Search

In electrical discharge machining (EDM), it is a much more effective method to improve working characteristics by changing the input process of pulse energy. However, it has not been investigated enough whether pulse form is the most adequate or not. In this study, the effect of superimposed pulse current waveform and its parameter on surface integrity was investigated. The surface topography, roughness, microstructure, white layer thickness, and residual stress were analyzed and discussed. Moreover, the material removal rate was also tested and compared. The results show that with the backward movement of the superimposed pulse current, the material removal rate and surface roughness decrease, while the white layer thickness, residual stress, and surface defects increase. The current waveform has little influence on microstructure. Under the same pulse discharge energy and pulse-on time, the samples processed by superimposed pulse current waveform instead of rectangular current waveform can obtain a thinner white layer, lower residual stress, fewer surface defects, and high surface roughness. With the increase of superimposed pulse-on time and current, the surface integrity becomes worse due to the increase of pulse energy. This paper provides a guide to the development and selection of EDM discharge current waveforms in EDM. [ABSTRACT FROM AUTHOR]

Micro electrical discharge drilling (ED-drilling) is a machining method used to make micro holes in hard-to-cut materials. The RC-discharge generator is often used because it creates a short and strong discharge spark. However, this method has issues such as current oscillation between tool electrode and workpiece, causing polarity changes that increase tool wear, and a low material removal rate due to long spark delay time. Furthermore, micro ED-drilling results in a large taper angle due to second discharge sparks created by debris in the narrow gap. To address these issues, the effect of adding graphite powder to the working fluid was studied. The graphite powder in kerosene created a bridge effect that reduced tool wear and taper angle, while improving MRR and surface roughness. The electrical conditions were not changed, and the machining process was improved by only altering the working fluid without modifying the existing system. [ABSTRACT FROM AUTHOR]

Recent developments in material science have concentrated not only on the improvement in mechanical properties, but also on the machinability that was difficult for system profiles. The present research explains the machinability assessment of the part of the sintered powder metallurgy using an electric discharge machining. The ferrous clay matrix preparations are constructed from iron–carbon–copper material and bentonite clay. The selected input parameters for the measurement of machinability are wt. % of clay, current (A), pulse on time (µs) and voltage (V), whereas the electrode wear rate, material removal rate and surface roughness (Ra) are considered as performance features. Results show that the performance parameters have been optimized at three different parametric conditions. Further, to obtain single optimum condition the hybrid GRA-TOPSOS methodology has been implemented for maximum MRR with minimum EWR and low surface roughness. The single optimum condition has been found at 5% clay, current 7 A, voltage 49 V and pulse on time 400 µs. The study of micro-structure and chemical composition of machined surfaces has been carried out using scanning electron microscopy with X-ray diffraction and energy-dispersive spectrometry analysis, respectively. The SEM exposes the less recast layer and micro-cracks during electrical discharge machining of ferrous clay composite. [ABSTRACT FROM AUTHOR]

The paper details a comprehensive experimental investigation on the influence of operating parameters and cut direction (parallel and perpendicular to fibre orientation) when wire electrical discharge machining (WEDM) unidirectional CFRP composites using zinc-coated brass wire (0.25-mm diameter). A Taguchi L18 fractional factorial orthogonal array considering four variable parameters including open voltage, ignition current and pulse-on time as well as pulse-off time was carried out for each cut direction. Results showed that a ~ 16% increase in maximum material removal rate was achieved when machining parallel to fibre direction (2.41 mm3/min) compared to cutting perpendicular to the fibres (~ 2.08 mm3/min), which was attributed to the higher electrical conductivity of the workpiece along the fibre length leading to greater discharge energies. This however resulted in relatively larger average kerf widths and poorer workpiece surface roughness (Sa) caused by the Joule heating effect. Workpieces machined parallel to fibre direction were generally free of any major edge defects, in contrast to severe delamination observed on both the top and bottom surfaces of specimens cut perpendicular to fibre orientation. High-magnification scanning electron microscopy of the machined surfaces revealed the presence of adhered resin material, fibre cracking, cavities/gaps in the matrix phase and interlayer cracks on most of the samples analysed, with damage severity dependent on the operating parameters and cut direction. [ABSTRACT FROM AUTHOR]

