform infrared spectroscopy (FTIR) and quadrupole mass spectrometry (QMS) in inert and oxidizing conditions. All the compounds were thermally characterized in detail for the first time in this article. The DSC studies proved that the melting points of the tested compounds depended on the position and type of the substituent at the phenyl moiety, whereas they did not depend on the furnace atmosphere. All the tested polynitrogenated heterocycles proved to be molecules with high thermal stability in both atmospheres, and most of them (1, 3–5) were more stable in oxidizing conditions, which indicated the formation of a more thermally stable form of the compounds when interacting with oxygen. The simultaneous TG/FTIR/QMS analyses confirmed that their pyrolysis process occurred in one main stage resulting in the emission of volatiles such as NH3, HNCO, HCN, CO, CO2, H2O, NO2, aromatic amine derivatives, alkenes (for compounds 1–5), and HCl (for the compound 5). On the other hand, the oxidative decomposition process was more complicated and proceeded in two main stages leading to the emission of NH3, CO2, CO, HCN, HNCO, H2O, some aromatics (for compounds 1–5), HCl (for compounds 3–5) as well as the additional volatiles such as N2, NO2, NH2OH, and (CN)2. The type of the formed volatiles indicated that the decomposition process of the studied heterocycles under the influence of heating was initiated by the radical mechanism. Their decomposition was related to the symmetric cleavage of C–N and C–C bonds (inert conditions) and additional reaction of the volatiles and residues with oxygen (oxidizing conditions). [ABSTRACT FROM AUTHOR]

This article explores wood-fiber-based fabrics containing Lyocell yarn in the warp and Spinnova–Lyocell (60%/40%) yarn in the weft, which are used to form unidirectional all-cellulose composites (ACC) through partial dilution in a NaOH–urea solution. The aim is to investigate the role of the yarn orientation in composites, which was conducted by measuring the tensile properties in both the 0° and 90° directions. As a reference, thermoplastic biocomposites were prepared from the same fabrics, with biobased polypropylene (PP) as the matrix. We also compared the mechanical and thermal properties of the ACC and PP biocomposites. The following experiments were carried out: tensile test, TGA, DSC, DMA, water absorption test and SEM. The study found no significant difference in tensile strength regarding the Spinnova–Lyocell orientation between ACC and PP biocomposites, while the composite tensile strength was clearly higher in the warp (Lyocell) direction for both composite variants. Elongation at break doubled in ACC in the Lyocell direction compared with the other samples. Thermal analysis showed that mass reduction started at a lower temperature for ACC, but the thermal stability was higher compared with the PP biocomposites. Maximum thermal degradation temperature was measured as being 352 °C for ACC and 466 °C for neat PP, and the PP biocomposites had two peaks in the same temperature range (340–474 °C) as ACC and neat PP combined. ACCs absorbed 93% of their own dry weight in water in just one hour, whereas the PP biocomposites BC2 and BC4 absorbed only 10% and 6%, respectively. The study highlights the different properties of ACC and PP reference biocomposites that could lead to further development and research of commercial applications for ACC. [ABSTRACT FROM AUTHOR]

The bisphenol A-type phthalonitrile (BAPH) was blended with the classic epoxy system E51/DDS to prepare the epoxy/phthalonitrile thermoset. The curing kinetics were investigated by differential scanning calorimetry (DSC) using the isoconversional principle, and the average activation energy (Eα) of the E51/DDS curing reaction was found to decrease from 87 kJ/mol to 68.6 kJ/mol. Combining the results of the rheological study, the promoting effect of phthalonitrile on the crosslink of epoxy/amine is confirmed. The curing reaction of the blended resin was characterized using FTIR, and the results showed that BAPH could react with DDS. The thermal behaviors of the thermosets were investigated via DMA and TGA. The glass transition temperature (Tg) is found to increase from 181 °C to 195 °C. The char yield increases from 16% to 59.6% at 800 °C in a N2 atmosphere, which is higher than the calculated value based on the proportional principle. The AFM phase images show that there is no phase separation in the cured thermoset. The results imply that the cured epoxy/amine/phthalonitrile blend is probably a kind of copolymer. The real-time TG-MS indicated that the pyrolysis of the thermoset can be divided into two relatively independent stages, which can be assigned to the cleavage of the E51/DDS network, and the phthalocyanine/triazine/isoindoline, respectively. [ABSTRACT FROM AUTHOR]

