Search

The topic of waste combustion/co-combustion is critical, given the increasingly restrictive legal regulations regarding its environmental aspects. In this paper, the authors present the test results of selected fuels of different compositions: hard coal, coal sludge, coke waste, sewage sludge, paper waste, biomass waste and polymer waste. The authors conducted a proximate and ultimate analysis of the materials and mercury content in them and their ashes. An interesting element of the paper was the chemical analysis of the XRF of the fuels. The authors conducted the preliminary combustion research using a new research bench. The authors provide a comparative analysis of pollutant emissions—especially mercury emission—during the combustion of the material; this is an innovative element of this paper. The authors state that coke waste and sewage sludge are distinguished by their high mercury content. The value of Hg emission during the combustion depends on the initial mercury content in the waste. The results of the combustion tests showed the adequacy of mercury release compared to the emissions of other compounds considered. Small amounts of mercury were found in waste ashes. The addition of a polymer to 10% of coal fuels leads to a reduction in mercury emissions in exhaust gases. [ABSTRACT FROM AUTHOR]

A high static load state significantly increases the risk of rock burst occurrences on the island working face, posing a significant threat to the safety of coal mine production. This paper focused on the engineering background of the 8204-2 working face at Tashan Coal Mine. Field research indicated that there were noticeable differences in the frequency of coal bursts in different regions and working face ranges, with the mine pressure being complex and severe. Through theory analysis, the stress concentration degree of the island working face was mainly affected by the buried depth, working face length, gob length, coal seam thickness, and coal pillar width. The stress distribution and plastic zone changes of the island working face, influenced by different factors, were studied by numerical simulation. The entity coal stress equation of the island working face was fitted and the mechanism of rock burst in the island working face was revealed. The research findings presented in this paper provide important theoretical support and technical guidance for the safe and efficient mining of island working faces. [ABSTRACT FROM AUTHOR]

This paper presents the results of the research on the structure and thermal properties of materials made from fly ash based on high-density polyethylene (HDPE). Composites based on a polyethylene matrix with 5, 10, and 15 wt% fly ash from hard coal combustion content were examined. Fourier transform infrared spectroscopy with attenuated total reflectance (FTIR-ATR) was used to identify characteristic functional groups present in the chemical structure of polyethylene and the composites based on its matrix. Structural analysis was performed using X-ray diffraction (XRD), a differential scanning calorimeter (DSC), and microscopic examinations. Mechanical properties were also examined. Analysis of the thermal effect values determined by the DSC technique, XRD, and FTIR-ATR allowed the evaluation of the crystallinity of the tested materials. Polyethylene is generally considered to be a two-phase system consisting of crystalline and amorphous regions and is a plastic characterized by a significant crystalline phase content. Based on the FTIR-ATR spectra, DSC curves, and XRD, the effect of the filler and the changes occurring in the materials studied resulted in a decrease in the degree of crystallinity and a change in the melting point and crystallization temperature of the polymer matrix were established. Microscopic examinations were carried out to analyze the microstructure of the composites to collect information on the distribution and shape of the filler particles, indicating their size and distribution in the polymer matrix. Furthermore, the use of scanning electron microscopy combined with energy-dispersive X-ray spectroscopy (SEM-EDS) allowed for the microanalysis of the chemical composition of the filler particles. [ABSTRACT FROM AUTHOR]

The work presents a detailed analysis of the possibilities of the thermal processing of clay raw material granulates in a fluidized bed reactor powered by coal fuel. Potential customers of calcined granulates include the following: plants producing refractory materials for the steel industry, producers of refractory concrete, sanitaryware plants, tile plants, large-size tile plants, industry abrasives, chemicals, paints, paper, food and medical industries and others. The advantage of the presented fluid bed calcination technology is the possibility of the continuous operation of the reactor and the short time of the material in the bed, compared to the previously used methods of calcination in a shaft and rotary kiln, which lasts less than twenty minutes in the temperature range of 650–850 °C. During the experimental studies of calcination in the fluidized bed layer, the influence of the type of coal, its particle size and the mass share of coal in the feed mixture on the calcination process and the final product obtained was analysed. As a result of the conducted research, it was proven that solid fuels such as anthracite and steam coal type 31.2 (flaming) can be successfully used in the fluidized bed calcination process of clay materials. The key parameter determining the fluidized bed calcination process is the fuel particle distribution. [ABSTRACT FROM AUTHOR]

Shallow-buried, hard, and extra-thick coal seams are very common in Xinjiang, China, but there are relatively few studies on the mine pressure law and the development characteristics of water-flowing fracture zones (WFFZs) during the mining of such coal seams. In this paper, the mine pressure of the top coal caving face in a shallow, hard coal seam with a hard roof and full bedrock (SHCSHRFB) is analysed, the laws of the surrounding rock deformation and stress of the open-off cut and roadway in the large-mining-height top coal caving face are studied, the characteristics of roof-breaking and overburden fracture development are analysed using the physical similarity simulation method, supporting suggestions for roadways are put forward, and three development stages of the WFFZ are analysed. Field monitoring shows that the hydraulic support stress in SHCSHRFB is weak, but the coal wall and roadway stability are good, which is significantly different from the results in the typical shallow-buried thin bedrock working faces. The measured height of the WFFZ is close to the physical similarity simulation results, but quite different from those arising from use of the empirical formula. [ABSTRACT FROM AUTHOR]

The issue of transport in underground hard coal mines is very rarely described in the literature. The financial aspects of this issue are even less often analyzed. Publications in this area focus on technical issues and the safety of mining crews. More attention is paid to transport in open-pit mines. The above premises and practical needs imply the need to conduct economic analyses of transport systems in underground hard coal mines. This paper is a scientific communication, which presents the concept of a multi-criteria cost analysis as a tool to support the selection of the optimal transportation option in an underground hard coal mine. Considerations in this area have not been carried out in the relevant literature, and the problem of selecting a transportation option is a complex and necessary issue in the practice of underground mines with extensive mine workings. The methodology presented includes five cost criteria (costs of carrying out the transportation task; route expansion costs; rolling stock maintenance costs; depreciation costs; and additional personnel costs). The simultaneous application of criteria relating to utility properties in addition to cost criteria makes it possible to adopt a specific technical and organizational model of the transportation system based on the indication of the optimal solution, resulting from the mathematical construction of functions of objectives relating to utility and cost. The optimal variant of the designed system and configuration of the material transportation system in underground workings takes into consideration the following: (1) seven utility criteria (KU1—transportation task completion time; KU2—compatibility of transportation systems; KU3—continuous connectivity; KU4—co-use with other transportation tasks; KU5—safety; KU6—inconvenience; KU7—operation under overplanning conditions) and (2) five cost criteria (KK1—costs of implementing the transportation task; KK2—costs of route expansion; KK3—rolling stock maintenance costs; KK4—depreciation costs; KK5—additional personnel costs). Based on the aforementioned criteria, two objective functions are built for each option: utility and cost. They present divergent goals; therefore, they are non-cooperative functions. Both utility and costs strive for the maximum. In the developed methodology, an ideal point is usually a fictitious solution representing a set of maximum values among all the achievable values in a set of solutions, but it is impossible to achieve this simultaneously based on all the criteria. This point illustrates the maximum utility and lowest cost among the alternatives considered, which is obviously impossible for any of the variants to meet at the same time, although it indicates the possibilities of the technique and the range of costs. For the developed method, a so-called "PND" nadir point is also determined, representing the least-preferred level of achievement of all goals simultaneously, determined from the set of optimal points in the Pareto sense. The originality of the conceptual considerations undertaken stems from: filling the gap in the economic methodology of complex transportation systems evaluation; embedding considerations in the trend concerning complex transportation systems of underground mines; and focusing considerations on the pre-investment phase, making it possible to optimize costs before expenditures are incurred. [ABSTRACT FROM AUTHOR]

