Search

The improvements in signal-to-noise ratio (SNR) are indispensable to obtain the desired output signal of partial discharge (PD) under square wave pulsewidth modulation (PWM) voltage. In this article, the effect of complex PWM voltage parameters (rise time, fall time, frequency, duty cycle) on the SNR of PD tests is investigated. The results revealed that the sensor's high-frequency gain should be increased to improve the SNR under faster switching. PD impulses are more likely to be submerged in the residual interference under high-frequency voltage. The SNR can be improved by only detecting the PD at the rising front because the PD signal overlaps with commutation noise at the falling front of short duty cycle voltage, such as 0.03% duty cycle. The above results can reference the PWM parameters and improve the SNR in PD tests for rotating machines controlled by power electronics. [ABSTRACT FROM AUTHOR]

A novel single-phase pulsewidth modulation (PWM) direct ac–ac converter based on two-level nondifferential dual-buck ac chopper legs with inverting and noninverting operations is first proposed in this article. It has the ability to resolve both voltage sag and swell problems at the same time when used as distributed flexible voltage conditioner. Compared to the traditional ac–ac converter, it has much enhanced system reliability thanks to no shoot-through problems even when all switches of each ac chopper legs are turned on, and therefore, the PWM dead time is not needed leading to improve the utilization of the duty cycles. Only half of the switches in the proposed converter is switched at high frequency during a switching period at most, which significantly reduces the total switching loss. In particularly, the converter has two greatest advantages that it retains the common sharing ground of the input and output and has the same buck/boost operation process for noninverting and inverting modes. In order to fully testify the performance of the proposed converter, a 500-W experimental prototype is built and tested at different conditions. [ABSTRACT FROM AUTHOR]

Repetitive control strategies have been commonly applied in pulse-width-modulated (PWM) voltage source inverters (VSIs) for many industrial applications. This paper presents a repetitive controller for voltage harmonic mitigation of VSI-based islanded microgrids. The phase delay in the overall control system, e.g., the delay caused by the digital duty cycle calculation, PWM generation, and repetitive controller, has to be compensated by elaborately designed phase lead filters in order to prevent control performance deterioration and system instability. Nevertheless, quantificational analysis and practical design of the time advance unit in such filters are hardly found in existing literature works. In view of this, this paper proposes an explicit analysis of the phase lead filters and a novel design method of the time advance unit in repetitive controllers to ensure system stability. Moreover, with the help of the proposed method, the overall system stability margin is predictable and improved controller performance is achieved as well. The proposed method is implemented experimentally to show the accurate stability margin calculation as well as the excellent steady state and dynamic performances of the repetitive control scheme. [ABSTRACT FROM PUBLISHER]

Conventional centralized control strategies may reduce the flexibility and expandability of a modular multilevel converter (MMC) system. To tackle this issue, this paper proposes a distributed control architecture that is capable of assigning certain control tasks to distributed local controllers and improves the modularity of an MMC system. A central controller dealing with the output current regulation based on sensed arm currents is adopted. The control of MMC internal dynamics and the pulsewidth modulation (PWM) generation are distributed into local controllers. Unlike the conventional MMC control that needs all submodule capacitor voltages for capacitor voltage averaging, the proposed capacitor voltage control only relies on local submodule voltage measurement. Consequently, communication-intensive capacitor voltage transmission in each control cycle is not required and the communication burden of the control system can be significantly reduced. The control loops and possible control conflicts among submodules are presented and considered for system stability analysis. The effectiveness of the proposed distributed control architecture and capacitor voltage control for an MMC are confirmed by the start-up, steady state, and transient experimental results. [ABSTRACT FROM PUBLISHER]

In this paper, a modified one-cycle-control (OCC) scheme is proposed for regulating three-phase pulsewidth-modulated (PWM) rectifiers operating under unbalanced and distorted supply conditions. Mathematical analysis is first presented to show the dominant harmonic-voltage components appearing across the dc link of the PWM rectifier when it is controlled by an existing OCC scheme. Such dc-link harmonics when produced may aggravate harmonic currents flowing into the input terminals of the three-phase rectifier. To address these interrelated unbalance and harmonic concerns, the concept of reconstructing the appropriate reference signals in the OCC control core is introduced, before modifications are recommended for altering the key control equation. The improved OCC controller eventually developed is proven to exhibit minimal input-current distortion and a smoother dc-link voltage without using large capacitance. Other advantages exhibited by the traditional OCC scheme, such as no phase-locked loop, no frame transformation, and constant switching frequency, are also retained by the improved controller, whose theoretical findings are fully verified by experimental results obtained from a 1.2-kW three-phase PWM rectifier built in the laboratory. [ABSTRACT FROM PUBLISHER]

This paper introduces a novel H-bridge structured ac–ac pulsewidth modulation (PWM) converter topology based on two-level non-differential ac chopper legs, which can work at the non-inverting and inverting modes for the utility voltage compensation. Compared to the traditional bipolar-type H-bridge ac–ac converter, no bidirectional switches are switched in a complementary manner to overcome the commutation problem due to the delayed response of electronic circuits and semiconductor switching devices. The detailed PWM control signals and operational principles are presented to regulate the output voltage in a bipolar manner. Especially the main advantage is that the proposed ac–ac converter has the same buck/boost operation process for non-inverting and inverting modes, which ensures the continuously average current supply to the low-voltage output side without a high-value capacitor to support power. Additionally, due to the common sharing ground of the input and output, the feature that output can reverse or maintain phase angle with input is supported well. Then, the detailed analysis, design conditions, and experimental verification based on a 1 kW experimental prototype are presented. [ABSTRACT FROM AUTHOR]

This paper introduces a compensation strategy to deal with both current and voltage measurement errors in the three-phase pulsewidth modulated rectifier system. The dc offset and scaling errors in the voltage and current measurements cause the injection of undesired dc and unbalanced currents into the three-phase input current and subsequently lead to voltage ripple at the dc output voltage. This paper proposes a compensation scheme for current measurement error where the dc offset and scaling errors in the current measurement are estimated from the characteristic of the dc output voltage ripple combining with simple band-pass and low-pass filters. Meanwhile, an advanced current controller designed with a proportional integral plus two resonant controllers tuned at the fundamental grid frequency $({{\omega _s}})$ and $2{\omega _s}$ in the synchronous (d–q) reference frame is suggested to reject the impact of the dc offset and scaling errors in the voltage measurement. The proposed compensation method is developed without the need of extra hardware circuit, sensor, or precise information of system parameters so that it can be considered as more cost-effective and robust solution. The effectiveness of the proposed solution is verified by experimental results. [ABSTRACT FROM AUTHOR]

A high-performance three-phase pulse width modulation (PWM) converter with reduced dc-link capacitor under unbalanced ac voltage conditions is proposed in this paper. The unique feature of the converter lies in that sinusoidal symmetrical ac currents and ripple free dc voltage can be achieved simultaneously without using a bulky capacitor, which was thought to be a dilemma in the past. The control scheme is implemented in an α–β frame, so the complex rotate transformations are avoided, and it does not require the extraction of positive and negative sequence currents, which simplifies the control algorithm. A two-quadrant operation active power compensator together with its controller is developed to suppress the voltage ripple in the dc-link. Compared with the passive compensation method, the compensator is equipped with a smaller capacitor to reduce the system size, weight, and cost. Moreover, the compensator could be integrated with the conventional three-phase three-leg PWM converter seamlessly. The effectiveness of the proposed control schemes is verified by the experiment results. [ABSTRACT FROM PUBLISHER]