Amphiphilic block copolymers of N-vinyl pyrrolidone (NVP) and various vinyl esters (VEs), PNVP-b-PVEs, namely vinyl butyrate (VBu), vinyl decanoate (VDc), and vinyl stearate (VSt), were synthesized through RAFT polymerization techniques. The sequential addition of the monomers methodology was employed starting from the polymerization of NVP followed by the polymerization of the Ves' monomer. The polymerization of NVP was conducted at 60 °C in benzene solution using AIBN as the initiator and O-ethyl S-(phthalimidylmethyl) xanthate as the CTA. The resulting PNVP macro-CTA was further applied for the polymerization of the vinyl ester in dioxane solution at 80 °C using, again, AIBN as the initiator. The block copolymers were characterized through size-exclusion chromatography (SEC) and NMR spectroscopy. The thermal behavior of the copolymers was studied by Differential Scanning Calorimetry (DSC), whereas their thermal stability via Thermogravimetric Analysis (TGA) and Differential Thermogravimetry (DTG). [ABSTRACT FROM AUTHOR]

Aging of polymers is a natural process that occurs during their usage and storage. Predicting the lifetime of polymers is a crucial aspect that should be considered at the design stage. In this paper, a series of bio-based thermoplastic poly(ether-urethane) elastomers (bio-TPUs) with modified hard segments were synthesized and investigated to understand the structural and property changes triggered by accelerated aging. The bio-TPUs were synthesized at an equimolar ratio of reagents using the prepolymer method with the use of bio-based poly(trimethylene ether) glycol, bio-based 1,3-propanediol, and hexamethylene diisocyanate or hexamethylene diisocyanate/partially bio-based diisocyanate mixtures. The polymerization reaction was catalyzed by dibutyltin dilaurate (DBTDL). The structural and property changes after accelerated aging under thermal and hydrothermal conditions were determined using Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and dynamic mechanical thermal analysis (DMTA). Among other findings, it was observed that both the reference and aged bio-TPUs decomposed in two main stages and exhibited thermal stability up to approximately 300 °C. Based on the research conducted, it was found that accelerated aging impacts the supramolecular structure of TPUs. [ABSTRACT FROM AUTHOR]

Copyright of Polimery is the property of Industrial Chemistry Research Institute and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

This experimental study is devoted to the analysis of Multiwall Carbon Nanotubes (MWCNTs) and graphitic carbon nitride (g-C3N4) nanofiller reinforced epoxy hybrid nanocomposites using casting technique. Different weight fraction of nanofiller such as 0.5, 1, 3, and 5% were developed. Scanning Electron Microscope (SEM) and Transmission Electron Microscope (TEM) were used to confirm the morphological behaviors of developed hybrid nanocomposites and the agglomeration free uniform dispersion of nanofillers in epoxy matrix. The effects of reinforcements on the tensile, flexural, and water absorption properties of epoxy hybrid nanocomposites were also investigated. The results were tabulated and recorded. It was observed that the increase in reinforcement is found to be increased the behaviors of epoxy hybrid nanocomposites. [ABSTRACT FROM AUTHOR]

NdBa1 –xMgxFeCo0.5Cu0.5O5 + δ (0.00 ≤ x ≤ 0.40) double perovskites are synthesized by the ceramic method and their structure, oxygen nonstoichiometry (δ), and thermal and electrical transport properties are studied. NdBa1 –xMgxFeCo0.5Cu0.5O5 + δ compounds have a tetragonal structure (space group P4/mmm) and are semiconductors of the p-type, whose electrical conductivity characteristics at elevated temperatures changes to metal-like characteristics due to the release of oxygen from the samples (δ). The partial replacement of barium with magnesium in NdBaFeCo0.5Cu0.5O5 + δ leads to a decrease in the oxygen content (δ) in the solid solutions formed in this case, an increase in the size of their unit cell and the thermo-EMF coefficient, and a decrease in the thermal stability, linear thermal expansion coefficient, and electrical conductivity. The values of electrical transport energy, weighted mobility, and concentration of charge carriers in the studied materials are calculated. [ABSTRACT FROM AUTHOR]