The torrefaction process represents a thermal conversion technique conducted at relatively low temperatures ranging between 200 to 300 °C. Its objective is to produce fuel with a higher energy density by decomposing the reactive portion of hemicellulose. In this study, the kinetics of mass loss during torrefaction were investigated for willow. The experiments were carried out under isothermal conditions using thermogravimetric analysis. Batch torrefaction reactor designs were conducted and explained in detail. Co-combustion of willow with hard coal (origin: Katowice mine) in different mass ratios (25% biomass + 75% coal, 50% biomass + 50% coal, and 75% biomass + 25% coal) was conducted in addition to raw biomass torrefaction. TG/MS analysis (a combination of thermogravimetric analysis with mass spectrometry analysis) was performed in the research. The optimal torrefaction conditions for willow were identified as an average temperature of 245 °C and a residence time of 14 min, resulting in the lowest mass loss (30.15%). However, it was noted that the composition of torgas, a by-product of torrefaction, presents challenges in providing a combustible gas with sufficient heat flux to meet the energy needs of the process. Prolonged residence times over 15 min and higher average temperatures above 250 °C lead to excessive energy losses from volatile torrefaction products, making them suboptimal for willow. On the other hand, the co-combustion of torrefied biomass with hard coal offers advantages in reduced sulfur emissions but can lead to increased NOx emissions when biomass with a higher nitrogen content is co-combusted in proportions exceeding 50% biomass. This paper summarizes findings related to optimizing torrefaction conditions, challenges in torgas composition, and the emissions implications of co-combustion. [ABSTRACT FROM AUTHOR]

This paper discusses the impact of coal abrasive materials of varied petrographic composition and claystones containing admixtures of coal matter on the surface wear of wear-resistant martensitic steels. Wear tests were conducted at a test stand for three petrographic varieties of hard coal: vitrinite, clarinite, and durinite, and five samples of claystone. These tests revealed no significant effect of the type of coal abrasive used on the value of mass loss from the surface of the wear-resistant steel samples. The reason behind the foregoing is the observed tendency of coal abrasives, irrespective of their petrographic variety, to penetrate surface irregularities, especially those attributable to previous surface treatment of the samples and the impact of wear products. The dominant forms of surface damage were surface fatigue chipping and scratches caused by the particles which detached themselves from the surface of the steel samples, as observed for all the analysed coal variants. On the surfaces of the samples seasoned in the presence of claystones, highly varied forms of damage were observed: microcutting, scaly surface cracks, delamination, and deep cracks. In these cases, it was possible that the abrasive grains had been pressed into the steel surface irregularities, but no layered forms of the pressed-in abrasive material were observed to have developed. The paper also presents a model for the formation of coal films and discusses their possible effect on wear minimisation. [ABSTRACT FROM AUTHOR]

This paper presents the jig operating properties of the selected final parameters of the hard coal concentrate. The quality parameters of the product, such as the yield and ash content, were evaluated in terms of the technical and hydrodynamic parameters of the jig's operation. The research program included a series of experiments in which the efficiency and the amount of hutch water were changed. The variables selected and analyzed were divided into two categories, i.e., one related to the characteristics of the concentrate produced, and the other to the characteristics of the jig operation. Models were built for narrowed particle size fractions based on concentrate yield and ash content in the concentrate. In addition, a multidimensional analysis was performed, considering variables such as machine throughput, which was determined by the flow rate of the material, the amount of hutch water, the quality of the concentrate, and the amount of concentrate, as well as the accuracy of the jig operation expressed by the imperfection. Two main parameters were taken into account for modeling the operation to examine their significance of influence on the final responses in terms of the possibility of adjusting the value of independent settings of the jig operation. The presented approach to modeling the operation of the jig can be extended by considering the impact of other parameters, taking into account the variability of the final effect, as long as it is allowed under the industrial conditions of machine operation and the assumed production requirements. The approach presented in this paper is a new technique, which was not found in the literature. [ABSTRACT FROM AUTHOR]

Underground mining in coal mines causes strong disturbance to geological structures and releases a large amount of elastic strain energy. When the roof is a hard and thick rock layer, it is easy to cause dynamic disasters such as rock burst. To analyze the impact of a deep thick and hard roof fracture on the safe mining of thick coal seams, this paper studied the dynamic evolution process of the stress field, displacement field, energy field, and plastic zone of the coal seam and overlying strata during the mining process using FLAC3D numerical simulation. The results show that as the working face continues to be mined, the concentrated stress in the overlying strata first increases and then decreases, and the support pressure in front of the working face continues to increase. When it advances to 100 m, collapse occurs, and the stress increases sharply; the bottom plate undergoes plastic failure, resulting in floor heave. The overlying strata mass in the top plate exhibits downward vertical displacement, while the rock mass in the bottom plate exhibits upward vertical displacement, with a maximum subsidence of 4.51 m; energy concentration areas are generated around the working face roadway, forming an inverted "U" shape. When collapse occurs, the energy density decreases slightly; the direction of the plastic zone changes from "saddle shaped" to complete failure of the upper rock layer, and the overlying strata is mainly shear failure, which expands with the increase in mining distance. The research results have important practical significance for guiding the safe mining of deep thick and hard roof working faces. [ABSTRACT FROM AUTHOR]

The underground coal gasification (UCG) technology converts coal into product gas and provides the option of environmentally and economically attractive coal mining. Obtained syngas can be used for heating, electricity, or chemical production. Numerous laboratory coal gasification trials have been performed in the academic and industrial fields. Lab-scale tests can provide insight into the processes involved with UCG. Many tests with UCG have been performed on ex situ reactors, where different UCG techniques, the effect of gasification agents, their flow rates, pressures, and various control mechanisms to improve gasification efficiency and syngas production have been investigated. This paper provides an overview of recent research on UCG performed on a lab scale. The study focuses on UCG control variables and their optimization, the effect of gasification agents and operating pressure, and it discusses results from the gasification of various lignites and hard coals, the possibilities of steam gasification, hydrogen, and methane-oriented coal gasification, approaches in temperature modeling, changes in coal properties during gasification, and environmental risks of UCG. The review focuses on laboratory tests of UCG on ex situ reactors, results, and the possibility of knowledge transfer to in situ operation. [ABSTRACT FROM AUTHOR]

The current problems associated with the maintenance of hard coal longwall mining depend on the application or use of extraction technologies. In order to make the best use of these technologies, a new approach based on simulation studies is necessary. This paper aims to develop a mathematical model for the powered roof support's operation. The three groups of professionals involved in the testing of the roof support were involved in the work on changing the hydraulic system of the powered roof support stand. These professionals were powered roof support's designers, researchers and users. The research subject was the development of a mathematical model as a starting point for conducting simulations. The model is based on d'Alembert's principle and the equation of the balance of flow rates. Based on the developed model, it is possible to determine the pressure in the space under the piston of the hydraulic prop. The results obtained in the simulations are the basic assumptions for the development of a prototype that would solve the current problems in the hydraulic systems of powered roof supports. The adopted research methodology assumed the development of a mathematical model, simulation in the MATLAB environment and verification of the model on a test stand. The obtained results of simulation tests based on the developed mathematical model were confirmed in bench tests. Simulation and bench tests determined the correctness of the assumptions made for the development of the prototype model. Based on the analysis of the results, the nature of the work of the future prototype has been predetermined. The next stage will be the testing of the prototype, which is to be included in the hydraulic system of the prop of powered roof support in the future. The model mentioned before is the baseline model, and it will be modified depending on the application of the future design in real conditions. Simulation studies of powered roof support will allow the structure that is used currently to be optimised, so as to adapt it to increasingly difficult working conditions. [ABSTRACT FROM AUTHOR]

