Search

Lithium‐ion cell chemistries are favored in the automotive sector, as they enable electric vehicles (EVs) to compete with traditional gasoline‐powered vehicles in terms of performance, range, and cost. The life and performance of these packs depend upon the Battery management system which monitors and controls the pack. The modeling, simulation, and analysis of a lithium‐ion battery pack that closely resembles an actual automobile battery are the focus of this paper. Real cells that are commercially available and specifically developed for automotive applications are modeled in the simulation environment. The cell characterization and formation of pack topology with heat exchange are addressed. A commercial electric car's power train model and EV dynamics are used in the simulation environment to test the modeled battery pack over various drive cycles. The performance analysis is upscaled by considering different aspects like resistive forces while driving, ambient temperature, initial conditions while the vehicle starts, etc. The battery manufacturer can verify the battery's performance under different load conditions, with a high degree of similarity to real‐world scenarios. The simulations are conducted on MATLAB/Simulink 2021b software. [ABSTRACT FROM AUTHOR]

In this paper, the temperature response of a lithium‐ion type 18650 battery pack cooled by a thermoelectric air‐cooling module is presented. The effects of the airflow rate, on‐off cooling fan position, charging and discharging rate and cooling by the thermoelectric air‐cooling module are investigated. The charging and discharging procedures with different current rates of 2 A (0.06 C), 3 A (0.09 C), and 4 A (0.12 C) are investigated. The results showed that different test conditions of the thermoelectric air‐cooling module have a substantial effect on the temperature of the battery pack. It was demonstrated that a thermoelectric air‐cooling module has a decreased battery temperature of lower than 40°C. The operating conditions of the cooling fans have a substantial effect on battery temperature. The experiment in which all the cooling fans are turned on shows a higher cooling capacity than natural air cooling by approximately 16%–57%. However, when setting the on‐off position of the fans that are installed in different positions, the cooling capacity when the fans at the inlet and thermoelectric cooling heat sink are turned on and the fan at the outlet battery pack is turned off is slightly less than that when all the cooling fans are turned on by approximately 25%–57%. Therefore, it can be selected as an optimum for cooling the battery pack due to less power consumption and noise issues. The proposed research can be implemented as a guideline for the cooling system of energy storage, such as small electric vehicle platforms, ground batteries, and solar energy storage. [ABSTRACT FROM AUTHOR]

Academic research in the battery field frequently remains limited to small coin or pouch cells, especially for new materials that are still rather far from commercialization, which renders a meaningful evaluation at an early stage of development challenging. Here, the realization of large lab‐scale pouch cells comprising Sn0.9Mn0.1O2 (SMO), prepared via an easily scalable hydrothermal synthesis method, as an alternative active material for the negative electrode and LiNi0.6Mn0.2Co0.2O2 (NMC622) as a commercially available active material for the positive electrode is reported. Nine double‐layer pouch cells are connected in series and parallel, suitable for powering a remote‐controlled vehicle. Subsequently, these SMO‖NMC622 cells are critically evaluated by means of an early‐stage life cycle assessment and compared to graphite‖NMC622 cells, in order to get first insights into the potential advantages and challenges of such lithium‐ion chemistry. [ABSTRACT FROM AUTHOR]

The application of lithium‐ion batteries especially for electric vehicles has been limited by the factors of safety, lifetime, charging time, and cost. One of the principal limitations is that the performance of Li‐ion batteries drops intensely in a cold environment. Cold environment dramatically reduces the available capacity of the batteries and increases its internal impedance at the same time. Therefore, the estimation of state‐of‐health is of great importance in battery performance evaluation and lifetime prediction. Furthermore, the heating methods need to be developed to ensure that batteries work in abnormal temperature conditions. This paper conducts a comprehensive review specifically on the poor performance of lithium‐ion cells under severe conditions. The content contains three sections. First, a comprehensive study on the aging mechanisms of lithium‐ion batteries at cold temperatures is undertaken. Second, the estimation methods of the health state of the batteries are conducted, which is vital to understand the fundamentals and quantify the performance and aging effects for lithium‐ion batteries. Third, the heating methods are classified and studied in detail to reduce the degradation mechanism and promote the performance of lithium‐ion batteries under sub‐zero conditions. [ABSTRACT FROM AUTHOR]

A battery pack is the main energy storage element, and directly affects the performance of an electric vehicle. Battery thermal management system research and its development for a modern electric vehicle is required. This paper selects the forced air cooling of battery pack as the research object, and uses simulation methods to research the heat dissipation performance with different structures of battery packs. The results indicate that according to the four types of transient state conditions, the rising temperature of both battery packs are significantly higher than the temperature difference, the maximum temperature rise and temperature difference of a horizontal battery pack are lower than a longitudinal battery pack. When an electric vehicle begins to decrease speed, the curves of temperature rising and temperature difference increase. This shows the internal heat is continuously rising, so even in a electric vehicle beginning to decrease speed, the fan must work. The reference basis for choosing battery pack type and an analysis of heat flow field characteristics, including fan run-time control, are offered. [ABSTRACT FROM AUTHOR]