The modern industry which widely utilized sinking electrical discharge machining (EDM) with kerosene has many problems including low processing efficiency, unsafety, unfriendly environmental impact, and poor machined surface accompanying with recast layer. In this paper, a new water-in-oil (W/O) nanoemulsion dielectric is proposed to overcome these shortcomings of conventional sinking EDM. The machining performance and mechanism of sinking EDM using W/O nanoemulsion are investigated in both rough and finishing machining by comparing with kerosene. The main characteristic parameters for evaluating machining performance, including material removal rate (MRR) and relative electrode wear rate (REWR) in rough machining, and machined surface quality in finishing machining are studied. Compared with kerosene, using W/O nanoemulsion as a dielectric in sinking EDM, a nearly 34 times higher MRR and a relatively lower REWR are obtained in rough machining, and a better machined surface with no recast layer is attained in finishing machining. [ABSTRACT FROM AUTHOR]

In this paper, an inexpensive auxiliary tool vibration device is described that improves the efficiency of deep groove electrical discharge machining (EDM). Titanium alloy samples (Ti-6Al-4V) were machined using two different methods: unassisted normal EDM and vibration-assisted EDM, using copper, copper-tungsten, and graphite tool electrode materials. The vibration-assisted EDM machining was done at 40, 90, and 140 Hz, and the material removal rate, tool electrode wear rate, and surface roughness of the specimens were compared. Experimental results revealed that the material removal rate with vibration-assisted EDM was better than that obtained using unassisted EDM with copper and copper-tungsten electrodes. In this study, the vibration frequency was found to have an optimum value of 90 Hz with respect to surface roughness. It was found that the machining time for a groove 10 mm deep with vibration-assisted EDM was reduced by 200% compared to unassisted EDM. This new vibration device can help in the development of a more efficient deep groove EDM. [ABSTRACT FROM AUTHOR]

With the development of micro electro mechanical system (MEMS), the application of micro components is becoming increasingly wide. Micro electrical discharge machining (micro EDM) is one of the most effective manufacturing processes for micro components. During past few decades, some innovative methods for improving micro EDM performance have been proposed. Using special-shaped electrode is just one of them. Although micro EDM with helical electrode has been proposed and the availability has been proved for several years, relatively little is known about the precise effect of helical electrode rotation on micro EDM performance. In this study, micro through-holes were machined on Ti6Al4V sample with a cylindrical electrode and helical electrode. The helical electrode achieves better machining performance overall compared to the cylindrical electrode due to its favorable debris removal ability. The higher the rotational speed of helical electrode, the higher the material removal rate (MRR). When using the cylindrical electrode, the MRR first increases and then decreases after reaching a peak at 3000 rpm. Higher MRR is obtainable with the helical electrode with reverse rotation; with forward rotation, it yields higher machining precision (lower overcut and taper rate). [ABSTRACT FROM AUTHOR]

Limited efforts have been made to transform electrical discharge machining to a green and sustainable machining process. Current electric discharge machining (EDM) processes use hydrocarbon or synthetic-based dielectric fluids. These fluids emit harmful vapors when they break down, raising concerns for machine operators and for the environment. Biodiesel (BD) has similar properties as conventional dielectric and it can be used in place of conventional dielectric fluids. This research aims to study the effects of biodiesel dielectric in EDM process, especially in micromachining. Experiments are carried out in both low and high energy settings, on bulk metallic glass (BMG) and titanium alloy (Ti-6Al-4 V) using 200-μm-diameter electrodes. Canola BD and sunflower BD are compared against conventional dielectric in terms of material removal rate and tool wear ratio. The experimental evidence showed that both canola and sunflower BD are able to outperform conventional dielectric, and thus suggesting that BD has the potential to replace conventional dielectric as to provide a more sustainable machining process in the future. [ABSTRACT FROM AUTHOR]