Graphite can be artificially converted from anthracites under high temperatures; however, the exact mechanism through which inorganic minerals contribute to the graphitization process is still unknown. In light of this, several selected minerals in different amounts were added to demineralized anthracite coal. The anthracite–mineral mixtures were subjected to artificial graphitization experiments under temperatures ranging from 1700 to 2900 °C in the laboratory. The obtained series of coal-based graphites with various levels of graphitization were characterized by X-ray diffraction (XRD), and the derived structural parameters, such as d002 and FWHM (002), La, and Lc were used to compare the carbon structural evolution during the high temperature treatment and mineral catalytic graphitization. Moreover, the amorphous carbon of anthracite is eventually transformed into the highly ordered crystalline carbon of coal-based graphite. The five added minerals show interesting structural variation during the graphitization process, in which pyrite is decomposed into iron (Fe), illite, quartz, and kaolinite, which can react with disordered carbon in organic matter to form moissanite (SiC), while dolomite seems to react with sulfur to form oldhamite (CaS). At temperatures less than 2300 °C, the minerals could significantly enhance the catalytic effect. There is a clear difference in the catalytic effect of different minerals on graphitization. Kaolinite exhibits the strongest catalytic effect. The minerals dolomite, illite, and quartz only show a certain degree of catalysis. Pyrite, however, only has a limited effect on improving the degree of graphitization at a temperature of 1700 °C. However, once the temperature exceeds 2300 °C, the dominant factor controlling the graphitization of anthracite appears to be the temperature. According to the growth pattern at microcrystalline sizes (La and Lc), the minerals' catalytic effects can be classified into three groups. The first group includes minerals that preferentially promote La growth, such as pyrite, illite, and quartz. The second group includes minerals that preferentially promote Lc growth, such as dolomite. Finally, kaolinite is in a separate group that promotes microcrystal growth in both the lateral and vertical directions simultaneously. The mechanisms of the minerals' catalytic graphitization are discussed in this paper. The promotion role of minerals in the artificial graphitization process may help to optimize the graphitization process and reduce the process cost in the future. [ABSTRACT FROM AUTHOR]

This paper investigates the removal efficiency of a honeycomb electrostatic precipitator (ESP) applied to control particulate matter (PM) emissions from a small-scale boiler with combustion lignite and hard coal. The specifics of the precipitation of emissions from small-scale boilers are discussed, and the design principles for relevant ESPs are presented and used. The ion-induced nucleation of sulfuric acid occurred, causing the drastic penetration of 19 nm particles through the ESP. Despite this, the overall collection efficiency was sufficient to meet the EU's Ecodesign Directive requirements. Back corona was not detected. The optimal ESP performance is defined with further parameters: a current density of 0.5 mA/m2 at an electric field strength of about 2.7 × 105 V/m; a minimal specific collecting area of ESP (SCA) of 60 m2/(m3/s); and Nt-product of 4.5 × 1014 s/m3. Such parameters of ESPs should ensure adequate PM emissions control for any type of boiler with similar emissions characteristics. The composition of collected fly ash particles was analysed, and a method for fly ash utilisation was proposed. This research may be helpful for designing ESPs to control PM emissions for small-scale units with fossil fuel combustion. [ABSTRACT FROM AUTHOR]

Although highly developed countries are trying to diversify away from coal-based energy, many economies rely on this resource. Its consumption results in the production of carbon dioxide, which promotes global warming, necessitating its sequestration. This paper presents the sorption–dilatometric relationships of hard coal samples differing in vitrinite and inertinite content. The studies were carried out under isothermal conditions (298 K) at a free pressure drop complemented by measurements under non-isothermal conditions (298 K to 323 K). The tests were performed on an original apparatus, based on the operation of an Arduino microcontroller. For the natural porosity to be preserved and for a better representation of the behaviour of the coal–gas system, samples in the form of cuboidal blocks were used, making this apparatus unique worldwide. Based on the study, it appears that the difference in petrographic composition affects the behaviour of the coal structure, influencing differences in the sorption–dilatometric properties. In the case of the sample with higher vitrinite content, the amount of adsorbed gases is higher. [ABSTRACT FROM AUTHOR]

As one of the main fossil fuels globally, coal can be enriched with a variety of critical metal elements in specific geological conditions. This paper investigates the mineral compositions and concentrations of major and minor element oxides and trace elements in the No. 9 coal from the Xinyuan mine of the northern Qinshui coalfield, China, and discusses the modes of occurrence and enrichment mechanisms of critical metal elements such as Li, Ga, Th and REY. The mineral compositions of the No. 9 coal are primarily represented by clay minerals and quartz, with a small amount of calcite, siderite, anatase, etc. The major element oxides in the No. 9 coal are dominated by SiO2 and Al2O3. Compared with world hard coal, the No. 9 coal of the Xinyuan mine is rich in Li (CC = 8.00) and Th, slightly enriched with Pb, Sc, Ga, Y, La, Ce, Tb, Dy, Er, Yb and Hg, and depleted in Mn, Co, Ni, Rb, Cs and Tl. The critical metal elements such as Li, Ga, Th and REY that enriched No. 9 coal mainly occur in aluminum silicates. The genetic type of the critical metal elements in the No. 9 coal from the Xinyuan mine is source rock-controlled type. The critical metal minerals and solutions from the source area were transported to the study area by the action of water. Due to the change of swamp water conditions, the critical metal elements were combined with clay minerals and enriched the coal. [ABSTRACT FROM AUTHOR]

Poland is a big user of fossil fuels for electricity and heat production. The most important fossil fuel is hard, brown coal and the Polish energy system is based on this source. However, the world has begun to decarbonize the climate and reduce the carbon dioxide and methane which are the main gasses impacting climate change. The main aim of this paper was to recognize changes in Polish coal sector. We focused our attention to the economic situation and employment in coal sector in Poland. The time rage included 1989–2020 and the prognosis 2021–2025. The Polish coal sector faced dramatic changes. The number of hard coal mines decreased from 70 in 1990 to 21 in 2020. In the same timeframe, the prices for hard coal increased from 12.37 PLN/dt to 313.27 PLN/dt. The employment decreased from more than 350 thousand to less than 100 thousand people in hard coal mines. The decrease changes are the effect of strict policies of the European Union. The economic situation of Polish hard coal mines is rather poor. Polish mines achieved negative economic results due to the effect of poor management. We used advanced statistics, including the Augmented Dickey–Fuller test (ADF), to measure the stationarity of analyzed time series. We also used Generalized AutoRegressive Conditional Heteroskedasticity (GARCH) models and conducted a prognosis. Our research proved that the time series describing the hard coal economic situation were not stationary. The Generalized AutoRegressive Conditional Heteroskedasticity (GARCH) models confirmed big changes in Polish coal sector economic results. The elaborated prognosis of variables proved that the price of hard coal will increase in 2021–2025. Moreover, the economic situation will be worse. Our analysis confirmed that global trends of the hard coal sector were influenced by the European Union (EU) energy policy and closing down the mines. The economic situation of Polish hard coal sector worsened. [ABSTRACT FROM AUTHOR]

Backfilling technology is not always used by mining enterprises, which is conditioned by technological and economic factors, such as the need for high mining rates and costs for the technological processes of transporting backfill materials from the daylight surface to the mined-out space. This concerns the underground mining of hard coal, which is a strategic energy resource, in the mines of Ukraine. This paper aims to study the effect of leaving the waste bottom rocks in the mined-out space of the longwall face without their drawing to the earth's surface on the geomechanical state of the rocks surrounding the longwall face. The geomechanical assessment of the stress state of the rock mass surrounding the longwall face, when leaving the waste rocks from the seam bottom rocks in the mined-out space, is performed by the finite element method using the Ansys software package. A geomechanical model has been developed and substantiated, which adequately reflects the mining-geological conditions for seam mining within the extraction site, the actual structure and properties of the coal-bearing rock stratum, the parameters of the longwall face and the modified powered support for the processes of leaving the rocks in the mined-out space. The values and patterns have been determined of the decrease in the stress intensity concentrations in the coal-bearing roof mass in the frontal bearing pressure zone and destressing zone with an increase in the ratio of the rock pack thickness to the extracting seam thickness. The relative indicators of the load on the powered support section and the lowering of its roof have been determined by the ratio of the thickness of the rock pack formed in the mined-out space to the extracting seam thickness. The proposed mining method is of significant commercial and research interest for owners of coal mines developing thin coal seams because environmental costs for placing waste on the surface are reduced, and the energy potential of coal is increased due to the separation of waste rocks from coal in underground conditions. The need for a cycle of beneficiation of mined mass is eliminated and the geomechanical conditions of coal mining processes are improved. [ABSTRACT FROM AUTHOR]