Polyhedral oligomeric silsesquioxane POSS nanoparticles can be applied as reinforcing additives modifying various properties of biodegradable polymers. The effects of aminopropylisobutyl POSS (amine-POSS), trisilanolisooctyl-POSS (HO-POSS) and glycidyl-POSS (Gly-POSS) on the viscoelastic, thermal properties and crystallization of biodegradable poly(ε-caprolactone) PCL were studied. The analysis of the viscoelastic properties at ambient temperature indicated that aminopropylisobutyl POSS (amine-POSS) and glycidyl-POSS (Gly-POSS) enhanced the dynamic mechanical properties of PCL. The increase in the storage shear modulus G′ and loss modulus G″ was observed. The plasticizing effect of trisilanolisooctyl POSS (HO-POSS) due to the presence of long isoctyl groups was confirmed. As a result, the crystallization of PCL was facilitated and the degree of crystallinity of χc increased up to 50.9%. The damping properties and the values of tan δ for PCL/HO-POSS composition increased from 0.052 to 0.069. The TGA results point out the worsening of the PCL thermal stability, with lower values of T0.5%, T1% and T3%. Both HO-POSS and Gly-POSS facilitated the relaxation of molten PCL. The presence of Gly-POSS influenced the changes that occurred in the viscoelastic properties of the molten PCL due to the thermo-mechanical degradation of the material; a positive impact was observed. [ABSTRACT FROM AUTHOR]

Despite a recent sustained preoccupation for developing biobased epoxies with enhanced applicability, such products have not been widely accepted for industry because of their inferior characteristics compared to classic petroleum-based epoxy thermosets. Therefore, significant effort is being made to improve the flame retardance of the most commonly used epoxies, such as diglycidyl ether-based bisphenol A (DGEBA), bisphenol F (DGEBF), novalac epoxy, and others, while continuously avoiding the use of hazardous halogen-containing flame retardants. Herein, a phosphorus-containing bisphenol, bis(4-(((4-hydroxyphenyl)amino)(6-oxido-6H-dibenzo[c,e][1,2]oxaphosphinin-6-yl)methyl)phenyl) phenylphosphonate (BPH), was synthesized by reacting bis(4-formylphenyl)phenylphosphonate with 4-hydroxybenzaldehyde followed by the addition of 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO) to the resulting azomethine groups. Environmentally friendly epoxy-based polymer thermosets were prepared by using epoxy resin as polymer matrix and a mixture of BPH and 4,4′-diaminodiphenylsulfone (DDS) as hardeners. A hyperbranched phthalocyanine polymer (HPc) and BaTiO3 nanoparticles were incorporated into epoxy resin to improve the characteristics of the final products. The structure and morphology of epoxy thermosets were evaluated by infrared spectroscopy and scanning electron microscopy (SEM), while the flammability characteristics were evaluated by microscale combustion calorimetry. Thermal properties were determined by thermogravimetric analysis and differential scanning calorimetry. The surface morphology of the char residues obtained by pyrolysis was studied by SEM analysis. [ABSTRACT FROM AUTHOR]

The reputation of nanofluids as a convenient heat transfer media has grown in recent years. The synthesis of nanofluids is often challenging, particularly carbon-based nanofluids, due to the rapid agglomeration of the nanoparticles and the instability of the nanofluids. In this regard, surface modification and surfactant addition are potential approaches to improve the physical and thermal properties of carbon-based nanofluids that have been studied and the structural, morphological, and thermal characteristics of surface-oxidised carbon nanofibre (CNF)-based nanofluids has been characterised. Commercial CNF was first subjected to three different acid treatments to introduce surface oxygen functional groups on the CNF surface. Following the physical and thermal characterisation of the three surface-oxidised CNFs (CNF-MA, CNF-MB, and CNF-MC), including Raman spectroscopy, Fourier transform infrared (FTIR), thermogravimetric analysis (TGA), and field emission scanning electron microscopy (FESEM), the CNF-MB was selected as the best method to synthesise the surface-oxidised CNF-based nanofluid. A total of 40 mL of ultrapure water was used as a pure base fluid and mixed with the surface-oxidised CNF at a concentration range of 0.1–1.0 wt.%, with a fixed of 10 wt.% amount of polyvinylpyrrolidone (PVP). The thermal conductivity of CNF-based nanofluid was then characterised at different temperatures (6, 25, and 40 °C). Based on the results, surface oxidation via Method B significantly affected the extent of surface defects and effectively enhanced the group functionality on the CNF surface. Aside from the partially defective and rough surface of CNF-MB surfaces from the FESEM analysis, the presence of surface oxygen functional groups on the CNF wall was confirmed via the Raman analysis, TGA curve, and FTIR analysis. The visual sedimentation observation also showed that the surface-oxidised CNF particles remained dispersed in the nanofluid due to the weakened van der Waals interaction. The dispersion of CNF particles was improved by the presence of PVP, which further stabilised the CNF-based nanofluids. Ultimately, the thermal conductivity of the surface-oxidised CNF-based nanofluid with PVP was significantly improved with the highest enhancement percentage of 18.50, 16.84, and 19.83% at 6, 25, and 40 °C, respectively, at an optimum CNF concentration of 0.7 wt.%. [ABSTRACT FROM AUTHOR]