Porous metals and alloys are ideal lightweight and damping materials which have garnered significant research attention owing to their superior mechanical and metallurgical characteristics. Micro electrical discharge machining (micro EDM) is an alternative method for machining porous metals. In this study, experiments on porous stainless steel (PSS) were conducted to determine the micro EDM performance of austenitic stainless steel (AISI 304) and PSS samples with various porosities and pore sizes. The results were analyzed based on the thermal conduction theory of porous materials. PSS achieved better machining performance overall compared to AISI 304 due to its porosity; further, porosity and pore size were shown to have a significant influence on the machining characteristics of PSS. The larger the porosity and pore size, the higher the material removal rate (MRR) and the lower the relative tool wear ratio (RTWR). Thermal conductivity decreases due to the existence of pores, causing less heat to be lost by heat conduction and more energy to be consumed in order to remove the material. High capacitance in the experimental circuit proved suitable for machining PSS, while high open circuit voltage appeared to be more suitable for machining AISI 304. [ABSTRACT FROM AUTHOR]

Electrical discharge machining is a very accurate non-traditional manufacturing process for creating tiny apertures, complex shapes and geometries within mechanical parts and assemblies. Its performance is evaluated in terms of surface roughness, existence of cracks, voids, and recast layer on the surface of product. The high heat generated on the electrically discharged material during the electrical discharge machining (EDM) process unfortunately decreases the quality of product. In this paper, the high strength and unique electrical and thermal properties of multi-wall carbon nanotubes are used to improve the EDM performance when machining the AISI H13 tool steel, by means of copper electrodes. Material removal rate, electrode wear rate, surface roughness, and recast layer were measured in presence of carbon nanotubes in the dielectric, then compared to the outcome of traditional EDM. Experiments show that mixing multi-wall carbon nanotubes within the dielectric makes the EDM more efficient, particularly if machining parameters are set at low pulse of energy. [ABSTRACT FROM AUTHOR]

This paper investigates an optimisation design of the various machining parameters for the electrical discharge machining (EDM) processes on AISI D2 tool steel using a hybrid optimisation method. A new combination of response surface methodology (RSM) and grey relational analysis coupled with principal component analysis (PCA) has been proposed to evaluate and estimate the effect of machining parameters on the responses. The major responses selected for this analysis are material removal rate, tool wear rate and radial overcut or gap, and the corresponding machining parameters considered for this study were pulse current ( Ip), pulse duration ( Ton), duty cycle ( Tau) and discharge voltage ( V). Thirty experiments were conducted on AISI D2 steel workpiece materials based on a face-centred central composite design. The experimental results obtained were used in grey relational analysis, and the weights of the responses were determined by the PCA and further evaluated using RSM. The results indicate that the grey relational grade (GRG) was significantly affected by the machining parameters considered and some of their interactions. The $R^2$ value for the GRG model was found to be 0.83, and the optimal parameter setting was determined for the grey relational grades. The analysis of variance results reveal that Tau is the most influencing parameter having 28.57 of percentage contribution followed by Ip, V and Ton with 11.52, 5.89 and 5.83 %, respectively. The interaction of the parameters contributes 31.19 % of percentage contribution. These results provide useful information on how to control the machining parameters and thereby responses and ensure high productivity and accuracy of the EDMed component. This method is simple with easy operability, and the results have also been verified by running confirmation tests. [ABSTRACT FROM AUTHOR]