The rapid development of science and technology, and the restructuring of the mining extraction industry, bring about profound changes in the structure and complexity of technological equipment used in mining. In this paper, the Reliability Centered Maintenance (RCM) method has been applied to analyze the components of the KSW-460NE shearer machine, which fails quite frequently. The cutter drums do not match from a constructive point of view, and the concrete operation conditions, alongside the picks (being in direct contact with coal and hard inclusions) and guides are submitted to intense abrasion wear, showing a great number of failures. The data collected following the machine's exploitation allowed parameter determination characterizing the reliability of the components mentioned, the manner of failure, and the effects. Using calculation methods, it has been possible to facilitate the interpretation of the result in view of establishing measures required to improve maintenance of the dominant components of the machine, determining replacement intervals, in accordance with an imposed reliability and maintainability. The results of the study assist in the choice of suitable hardening materials for the reconditioning of cutter drums and guides that are necessary for practical trials, by which their operating times, and replacement intervals, respectively, might be additionally improved. [ABSTRACT FROM AUTHOR]

Coal wall rib-spalling is regarded as a key technical problem influencing safe and efficient mining of fully mechanized working face with great mining height (FGH) while the coal wall stability is influenced by the strength of the coal body, of which the internal joint fissures have a crucial impact on the strength of the coal body. This research attempted to explore how the coal wall stability of FGH is influenced by the occurrence of joint fissures. This paper uses physical and numerical simulations to systematically analyze the instability characteristics and displacement law of FGH. Research results show that the form and scope of the instability of coal wall rib-spalling depend on the state of the coal seam joint fissures development area, and the development state of coal seam joint fissures is related to the combination of the coal seam joints; under the condition of hard coal, the coal wall stability is better at the inclination angle of 90°, and less stable at 45° and 135°; under the condition of medium-hard coal and joint surface inclination angle of 45° and 135°, the smaller the spacing of joint surface, the larger the area of the working face rib-spalling, and the less stable the coal wall. [ABSTRACT FROM AUTHOR]

The COVID-19 pandemic with subsequent economic fluctuations during consecutive epidemics waves and preventive measures in the form of lockdowns, and Russia's invasion of Ukraine have had a meaningful impact on the European economy, including the energy market. These events have caused an increase in the prices of many products, including fossil fuels, and also a lack of their availability. The changes inspired the authors to conduct research on the current situation in Poland in the field of renewable energy and coal. The paper describes the research on the impact of the development of RES (mainly photovoltaic sources) on the change in the energy generation profile in the case of Poland. The article analyzes the impact of RES (renewable energy sources) on the reduction of CO2 emissions. The conducted analysis was based on the historical similarity of the replacement of conventional (carbon) sources by PV (photovoltaics) by determining in how many cases (%), a specific carbon source will be displaced. Based on the prepared forecast, it was determined that by the end of the year, the installed capacity in PV will reach the level of 11,213 MWp (in wind energy, it will be 7875 MWp). Replacement (reduction of consumption) of approximately 1.5 million Mg of hard coal and 2.87 million Mg of lignite was concluded to be possible (~4.4% and 6.3% of the hard-coal and lignite volume used for energy production). Limiting this volume of hard coal and lignite will also reduce CO2 emissions in the entire NPS by 5.24 million Mg (−5%) in 2022. [ABSTRACT FROM AUTHOR]

Limestone flour is used in a variety of industrial sectors such as power and heat generation, glass-making, paper-making, the construction industry and construction materials manufacturing, the production of agriculture, plastics and rubber goods, as well as coal mining, and environmental protection. This paper aims to characterize and interpret the limestone flour supply and demand trends in the main applications in Poland in the last decade. In order to track the changes of domestic consumption for this commodity, its major users have been surveyed along with analyses of data from the Statistics Poland (GUS). The results showed that during 2009–2018 the coal-fired power plants became the biggest customer of limestone flour utilized as a sorbent in the wet flue gas desulfurization method (FGD). This method has been implemented in the vast majority of Polish power plants. It is estimated that in the last decade the total annual production capacity of limestone flour at the milling plants in Poland increased by 1.5 million tons, to around 6.0 million tons. In the forthcoming years, this is expected to continue to increase despite EU restrictions on fossil fuel use (especially hard coal and lignite). Other promising areas of future growth are: for limestone flour of medium quality—the construction materials manufacturing and the construction industry itself, for limestone flour of the highest quality—the glass industry, while for fine-grained limestone flour of high-quality—the plastics and rubber industries. In terms of resource security, it is worth noting that Poland is a country rich in limestone deposits. However, only some of them, that is, limestone rock varieties of the Jurassic and Devonian ages from the Kielce vicinity in central Poland are suitable for the production of high-quality limestone flour for the needs of the mentioned industries. The paper analyses the potential of the limestone flour production from the available limestone rock deposits with respect to the current and future needs of the domestic market in Poland. [ABSTRACT FROM AUTHOR]

The date assumed as the beginning of the pandemic in Poland is 4 March 2020, the date of the first confirmed case of the virus. This article presents the actions undertaken by the management of underground hard coal mining plants concerning the risk of epidemic related to SARS-CoV-2. This work shows a set of implemented recommendations, guidelines and decisions, which were established after the appearance of the first wave of cases in Poland. What is more, it discusses measures aiming at reducing the risk of spreading the coronavirus among the mineworkers. The suggestions for different variants of the decision-making process concerning the pandemic and which have an enormous impact on the operating expenses of the company are also made. The paper presents the results of the study on actions taken in individual mining companies and good work practices recommended to be applied. [ABSTRACT FROM AUTHOR]

The content of natural methane in hard coal seams, called methane-bearing capacity, is the basic parameter that enables the level of methane hazard to be determined in hard coal mines. This parameter is also used to determine the potential quantities of methane that can be collected and used for energy purposes and the amount of its harmful emission to the atmosphere. Direct methods are most often used to determine methane-bearing capacity. An important aspect that has a great influence on the final result of the research is the gas losses generated at the stage of sampling. Under the conditions of the Polish mining industry, the direct drill cuttings method is used to determine the methane-bearing capacity. Gas losses are compensated for in this method with the use of the coefficient 1.12, by which the obtained result is multiplied. In this paper, a multi-parameter analysis of gas loss in the determination of methane-bearing capacity in hard coal seams has been carried out. Several experiments were performed to identify the most important aspects to be taken into account to obtain a correct result. A methane-bearing capacity test was conducted using two direct methods: the direct drill cuttings method, otherwise known as the single-phase vacuum degassing method, and a method based on the United States Bureau of Mines standards. Sorption studies, such as methane sorption kinetics tests, were also conducted in which sorption properties, such as sorption capacity, effective diffusion coefficient, and half sorption time, were determined. Methane sorption isotherms were also determined, and pore structure was analysed. Based on the obtained test results, an analysis was carried out which made it possible to present appropriate conclusions concerning the gas losses during the methane-bearing capacity test, generated at the stage of sampling. The final result of the work was the proposal of a new gas loss coefficient for the direct drill cuttings method of methane-bearing capacity determination. [ABSTRACT FROM AUTHOR]