Despite the large demand, the current biomass composites still exhibit problems of low mechanical properties, strong hydrophilicity, and poor thermal resistance, which limit biomass composites' application fields. Facing these problems, starch-based fiber-reinforced composites with foam structures were fabricated by hot pressing and foaming process, for the first time. In these composites, the corn starch serves as matrix while the sisal fiber acts as skeleton. Aluminum hydroxide (ATH) has been added to alter microstructures. To identify microstructure and material composition changes induced by ATH, scanning electron microscopy, X-ray diffraction analysis, and Fourier transform infrared spectroscopy have been performed. Experimental results show that an appropriate ATH content can improve composite's ultimate tensile strength by as much as 37%. Molecular dynamic simulations were performed to understand ATH effects on tensile properties at an atomic level. In addition to tensile properties, the addition of ATH is also beneficial to improve the compressive properties, water resistance and thermal stability of starch-based fiber-reinforced composites, making the composite a potential candidate to replace traditional packaging materials. Therefore, this investigation will benefit the current packaging industry in that sustainable utilization of packaging materials can be realized.

This study explores the impact of non-stoichiometric aluminum oxide (AlxOy) coatings applied via thermal atomic layer deposition (ALD) on carbon fiber fabrics (CFFs), emphasizing volume per cycle, FESEM analyses, color transitions, and thermal stability enhancements. Using trimethylaluminum and water at 100 °C, AlxOy was deposited across a range of 1000 to 5000 ALD cycles, with film thicknesses extending up to 500 nm. This notable increase in the volume of material deposited per cycle was observed for the 3D CFFs, highlighting ALD's capability to coat complex structures effectively. FESEM analyses revealed the morphological evolution of CFF surfaces post-coating, showing a transition from individual grains to a dense, continuous layer as ALD cycles increased. This morphological transformation led to significant color shifts from green to red to blue, attributed to structural coloration effects arising from variations in film thickness and surface morphology. Thermogravimetric analyses (TGA and dTG) indicated that the AlxOy coatings enhanced the thermal stability of CFFs, with a postponement in degradation onset observed in samples subjected to more ALD cycles. In essence, this research highlights the nuanced relationship between ALD processing parameters and their collective influence on both the aesthetic and functional properties of CFFs. This study illustrates ALD's potential in customizing CFFs for applications requiring specific color and thermal resilience, balancing the discussion between the surface morphological changes and their implications for color and thermal behavior. [ABSTRACT FROM AUTHOR]

The environmental threats posed by manmade composites during their disposal and depletion of fossil fuel resources have necessitated the application of ecofriendly materials for composite making. In the recent decades, many plant fibers with promising potentials required for reinforcing composites have been identified and used for various applications. In this paper, physical, mechanical, and thermal properties in addition to chemical composition of novel lignocellulosic fiber extracted from the bark of Albizia saman (AS) have been reported. Chemical tests on ASFs revealed the presence of high cellulose and lignin contents (60.76% and 14.64%), which contributes significantly to the strength and rigidity of the AS fiber. FT-IR and X-ray diffraction study confirmed the presence of cellulose with high degree of crystallinity (57.69%) and crystallite size (2.85 nm). Thermal stability of ASFs studied through Thermogravimetric, Derivative Thermogravimetric, and Differential Scanning Calorimetry curves revealed the maximum degradation of ASFs as 306.19°C with kinetic activation energy (KAE) of 64.01 kJ/mol. The tensile strength and tensile strain of ASFs was found to be to be in the range 381–1092 MPa and 1.65–4.42%, respectively, and the value of tensile modulus was found to be 9.68–42.31 GPa. From the results, it can be concluded that ASFs possess the essential characteristics required for reinforcing composites and hence can be suitably used for making green composites.

