Search

The extensive application of vector phase shift modulation method in permanent magnet synchronous motor drive systems with single dc-link current sensor results in obvious current ripple in the low-speed region. The patterns of these ripples vary greatly in different sectors, leading to nonnegligible phase current reconstruction errors. In this article, an estimation of the local average current change rate (ELAC2R) based reconstruction error suppression method within the switching cycle is proposed to resolve this problem. By comparing the actual and the ideal sampling points, the increase of current ripple and the reconstruction error caused by the combination of the vector phase shift and the single current sensor sampling in the low-speed region are modelled and analyzed. Then according to equivalent modelling of the current ripple between the ideal and the actual sampling points, the more accurate phase current information can be quickly obtained based on the sampling value. The compensation process is significantly simplified and the computation burden of the processor is reduced. Experimental results show that the performance of current reconstruction can be improved effectively with less harmonic content with the proposed method. [ABSTRACT FROM AUTHOR]

Because of the time-sharing sampling logic, the three-phase currents reconstructed by single dc-link shunt present significant errors in the permanent magnet synchronous motor drives. A traceback-prediction current correction method for sampled currents is proposed in this article to eliminate the reconstruction errors. According to the analysis of time-sharing sampling errors, the concept of equivalent current change rate during one pulsewidth modulation (PWM) period is introduced, and the phase current characteristic model based on state observer is established. Both the equivalent and instantaneous current change rates can be obtained by the observer-based calculation method. In order to improve the current reconstruction precision, the ultimate values of three-phase currents can be predicted by adopting the proposed traceback-prediction current correction method, which does not require major computation and is easy to implement with no restrictions on the PWM strategy. The effectiveness of the proposed method is verified by experimental results. [ABSTRACT FROM AUTHOR]

Droop control is broadly used in dc power distribution systems, e.g., dc microgrids. Implementing droop control for switch mode power supplies requires the measurement of average current. Synchronous sampling is used in digital control systems to obtain the average of a triangular inductor waveform. However, the dead time, semiconductor turn-on and turn-off delays, and signal conditioning delays shift the sensed waveform and change the effective duty cycle, resulting in a misalignment and measurement error from the average value. This paper proposes a duty cycle weighted averaging method based on double sampling. By sampling twice per switching period and averaging the results using duty cycle as the weighting factor, the error due to waveform misalignment is theoretically eliminated. The result always equals the average value of the triangle. This method does not rely on the knowledge of circuit delays, making it easy to implement and robust to parameter variations. Simulations and experimental measurements validate the superior performance compared with conventional single and double sampling methods. The experiment on a droop-controlled dc–dc converter demonstrates a more accurate droop characteristic. [ABSTRACT FROM AUTHOR]

The current reconstruction strategies using single current sensor in the motor drives are widely researched. However, the sampled currents do not represent the average values within the modulation period, especially for the asymmetric modulation or asymmetric sampling solutions. This is due to the following two reasons: 1) The detected current values obtained at different sampling points are utilized to calculate the three-phase currents; and 2) the detected instantaneous currents are applied to estimate the average current values. In this letter, the current change rates under different action vectors are estimated to compensate these errors in a three-phase four-switch interior permanent magnet synchronous motor (IPMSM) drive with single current sensor. The effectiveness of the proposed strategy is verified by experimental results on a 5-kW IPMSM motor prototype, which shows that the current reconstruction errors are reduced after compensation. [ABSTRACT FROM AUTHOR]

In this paper, a novel scheme for the estimation of the equivalent series resistance (ESR) of the dc-link electrolytic capacitor in three-phase ac/dc pulsewidth-modulation converters is proposed for condition monitoring. First, a controlled ac current component is injected into the input. Then, it induces ac voltage ripples on the dc output. By manipulating these ac voltage and current components with digital filters, the value of the ESR can be calculated, where the recursive least squares algorithm is used for reliable estimation results. In addition, the value of the ESR is corrected by considering the temperature effect, for which a simple temperature-sensing circuit has been designed. The simulation and experimental results show that the estimation error of the ESR is within a reasonable range, thereby enabling the determination of the appropriate time for the replacement of the capacitor. [ABSTRACT FROM PUBLISHER]