The Young's modulus and Poisson's ratio, parameters reflecting the elastic response of a rock to stress, are the key parameters used in many engineering activities, such as hard coal mining and natural gas extraction. The objective of this paper was to present the results of complex laboratory measurements of the static and dynamic Young's modulus and Poisson's ratio for Upper Carboniferous hard coals from the Upper Silesian Coal Basin. The coals differed in geologic age (Mudstone Series—younger coals; Upper Silesian Sandstone Series—older coals) and petrographic structure (vitrain, clarain, and durain lithotype). Elastic parameters of the coals were determined following compression tests under a complex state of stress, as well as using the ultrasonic method in reservoir conditions. On this basis, linear functional dependences between parameters such as UCS, differential stress, confining pressure, strain rate, P- and S-wave velocities, and the static and dynamic Young's modulus and Poisson's ratio were determined. These dependences turned out to be linear, with strong and very strong correlation, as indicated by the high coefficients of determination, R2. These new results significantly broaden the knowledge of elastic properties of Carboniferous hard coals, especially in the field of geoengineering, underground coal gasification, and reservoir stimulation for coal bed methane extraction. [ABSTRACT FROM AUTHOR]

The paper presents a computer program called SubCom v1.0 for determining mathematical model parameters of compaction layers in areas of oil, gas or groundwater extraction. A stochastic model based on the influence function was used to model compaction and subsidence. Estimation of the model parameters was based on solving the inverse problem. Two model parameters were determined: the compaction coefficient Cm of reservoir rocks, and the parameter tgβ, which indirectly describes the mechanical properties of the overburden. The calculations were performed on leveling measurements of land subsidence, as well as on the geometry of the compaction layer and pressure changes in aquifers. The estimation of model parameters allows the prediction of surface deformations due to planned fluid extraction. An algorithm with a graphical user interface was implemented in the Scilab environment. The use of SubCom v1.0 is presented using the case of an underground hard coal mine. Water drainage from rock mass accompanying coal extraction resulted in compaction of the aquifer, which in turn led to additional surface subsidence. As a result, a subsidence trough occurred with a maximum subsidence of 0.56 m. [ABSTRACT FROM AUTHOR]

During the ventilation of longwalls in hard coal mines, part of the air stream migrates to the goaves with caving. These goaves constitute a space (void) filled with rocks following coal extraction. In the case where these goaves contain coal susceptible to spontaneous combustion, the flow of such an air stream through the goaves may lead to the formation of favourable conditions for coal oxidation, self-heating and spontaneous combustion. Such an area is referred to as the zone with a particularly high risk of spontaneous coal combustion (endogenous fires). The location and extent of this zone depend on many factors, with one of the most important being the permeability of the goaves which determines the tensile strength of the roof rocks forming the caving. This strength determines the propensity of these rocks to transform into the state of caving and the degree of tightness of the cave-in rubble (treated as a porous medium). The purpose of the present paper is to determine how the tensile strength of roof rocks influences the extent of the zone with a particularly high risk of spontaneous coal combustion (endogenous fires) in caving goaves of the longwalls ventilated with the Y-type system. To achieve this goal, model-based tests were conducted for a region of the longwall mined with caving and ventilated with the Y-type system. Critical air speed and oxygen concentration values in the caving goaves of this longwall were determined for the actual conditions of exploitation. These parameters define the risk zone of spontaneous coal combustion. The tests also helped to determine the extent of this zone, depending on the strength of the rocks forming the caving. The results obtained unequivocally indicate that the type of rocks forming the caving affects its permeability and the extent of the risk zone for spontaneous coal combustion. At the same time, the distribution of this zone is substantially different than in the case of other ventilation systems. The results obtained are of real practical significance for preventive measures to reduce fire risks. The effectiveness of these measures significantly improves the safety of mining exploitation. [ABSTRACT FROM AUTHOR]

Market-driven closures of coal mines have typically been associated with negative economic consequences for the affected regions. In Germany, structural policy directed towards ameliorating the negative effects of hard coal decline in the Ruhr area lagged behind the onset of decline, caused major political conflicts, and has been variously criticized for its reactive character that failed to generate a positive image of the future. The phase-out of lignite coal in Germany, in contrast, is policy-driven and accompanied from the outset by compensatory and investment policies that strive to facilitate regional structural change proactively. Against this backdrop, we investigate how the policies of lignite coal phase-out initiated in 2018 and the accompanying public discourse affect the economic worries of individuals in the remaining three lignite coal mining areas in Germany. We focus on the period 2016–2021, using a longitudinal multilevel design based on regional and individual data from the German Socio-Economic Panel (GSOEP). Overall, probabilities of strong economic worries decrease throughout the observed period. Results show that subjective economic worries do not significantly differ between residents of lignite mining regions and those in the rest of the country. Further robustness analyses confirm that the coal phase-out policy has not increased economic uncertainties in the populations of German lignite mining regions. Based on our results, we discuss the need for future research on the effects of policy designs of clean energy transitions on subjective perceptions of the future. [ABSTRACT FROM AUTHOR]

To reveal the influence mechanism of mining speed on roof fracture-type rockburst, the Brazilian split technique combined with acoustic emission monitoring technology was employed to study the effects of loading rates on the tensile failure characteristics and acoustic emission parameters of coal series sandstone. The linear relationship between the tensile strength of the samples and the change rate of tensile stress was determined. The mining speed was introduced into the mechanical model of initial and cyclic fracture of the hard roof, and the quantitative relationship between the maximum rate of change of tensile stress within the hard roof and the mining speed was derived. Based on this, a computational model for the bending elastic energy of the hard roof during initial and cyclic fractures, considering the mining speed, was established. The main findings are as follows: As the loading rate increases, the distribution range of acoustic emission energy in sandstone Brazilian split samples before failure widens, with a significant rise in acoustic emission ring-down counts and energy at failure. At lower loading rates, acoustic emission events primarily occur near sample failure, whereas at higher rates, they mostly happen in the early loading stage. The higher the mining speed, the less opportunity there is for internal micro-fractures to develop and expand before the hard roof fractures, which macroscopically results in increased tensile strength and a larger amount of energy released at the moment of fracture. Bending elastic energy rises approximately linearly with mining speed, and the thicker the hard roof, the more sensitive the bending elastic energy is to changes in mining speed. This effect is even more pronounced during cyclic fractures. Optimizing mining speed is crucial for preventing roof fracture-type rockbursts, especially in mining workfaces with thick and hard roofs. [ABSTRACT FROM AUTHOR]

Formed activated carbon (AC) is a multipurpose product with developed adsorption properties that is widely used in various areas of life. To create AC, hard coal has to go through various processes: grinding, granulation, carbonization, physical and/or chemical activation. Presented research was conducted in the professional company manufacturing activated carbons. Studied AC reached the demanded shape of grains thanks to binders added to granulation process. Research on the AC formed using new polymeric binders (applied so far in other branches: pharmacy and construction materials) is presented in this manuscript. Tested binders were not used before to manufacture ACs in the professional technological line. Such polymers as: sodium carboxymethylhydrocellulose (CMHC), poly[1-(2-oxo-1-pyrrolidinyl)ethylene] (POPE) and enriched methyl-hydroxypropyl cellulose MHPC were studied in this work. Conducted research has proven efficiency of 8% CMHC which allowed for proper granulation and carbonization and reached the best parameters. Single- and double-stage activation was investigated for AC with this binder. For newly manufactured AC BET surface and pore volume increased accordingly from 774 m2/g and 0.58 cm3/g (1-stage) to 968 m2/g and 0.72 cm3/g (2-stage). Chemical elemental features of surface of the best AC showed beside elementary carbon also calcium, silicon and aluminum ions as well as groups with an acidic character, phosphates, sulphates and chlorides. The new AC had a higher Mechanical Strength reaching 99.9% and a lower Ash content and Volatile Matter than AC manufactured with previous binder—molasse. The new AC is intended to be directed for full production line and implementation to usage after positive certification. It may be useful in water treatment. It will also find application in the treatment of industrial and municipal wastewater. [ABSTRACT FROM AUTHOR]