We present the deposition and characterization of tungsten-tantalum diboride (W,Ta)B2 coatings prepared by the high-power impulse magnetron sputtering technique. We evaluated the influence of pulse duration and substrate bias on the properties of (W,Ta)B2 films. A high hardness of up to 35 GPa measured by nanoindentation was simultaneously obtained with good elastic properties. Changing the pulse duration greatly affected the B/(W+Ta) atomic ratio, which influenced the properties of the coatings. The deposited films are thermally stable at up to 1000 °C in vacuum and are able to withstand oxidation at 500 °C. [ABSTRACT FROM AUTHOR]

The use of biowaste materials as additives in polymeric matrices has generated interest. Garlic is a seed that has wide application areas, not only in the food industry, because it has good bactericidal and antioxidant properties. Polypropylene (PP) is a commodity polymer that has a wide range of applications, including containers, construction materials, automotive parts, domestic issues, etc. In the present work, the obtaining of composite materials based on a Polypropylene with a medium melt flow index as a matrix and as a reinforcing agent garlic husk particles (GHP). The addition of GHP in different contents was evaluated (2 to 10 PHR), and the composites were characterized by thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA) and X-ray diffraction (×RD). According to the results, the thermal stability of PP-GHP decreases with the GHP, in addition to the results of DSC and XRD, that showed that the crystallinity of PP-GHP composites was higher compared to the pristine PP. DMA results allow us to identify that the addition of GHP generates a reinforcing effect on PP matrix, which means that this waste material can be considered a bioadditive with positive effects on polymeric matrices. [ABSTRACT FROM AUTHOR]

The global demand for plastics has been continuously increasing at a rapid rate and their disposal largely pollutes the atmosphere and oceans. Natural fibers possess the inherent characteristics required for plastic making and their disposal causes less harm to the environment. In this paper, physicochemical, thermal, mechanical and morphological characteristics of novel cellulosic fiber extracted from the bark of Tithonia diversifolia (TD) investigated through various characterization tests have been reported. TDFs were found to possess higher cellulose (63.9 wt.%) and high lignin content (19.3 wt.%) which make them stronger and more stable. Lower density (1440 kg/m³), higher crystallinity index (51.84%), higher tensile strength (243–386 MPa) and higher thermal stability (up to 337.17°C) make TDFs more suitable for making green composites. The morphology of the TD fiber surface observed through field emission scanning electron microscopy (FESEM) was found to be rougher with some serrations which facilitate better bonding characteristics with the polymer matrix. [ABSTRACT FROM AUTHOR]

The glass composition (70-x)PbO-(30-y)B2O3-(x+y)AlF3, where x and y ranges from 0 to 20 mol%, were prepared using the conventional melt-quenching-annealing technique. The structural and thermal properties of the glasses were comprehensively analyzed using techniques like Differential Thermal Analysis (DTA), Dilatometry, Fourier-Transform Infrared Spectroscopy (FTIR), X-ray Diffraction (XRD), and Scanning Electron Microscopy (SEM). XRD confirmed the amorphous, non-crystalline structure of the glasses. The glass network was found to be composed of structural units such as PbO4, BO4, BO3 and AlO6 using FTIR spectroscopy. FTIR analysis revealed significant structural changes, including the transformation of BO4 to BO3 units and the increase in non-bridging bonds, particularly with higher AlF3 content. DTA was instrumental in determining characteristic temperatures, such as the glass transition, melting, and peak crystallization temperatures, along with glass stability parameters (ΔT, Hr, Tgr) for all samples. The study found that the addition of AlF3 led to a decrease in these characteristic temperatures when replacing B2O3, but an increase when replacing PbO. Variations in the density and thermal expansion of the lead borate glass were observed upon the addition of AlF3, decreasing when substituting for PbO and increasing when substituting for B2O3. These findings provide insights into the properties of oxyfluoride glasses, paving the way for future optimization in their composition for varied applications. [ABSTRACT FROM AUTHOR]