Pipe cutting technology plays an important role in the process of offshore platforms decommissioning, as many devices such as tubing, drill pipe, and casing need to be decommissioned. In this study, a novel cutting pipe technology based on electro-discharge machining (EDM) is proposed, and a cutting pipe mechanism is developed to cut the pipes for decommissioning offshore platforms. The machining principles and characteristics of the technique are described. The effects of machining parameters, including tool polarity, dielectric fluid, electrode material and width, pulse on-time, pulse off-time, peak voltage, and electrode rotation speed to machining performance, are investigated. The material removal rate (MRR) of the machined casing and tool electrode wear ratio (EWR) is obtained based on the calculation of the percentage of mass loss per machining time. The experimental results show that a better cutting performance can be obtained with negative tool polarity at the conditions of dielectric fluid of emulsion, pulse on-time of 500 μs, pulse off-time of 200 μs, peak voltage of 70 V, copper electrode width of 28 mm, and electrode rotation speed of 250 rpm is a better choice. Additionally, the cutting slots surface has been investigated by the means of SEM. The cutting slots machined by the rotary EDM are clean and smooth. [ABSTRACT FROM AUTHOR]

The machining characteristics of electrical discharge machining (EDM) directly depend on the discharge energy which is transformed into thermal energy in the discharge zone. The generated heat leads to high temperature, resulting in local melting and evaporation of workpiece material. However, the high temperature also impacts various physical and chemical properties of the tool and workpiece. This is why extensive knowledge of development and transformation of electrical energy into heat is of key importance in EDM. Based on the previous investigations, analytical dependence was established between the discharge energy parameters and the heat source characteristics in this paper. In addition, the thermal properties of the discharged energy were experimentally investigated and their influence on material removal rate, gap distance, surface roughness and recast layer was established. The experiments were conducted using copper electrode while varying discharge current and pulse duration. Analysis and experimental research conducted in this paper allow efficient selection of relevant parameters of discharge energy for the selection of most favorable EDM machining conditions. [ABSTRACT FROM AUTHOR]

Electro-discharge machining (EDM) has grown tremendously over the last few decades. Due to its extensive capabilities, this technique has been increasingly adapted to new industrial applications within the field of aerospace, medical, die and mould production, precision tooling, etc. The novelty of the research presented in this paper lies in solving an inversion model, based on the least squares theory, which involves establishing the values of the EDM input parameters (peak current level, pulse-on time and pulse-off time) to ensure the simultaneous fulfilment of material removal rate (MRR), electrode wear ratio (EWR) and surface roughness (SR). The inversion model was constructed from a set of experiments and the equations formulated in the forward model described in the first part of this paper. In the forward model, the well-known ANOVA and regression models were used to predict the EDM output performance characteristics, such as MRR, EWR and SR in the EDM process for AISI 1045 steel with respect to a set of EDM input parameters. [ABSTRACT FROM AUTHOR]

Hybrid metal matrix composites are a class of material system, with two or more discrete particulate reinforcement. Notwithstanding their superior properties, their widespread application is constrained by the difficulty in machining them. Non-conventional processes such as electrical discharge machining can be applied to machine such composites. This work reports on the application of EDM to machine cast aluminum–silicon carbide–boron carbide and cast aluminum–silicon carbide–glass hybrid metal matrix composites and how the metal removal rate and surface finish vary in response to the various EDM parameters [ABSTRACT FROM AUTHOR]

This paper deals with the effect of copper tool vibration with ultrasonic (US) frequency on the electrical discharge machining (EDM) characteristics of cemented tungsten carbide (WC-Co). It was found that ultrasonic vibration of the tool (USVT) was more effective in attaining a high material removal rate (MRR) when working under low discharge currents and low pulse times (finishing regimes). In general, the surface roughness and the tool wear ratio (TWR) were increased when ultrasonic vibration was employed. It was observed that application of ultrasonic vibration significantly reduced arcing and open circuit pulses, and the stability of the process had a remarkable improvement. This study showed that, there were optimum conditions for ultrasonic assisted machining of cemented tungsten carbide, although the conditions may vary by giving other input parameters for those which had been set constant in the present work. [ABSTRACT FROM AUTHOR]