Fly ashes produced in huge amounts during coal combustion requires proper management. The purpose of this study was to determine the impact of fly ash from burning hard coal used in large doses (250, 500, 1000 and 2000 t ha−1) on soil properties and vegetation of fresh mixed coniferous forest within 43 years from the ash application. The experiment was established in the Podzols in the forest habitat of Czułów, Katowice Forest district, Upper Silesia, Poland. Eight tree species were planted in ridges created by ploughing: Pinus sylvestris, P. nigra, Larix decidua, Betula pendula, Quercus robur, Q., Acer pseudoplatanus and Fagus sylvatica. The changes in soil morphology caused significant transformations in the physical and chemical properties of the soil such as soil texture, pH, macronutrients (P, K and Mg) content and C:N ratio. Increasing of ash doses changed the granulometric composition of the soil levels from loamy sand (250 t/ha−1) to silt loam (2000 t ha−1). Initially, the acidic Podzols were alkalized under the influence of the fly ash and then acidified, possibly due to the impact of accumulated litter layers, and the reaction of organic soil horizons changed from strongly acidic (250–1000 t ha−1) to alkalis (2000 t/ha−1). The macronutrients content increased in proportion to the fly ash dose, but the subsequent acidification resulted in a gradual decrease in the macronutrients share in the soil layers. The value of the C:N ratio grew after the ash application and then it gradually reduced, even by half. The transformations of soil horizons' properties also increased the capacity of the soil sorption complex (CEC). All these processes led to a change in the trophic status of the habitat expressed by the soil habitat index (SIG) and the initial coniferous forest site can be classified as a mixed forest habitat even with the lowest ash dose used. The composition of plant communities developed forty years after the ash application was similar at the lower ash doses and the most frequent and abundant tree species were L. decidua, P. nigra and P. silvestris. B. pendula was previously co-dominant, but it was eliminated from the tree stands during the experiment. Planted trees characteristic of late stages of succession, such as Q. robur, Q. rubra, F. sylvatica and A. pseudoplatanus either did not survive or remained in very low quantities. The herb and moss layers developed in the process of spontaneous colonization, and together with the trees led to phytostabilisation of the bare substrates. After acidification of the topsoil horizons, the herb layers consisted mostly of coniferous, mixed, and deciduous forest species, and the most frequent or abundant were Lysimachia europea and Pteridium aquilinum. The moss layers were represented by coniferous forest flora. At the ash dose of 2000 t ha−1, Tilia cordata settled in one of the seral stages of spontaneous succession and this species dominated in the community and formed a dense tree stand. After the soil acidification, a shift from calcicole to calcifuge plant strategy took place among species of the herbaceous layer. The transformations of plant communities' composition occurred in relation to changes in the soil properties. [ABSTRACT FROM AUTHOR]

Energy transition is one of the main objectives of the European Union. Significant changes will mainly affect countries in which significant modifications will have to be made to their energy sources. The process will involve high investment in infrastructure and additional costs of the transformation, such as reduced production (which may affect the GDP value) in the economic sectors involved in the process. The aim of this article is to provide the energy transition community, namely the national economy in general and those involved in planning for structural change in particular, with the key lessons and challenges in researching the impact of production changes in the mining sector. This article also shows the relevance of the mining sector in the economy. Within this area, particular attention is given to the following issues: the impact of economic sectors on the country's GDP (gross domestic product); the identification of key sectors of the economy using the input–output method; the contribution of coal mining and the mining industry to Poland's GDP; an analysis of changes in the structure of Poland's economy using the input–output method; and the use of the input–output method in the context of changing/reducing the supply of economic sectors. [ABSTRACT FROM AUTHOR]

Acoustic emission (AE) can reflect the dynamic changes in a material's structure, and it has been widely used in studies regarding coal mechanics, such as those focusing on the influence of loading rate or water content change on the mechanical properties of coal. However, the deformational behavior of coals with various strengths differs due to the variation in microstructure. Hard coal presents brittleness, which is closely related to certain kinds of geological disasters such as coal bursts; soft coal exhibits soft rock properties and large deformation mechanical characteristics. Therefore, conclusions drawn from AE characteristics of a single coal sample have application limitations. This paper studies the deformation patterns and AE characteristics of coals with different strengths. A uniaxial compression experiment was carried out using coal samples with average uniaxial compressive strengths of 30 MPa and 10 MPa; the SAEU2S digital AE system was used to measure the AE counts, dissipation energy, and fracturing point distributions at each deformation stage of the different coals. The results show that the bearing capacity of hard coal is similar to that of the elastic stage and plastic deformation stage, but it may lose its bearing capacity immediately after failure. Soft coal has a relatively distinct stress-softening deformation stage and retains a certain bearing capacity after the peak. The AE counts and dissipation energy of hard coal are significantly higher than those of soft media, with average increases of 49% and 26%, respectively. Via comparative analysis of the distribution and development of internal rupture points within soft coal and hard coal at 15%, 70%, and 80% peak loads, it was observed that hard coal has fewer rupture points in the elastic deformation stage, allowing it to maintain good integrity; however, its rupture points increase rapidly under high stress. Soft coal produces more plastic deformation under low loading conditions, but the development of the fracture is relatively slow in the stress-softening stage. We extracted and summarized the AE characteristics discussed in the literature using one single coal sample, and the results support the conclusions presented in this paper. This study subdivided the deformation process and AE characteristics of soft and hard coals, providing a theoretical guidance and technical support for the application of AE technology in coal with different strengths. [ABSTRACT FROM AUTHOR]

The paper provides the analysis of fuel and energy transition in households sector and its sustainable development in the period 2004–2019. The main purpose of the paper is to determine the development trends in the use of renewable energy sources (RES) in the EU countries household sector in 2004–2019, to recognize the state of development and functioning of the studied area as well as to indicate their successes and shortcomings in observed reality. The article employs the results of Energy balance sheets from Eurostat. The research entity were households from 28 European Union countries, with particular emphasis on households from Poland and selected neighboring countries. The research subjects there were different sources of renewable energy used by households, i.e., solar thermal system, geothermal technologies, primary solid biofuels, charcoal, biogases, blended biogasoline, blended biodiesels, ambient heat (heat pumps). To achieve the research objective a number of statistical measures ands methods, including cluster analysis and linear trend indicator applied. In the analyzed 16 years, an absolute and relative increase in the use of RES in the household sector was noticed. Taking into account the specificity of using RES in households, 6 clusters of countries were distinguished. In Poland, it was noted that there was a significant increase in the use of RES in households, with stagnation in the use of non-renewable energy sources, such as, for example, hard coal. [ABSTRACT FROM AUTHOR]

The calculation method commonly used in the industry takes into consideration mainly fuel consumption (excluding electricity) and the amount of removed moisture which is reflected in the unit MJ·(Mg·%)−1. This is not a scientific approach because the result will change if the basic moisture is different (drying from 21% to 18% will consume less energy than drying from 18% to 15%). This paper aims to compare the energy consumption of two industrial continuous flow grain dryers powered by LPG and hard coal based on a comprehensive approach to energy efficiency calculation enriched with electricity consumption, flow measurements, and control of grain moisture. It could be useful for manufacturers who could use this method to generate more reliable data in their product datasheets, and it could also be legally regulated as an appropriate tool for calculating the energy consumption of agricultural grain dryers. According to the approach presented in this paper, the S428.CS construction powered by LPG gas had an energy consumption that was 6.14% lower than the DT2532 dryer construction, which used hard coal. [ABSTRACT FROM AUTHOR]

This paper reports the mineralogical and geochemical compositions of the Late Permian C2, C5a, C5b, C6a, and C6b semianthracite coals from the Mahe mine, northeastern Yunnan, China. Minerals in the coals are mainly made up of quartz, chamosite, kaolinite, mixed-layer illite/smectite (I/S), pyrite, and calcite; followed by anatase, dolomite, siderite, illite and marcasite. Similar to the Late Permian coals from eastern Yunnan, the authigenic quartz and chamosite were precipitated from the weathering solution of Emeishan basalt, while kaolinite and mixed-layer I/S occurring as lenses or thin beds were related to the weathering residual detrital of Emeishan basalt. However, the euhedral quartz and apatite particles in the Mahe coals were attributed to silicic-rock detrital input. It further indicates that there has been silicic igneous eruption in the northeastern Yunnan. Due to the silicic rock detrital input, the Eu/Eu* value of the Mahe coals is lower than that of the Late Permian coals from eastern Yunnan, where the detrital particles were mainly derived from the basalt. The high contents of Sc, V, Cr, Co, Ni, Cu, Ga, and Sn in the Mahe coals were mainly derived from the Kangdian Upland. [ABSTRACT FROM AUTHOR]

