Search

An atomic implantation method was used to modify diatomite with CuCl. The CuCl/diatomite samples were characterized by different techniques, including FTIR, XRD, BET, SEM-TEM, EDX, and CO-TPR. Characterization results revealed the formation of CuCl particles of 50–60 nm highly dispersed on diatomite surface. CO adsorption measurements showed that 2CuCl/diatomite exhibits the highest CO adsorption capacity among all CuCl-modified samples with diatomite. Its CO adsorption capacity of 2.96 mmol/g at 30°C is 10 times higher than that of unmodified diatomite (0.29 mmol/g). The CO adsorption on CuCl-modified diatomites was found to fit well with the Langmuir–Freundlich model. [ABSTRACT FROM AUTHOR]

Catalytic ozonation is a new method used for removal of NH4OH solution. Therefore, high catalytic performance (activity and selectivity) should be achieved. In this work, we report the synthesis and catalytic performance of Fe2O3-Co3O4 modified dolomite in the catalytic ozonation of NH4OH solution. Dolomite was successfully activated and modified with Fe2O3 and Co3O4. Firstly, dolomite was activated by heating at 800°C for 3 h and followed by KOH treatment. Activated dolomite was modified with Fe2O3 by the atomic implantation method using FeCl3 as Fe source. Fe2O3 modified dolomite was further modified with Co3O4 by precipitation method. The obtained catalysts were characterized by X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), energy-dispersive X-ray spectroscopy (EDS), scanning electron microscopy (SEM), N2 adsorption–desorption (BET), and temperature-programmed reduction (H2-TPR). From SEM image, it was revealed that nano-Fe2O3 and Co3O4 particles with the size of 80–120 nm. Catalytic performance of activated dolomite, Fe2O3 modified dolomite, and Fe2O3-Co3O4 modified dolomite in catalytic ozonation of NH4+ solution was investigated and evaluated. Among 3 tested catalysts, Fe2O3-Co3O4 modified dolomite has the highest NH4+ conversion (96%) and N2 selectivity (77.82%). Selectivity toward N2 over the catalyst was explained on the basis of bond strength M-O in oxides through the standard enthalpy Δ H ° f of oxide. Catalyst with lower Δ H ° f value has higher N2 selectivity and the order is the following: Co3O4 (Δ H ° f of 60 kcal (mole O)) > Fe2O3 (Δ H ° f of 70 kcal (mole O)) > MgO (Δ H ° f of 170 kcal (mole O)). Moreover, high reduction ability of Fe2O3-Co3O4 modified dolomite could improve the N2 selectivity by the reduction of NO3- to N2 gas. [ABSTRACT FROM AUTHOR]

Al-incorporated SBA-15 samples (xAl/SBA-15) were successfully prepared by "atomic implantation" method. The samples were characterized by X-ray diffraction spectroscopy (XRD), transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDX), N2 adsorption-desorption isotherms (BET), and temperature-programmed desorption (NH3-TPD). In this catalyst, metal oxide species were highly dispersed on the SBA-15 surface and existed as isolated atoms. It was shown that the Al incorporation lead to the formation of medium and strong acid sites. The catalytic activity and selectivity were tested in a mild hydrothermal process for degradation of cotton cellulose to 5-hydroxymethyl furfural (5-HMF). A cellulose conversion of 68.5% and 5-HMF selectivity of 62.1% after 2 h of reaction at 170°C were achieved. The very high 5-HMF yield (42.57%) obtained in this paper is much higher than that was reported in the literature. [ABSTRACT FROM AUTHOR]