Search

In this study, composite was made by the addition of 10 wt% SiC particles in the LM25 matrix through gravity casting and thixocasting processes. Thixocasting temperature was varied to investigate its effect on the microstructure, mechanical and thermal properties. Properties of thixocast samples were also compared with gravity cast ones. XRD analysis was done to analyse the phases present in the samples. Optical microscope and scanning electron microscope were used to record the microstructures of gravity cast as well as thixocast samples. Tensile, compressive and flexural tests were performed on universal testing machine with the prepared composite samples according to the ASTM standards. Thermal diffusivity tests of gravity cast and thixocast samples were done on laser flash diffusivity instrument. Results reveal that thixocast samples are sounder than the gravity cast samples. The microstructure of α-Al phase transformed from dendritic to globular shape due to the thixocasting. Also, volume fraction of eutectic phase in the sample increased with the increment of thixocast temperature. Tensile strength, compressive strength and flexural strength were found higher in the case of thixocast samples as compared to gravity cast. Thermal diffusivity considerably increased due to thixocasting, while its value slightly reduced with increment of thixocast temperature. [ABSTRACT FROM AUTHOR]

Laboratory tests were conducted to study the physical and mechanical properties of granite after heating and water-cooling treatment for 1 and 30 cycles from room temperature to 500 °C. The change mechanisms for the water-cooling treatment were analysed via scanning electron microscope observation. At 500 °C, the volume of granite increases by 1.73% and 2.55%, the mass decreases by 0.16% and 0.31%, and the density decreases by 1.86% and 2.78% after 1 and 30 thermal cycles, respectively. The average values of UCS and E after 1 and 30 cycles both decrease as the temperature rises, while the peak strain exhibits the reverse trend. A yield platform is observed in the yield stage of the stress–strain curve above 300 °C, and the ductility of granite gradually increases with temperature. The normalized P-wave is linear with respect to the normalized UCS and E at 1 thermal cycle, whereas it shows exponential relationships with the normalized UCS and E at 30 thermal cycles. The degradation of the physical and mechanical properties of granite after 1 and 30 cycles is mainly caused by the generation and development of microcracks inside the rock. Compared to 1 thermal cycle, more microcracks are observed at 30 thermal cycles. Therefore, the thermal cyclic treatment can further deteriorate and weaken the physical and mechanical properties of granite. [ABSTRACT FROM AUTHOR]

In this study, the influence of nanosilica (SiO2 NPs) on the mechanical, thermal and barrier properties of poly(butylene adipate-co-terephthalate) (PBAT) nanocomposites was investigated. The PBAT/SiO2 composites were prepared by solution blending technique. PBAT/SiO2 composites were prepared with different percentages of nano-SiO2 loading (1, 3, 5, 7 and 10 wt%). The relations of SiO2 NPs with PBAT matrix were analyzed by Fourier transform infrared spectroscopy. The mechanical properties such as tensile strength, % of elongation at break, tensile modulus and thickness were determined. The thermal properties such as thermo-gravimetric analysis were analyzed for the nanocomposites. The PBAT/SiO2 composites exhibit high mechanical and thermal performance than the pure PBAT. The nanocomposites were also investigated through scanning electron microscope (SEM) and transmission electron microscope micrographs to examine the morphology between PBAT and SiO2 NPs. In addition, the results of SEM acquired are in SiO2 agreement with the data resulting from FTIR and tensile strength of the nanocomposites. The nanocomposite shows improvement in mechanical and thermal stability than that of pure PBAT. [ABSTRACT FROM AUTHOR]

Blends of cis-polyisoprene (CPI) and nitrile butadiene rubber (NBR) in different volume ratio were prepared to see the effect of composition on different properties. Structure characterization has been done through X-ray diffraction and scanning electron microscope. Scanning electron micrographs confirm homogeneous nature of all the blends. The dynamic mechanical analyzer was used to measure damping, storage modulus, glass transition temperature and mechanical properties (Young's modulus and tensile strength) of these blends. Activation energy and fragility were determined for the non-Arrhenius (fragile) behavior of viscosity using Vogel-Fulchuer-Tammann (VFT) equation. Thermal conductivity has been analyzed through thermal constant analyzer. Results indicate that all the measured properties are dependent on blend composition and crosslink density. [ABSTRACT FROM AUTHOR]

The poly(styrene-b-butadiene-b-styrene) (SBS) triblock copolymer and linear low-density polyethylene (LLDPE) were blended and irradiated by γ rays to prepare shape memory polymer (SMP). Different weight fractions of conductive carbon black (CB) were filled into SMP to form a novel electroactive shape memory CB/SBS/LLDPE composite. The CB reinforced radiation cross-linked SBS/LLDPE blends for the improvement of the mechanical weakness and conductivity of SBS/LLDPE bulk and for wide practical engineering uses. The electroactive shape memory CB/SBS/LLDPE composites were investigated by electrical properties, mechanical, dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), scanning electron microscopy (SEM), and electroactive shape memory effects. It is found that the tensile strength, storage modulus, and resistance against mechanical and thermal mechanical cycle loading in the developed composites increased due to the role of reinforcement of CB. The melting temperatures and volume resistance of the composites decreased with the increment of CB for excellent electrical conductivity of CB. The electroactive shape memory effects of developed CB/SBS/LLDPE composites were affected by CB weight fractions and applied voltage, while good shape recovery could be obtained in the shape recovery test. When the CB fraction is more than 5 wt%, full recovery can be observed after tens of seconds and shape recovery speed increased with CB fractions and voltage increasing. However, the shape recovery rate decreases slightly with increment of cycle times. [ABSTRACT FROM AUTHOR]

Cyanogen functionalized carbon nanotube and graphene/poly (arylene ether nitrile) (CNT-CN/GN-CN/PEN) nanocomposite films were prepared by a facile solution casting method. The weight ratio of CNT-CN/GN-CN was varied from CNT-dominated to GN-dominated for the purpose of investigating their synergetic effects on the mechanical and thermal properties of PEN nanocomposites. Consequently, GN-CN/PEN composites demonstrated better mechanical and thermal properties than CNT-CN/PEN composites due to larger contact area between GN-CN and PEN matrix. Nevertheless, all CNT-CN/GN-CN/PEN composites exhibit enhanced mechanical properties than those of GN-only nanocomposites. With the increasing of CNT-CN/GN-CN weight ratio, the mechanical properties of CNT-CN/GN-CN/PEN composites increase, then decrease, and reach their maximums when CNT-CN/GN-CN weight ratio is around 4/4. From scanning electron microscope images, it is found that around that point GN-CN is flatly dispersed and CNT-CN is penetrated into GN-CN, capable of transferring stress load and thus decreasing interface loss. Thermal properties of CNT-CN/GN-CN/PEN composites once again confirmed the joint effect of CNT-CN and GN-CN, leading to improved thermal properties. In short, a synergistic effect between one-dimensional (1-D) CNT and two-dimensional (2-D) GN on the mechanical and thermal properties of nanocomposites have been demonstrated in these systems. [ABSTRACT FROM AUTHOR]