One of the ways used to reduce the emission of carbon dioxide and other harmful substances is the implementation of biomass co-firing processes with coals. Such processes have been implemented for many years throughout many countries of the world, and have included using existing high-power coal boilers. Despite numerous experiments, there are still no analyses in the literature allowing for their generalization. The purpose of this paper is to determine the generalized energy and ecological characteristics of dust steam boilers co-firing hard coal with biomass. The energy characteristics determined in the paper are the dependence of the gross energy efficiency of boilers on such decision parameters as their efficiency and the share of biomass chemical energy in fuel. However, the ecological characteristics are the dependence of emission streams: CO, NOx, SO2, and dust on the same decision parameters. From a mathematical point of view, the characteristics are approximation functions between the efficiency values obtained from the measurements and the emission streams of the analysed harmful substances and the corresponding values of the decision parameters. Second-degree polynomials are assumed in this paper as approximation functions. Therefore, determining the characteristics came down to determining the constant coefficients occurring in these polynomials, the so-called structural parameters. The fit of the determined characteristics was assessed based on the coefficients of random variation and the test of estimated significance of structural parameters. Boiler characteristics can be used when forecasting the impact of changes in operating conditions on the effects achieved in existing, modernized, and designed boilers. The generalization of the characteristics was obtained from the measurement results presented in 10 independent sources used to determine them. [ABSTRACT FROM AUTHOR]

The paper assesses the impact of combustion of biofuels produced based on municipal sewage sludge in stoker-fired boilers on the amount of pollutant emissions and examines the tendency of ash deposition of biofuels formed during the combustion process. The combustion tests were performed in a laboratory system enabling simulation of a combustion process present in stoker-fired boilers. The study was conducted for three types of biofuels; i.e., fuel from sewage sludge and coal slime (PBS fuel), sewage sludge and meat and bone meal (PBM fuel) and fuel based on sewage sludge and sawdust (PBT) with particle size of 35 mm and 15 mm. This paper describes and compares the combustion process of biofuels with different granulation and composition and presents the results of changes in emission values of NOx, SO2, CO, and CO2. The emission results were compared with the corresponding results obtained during combustion of hard coal. The results showed that biofuels with lower particle sizes were ignited faster and the shortest ignition time is achieved for fuel based on sewage sludge and coal slime-PBS fuel. Also, the highest NO and SO2 emissions were obtained for PBS fuel. During the combustion of fuel based on sewage sludge and meat and bone meal (PBM), on the other hand, the highest CO2 emissions were observed for both granulations. Biofuels from sludge show a combustion process that is different compared to the one for hard coal. The problems of ash fouling, slagging, and deposition during biofuels combustion were also identified. The tendency for ash slagging and fouling is observed, especially for fuel from sewage sludge and meat and bone meal (PBM) and fuel based on sewage sludge and sawdust (PBT) ashes which consist of meat and bone meal and sawdust which is typical for biomass combustion. [ABSTRACT FROM AUTHOR]

This paper presents a metamaterial sensor using a double slit complementary square ring resonator (DS-CSRR) that has been utilized for the measurement of dielectric materials, especially coal powder. The design is optimized for best performance of deep notch depth in transmission coefficient (Magnitude of S 21 ). Sensitivity analysis of transmission coefficient with respect to structure dimensions has been carried out. Metamaterial properties of double negative permitivity and permeability were extracted from the S–parameters of this sensor. The optimized structure is fabricated using low cost FR-4 PCB board. Measured result shows resonance frequency of 4.75 GHz with a deep notch up to −41 dB. Simulated and measured results show good agreement in desired frequency band. For material characterization, first, two known materials are characterized using this metamaterial sensor. Their respective resonances and dielectric constants are known, so the transcendental equation of the sensor is formulated. Afterwards, the proposed sensor is used for dielectric measurement of two types of coal powder, i.e., Anthracite and Bituminous. The measured value of dielectric constant of Anthracite coal is 3.5 and of Bituminous coal is 2.52. This is a simple and effective nondestructive measurement technique for material testing applications. [ABSTRACT FROM AUTHOR]

The introduced limits on carbon dioxide emissions by the European Union encourage experimental work on new-generation materials containing smaller amounts of clinker. Currently, silica fly ash from hard coal combustion is widely used in cement and concrete technology in Europe and Poland. Their wide application is determined mainly by the chemical and phase composition, and in particular by the activity of pozzolanic and its high fineness, like cement. The aim of this study was to assess the effect of glass flour and polypropylene fiber modifiers on the properties of concrete and its microstructure. To analyze the results, samples of reference ordinary concrete and samples with different amounts of glass flour (0–30%) and a constant number of polypropylene fibers (0.025 kg) were used. The obtained test results showed the possibility of producing ordinary concrete with the addition of glass flour. The average compressive strength for concrete containing 10% additive was set at 49.3 MPa, 51.2 MPa, and 53.1 MPa after 28, 56, and 90 days of maturation for a content of 20% of 44.6 MPa, 46.4 MPa, and 48.4 MPa, respectively, and for 30% of 41.5 MPa, 43.8 MPa, and 45.6 MPa, respectively. By modifying concrete with glass flour and polypropylene fibers, a composite resistant to negative temperatures can be obtained. Glass flour shows reactivity with the cement matrix, and in small amounts, it might cause the microstructure to seal and a slight increase in compressive strength. [ABSTRACT FROM AUTHOR]

A novel coking wastewater treatment technique is proposed based on the principles of the circular economy. By utilizing coal as an adsorbent for organic pollutants in coking wastewater, the treated coal can be introduced into the coking system after the adsorption and flocculation sedimentation processes. This creates a closed-loop system with zero coking wastewater emissions. We investigated the potential of adsorption for the removal of pyridine. Batch experiments were conducted using lignite, coking coal, and anthracite as adsorbents. Both coking coal and anthracite showed favorable adsorption properties for the chosen contaminants. The experimental data were analyzed utilizing various models, including pseudo-first-order and pseudo-second-order kinetic equations, as well as intraparticle diffusion and Bangham. This study aimed to identify the rate-limiting step in the adsorption process. The results revealed that the adsorption of pyridine onto the three coal types followed pseudo-second-order kinetics. The rate-limiting mechanisms may include both boundary-layer diffusion and intraparticle diffusion. The effect of pH on coal adsorption and the activation energy of pyridine adsorption by coking coal were also examined. Adsorption offers a promising approach in advanced wastewater treatment, with coking coal emerging as a cost-effective adsorbent for addressing persistent organic pollutants during the adsorption process. [ABSTRACT FROM AUTHOR]

The article presents research on the possibilities of utilising the Lean Management method to increase the profitability of coal mining operations through cost rationalisation and production optimisation. The Lean Management method has its roots in the automotive industry, but its significant benefits can allow it to be transferred to other industries. Based on the analysis of global literature describing examples of its application in general mining, as well as the authors' own observations related to Polish hard coal mining, it was determined that the Lean Management method is not being utilised in this field. This article outlines the course and results of an original expert-mathematical study to assess the usefulness of specific Lean Management tools and techniques in hard coal mining. The study drew on knowledge obtained from selected, competent experts who demonstrated high levels of agreement in their assessments. Five core production areas were identified, and twelve widely used Lean Management tools and techniques were selected. The obtained assessments of the usefulness of Lean tools could serve as valuable guidance for mining management in the selection of methods for improving mining production in coal mines. [ABSTRACT FROM AUTHOR]