Agglomeration is a technological process that is widely applied to obtain powdered products with the appropriate shape and particle size and different physical characteristics and stabilities. The purpose of this research was to study the influences of the composition and storage of powdered infant formulas on their thermal behaviours, as analysed by differential scanning calorimetry (DSC); fatty acid compositions, as determined by gas chromatography; and water activity and water content. This study investigated the influence of the storage time (six months) at temperatures of 20–22 °C and air humidities of 42–45% on powder mixtures and agglomerates. The isotherms of the agglomerates presented a shape and course similar to those of the isotherms of the mixtures from which they were obtained. The agglomeration process affected the stability of the fatty acids in the stored powdered infant formulas. The composition of the fatty acids changed during the storage process. The thermal properties of the powdered infant formulas were not significantly influenced by agglomeration. The compositions of the mixtures and agglomerates influenced the shape and course of the DSC diagrams. Using the DSC method, it was determined whether the fat was a natural component of the powder or it was added in the form of fatty acid preparations. Differences were observed between the shape and course of the DSC curves (heating and cooling) obtained for fresh and 6-month-stored mixtures and agglomerates. [ABSTRACT FROM AUTHOR]

Washingtonia is a palm tree that enriched with lignocellulosic biomass, which provided it with the potentiality for various applications. In this study, different biomass from Washingtonia plant, i.e. leaf stalk (W-LS), trunk core (W-TC), and trunk spine (W-TS) fibers, were collectively investigated by characterization. Under scanning electron microscopy (SEM) examination, the spine-shape structure of W-TS fiber along with its small particle size might facilitate it for fabrication reactivity. From chemical and elemental composition analysis, both W-TC and W-TS fibers were found with high cellulose content, while with the closely similar residual elements, suggesting them from the same source of trunk segment. However, the low cellulose content of W-LS fiber with its high ash content had somehow reduced its crystallinity and thermal stability properties. From X-ray diffraction (XRD) analysis, the crystallinity was estimated the highest for W-TS (68.2%), and while with the lowest for W-LS fiber (57.3%), which in line with the detected functional groups by Fourier Transform Infrared-ray (FTIR) spectrophotometry. In thermogravimetry (TGA) analysis, all fibers possessed great thermal resistance with Tonset in the range of 307.4–328.1°C and Tpeak in the range of 352.4–347.9°C. Washingtonia fiber had a high potential to be applied as a bio-material for versatile applications in the future.

In this paper, the surface of baobab pod fibers (BPFs) is treated using sodium hydroxide (NaOH) at various (0 min to 100 min at step size of 20 min) soaking time. The samples are labeled A, B, C, D, E and F. The effect of mercerization on the fibers is investigated via structural, morphological, mechanical, chemical and thermal analyses. The structural test reveals that sample E (80 min treated fiber) is the optimized BPF with percentage of crystallinity (%Cr) of 70.07%. The morphological test also indicates that sample E (80 min treated fiber) is the optimized fiber due to its roughened surface. Also, the chemical spectra show the presence of Na in the treated fibers and the intensity of Na increases as the soaking time increases. The maximum tensile stress and Young’s modulus of optimized BPF are 390 MPa and 5.94 GPa, respectively for sample E from mechanical analysis. The initial transition temperature range is from 231 to 248 ℃ and the final transition temperature range of 323 to 398 ℃ is obtained from thermal stability analysis. The thermal stability measurements indicate that treatment of BPFs for 80 min is the optimized duration and enhances the thermal stability of the BPFs.

L‐ and D‐ form oligo(lactic acid)s (OLLA and ODLA) grafted α‐cellulose (OLLA‐g‐cellulose and ODLA‐g‐cellulose) were prepared by the graft polycondensation reaction in C6H5CH3 medium at 130°C and 380 mm of mercury pressure. Para‐toluene sulphonic acid (5 wt% of oligo(lactic acid)) was used as a catalyst whereas potassium persulfate (0.01 wt% of oligo(lactic acid)) was used as a co‐catalyst in the graft polycondensation reaction. OLLA and ODLA with a degree of polymerization (DP) 6–7 used in polycondensation reaction were also prepared by ring‐opening polymerization of L‐ and D‐lactides at 140°C for 10 h with stannous octoate (C16H30O4Sn) as a motivator, L, and D monomer of lactic acids as co‐motivators. FTIR analysis proved the bonding of OLLA and ODLA onto the α‐cellulose surface. The thermal properties of poly(L‐lactic) acid (PLLA) composites were explored by thermal analysis (TG, DTA, and DTG). Degradation, melting, and maximum weight loss temperature of the composites were increased with the increase of grafted cellulose up to 10% and then decreased. TG and DTA results showed that the incorporation of grafted α‐cellulose (grafted cellulose) can improve the thermal properties of PLLA composites. Highlights: Synthesis of oligo(lactic acid)s from L‐ and D‐lactides by ring‐opening polymerization reactions.α‐cellulose extraction and graft modification with oligo(lactic acid)s.Preparation of grafted α‐cellulose composite with PLLA matrix.Evaluation of thermal properties of the grafted α‐cellulose‐reinforced composites. [ABSTRACT FROM AUTHOR]