This paper presents the possibility of the energetic utilization of biowaste in the form of lignified one-year shoots from the cultivation of grapevines of the Seyval Blanc (WSBL), Solaris (WSOL), Regent (WREG) and Rondo (WRON) varieties, grown in temperate climate zones. A technical analysis, an elemental analysis and the determination of the highest heat value and lowest heat value were performed to define the quality parameters of waste as fuel. In addition, the emission factors of SO2, NOx, CO, CO2 and dust were estimated to demonstrate the impact of potential biowaste from combustion. Based on the stoichiometric equations, the exhaust gas composition, the theoretical oxygen demand and the total flue gas volume were evaluated. The study showed that the material with the highest energy potential was WREG (LHV-16.19 MJ·kg−1), with an ash content of 3.68%, while the lowest potential was found for WRON (LHV-15.88 MJ·kg−1), with an ash content of 4.21%. The study showed that the use of the studied viticulture waste instead of hard coal could reduce CO emissions by 26–27%, CO2 by 24–26%, NOx by 55–56%, SO2 by 96–97% and dust by 77–80%. [ABSTRACT FROM AUTHOR]

This paper analyses the function of an innovative integrated receiver for the measurement of electromagnetic field emissions. The autonomous receiver measures and registers the elevated emission levels of both components of the EM field originating from rocks subjected to increased mechanical stress. The receiver's sensitivity of 60 µV/m, its dynamic range of 98 dB, and its impulse response of 0.23 V/µs were determined in laboratory conditions. Real EM field signals from hard coal samples subjected to crushing force were recorded using an autonomous receiver. The observed and recorded results confirm that the receiver operates in the full range of amplitudes of the EM field signal emitted from the rock. The results determine the band of characteristic signals for EM field emission from hard coal. The system created on the basis of autonomous EM receivers can support the existing seismic safety systems in real mine conditions by predicting the possibility of mine collapse hazards. [ABSTRACT FROM AUTHOR]

The paper presents the results of an analysis of the impact of activities related to the implementation of Poland's climate policy on the level of demand for hard coal. The authors used sets of indicators built by Eurostat during the analysis. The analysis was based on a set of indicators that had not previously been used for this purpose. The applied ARAMAX model made it possible to study the impact of the presented indicators on the volume of demand for hard coal in Poland. They were introduced to the ARMAX model as explanatory variables. The demand for hard coal in Poland was the dependent variable. The set of indicators was verified, and finally only statistically significant factors were used to build the model. The forecast of the demand for hard coal was made until 2022. It showed that the volume of coal sales would systematically fall as long as factors affecting demand remain constant. However, an additional factor was taken into account in the analysis, namely the increase in demand and prices for hard coal on world markets. The ARIMA model was used to forecast price levels for the next 12 months. The forecast indicates that the time series of prices should maintain an upward trend within the examined time period. Building an accurate and reliable forecast is the basis for effective planning of coal production and is adjusted to the demand for this fuel. [ABSTRACT FROM AUTHOR]

This paper contains the results of research on a promising combustion technology known as chemical looping combustion (CLC) and chemical looping with oxygen uncoupling (CLOU). The remarkable advantages of CLC are, among others, that concentrated CO2 stream can be obtained after water condensation without any energy penalty for its separation or significant decrease of NOx emissions. The objective of this work was to prepare a novel bi-metallic Fe–Mn supported on ZrO2 oxygen carriers. Performance of these carriers for the CLOU and CLC process with nitrogen/air and hard coal/air was evaluated. One-cycle CLC tests were conducted with supported Fe–Mn oxygen carriers in thermogravimetric analyzer utilizing hard coal as a fuel. The effects of the oxygen carrier chemical composition and process temperature on the reaction rates were determined. Our study proved that for CLOU, properties formation of bixbyite and spinel forms are responsible. Among iron ferrites, we concluded that iron-rich compounds such as Fe2MnO4 over FeMn2O4 spinel type oxides are more effective for CLOU applications. [ABSTRACT FROM AUTHOR]

The ignition characteristics of coal dust is of high importance for the flame stability in coal-fired power plants. We investigate the ignitability of six lignite dust qualities and one hard coal using dust explosion tests and an ignitability characteristic number. The paper aims to identify the degree of impact of the properties of coals, such as the moisture content, the ash content etc., on the ignition characteristics and ultimately to compare the identified relevant ignition parameters to the ignition performance of the dust qualities in an industrially relevant environment. The minimum cloud ignition temperature (MCIT), the maximum rate of pressure rise ((dp/dt)max), the maximum explosion pressure (pmax), the deflagration index (Kst-value) and the modified ignitability characteristic number (ZWZmod.) were determined and were attributed to the moisture content, the ash content and the median particle size. The MCIT was largely influenced by the volatile content, whereas the variations of moisture and ash contents within the range of 10% to 20% did not have a significant impact on the MCIT. The maximum explosion pressure did not differ considerably and stayed in a narrow range among the tested dust qualities. The deflagration index showed a higher sensitivity to the dust properties. The deflagration index and the modified ignitability characteristics number dropped as the moisture content increased and the volatile content reduced. The Kst and ZWZmod. values showed the highest susceptibility to the coal dust properties. Hence, they were used as representative parameters for further comparison with the ignition performance of coal dust in a pilot-scale testing. The results showed that both parameters predicted the ignition performance relatively well and can be used as indicators for the prediction of the ignition performance. [ABSTRACT FROM AUTHOR]

Fractal derivatives characterize the accelerated creep phase of the creep process. In this study, based on the fractal order theory, the integer-order derivatives are defined from the spatio-temporal self-similarity phenomenon of the dynamic process using the scale change method, and the viscoplastic model is improved to establish a new creep instantonal model with damage to describe the complete creep phase of anthracite. The effects of damage variables on initial and accelerated creep were investigated by performing graded-loading creep tests. Based on the experimental data, inversions of the model-related parameters were performed, and parameter sensitivities were analyzed. The results show that the proposed model can better characterize the complete creep process of anthracite coal, which verifies the correctness and rationality of the model. The damage content affects the initial and accelerated creep strain under different loading levels, and a specific functional relationship exists between them. The study's findings can provide some reference material for the stability control of anthracite affected by disturbing stresses. [ABSTRACT FROM AUTHOR]

Coal permeability data are critical in the prevention and control of coal and gas outbursts in mines and are an important reservoir parameter for the development of coalbed methane. The mechanism by which permeability is affected by gas pressure is complex. We used a self-developed true triaxial seepage experimental device that collects lignite and anthracite coal samples, sets fixed axial pressure and confining pressure, and changes gas pressure by changing the orientation of the coal seam to study the influence of the gas pressure on the permeability of the coal seam under the conditions of different coal types and different bedding orientations. Coal permeability decreased rapidly and then decreased slowly and tended to be stable with the increase in gas pressure. This conformed to the power exponential fitting relationship, and the fitting degree reached more than 99%. The comparison of the two anthracite coal samples showed that the sample's permeability with a bedding plane vertical to the seepage direction was significantly lower than that of the bedding plane parallel to the seepage direction, indicating that gas seeped more easily along the bedding. The sensitivity coefficient of permeability with the change in gas pressure was calculated. The analysis showed that coal permeability was sensitive to changes in gas pressure during the low-pressure stage. When the gas pressure was greater than 0.8 MPa, the sensitivity coefficient was significantly reduced, which may have been related to the slow increase in the amount of gas absorbed by the coal seam in the high-pressure stage. A theoretical calculation model of coal seam permeability considering adsorption/desorption and seepage effects was proposed and then verified with experimental results showing that the theoretical model better reflected the permeability characteristics of coal and predicted its permeability. Using the finite element simulation software COMSOL, the extraction efficiency of the coal seam gas under different gas pressure conditions was simulated. The results showed that coal permeability and extraction efficiency decreased with an increase in gas pressure. In the low-pressure stage, the reduction in the extraction efficiency was more evident than that in the high-pressure stage. [ABSTRACT FROM AUTHOR]