This research explores the custom-made design of nanomaterial designs to improve the mechanical and thermal properties of polypropylene (PP) framework nanocomposites. Functionalized multiwalled carbon nanotubes (f-MWCNTs) and polyvinylpyrrolidone-modified nano-silica (PVP-SiO2) were deliberately consolidated into the PP matrix, illustrating improved scattering and interaction at the atomic level. Morphological examination uncovered a uniform dissemination of nanofillers, driving to upgrade mechanical properties. Tensile tests illustrated a dynamic increment in Young’s Modulus and Tensile Strength with higher concentrations of nanofillers, especially in definitions NC3 and NC4. Thermal analysis, counting differential checking calorimetry (DSC) and thermogravimetric analysis (TGA), demonstrated hoisted glass move temperatures and upgraded warm solidness. Comparative execution with related works highlighted the special commitments of this ponder, emphasizing green activities, sustainability, and progressions in multifunctionality. The nanocomposites display promising results, with NC3 appearing with a Young’s Modulus of 2.5 GPa and Tensile Strength of 35 MPa, whereas NC4 accomplished a Young’s Modulus of 3.0 GPa and Tensile Quality of 40 MPa. These discoveries emphasize the potential of tailored nanomaterial models for creating high-performance and environmentally capable polymer network nanocomposites.

Polymer nanocomposites have been of great interest to packaging, energy, molding, and transportation industries due to several favorable properties including a higher resistance to stress and cracking even under flexed conditions, and also a chemical resistance to water, acids, and alkalis. The current work disseminates the studies on the mechanical and thermal properties of the polypropylene HHR102 polymer reinforced with nano dispersoids of silicon dioxide at varied weight fractions. The nanocomposites, fabricated via melt processing followed by injection molding, were tested for tensile strength, % elongation, tensile modulus, and impact toughness. Further, the samples were also subjected to dynamic mechanical analysis (DMA) and thermogravimetric analysis (TGA) to determine the dynamic storage modulus and thermal stability. The addition of nano-silica in polypropylene HHR102 resulted in enhanced ductility and well-balanced tensile modulus; however, the tensile strength and impact toughness were found to be decreased. On the other hand, the storage modulus was significantly increased for all nano-silica (NS)-containing polypropylene HHR102 matrices. With the increased nano-silica content, the storage modulus was optimal. Further, with the lower weight loss of 30% and 50%, the thermal stability of the increased silica content PP nanocomposites was much affected. However, it improved at a weight loss of 30% for the lower silica content PP nanocomposite (PP-1%NS). The imbibition was found to increase with the increase in NS. The increase in imbibition is attributed to the micro-voids generated during ageing. These micro-voids act as channels for water absorption. Further, the degree of crystallinity of the nanocomposites was decreased as a result of inhibition by the nano-particles on the regular packing of polymer molecules. The structure–property correlations were explicated based on the achieved mechanical properties.

The alarming increase in the global pollution levels has necessitated the use of eco-friendly materials in composite making. Natural fibers derived from plant sources possess superior mechanical properties and proves to be a suitable alternate for synthetic fibers. In this paper, an attempt has been made to study the physico-chemical, mechanical, thermal, and morphological properties of new cellulosic fiber obtained from the bark of Bauhinia purpurea through various tests such as chemical, tensile, Fourier Transform Infrared Spectroscopy (FT-IR), X-ray diffraction (XRD), thermogravimetric (TG), differential scanning calorimetry (DSC), and field emission scanning electron microscopy (FESEM). From test results, Bauhinia purpurea fiber (BPF) was found to possess high cellulose (67.46 wt.%), with high crystallinity index (65.61%), and was found to offer high tensile strength (375.77 − 793.25 MPa) and large Young’s modulus (12.78–20.12 GPa). Lower density (1190 kg/m3) and high onset temperature of thermal degradation (225.55°C) make BPF more appropriate for making biodegradable composites for automobile and infrastructure sectors.